i would like to connect an "e.system 1201" laptop to a "netgear dgn1000" router using a wireless connection, i can get a wired connection to work but not a wireless connection. i beleive the network card in the laptop is a "ralink wireless card for advent/e.system".could anybody tell me if any linux o/s is compatable with the wireless card.
View 3 RepliesA friend who switched ISP's gave me his old Linksys WRT54-G wireless router. I went through the installation procedure and had a wireless connection up and running - smiley face. I had security set up for WPA, and decided to upgrade it to WPA2. Another smiley face. When I went to connect (had already done so successfully), I noticed it referred to my wireless as Linksys - I was expecting to see the SSID. So I started playing around in Network Manager and now I have things all effed up.
Don't know exactly what I did, but now I have no wireless. So I ran a few commands (lshw -C network, iwconfig, ifconfig, and iwlist scan), and looking at the results I see what appear to be inconsistencies in the output. I've posted them below, and make the following observations:
1. Under the lshw it refers to my wireless connection logical name as wmaster0, and has the correct MAC address, etc.
2. Under the iwconfig it says, 'wmaster0 no wireless extensions', but then refers to wlan0 as the wireless connection (although it does not seem to be running).
3. Under ifconfig I see both a wlan0 and a wlan0:avahi. The wlan0 has no IP, the wlan0:avahi does, but it is incorrect.
[Code]...
Its a case of ".... wireless network connection active but still not internet connection .."I am using WEP - 128 key ... Works when I connect directly using ethernet cable ... but not wireless (pci and wireless router)
ubuadmin@ubucomputer:~$ ifconfig
wlan0 Link encap:Ethernet HWaddr 00:06:25:12:83:3b
inet addr:192.168.1.10 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::206:25ff:fe12:833b/64 Scope:Link[code].....
I have installed Fedora 11 recently. I want to share my Internet connection.
I have e LAN connection eth0 which is connected to internet.
I have a Wireless connection wlan0.
I want to share my internet connection with wireless connection.
My problem is exactly the same as [URL]
but I am stuck at the last hurdle
here are the output of the command that helped to solve the case in the previous post:
ifconfig wlan0
wlan0 Link encap:Ethernet HWaddr 00:1b:77:d2:59:55
inet6 addr: fe80::21b:77ff:fed2:5955/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
[Code].....
I have also tried sudo dhclient but it hasn't helped and I am still unable to connect to the internet
I have two linux laptops. Currently, I'm using both of them at work, side-by-side. Now the problem is, I'm connected to a wireless router, but the wireless only works on one of the laptops. So I'm stuck with one laptop that has no access to the internet. Both machines do, however, have working ethernet nic cards. So, I was wondering if I could use the laptop with the wireless connection to share the internet connection with my other linux machine and access the internet on both of them. Or as an alternative, just use the internet on the machine without wireless and be able to switch back and forth, that would increase my productivity like 30 fold.
View 5 Replies View RelatedI am running FC13 on a Compaq Presario 2100 using a Broadcom BCM4306. I was able to get it running thanks to Fedora Unity Project. But It's a very unstable connection. I don't know what settings to adjust or enable or disable. It's not my router, this is the only wireless connection in the house that I have trouble with.
View 1 Replies View RelatedI am running Ubuntu 10.10, and I would like to use my computer to share the internet connection from an ethernet port. For example, I would like to set up my computer as a wireless access point so I can create a network that other computers can connect to for internet.
View 3 Replies View RelatedIn Gnome, I can get my wireless connection working no problem. However, my work PC uses KDE and I'm kind of used to it now, so I've installed KDE on to my Fedora system (v11, 64-bit). I cannot get a wireless connection with KDE at all.
As an aside, Gnome manages my dual monitor set-up just fine, whilst KDE doesn't - it gives me the same display on both screens.
why what is effectively a different front-end should make such a difference to the internal programs - a bit like respraying your car from red to blue and then finding out you need to change the engine as well.
Today installed Ubuntu 10.04. The problem is that I cannot connect to the internet, which was no problem with the previous version (9.10). I use WiFi for my internet connection. My network is shown in Ubuntu. However Ubuntu cannot connect to my network. After some time trying it says : wireless network disconnected
View 9 Replies View RelatedI have recently installed Ubuntu V9.04 onto my the old (fatter) PS3 and I am trying to connect to my wireless home connection. But upon click the connection icon on the task bar, Wired network and wireless networks are grayed out from the options and the network connections box does not detect anything, not even my neighbors Wifi!
