Networking :: Network Sharing Folder - Shows Me A Blank After A Few Seconds
May 26, 2009
I have windows 2003 server which i stored some important data that the workstation will connect it or access by thru network connection...
My current setup is: i have a linux distro i used mandriva 2009 and i installed samba...if i used windows to browse in network i can see the name of the pc of linux and i can able to access the linux shared folder.
My problem is if the linux try to access the windows 2003 thru network it seems to be nothing happened coz everytime i click the linux network it shows me a blank after a few seconds...
I really dont have idea if there is any requirements for the windows.
I really want to implement the linux workstation but i still have a big problem issue in networking.
View 4 Replies
ADVERTISEMENT
Feb 11, 2011
I messed up my Network Connections when I put a different NIC in my computer. Now I just went back to using the old NIC. It shows up in ifconfig, but the GUI Network Connections is blank. When I manually Add the connection back to the GUI Network Connections, the settings are not reflected when doing ifconfig.For example, I change the IP address for eth0 in GUI Network Connections, save the settings,
View 6 Replies
View Related
Mar 26, 2011
I'm running 64 bit Ubuntu, and on the start-up after I pass the GRUB it goes blank for a minute then briefly shows the splash for 5-10 secs and then jumps to the login screen. Also the screen is offset by about 10-15 pixels but from the login screen onwards it is centred. (It's also like this for if I'm in recovery mode)
How do I fix this and Im wondering if it is a hardware problem?
View 2 Replies
View Related
Jun 3, 2011
It is probably a very easy question, but I could not find the right answer on the net so far. What I am trying to do is to set up a network of machines running Ubuntu 11.04. On of these machines will have a folder that needs to be shared with all the other machines. Eventually, this folder should be mounted at startup on the machines that are accessing over the network.
So, what I tried to do was: sudo mount 192.168.37.202:/home/user1/dir1 /home/user2/dir2 -o username=user1,password=password1
dir1 is the folder on machine 192.168.37.202 that should be shared. This is the response that I get:
mount.nfs: an incorrect mount option was specified
So, what am I doing wrong? Do I have to install anything special?
As I said before, eventually I want to have an automatic mount, so I guess that I have to edit /etc/fstab. What does this entry should look like?
View 3 Replies
View Related
Mar 26, 2011
I have an opensuse machine - 11.4, running KDE as my desktop. My wifes computer is a Windows 7 PC.
I have installed SAMBA and have configured it to load at each boot. I have set the domain name to WORKGROUP as this is domain name my wife has on her pc. I have shared the video folder within Dolphin in KDE. I'm uncertain about the meaning of the netbios setting (despite reading Chapter29.Samba) and whether I should adjust this setting. Basically, I'm able to see my wife's computer name within Linux, though within Windows, I'm unable to see my linux network. Is it due to the settings that I currently have on my linux pc. The documentation that I'm reading so far is confusing for me.
View 5 Replies
View Related
Nov 18, 2010
I have two partitions, both formatted as ext4. One with Ubuntu 10.10 64-bits and the other just for data (formatted as ext4 zero). I wanted to share a folder from this second partition. I followed the instructions on http://tech.mobiletod.com/how-enable...cation-ubuntu/ but there was not any "Windows networks (SMB)" option, only "Unix networks (NFS)".
View 14 Replies
View Related
Jul 14, 2009
I am running OpenSuse 11. It runs Apache webserver and Samba for filesharing. I am also running webmin. Everything works 100%. I have 2 shared folders that can be accessed by everyone. My question is how can I log in to the shared folder from a windows machine when I set the permissions for only a certain user to log in. My system hostname is Linux.site and my user is henk. I am not sure how I need to log in that way. Should the username be Linux.sitehenk ...
View 1 Replies
View Related
Mar 18, 2010
Can I share Folder & Printers on 9.10 Desktop? I want to use that shared folder & printers from windows.
