I used to be able to connect to the net using my laptop {Ubuntu 9.10 on Compaq nx7400.}by means of wi-fi . I do not know what I have done but I lost the facility to connect to the net.I noticed the Network Manager disappeared from the notification area. I manged to put it back. It detects the signal from the router and after entering my password it displays Connection Established but I still cannot access the net and does not load any web pages. I have the same Ubuntu 9.10 Desk on a memory stick, when I use it on the laptop it works fine.
I enclose a screenshot of iwconfig.I did sudo lshw -C network and it shows DISABLED. How do I enable it ? Are there any other info that I should supply and what and how.
A friend who switched ISP's gave me his old Linksys WRT54-G wireless router. I went through the installation procedure and had a wireless connection up and running - smiley face. I had security set up for WPA, and decided to upgrade it to WPA2. Another smiley face. When I went to connect (had already done so successfully), I noticed it referred to my wireless as Linksys - I was expecting to see the SSID. So I started playing around in Network Manager and now I have things all effed up.
Don't know exactly what I did, but now I have no wireless. So I ran a few commands (lshw -C network, iwconfig, ifconfig, and iwlist scan), and looking at the results I see what appear to be inconsistencies in the output. I've posted them below, and make the following observations:
1. Under the lshw it refers to my wireless connection logical name as wmaster0, and has the correct MAC address, etc.
2. Under the iwconfig it says, 'wmaster0 no wireless extensions', but then refers to wlan0 as the wireless connection (although it does not seem to be running).
3. Under ifconfig I see both a wlan0 and a wlan0:avahi. The wlan0 has no IP, the wlan0:avahi does, but it is incorrect.
I have fedora 10 and am having problems with the wireless access. My computer uses the Realtek Semiconductor Corp. RTL8187B Wireless Adapter. It connects to the network, it gets an ip address and a broadcast address, but it loses connection within 3 min. I'm also new dealing with linux and fedora.
I installed a clean installation of ubuntu 10.04 inside Windows 7 and wireless worked normally in the beginning that I downloaded and installed all the updates "I selected without updating Grub".On the first reboot after updates, the wireless icon disappeared from the panel and could not connect to the internet although the settings in the Networking tools were correct.
I'm running Ubuntu 10.10 netbook edition on a Dell Mini 9 - worked around a few wireless issues on setup and connectivity has been fine, but now I'm suddenly losing wifi when I unplug my AC adapter. It still shows me as connected, but when I try to view web pages in Chromium, it will load pages for a few seconds, and then suddenly cuts out - though it still looks like it's trying to load the page.
It's the same if I boot on battery power - it will keep trying to connect to wifi but won't until I plug in the adapter. I'm assuming this probably has something to do with my power management preferences in battery mode, but I'm still pretty new to Ubuntu, and I'm not sure how to fix this. I've played with the options in power management, but I have a feeling there has to be more. Can anyone help me? This has been really frustrating.
I have an odd problem in that my wireless connection is okay until I close the laptop. When I open it back up, I'm unable to reconnect. This problem first occurred after upgrading to 9.10. I can reconnect after restarting. I tried several things before breaking down and reinstalling 9.04. After installing 9.04, everything works great. Any suggestions on what is going on before I try upgrading to 9.10 again? I have a Dell D600.
Three months ago my daughter went off to college with a new computer. I zapped her old system and successfully installed Ubuntu 9.04 from a CD. Everything worked fine including all the peripherals and the wireless internet connection. I was able to download and update applications without a hitch. Great system and so much cleaner and quicker than Win XP on the old machine. Then the system was shut down and lay idle for three months.When I fired it up a couple of days ago, all seemed normal except I could no longer access the internet even though the wireless network icon showed four or five bars. I first discovered the problem when I tried to update though Update Manager and noticed that 22 identified files could not be fetched. Neither Firefox, Skype nor Goodgle Earth can connect.
The router is a Linksys WRT54G router that connects to the computer through a Linksys WUSB54G USB network adapter. The router serves three other non-Linux computers without a problem, including one using the same model network adapter.I don't have much experience with Ubuntu, but this is some of the information I have been able to generate.
I tried a few of the recommendations found in other sites, but nothing seems to do the job. I am perplexed because everything was great until I shut down the system for three months and then started it up again. I appreciate any assistance and would be happy to provide additional information as requested.
I'm relatively new to Linux. My netbook ran updates yesterday for Ubuntu and now I am unable to reconnect to wireless network connection. I am using WPA2 encrypted security. I am able to connect via wired LAN. Also, when I went to connect using USB mobile connection, I get an error "unable to mount location". I get the same error if I try to connect my external CD drive. I am using Ubuntu 8.04 with Gnome desktop (2.22.3) on a Dell Mini 9.My wireless device is using Broadcom STA Wireless driver for an 802.11 wireless card.