View 1 Replies View RelatedI used to be able to connect to the net using my laptop {Ubuntu 9.10 on Compaq nx7400.}by means of wi-fi . I do not know what I have done but I lost the facility to connect to the net.I noticed the Network Manager disappeared from the notification area. I manged to put it back. It detects the signal from the router and after entering my password it displays Connection Established but I still cannot access the net and does not load any web pages. I have the same Ubuntu 9.10 Desk on a memory stick, when I use it on the laptop it works fine.
I enclose a screenshot of iwconfig.I did sudo lshw -C network and it shows DISABLED. How do I enable it ? Are there any other info that I should supply and what and how.
My icon shows that the connection is good using wifi . However, I could not go online. What's wrong ?
View 10 Replies View RelatedMy Fedora 10 install runs from a single PC, from a single location. I'd like the connection, via wireless, to automatically connect to my home network. Right now, I suspect that NetManager scans all the options first.But that's a waste of time. How do I set things up to skip all that and just grab the only connection that will work?I have NetManager set up to "Auto linksys" with MTU set for "automatic" too. I've Googled around for this, but maybe have missed something. Too often, at login I do NOT connect though the network is available. I suspect there's a way to lock this in that I have not yet discovered...
View 1 Replies View RelatedI have fedora12 installed on my old laptop. I would like to use it as a wireless router so that I can use my new laptop without wires. The old laptop will be wired connected to the internet. I have already tried creating a wireless ad-hoc connection with the Network Manager and I manage to connect to the internet with my new laptop but only if I don't use any protection. If I want that connection to use WPA or WEP-128 it doesn't work!
View 10 Replies View RelatedI decided to give linux a try on an old laptop I had at my house. It's a Dell Inspiron (don't remember the model, will update as soon as I get home). Installation was flawless and extremely fast, but I cannot connect to my house's wireless network. I had exactly the same problem with Ubuntu, which is why I tried Fedora. I had installed Ubuntu over a year back and it had worked flawleslly, but I had to loan the pc to a friend so I reinstalled Windows.
Wireless drivers are Intel PRO/Wireless 2200 which should be included in the kernel. I am a complete Linux/Fedora n00b, just want to start learning.
i just successfully downloaded and installed ubuntu koala (9.10 i think...) and its a great interface. i am just having extreme difficulty trying to set up the wireless connection. when i log back in osx, i am able to access the router and use the internet as i am doing now when i post in the forum. i am just trying to learn how to configure the wireless in ubuntu as well. have someone who has successful been able to connect wirelessly on an imac, or apple laptop in ubuntu.
View 7 Replies View RelatedI need to setting up my wireless connection on ubuntu.
View 1 Replies View RelatedEverything else works fine on Ubuntu 9.10 except when I try to connect to the internet. I have wireless. It just keeps connecting nonstop and never connects. I don't know what to do. Please help me. What should I do? I'm using Acer Aspire 5534 with Windows 7.
View 9 Replies View RelatedI've got my wireless card working fine, the only thing is that I have to enter the following EVERY time I log in:
Code:
sudo iwconfig ra0 essid MYID
What can I do to bypass this step?
I installed Ubuntu and I cant get my wireless connection to work. I found that I need ndiswrapper to update my drivers following the sticky post in here. However there is a problem, because I cant successfully run ndiswrapper on my system.
View 9 Replies View RelatedMy old PC has new life thanks to Ubuntu 9.1. However, a few small problems still remain:
1. D-Link wireless adapter: My wireless connection percentage never seems to get higher than 70%, even though the wireless router is right outside the door. And to top it off, I can see other neighbor's networks and the signal strength is higher! I am running ndiswrapper if that helps, and the connection is WPA/WPA2, speed of 130 Mb/s which is great, but can I improve the signal?
2. If I leave the computer on and come back after a while, the monitor is black, and I can see that the wireless connection is still going, but I can't seem to "wake up" the computer. I have messed with the settings, but have not attempted anything in the terminal. Can someone provide a simple fix? I would like to Suspend or Hibernate, but they don't work (meaning, I can wake up the computer). So I have resorted to simply logging off each time, which works.
3. Watching streaming video using RealPlayer, many times the screen freezes, and I am unable to navigate to anywhere else on the computer. Meaning, the mouse moves, but cannot open, close, change, do anything on the computer. Ctrl-Alt-Dlt doesn't even work to pop up anything. Is there a less abrupt way to Force Quit than holding down the power button on my computer and restarting the whole thing? I am sure that is not too good for the computer.
I had no problems using my dell mini with ubuntu wireless UNTIL i did a direct connect into my home network to download some updates. Now the wireless connection option has disappeared and only shows a wired connection in "network". Does anyone know how to get it changed back. Terminal no longer shows an eth1 but lists eth0 as the wired connection on ifconfig.