View 1 Replies
View Related
Apr 12, 2010
been looking for a easy way for simple users (newbies) to share folders over the internet with friends. I found almost nothing about it, in both Windows and Ubuntu, as people usually recommend online sharing (as dropbox and Ubuntu One, which is not what I ask for) or ssh, ftp and related, which are usually not trivial to set up for simple user and you need to install a nice GUI for the client.Why isn't there a simple way as a right-click menu option, then choosing some user/password and having it available over some iport? Something like local network file sharing.This seems like an incredible tool to have.
View 1 Replies
View Related
Dec 19, 2010
I install Fedora 11 for file sharing from windows client Win 95/98, Win xp & xp home. I can login from win xp & xp home to access folder but I can't login from win 95/98 to access folder. I got the error message... "The domain password supplied is not correct or access to your logon has been denied". from win 95/98 Desktop computers.
The following are contents of smb.conf
View 3 Replies
View Related
Nov 7, 2009
I know this might seem stupid, but I can't seem to connect my 2 PCs to share a folder (directory)
The both have Fedora 11 and they are connected through a Linksys WRT54G (one on LAN and the other on WiFi)
View 6 Replies
View Related
Sep 4, 2010
I can't share my /var/www folder on this machine - it worked fine on my Desktop, it just asked me to install the samba windows something.
What's going wrong with this.
Here is the error I get after right clicking and going to sharing and trying to share the folder...
Code:
View 5 Replies
View Related
Oct 28, 2010
Well this problem has been here since Lucid. When I start up my computer and select Ubuntu, I get a blinking underscore for about most of the start up time for Ubuntu. Then It quickly shows the nice Ubuntu Loading Screen (Plymouth) for about two seconds, then it gets to the login screen. I am using the Open Source ATI drivers, I believe the open drivers are called "radeon".
View 5 Replies
View Related
Jul 3, 2009
I'm currently on F11, and experienced problems with Network Manager. Whenever I to connect to a network, wired or wireless, it just seems to try to connect, and then after 2-3 seconds, it just reports "Disconnected"..
Then I switched to network, and both wired and wireless works. so I don't think there is any driver or hardware issue...
Does anyone have any idea of this problem? The network manager have worked on the live CD version ( before installed to HD).
View 12 Replies
View Related
Dec 7, 2009
I have a Fedora 12 box, which works absolutely fine in a fastweb wlan. However, if I connect to another wlan where I need to link to a wireless access point cabled to the ISP modem/router, networkmanager shows the connection is ok, but...
1) I only can browse internet (es:www.google.it) for a few seconds after the connection is established, thanfirefox goes "Impossible to reach the server"
2) the same behaviour is confirmed by ping
Code:
[Adriano@localhost ~]$ ping www.google.it
PING www.l.google.com (209.85.135.106) 56(84) bytes of data.
64 bytes from mu-in-f106.1e100.net (209.85.135.106): icmp_seq=1 ttl=49 time=138 ms
64 bytes from mu-in-f106.1e100.net (209.85.135.106): icmp_seq=2 ttl=49 time=127 ms
[code]....
EDIT: There is a win box in the same net that is working fine.I see in the router config that ARP for the working machine is "complete", while for the Fedora one is "incomplete" Nothing changes configuring a static or dynamic IP address for the Fedora box I had a previous Fedora 11 installation on the same machine that now gives troubles, and it worked fine. But I can't tell if it's a software problem because my ISP seems to have telnet-ed the router, changing it's firmware (and maybe it's config). Shame on they.
View 3 Replies
View Related
Jun 7, 2010
Basically upon logging network manager will connect to my network, and most of the time it will only last 20 seconds or so before it disconnects and tries to reconnects, this tends to go on for quite a while. Logging off and logging on over and over worked once, for this post I opened pages between the 15 seconds that i was connected and after 20 minutes it has remained connected (every time it stays connected for longer than 5 minutes it will never disconnect again) I followed the HOWTO thread so forgive me if most of this information is useless
1 ) Machine Brand and Model (Laptop): Asus 52jr is the model number
2 ) Wireless Brand, Model and Wireless Chipset:
03:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01)is what I found from running lspci
3 ) check interface:
Code:
wlan0 Link encap:Ethernet HWaddr 1c:4b:d6:5c:61:8b
inet addr:192.168.1.101 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::1e4b:d6ff:fe5c:618b/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]....