I'm relatively new to Linux.My netbook ran updates yesterday for Ubuntu and now I am unable to reconnect to wireless network connection.I am using WPA2 encrypted security.I am able to connect via wired LAN. Also, when I went to connect using USB mobile connection, I get an error "unable to mount location". I get the same error if I try to connect my external CD drive. I have tried to force mount but no luck.
I just installed ubuntu 10.04 on my laptop. everything was working fine until i installed firestarter. i didnt like it and uninstalled it. when i did that i lost my wireless signal icon at the top of the screen, firefox starts up in offline mode, and limewire says that network connection is lost. i just want it back the way it was before installing firestarter. please help, i dont want to reinstall ubuntu if i dont have to.
recently i have combined 2 machines into 1. after doing this, the ping to the new machine stops, for no apparent reason, and consequently all traffic to/from the machine also stops. when using the two machines individually this never happened.Lastly, if i restart the network, it kills everything (like the network just wont restart - it reaches the last interface and hangs), and if i reboot the machine, it seems to be fine for about 3-4hours.has anyone seen anything like this when connecting a large number of hosts to 1 gateway, using linux as the router?
The connection/network icon that showed next to the clock is gone. i told it to "move", but instead it removed. grrrrr. now when i go to add, i dont see it. same with email.
I have a server which is located in the basement. The server exports a few directories which I mount on my desktop using NFS. From time to time, the connection gets lost. The server is also not always on. I can't change that part, so I worked out a script which notifies me when it's going down, and when it's back up again. It also mounts everything back.However.. As soon as I loose the connection, my desktop seems to be gone. KDE doesn't work, but I can use a few applications like Konsole, google-chrome, firefox, stuff like that. But the plasma-desktop around it hangs.
As soon as the connection gets back again, everything works. I have this issue only when my desktop is running while I loose the connection to the server. If it's down when I start my desktopworks properly. Unless the server comes alive, the nfs directories are mounted and the connection is lost again.I'm not really sure if this is a networking case, it could also be KDE related, but I figured this was the most reasonable place to put my topic in.My hardware:
I initially loaded Fedora 14 onto a Desktop and started to configure it to be a server but as soon as Iso software updates My network connection completely drops.
I am running ubuntu 9.1 on a Dell Dimension 2400. After installing ubuntu on the pc, it was automatically recognizing my router and connecting to the internet fine via ethernet. Then, my roommate unplugged the router and it won't recognize it. I can't access my router settings, and ubuntu is recognizing it as "inactive" but every other computer in the apartment runs fine. My PC uses a broadcom ethernet controller, and my router is a Linksys wireless N.
My ISP pushes software updates occasionally to my router. This also forces the router to restart. When the router restarts, my ubuntu box loses its network connection and does not automatically restore it after the router comes back online.How can I configure ubuntu to restore the connection once it is available again? It happens on my windows workstation...I am using ubuntu on a box with no screen / keyboard / mouse it serves as a fileserver and I remote desktop in. Obviously if the box drops the connection it is a major annoyance. I am using version 9.10
So, when I booted up, the wired connection was automatically detected and in use. Whenever I suspend my computer and then resume it later I lose the wired connection. It is detected (seen) by Networkmanager, but I can never connect. I found a way to restore the connection, but it is manual and I was wondering if I could automate this process every time I resume. Details follow:
I was running 8.04 and my internet (Comcast) comes via a Motorola SB5100 cable modem then into a Netgear router then into my Dell. When I upgraded to 10.04 yesterday, I lost the wired connection. The wireless connection still works fine, but I have not been able to get a wired connection. Also, most online solutions reference the Network Manager, which is nowhere to be found.
Anyone have any solutions? I would be willing to revert to 8.04 if needed, as that worked fine, and obviously I quite regret the upgrade!
After I updated ubuntu 10.04.3 and restarted my PC, something weired happend and my wired connection was completely lost. I tried different things but it seems that I have lost my ethernet connection. I only have ethernet card and the interface was set to eth0 which is not recognized anymore.
The /etc/network/interfaces includes the following commands, which btw I tried to play with a bit by commenting and uncommenting the lines but was not helpful (but this is the original one):
Also in /etc/udev/rules.d I deleted 70-persistent-cd.rules hoping that it would be automatically regenerated but it did not,
We have an Asterisk machine that we suspect periodically loses internet connectivity, causing all calls to drop. First, would this sort of thing be logged anywhere out of the box? I haven't noticed anything in /var/log, but that doesn't mean it's not there. If this is not typically logged, how I might go about logging it? I'm currently running a bash script from cron every 5 or 10 minutes which pings Google and writes success or failure messages to a log file. This works fine for extended outages, but if the internet connection drops and comes back between cron runs, it won't be caught.
