Lets say i have two machines on public ips. If i get incoming traffic on machine #1 on port 55242 i would just like to forward it to machine #2 on port 35000.I would just like to use machine #1 same way as a dns server works. It just redirects the traffic and tells the client where to go.
View 6 RepliesI'm trying to use iptables in order to forward all the incoming packets for port 5555 to port 5556 on the same server (192.168.2.101).
I wrote the following commands:
iptables -A PREROUTING -t nat -i any -p tcp --dport 5555 -j DNAT --to 192.168.2.101:5556
iptables -A FORWARD -p tcp -m state --state NEW -d 192.168.2.101 --dport 5556 -j ACCEPT
I'm using a Debian servers, as router/firwall.. I've two ethernet interfaces into the server, one for wan and one for lan. The i use SNAT so my LAN clients can access the internet throgh the debian router. That is working... Now i want to be able to access servers on the LAN site from the WAN site, and i wanna use port address translation (PAT). I have a FTP server running on a lan server, so i'm trying to portward port 21.
iptables -t nat -A PREROUTING -p tcp -i eth1 -d (WANIP) --dport 21 -j DNAT --to 192.168.1.2:21
When people try to access my FTP from the WAN site, they are redirected to the local FTP server, and they are promted for crendentials, but when the credentials are typed, and the local ftp server should answer the wan request, the connections dies.
The wan clients are being promted for credentials, so they are redirected to the local lan server, but after that the connections dies, so i think there is some kind of nat problem, when the local lan server is trying to respond to the wan request..
Here i my iptables script:
#flush table
iptables -F
#input regler
[code]....
I need to forward a port to use dtella. I'm using Fedora 10, using iptables for my firewall.
I'm currently trying to forward it from terminal with this command:
Code:
sudo iptables -t nat -A PREROUTING -p udp -i eth0 -d [ip address] --dport 11823 -j DNAT --to 192.168.0.2:80
this is what I get from iptables -L
Chain INPUT (policy ACCEPT)
target prot opt source destination
ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED
[Code].....
If I forward port 80 to port 3128 for squid with an iptable rule, does port 3128 have to be open on the firewall or is this all routed behind the firewall?
View 4 Replies View RelatedI`m running a rather simple iptables script, but no matter what port i try to forward it wont open. Here are the basics:
Code:
ipt="/usr/sbin/iptables"
$ipt -F
[code]...
How can I drop or forward a incoming connection from a part of a host like *.alicedsl.de
For example:
The user is connection from *.alicedsl.de on port 12345
So how can I drop this connection or forward to google.com on port 80
Having trouble visualising how IP-Based Virtual Host (with SSL) would work. Here is my vhosts.conf file:
Code:
#Define Name Virtal Host
NameVirtualHost 10.10.0.54:80
#Used to replace the main server host. The log file will reside in /var/log/httpd/error_log
[Code]....
How will it work? I will need to forward port 443 to the 10.10.0.55 interface right? Without doing that, there is no way this is going to work... is there? And that means that I can't run more than 1 ip-based SSL virtual host on one machine because I can't forward 443 to two different interfaces.
Also, do I use internal ip address or external ip address in the <VirtualHost > tag? I only have one static public ip.
I have 2 servers..
let say server A and server B
On server A open ssh is configured and is running on port 2298. So from my machine I can login there using ssh on port 2298
But when I login to server B and from there I try to connect to server A I cannot.
ssh: connect to host <ipaddress here> port 2298: Connection refused
So here is my issue in a nutshell. I need to take FTP requests that hit Server_A and forward them to Server_B. Server_B is not natted...Server_B is another public server in a completely different location in the world. One thing to note is that I only have one NIC hence why you will see both in and out being eth0. This is what I have in my iptables on SERVER_A:iptables -A FORWARD -p tcp -i eth0 --sport 21 -o eth0 -d SERVER_B --dport 21 -m state --state NEW -j ACCEPTiptables -A FORWARD -p tcp -i eth0 --sport 20 -o eth0 -d SERVER_B --dport 20 -m state --state NEW -j ACCEPTI've also tried both of the above without the --sport option. When I FTP to SERVER_A (where the above iptables rule are) it connects to SERVER_A instead of forwarding them to SERVER_B.
