Networking :: NFS Connection With Varying UID?
Jan 23, 2011
I occasionally need to connect my laptop to different networks. I have an account on each of the machines, but as they are not coordinated, the UID of my account is different on each machine. Example
Machine.........Account UID
Laptop..............501
Server 1............526
Server 2............517
When I connect to the server, I need to have access to my files and directories present on both that server and my laptop - both read and write. There is no problem getting exports setup, but how to I setup my connections such that I connect using the proper UID - or is there another mechanism to do this?I haven't done that much work with NFS, but I'm assuming this has to have been done
View 3 Replies
ADVERTISEMENT
May 26, 2010
I have just installed ubuntu 10 on a thinkpad t410. At first everything worked swimmingly, INCLUDING the wireless. After about five minutes, the wireless stopped working, in that it seemed to think it was still connected but pinging didn't work. I've now restarted several times, and each time I restart, the wireless works for about 1 minute, then stops working. If I try to disconnect and reconnect it will not reconnect (until I restart, that is).
iwconfig shows the correct ESSID and ifconfig shows an address, and "connection information" shows a varying percentage of connection.
View 1 Replies
View Related
Jul 29, 2011
Awk varying patterns to different file?
[Code]...
What I want to do is when the records have identical $3 i.e. same gene:blabla, I want to put them in a file with $3.out (P.S. along with the lines below it) I tried grepping out $3 first separately onto a file, and then taking each line in that file as a pattern and pulling out records using awk. Somehow I faced probs with pulling out onto $3.out
View 6 Replies
View Related
Apr 11, 2011
I have a file that goes like this:
I need to grep the lines between pattern 1 and pattern 2 and not the lines following pattern 2. Cannot use grep -A(num), as there are varying number of lines following pattern 1. Also, used awk one-liners, but results are erroneous.
View 14 Replies
View Related
Sep 6, 2010
I noticed that one DVD I encoded to ogg (vorbis) resulted in files with varying volume levels (some files have sound much softer than others... and the original DVD is not like that). I wonder if it's mplayer or oggenc's fault. I do it like this (suppose):
Code:
for i in 01 02 03 04 05 ; do mplayer-vc null -vo null -ao pcm:filename=$i.wav dvd:// -title $i-$i; oggenc $i.wav $i.ogg; rm $i.wav; done
I'm doing it by memory so I could have a mistkate or two in the sequence of commands but the idea is very simple
- Output the sound to a wav file using mplayer
- Encode it with oggenc
- Delete the wav file.
Why is the result having varying volume levels?
View 1 Replies
View Related
Apr 3, 2011
I'm trying to create a PAN (Personal Area Network) using a laptop (Siragon ML-1040) and my desktop computer, but I get the Connection Refused (111) error.
Blueman doesn't detect any network service between the two computers unless I start PAND on one of them and then it detects the NAP service. That, only after I enable the NAP/Workgroup services on the Services submenu in Blueman. However, it doesn't work neither with the NM plugins or without them (dhclient and that other one I can't remember the name of).
Any clues over here? I'm using pand 4.91 and blueman.
View 3 Replies
View Related
Jan 24, 2010
Its a case of ".... wireless network connection active but still not internet connection .."I am using WEP - 128 key ... Works when I connect directly using ethernet cable ... but not wireless (pci and wireless router)
ubuadmin@ubucomputer:~$ ifconfig
wlan0 Link encap:Ethernet HWaddr 00:06:25:12:83:3b
inet addr:192.168.1.10 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::206:25ff:fe12:833b/64 Scope:Link[code].....
View 5 Replies
View Related
Jun 21, 2009
I have installed Fedora 11 recently. I want to share my Internet connection.
I have e LAN connection eth0 which is connected to internet.
I have a Wireless connection wlan0.
I want to share my internet connection with wireless connection.