View 1 Replies View RelatedHi - I am new to Linux and Ubuntu so I have no idea how to fix or problem solve unfortunately I installed Ubuntu 9.10 from scratch recently on this laptop and all was good. I connected to my WIFI network no problem. It's WPA PSK encrypted, DHCP enabled. I just set it up in Network Manager and it was all fine. Then after a few days I installed a printer and some packages and updates via synaptics. The network connection started dropping after 20 mins or so. Only a reboot would restore it - auto connects at first, runs fine till it drops then never will reconnect. I posted on here, someone gave me some lines to put in a config file. I tried that. I didn't seem to help much, problem remained. Yesterday I checked for updates and there were a whole bunch so I just installed them all. Now I cannot connect at all. I have deleted and recreated the connection in Network Manager but it doesn't help. It tries to establish a connection but never achieves it. I am connecting to the internet now on the same laptop booted into Windows, so all the hardware is fine.
Can anyone who knows about ubuntu networking help? Do I need to do a complete reinstall? Seems a bit much, but it worked when I initially installed the OS. I want to like Ubuntu, but something as basic as connecting to the internet is pretty vital so reluctantly having to start using Windows again...
I have a new Toshiba Satellite L450, and decided to run Ubuntu, which is new to me. I am running a 64 bit Karmic, and there is no driver that works. So, to make a long story short: a friend helped me get a driver on my Desktop, namely: rtl8192se_linux_2.6.0100.1012.2009_64bit.tar.gz We had it working, but when I let in the first large batch up updates, it kicked the driver out. I found instructions, installed it again. I let in the next updates, and it kicked out again, and this time the instructions don't work. So, I have two sets of questions:
1. Will updates always undo my wireless? Are there certain updates I should avoid if I want the wireless to stay up and running? (I just assumed the thing to do is just get the updates -- though I am guilty of having no idea what they were about.)
2. Did the updates cause one of my instrucitons to no longer work, or need to be modified?
They were as follows:
sudo apt-get install build-essential
cd ~/Desktop
sudo tar -xvzf rtl8192se_linux_2.6.0100.1012.2009_64bit.tar.gz
That 'sudo tar -xvzf...' operation is the one that stops me. Is there something to change in that line? It goes on:
cd rtl8192se_linux_2.6.0100.1012.2009_64bit
[Code]...
this worked the first time I tried it. I posted this earlier under 'hardware', and do not know how to get that post off, so I typed it here once I realized.
I have a very strange wireless problem, i have ubuntu 9.10 installed on a dual boot with a belkin pci wireless card, i have used ndiswrapper to install the windows driver, plenty of wireless connections come up, i find my own and try to connect, it asks for the password (i have double checked and this is correct), and then goes to connect, now heres the weird bit, the connection light comes up on the card as though its on the network then after about 1 minute the light goes out and ubuntu tells me it is now off line.
[Code].....
I have a laptop ASUS k50IJ and when i am connected to internet (wireless connection) the connection often brakes so i have to reconnect and sometimes restart a computer so that the connection will work for some time (let's say 30-60 minutes, sometimes less). The connections most oftenly brakes when i download some movies,
View 7 Replies View RelatedSince I've updated from 9.10 to 10.04, I'm having some difficulties to use the internet. Even though I can connect to my home wireless network, the connection is really slow. I've got a Dell Inspiron 1545, and here comes the configuration:
Code:
sussa@sussa-laptop:~$ sudo lshw -C network
[sudo] password for sussa:
*-network
description: Wireless interface
product: Wireless WiFi Link 5100
vendor: Intel Corporation
physical id: 0 .....
Apart from that, I must say that Ubuntu 10.04 is fantastic. Easy to use, elegantly designed and working perfectly on my PC
I just upgraded to 10.04. I had wireless connection for 1 day and now nothing. No ethernet connection either. I CAN use both wireless and ethernet using my machine on Windows.....so the connection stuff does work. Here's the output of of the commands I got from the "sticky". I can't display the output as this forum puts it all together as one continuous sentence with no line break!
View 9 Replies View RelatedNOTE: My upgrade wasn't smooth. Now everything is extremely slow. However if I boot from the disc to try without installing, the connection problem is still there. There is an exclamation mark on the connection applet, right clicking shows that Enable Wireless is unchecked and unclickable. I've included outputs of common network commands which might prove to be useful.
Code:
[~] ifconfig
eth0 Link encap:Ethernet HWaddr 00:1e:33:60:f0:3c
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
[Code]...