View 1 Replies View RelatedI have three machines on three networks192.x.x.x10.x.x.x172.x.x.xThe routers are set to forward communication between 192. network and 10. network, and between the 10. network and the 172. network.However, there's not routing between 192. and 172.I want to fix that by using a machine on the 10. network to forward communication between the other two networks.The machine has one etherent connection eth0 whose address is 10.1.1.11I set up an aliased ip address eth0:0 to be 10.1.1.12 using Quote:ifconfig eth0:0 10.1.1.12Then I tried to set forwarding rules the 10. machine such that 10.1.1.12 address will provide access to the machine 172.1.1.55 as followsQuote:# iptables -t nat -A PREROUTING -d 10.1.1.12 -j DNAT --to-destination 172.1.1.55The default policies for all chains is ACCEPT.I then try to access 10.1.1.12 from 192.1.1.20 expecting it to actually access 172.1.1.55 ; it does not work
View 3 Replies View Relatediptables and multiple public-facing IP addresses. With the current setup I have a public-facing firewall with iptables which will then forward traffic to a LAN IP. I will hopefully be allotted 1 private IP per public IP, which I hope will make this much more simple. For example, I have server A with the LAN IP of 10.0.0.1 which I would like to have traffic forwarded from 5.0.0.1, the public IP. I also have server B with LAN IP of 10.0.0.2 which I would like to have forwarded from 5.0.0.2, the second public IP. From what I have read and understood, this should be a simple task, however I would just like to double check to make sure that it is in fact possible, and if so, how would it be recommended that I go about doing so. Essentially, I need to forward each public IP to a corresponding LAN IP with all ports.
View 3 Replies View RelatedThe goal is to make connection calls (ssh, ping, ...) possible from one LAN (LAN-1) to a number of (at the moment two) separate smaller LANs.These smaller LANs (LAN-2a, LAN-2b, ...) have exact same specifications (same IP range, same number of nodes, ...)!The idea is to use a Fedora box (release 14 with 2.6.35.6-45.fc14.i686) and implement an appropriate iptables routing/forwarding.The Fedora box has three network interfaces:
- eth0 (aaa.bbb.ccc.m) on LAN-1 (aaa.bbb.ccc.0/24)
- eth1 (ddd.eee.fff.n) on LAN-2a (ddd.eee.fff.0/27)
- eth2 (ddd.eee.fff.p) on LAN-2b (ddd.eee.fff.0/27)
[code]....
I have a mail server on which I would like to block port 25 on my eth0 for everyone except our external spam filter. the problem is that I want our users to be able to connect via port 10025 which is forwarded to port 25, which then is blocked...
View 2 Replies View RelatedI'm using Fedora Core5.0 I have using Iptables for forward port 80 to port 3128(Squid) in the same of server.I need to forward using Iptables to use the other proxy server because this server i am use for vpn and mail tranfer.What a Commnand for i use?ase 1. Server 1 >Ip 192.168.0.4 SQUID WITH PORT(3128)2. Server 2 IP 192.168.0.254 PF SENSE (3128) I will use server 2 for using internet connect only.
View 1 Replies View RelatedWell I have been searching for more than a month now and I think I have read every single post related to this subject and finally decided to make a thread.
Now before I begin I am running Openvpn on my CentOS VPS. I have set static IP's for everyone.
Now what I am looking for is this lets say one of my clients wants port 60005 forwarded through my VPS to the internet what are the correct commands to run.
server-ip:60005 to loacl-ip:60005
Sever IP 24.xx.xx.xx
Client IP 192.168.1.2
I have a host and a client both running linux. Host has internet through eth2. Client needs to share that connection. The computers are connected directly using a crossover. I can ping from both fine. I figured I needed to port forward eth2 to eth0 to gain internet access in the client. How?
Code:
eth0 Link encap:Ethernet HWaddr 00:26:18:a6:fd:a3
inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::226:18ff:fea6:fda3/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]...
I can't port forward to ftp behind my firewall, I tried several attempts but none worked.
Can anyone help me solve this?
I have just set up the transmission bittorrent client on my server (using the web interface), and am trying to get the port forwarding right. After noticing low download speeds (and rare uploading), I decided to check if a port needed to be forwarded.
I found many conflicting sites, mentioning both the ranges 6881-6999 and the port 51413 (as well as TCP and UDP versus just TCP). My current configuration is to forward TCP and UDP port 51413 to my server.
I like to set in iptables to allow access from one host to my server on any ports.
Currently the iptables have been configured to deny all and to allow access only to those I've specified.
Can anyone advice on the command to achieve this?
I am trying to set up a DMZ host - that is, one multifunctional PC between the WAN and the LAN. I've started with a basic router, and expanding upon that as the need arises. I am currently trying to gain access (from the WAN) to a website hosted on one of the servers in the LAN, but I am having trouble accessing the host from the WAN; I think my iptables configuration may be too restrictive. On the DMZ host, I'm using Debian (Etch). I have setup dhcp3-server, a script to configure iptables and pound (reverse-proxy). The (virtual) machine has 4 network cards: eth0, eth1, eth2, eth3; eth0 is the WAN, eth1 through eth3 serve 3 different virtual LANs.