View 8 Replies
View Related
Mar 22, 2010
I shut down my laptop, which is running Ubuntu 9.10, without any problems. When I got home and tried to boot it, it finishes the POST and then I get a blank screen with a cursor for a few seconds. The word "GRUB" then appears in the upper left hand corner and that's it. The system is hung and I have to power off.
I've seen a lot of discussion that 9.10 uses grub2. Any ideas how I get out of this? Do I need to downgrade to legacy grub?
View 1 Replies
View Related
Jul 28, 2009
I am an old Ubuntu user and have just strted running F11 on my iBook. I always run system-config-samba on all my machines including my server and even on my work server which shares with windows, Linux and OSX and have found it to be perfect. I installed it straight away on the new Fedora system but It doesn't seem to be functioning the way i expected it to.
I installed system-config-samba and then set up one share folder "Public" with open read write privileges and then turned off the Fedora Firewall all together. But "public" did not become open until I entered the user password for the fedora machine. But, then I could see all folders on the Fedora machine. Even root on the fedora machine became write-able on the network. This was not the desired effect at all. I am assuming fedora is using a non system-config-samba file share system that I am unfamiliar with. what is it? and how does it work?
View 1 Replies
View Related
May 20, 2011
I have a system running 11.04 and it is dropping packets on the hardwired ethernet interface to other systems on the LAN, only in the inbound direction. It drops packets every 5 seconds. I verified this with iperf. Outbound packets pass with no problems. The network card in this system is a Broadcom Corporation NetXtreme BCM5752
View 9 Replies
View Related
Nov 1, 2010
I have centos 5.3 i got the login screen but after logging shows error as-- your session only last less than 10 seconds . if you have not logged out yourself tyhis could mean that there is some installation problem or that you may out of disk space .try logging with one of fail session.
views details:
There is lot of space in hardisk and tmp.
View 1 Replies
View Related
Jun 19, 2010
I've troubles getting my new Sweex wireless 300N USB adapter to work. Tried searching in several directions (see closed thread). Further investigations shows however it is caused by the NDISGTK wrapper for Windows drivers. Can anyone tell me whether Sweex is shipping a faulty driver (it is the latest available) or it is a fault in ndisgtk? Or maybe I'm doing something stupid myself, which I do not find completely imagenary below some more detailed information on my findings: Started with network off and examined the networkstatus
Quote:
tpeelen@CC-desktop:~$ sudo lshw -C network
*-network DISABLED
description: Ethernet interface
product: RTL8111/8168B PCI Express Gigabit Ethernet controller
[code]....
View 1 Replies
View Related
Jan 8, 2010
I'm encountering a strange problem. I need to open and forward all UDP and TCP ports related to VoIPtelephony (5000:32000) in the Suse 11.1 server that's acting as router/firewall in our setup. The ports must redirect to a Asterisk server in the local network. (This server has the IP adress 192.168.0.3)I've opened ports in Yast (Firewall>Ports>Advanced) and putted in some masquerading rulesirewall>Masquerading):0/0,192.168.0.3,tcp,5000:31000,5000:310000/0,192.168.0.3,udp,5000:31000,5000:31000when I do a nmap localhost I get:Starting Nmap 4.75 at 2010-01-08 16:52 CETInteresting ports on localhost (127.0.0.1):
Not shown: 991 closed ports
PORT STATE SERVICE
21/tcp open ftp
[code]....