All of a sudden without rhyme or reason, My Lucid Lynx install stopped connecting to my network. This was without any intervention from me as I did not modify install or change anything prior to this happening.
What I have gathered so far is that upon initial boot eth0 seems to always be disabled. So I ifconfig eth0 up to bring it back online. All the settings in the network applet seem to be intact for my manual network that has DHCP disabled. Let me re-iterate that these settings worked fine for months then all of a sudden something went belly up. The same machine will connect fine with the same settings from within Win7.
ifconfig command shows both eth0 and the loopback interface but eth0 never manages to secure the 192.168.1.3 address that it should have. ping 192.168.1.1 returns "Network unreachable" so it appears the connection is being cut off at the machine and not the router. I did check to make sure the connection was even recognized and it sees the wired connection going to the router, but nothing else.
/etc/network/interfaces only shows two lines regarding the loopback interface and nothing else; eth0 seems non-existant within this file which I find odd.
I installed Fedora today, and I automatically had internet connection, I never had do configure anything myself. Then, I was playing around with VPN for a good while (trying to set up the VPN connection to my University), and now, I suddenly lost my connection to the internet!
But only Fedora can't connect anymore, the Windows PC has connection as well as my Mac OS X (I dualboot Linux on my MacBook). The Ethernet connection works as well, when I unplug the cable, Fedora gives me a message, but I just don't get into the internet!
Does anyone have an ides what I have to do? I don't know anything about network connections and I'm new to Linux...
I already restarted the Computer, but that didn't work, and Google didn't really held either.
I have had long term access to a networked HP Photosmart printer but now I get the following message:
Unable to open device hp:/net/Photosmart_C5100_series?ip=192.168.0.161.
when trying to access it.The ubuntu desktop is wired to the router as is the printer and another iMac wirelessly can still print to the HP. HPLIP status shows the icon for the printer but with a red x indicating no connection to it.The only recent network change was the removal of another router from our network. (service is DSL via a combo modem/router from service provider which previously was connected to a Dlink router which has now been removed from the chain b/c was redundant to the modem/router)
As I view it, Ubuntu has a great security risk in that it still allows internet access when the VPN connection has been lost, for whatever reason. As it is now, when the VPN connection fails you get bumped back to using your regular IP, and whatever you are doing becomes transparent to anyone watching. This is simply unacceptable for an allegedly secure platform. Does anyone know of a way to fix this with a script/program, or is there a distribution/OS that allows this? Windows re-dials the vpn automatically, but still allows internet access in the mean time.
When there is a power failure at my university for about 30 minute, my computer stays up because of a UPS, but the switch it is connected to via ethernet is reset. After this, my machine loses network connectivity until I manually select the network using nm-applet.
In System -> Preferences -> Network Connections, the network has the "Connect automatically" box checked.
However, in /etc/NetworkManager/nm-system-settings.conf, there is a line that says:
Code: no-auto-default=00:30:48:b0:11:07, and that is the MAC address of the ethernet card.
I installed Lucid a week ago and have been having a blast with it after a two year break from Ubuntu (been using Mandriva). So the other day I went to hibernate the system and it froze. I naturally did a hard reset and when I log back in, no network connection. That is to say, the system tray says it's connected but there is no LAN light on the router or network card. ifconfig shows it's connected too. When I boot into XP (cringes) it works just fine.
No specifics ATM but the card is a D-Link PCI with a Realtek R8***** chipset
I had some problems installing 10.04, which I'm not going into here unless I have to, but it appears to be up and running now except my PC can't access the network, even though it's wired. This is the first time I've tried putting on a new build by myself as my son always used to do it (my PC used to belong to him many years ago, and is old, like me.)
I am a non-techie, have been gratefully using Ubuntu 8.10 for a few years for the basics: email, web, documents, photos. I have somehow lost my internet connection, but strangely my email still works...!?!? My router is showing all the correct green lights, but I cannot get to any url. I am posting this thread via work (windows) pc. I have searched on this forum and in anticipation have done as much homework as possible, see below.I have a Netgear wired router. I cannot find Network manager on the menus and tried this from the terminal:
Code:
network-manager bash: network-manager: command not found networkmanager
I do have a problem with my internet connection at home, I've a Huawei router and ubuntu 10. When I connect to the internet whether wireless or wired I become able to surf the internet for less than 10 min then it cuts off! and to be able to surf it again I need to restart the whole system!
I used this command to restart the networking but in vain Code: sudo /etc/init.d/networking restart
On windows I do not face this problem with the same internet connection. I do not face it either when I'm using my campus wireless connections using ubuntu/windows!, so the problem is related to my home connection+ my OS.