All machines in the LAN (except one windows 2008 server - I might want to address that problem later) get their IP adresses correctly via dhcp from the DMZ host. All machines on the LAN can access the internet (including the 2008 server if I configure it manually) as they should. If I access http://localhost on the DMZ host, pound reports "The service is not available. Please try again later." - as it should.
I can ping the DMZ host from the WAN on 10.0.0.79 However, if I try to access the DMZ host from the WAN (http://10.0.0.79) I get "Unable to connect" from firefox. I'm sure this is not a pound problem, so I think it's in the iptables, or maybe I should be installing some extra software that I'm unaware of.
[code]....
iptables -A INPUT -p udp --dport -j ACCEPT
iptables -A INPUT -p tcp --dport -j ACCEPT
iptables -A FORWARD -p udp --dport -j ACCEPT
iptables -A FORWARD -p tcp --dport -j ACCEPT
and the rules are placed in iptables, i can see them when I do iptables -L. But when I do netstat -an | grep 161 I can see that port 161 (SNMP) is not listening. Why?
I like to set in iptables to allow access from one host to my server on any ports.Currently the iptables have been configured to deny all and to allow access only to those I've specified.
View 2 Replies View RelatedI am running a voip server on port 5060. I want to hide this to all the robots scanning the net permanently - I know this is not enough security - it is just to prevent them from wasting by bandwidth testing all usernames until fail2ban stops them !
I'd like to have port 5060 accepting requests only from 'trusted' hosts, while others (client with dynamic ip) use port 5065 - thus, port 5060 will only appear open for some trusted partners and the bots will skip to something else.
I have setup the iptables rules succesfully to accept only trusted hosts.
-A RH-Firewall-1-INPUT -s 93.x.y.z -p udp -m state --state NEW -m udp --dport 5060 -j ACCEPT
-A RH-Firewall-1-INPUT -p udp -m state --state NEW -m udp --dport 5060 -j DROP
I've added a PREROUTING NAT rule that change the port from 5065 to 5060 for others - but then, this gets caught in the INPUT rule as port 5060 -A PREROUTING -p udp -m udp --dport 5065 -j DNAT --to-destination 192.168.1.1:5060
This works so well that the packets coming on port 5065 are translated to port 5060 and get caught in the DROP rule...
I have a CentOS box which is Internet Facing. It has 3 LAN's connected to it which are for virtual machines.
I want to port forward port 445 to a machine on one of the LAN interfaces. I have tried various ways to get it done, but still cannot access that port from the interface. I definately know device hosting port 445 is live, as I can ping it from the CentOS box and use lynx to access it! (It's a web server)
iptables -t nat -A PREROUTING -i eth0 -p tcp -m tcp --dport 445 -j DNAT --to-destination 192.168.0.2:445
I've been Googling about port forwarding iptables and even though there's result and I've applied it in my script, I can't make iptables forwading request to another machine so I decided to ask help.
eth0 is my Internet Interface (1.2.3.4 is the public ip)
eth1 is my Lan Interface
eth2 is my DMZ Interface
[code]....
There is this server where in I want to use port redirection using iptables. For port redirection I have used nat table with PREROUTING chain and REDIRECT option. Like:
Code:
iptables -t nat -A PREROUTING -p tcp --dport pop3 -j REDIRECT --to-port 8110
It just does not work. I have tried to redirect other ports as well but nothing works.
[code]....
I have a server running debian squeeze and kvm to virtualize a Windoze box. It's setup to use NAT. This is because of limits on the network by the admin and unfortunately, there isn't a way to get around this.
View 1 Replies View RelatedI recently installed a new Ubuntu PC that runs iptables and PSAD. I had the same script on another Ubuntu PC, but when I copied the script onto the new PC, I got this error. I don't remember where I found the tutorial for this, all I know is that this is the script (Edited for my usage):
Code:
#!/bin/bash
# Script to check important ports on remote webserver
# Copyright (c) 2009 blogama.org
# This script is licensed under GNU GPL version 2.0 or above
[code]....
Safe.txt contains:
Code:
127.0.0.1
192.168.1.8
192.168.1.1
98.200.58.73
192.168.0.1
And the error message generated is:
Code:
root@NETWORK-SERVER:/var/ddosprotect# ./ipblock.sh
' not found.4.4: host/network `127.0.0.1
Try `iptables -h' or 'iptables --help' for more information.
' not found.4.4: host/network `192.168.1.8
[code]....
how do i enable or open port in the iptables
View 14 Replies View Related