View 9 Replies
View Related
May 8, 2010
OS: Ubuntu 9.10 Karmic Koala
Programs: Network Manager, Ndiswrapper, Device Manager, Terminal
USB Adapter: Linksys WUSB11 v2.8 Driver 4.10
Router: Linksys Wireless-G 2.4ghz
SSID: Doss
Security: Unprotected
Mac Address: Disabled
Whenever i use to type in lshw -c network it used to show details about stuff, but now when i do it it shows nothing.
Also i did whatever was in this thread
how to install windows wireless drivers
i restarted my pc and now i cant even see the wireless network! it doesnt even say enable wireless networking in the network manager!
View 9 Replies
View Related
Sep 16, 2010
I'd like your input on this. A toshiba laptop screen goes blank after few seconds(from turning on).
At first i thought it was fan that was out and once it got hot enough it cut the laptop off like my old Acer did.
But after close examination i noticed that it continues working. HD still spining and fan blows..
Example: Turn on>Hit F2 to go in to Bios> Bios screen appears>Before i have a chance to do anything it geos blank but continues working> I hit Cntrl ALt Del> it resets and screen comes right back up>second later it goes blank again.
ALSO the toshiba logo and whole screen seems to have a red tint to it.
I also get a media test error but that is likely from hard drive not being there during some of the tests.
DO you think it can be an LCD Backlight issue? or possibly video card?
View 5 Replies
View Related
Jan 6, 2011
i have a printer which is shared across the network. All the computers have ubuntu installed. I want that some computers should not be allowed to use this printer.
View 8 Replies
View Related
Mar 28, 2011
I seem to be having difficulties sharing a CDROM... Here is where I am at: My smb.conf section looks like this
Code:
[cdrom]
comment = Samba server's CD-ROM
read only = yes
locking = no
[code]....
My fstab looks like this, (as directed in smb.conf)
Code:
# <file system> <mount point> <type> <options> <dump> <pass>
proc /proc proc defaults 0 0
# / was on /dev/sda1 during installation
[code]....
I am trying to read the CDROM with a Windows 7 netbook.My mount folder has the following permissions:
Code:
dr-xr-xr-x 1 root root 2048 2007-10-10 01:00 samba
View 2 Replies
View Related
Feb 14, 2011
At the outset I would like to tell everyone that I am still relatively a newbie in linux. I use a usb mobile broadband data card to connect to the internet, and I recently purchased another desktop for my wife. Both of us do not share any files, but I do not have a router and was wondering if I could share my connection with her using a crossover cable.I did a lot of Googling around and tried various different things, I even followed another thread in the same forum but the most that I have got is my network manager saying that connection has been established. I am however not able to see her computer under my windows network and don't know how to proceed.I don't know where I am going wrong, and considering that my knowledge of networking is at below basement level, I would really appreciate any help in this regard.
View 2 Replies
View Related
Nov 27, 2009
I'm having trouble getting this wireless card to work. I installed the broadcom-wl driver on Fedora 12.
Code:
[xxx@localhost ~]$ uname -r
2.6.31.6-145.fc12.x86_64
[xxx@localhost ~]$ lsmod | grep wl
wl 1278432 0
lib80211 6436 2 lib80211_crypt_tkip,wl
The card is recognized by System--admin--network as the correct card (BCM43XG) and assigned eth1. However, NetworkManager shows no wireless network. I have a great signal on the same machine if I boot into a Windows partition.
View 4 Replies
View Related
Mar 3, 2010
[Ubuntu 9.10]
I was using my usb Alfa AWUS036H-v5 usb wifi card, and then after I rebooted, it randomly stopped working.. did some searching on the site, one idea was to do
Code:
sudo lshw -C network
which I did, and it shows my internal wifi card (iwl3945) working fine, but says my wlan7 (Alfa usb) as:
network* Disabled
Also, in the upper right hand corner, the antenna is greyed out and says "Device Not Ready"
View 2 Replies
View Related
Oct 26, 2010
I havea tv show burnt to DVD-r using the Panasonic DMR-E50. Now I would like to play it on my pc. However, it is only recognised as a blank disc. Can you think of anything I can try to move this project along?
View 5 Replies
View Related