View 3 Replies
View Related
Jul 28, 2010
I'm trying to do a SSH connection between my home and work PC both machines are running ubuntu 10.04. I have read all the comunity documentation at [URL] from Work PC. I went on to the web site what is my ip address and noted down the number, From Home i opened a terminal and typed: pnig (ip address). to which their was no reply, now i'm assuming i need to configure the works router to except connection requests, is this Correct?
Also what information do i need from my works network and how do i get it? I understand that I need the routers expernal ip address, but how do i referiance a specified computer after that address? What program do i use in ubunu and how is that information applied to it?
View 4 Replies
View Related
Jun 11, 2011
My problem is exactly the same as [URL]
but I am stuck at the last hurdle
here are the output of the command that helped to solve the case in the previous post:
ifconfig wlan0
wlan0 Link encap:Ethernet HWaddr 00:1b:77:d2:59:55
inet6 addr: fe80::21b:77ff:fed2:5955/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
[Code].....
I have also tried sudo dhclient but it hasn't helped and I am still unable to connect to the internet
View 1 Replies
View Related
May 13, 2011
When I have video running and the video stops, I see that the connection is destroyed in about 5 seconds, which is what I want. If, rather than stopping the video, I pull the plug, I have seen it take 350 and 380 seconds before the connection is destroyed. Why is there such a large difference in the time to destroy a video connection between stopping the video and pulling the plug on it when using net filter connection tracking? How can I shorten the time for the connection to get destroyed when pulling the plug?
View 3 Replies
View Related
Feb 4, 2010
I have two linux laptops. Currently, I'm using both of them at work, side-by-side. Now the problem is, I'm connected to a wireless router, but the wireless only works on one of the laptops. So I'm stuck with one laptop that has no access to the internet. Both machines do, however, have working ethernet nic cards. So, I was wondering if I could use the laptop with the wireless connection to share the internet connection with my other linux machine and access the internet on both of them. Or as an alternative, just use the internet on the machine without wireless and be able to switch back and forth, that would increase my productivity like 30 fold.
View 5 Replies
View Related
Apr 23, 2010
I'm trying to setup PPPoE connection to establish my DSL connection, but I got
Code:
pppoe[3885]: read (asyncReadFromPPP): Session 4479: Input/output error
pppd[4104]: Cannot determine ethernet address for proxy ARP
in my sylog file.
When I do pppoe-start, it connected but I cannot ping into any destination (even to my modem in the same network). DNS servers are explicitly set in pppoe.conf and resolv.conf. Did I miss anything?
View 2 Replies
View Related
May 8, 2010
I have problem in making connection to my vpn server I can make connection from windows xp to that but can not open any website and I can not ping 172.16.10.1 when connection established.
These are my configuration files:
server config file:
Quote:
client configuration file:
Quote:
And this is my server syslog tailed file:
Quote:
And I added this routing to /etc/rc.d:
Quote:
And this is my iptable:
Quote:
And vpn connection is lost after establishing a lot.
View 4 Replies
View Related
Mar 26, 2010
I connect to my work with GRDC through a VPN. All worked fine until yesterday. IT is now very slow. Could this have anything to do with the fact that Update Manager was only able to do a partial upgrade?
I use Ubuntu 9.10 I tried the RDC on a Win XP machine and the speed is normal, so I don't think the Remote Desktop Server is the problem. Is there a way to test thespeed of the VPN connection or the RDC connection?
View 3 Replies
View Related
Feb 9, 2010
I have 2 computer: 1 computer install ubuntu v9.10, in this computer already installed openssh-server and openssh-client, and 1 computer install windows. In computer with windows , i used putty connect to computer with ubuntu, but i can't connect. I don't understand what's error.
In the Putty , i configured:
IP : IP address of computer Ubuntu.
Port 22
Connection Type SSH
This is error: "Network Error: Software caused connection abort"
In computer with windows, i can ping computer with ubuntu and in computer with ubuntu i can ping computer with windows.
View 5 Replies
View Related
Oct 31, 2010
I have the "Work Offline" problem: when I boot up, the icon on the toolbar tells me I have "No network connection". This is not quite true, since I can access the first page of any website - only subsequent pages are inaccessible. I get a message saying that Firefox is offline. However, when I uncheck "Work Offline" in the File menu, it makes no difference to this behavior.
The problem is on my Ubuntu Dell desktop, which is connected to the internet with cable broadband via a D-Link router (wired connection). It has worked fine up till now. I use Ubuntu 10.04 and Firefox 3.6.11. I am writing this on my Ubuntu Dell laptop which is wired to the same router, so I assume the problem is not the router. I have tried various strategies suggested in threads on these forums, including editing about:config, changing "allow" to "deny" in some lines of /etc/dbus-1/system.d/NetworkManager.conf and changing from Automatic (DHCP) to Automatic (DHCP) Addresses only, but no luck so far. The contents of ifconfig are:
eth0
Link encap:Ethernet HWaddr 001:aa0:91:a7:51
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets: 0 errors: 0 dropped: 0 overruns: 0 carrier: 0
collisons: 0 txqueulen: 1000
RX bytes: 0 (0.0 B) TX bytes: 0 (0.0 B)
[Code]...
If I comment out "auto eth0" as well, it makes no difference. If I uncomment both lines ("auto eth0" and "iface eth0 inet dhcp") then I lose the internet connection altogether.
View 4 Replies
View Related
Apr 6, 2010
i m using RHEL5 on my server machine and open suse 10 on my client machine.both system ping each other, firewall is off of my server machine,i put a file from my client to my server machine using scp command but ftp command is not working when i want to open connection i receive a message "connection refused".what can be the issue?
View 5 Replies
View Related
Jan 9, 2011
I am running Ubuntu 10.10, and I would like to use my computer to share the internet connection from an ethernet port. For example, I would like to set up my computer as a wireless access point so I can create a network that other computers can connect to for internet.
View 3 Replies
View Related
Jul 9, 2010
I need to setup an Ubuntu Server to handle backups over the network (probably rsync over ssh). That server will then transfer the backup data offsite over a secondary external data line.How can I configure the ethernet interfaces to handle such a scenario?
View 1 Replies
View Related
Jan 16, 2011
I just want to use Internet Connection Sharing (ICS) to connect to the internet. I have done a massive amount of troubleshooting, but some of it seems to contradict itself, and the only two things that I know for sure are that it used to work, and that my Ethernet cable is not the problem. When I use Terminal utilities like ifup and dhclient it seems that it can not determine IP information, but when I try to put it in manually, the "Apply" button grays out right after I finish typing it in. When I try to connect normally, in KDE or GNOME, the icon acts like it's connecting, then instead of having the connected icon, I receive a notification that "the network has been disconnected", and it goes back to the disconnected icon.
Oh, and by the way, I know that I could probably find a workaround, but I have limited resources, and this used to work. The Linux is a Dell desktop with Fedora 12 and the Windows is a Windows 7 HP laptop.EDIT: I hope that I didn't mess something up, but I accidentally used system-network-config to try putting in the IP address there, and ended up changing it back to the original settings, but the computer is now calling it Auto Ethernet in the taskbar icon, although sudo iwconfig in the terminal still calls it eth0.
View 7 Replies
View Related
Mar 6, 2010
I have installed fedora 12 recently. after installation i tried to connect to the internet using BSNL broadband connection. I filled in the details such as IP, Netmask, Gateway and even DNS servers. In the services also I ensured that the network manager services is on. However even though my computer cannot connect to the internet. I then tried the ping test of the modem from the address 192.168.1.1 and found that the ping test is successful. Then i tried the network administrator and there I noticed something unusual.
There are two options in the devices eth0 and eth1 thats ok but the unusual; thing is that the Activate (green button), Deactivate (red button) and even the delete buttons are in the background and I cannot select them. Isthis the problem for the network connectivity.
[Code]....
I then tried the ping test of the modem from the address 192.168.1.1 and found that the ping test is successful. Then i tried the network administrator and there I noticed something unusual. There are two options in the devices eth0 and eth1 thats ok but the unusual; thing is that the Activate (green button), Deactivate (red button) and even the delete buttons are in the background and I cannot select them. Isthis the problem for the network connectivity.
View 3 Replies
View Related
Jun 1, 2011
I just installed Ubuntu 11.04 desktop on my desktop in dual boot with Windows 7.
Heres my problem, I am unable to connect to the Internet even though my wired Ethernet connection says it is connected normally. The wierd thing about this is that I also have a wireless card in my desktop and when I connect through that I am able to connect to the Internet. I am connecting to a router that is functioning as a repeater to my main router/cable modem. I have tried to solve this myself but am having no luck. Ironically, earlier today suddenly my ethernet connection worked for a few minutes without me modifying anything.
The output of some terminal commands are below.
Quote:
Quote:
Quote:
However a pint to that ip address (my router) is successful.
Quote:
Hosts.allow and hosts.deny are both fine (not blank but no entries)
View 1 Replies
View Related
Jul 26, 2010
my netbook shares it's wireless connection to my desktop. i've done this through the gui (edit connections > eth0 > ipv4 settings > shared to others) and it has worked for the last i don't know how many months.recently it had become a bit touchy with regards to how it was set up. it didn't work unless the netbook was already booted and wired in at the time of booting the desktop.now however it's gotten even worse and all i get when i connect them together is
"connection established" *pause* "disconnected" *pause* "connection established" *pause* "disconnected" *pause* "connection established" *pause* "disconnected" *pause* "connection established" *pause* "disconnected" *pause* "connection established" *pause* "disconnected" *pause* "connection established" *pause* "disconnected" *pause* "connection established" *pause* "disconnected" *pause* "connection established" *pause* "disconnected" and so on.
View 2 Replies
View Related
Aug 15, 2010
My F12 setup drops the network connection once or twice a day.
If I right-click on the tray icon and pick eth0 it comes right back.
Some relevant lines from /var/log/messages:
Code:
View 1 Replies
View Related
Mar 2, 2011
I have installed qemu/kvm and created a Bridged network connection which works just fine(Windows 7 VM won't work in NAT mode.)
But when I try to use NetworkManager it says that I have no network connection because the network isn't managed, (I set the settings in ifcfg-br0 and ifcfg-eth0 to be managed)
The real problem is that now I can't use my VPN connections (I have many) in NetworkManager.
Is there a way to have both of these pieces of functionality?
I am using FC14
View 5 Replies
View Related
Sep 29, 2010
I installed F13 on a server with dual NICs. I configured both NICs into bonding lacp mode. I also removed the NetworkManager.
Everything seems to work fine, except I cannot connect to internet. I can connect to and from another machine through ssh. I have another server with the same type of networking configuration in FreeBSD working fine. The server is connected to a lacp supporting gigabit ethernet switch. The switch is connected to a router which goes to the modem.
View 1 Replies
View Related
May 18, 2010
I'm writing from italy and I need your help. I installed Ubuntu 10.4 3 days ago and when I open the firefox page this can't be loaded, even if I war connected whit the ethernet cable. So I follow all the sequence of information after i digit "pppoeconf" in the terminal. At the end the system says that the connection was establieshed, so I restart the computer and when he was loaded again... well...the network manager in the upper-panel near the volume control was disappeared! i create a new wired connection giving him a manual ip, subnet mask and gateway. I tick the option connect automatically, but the computer remain unconnected.
View 4 Replies
View Related
Oct 1, 2010
Is it possible to configure ubuntu in a way to connect to a specified VPN connection on startup? The system should only use this one VPN and never any other connection.
View 1 Replies
View Related
Nov 25, 2010
How to connect net in 9.10? modem:Hauwei SmartAX MT880
broadband: Bsnl
View 2 Replies
View Related
