When I boot, I can grub into linux, but when I try to boot windows it doesn't work.
It shows a screen where it lists the commands:
However, if I change the harddrive boot order in bios I can easily get back into windows by selecting that harddrive for the first slot.
However, I don't want to do this everytime I want to switch operating systems.
I'm having some issues getting Ubuntu to boot. I've installed it a bunch of times before, but dual booting and not. Right now though, I'm having issues installing it along with Windows 7, on separate hard drives. Here's my current configuration:
60GB SSD with windows 7
500GB HDD, NTFS, windows 7 data
I bought a 1TB HDD that I want Ubuntu on, but I only want Ubuntu to use 100 GB. I want the other 900GB for Windows 7. So, I put in the Ubuntu CD, chose to edit the partitions manually in the 1TB HDD, created a 100GB ext4 primary partition for linux and a 2GB swap partition, leaving the other 900GB unallocated. Ubuntu seemed to install fine, said it succeeded, and asked me to reboot. When I did, however, my computer boots straight into Windows (no GRUB screen at all). I've tried changing the boot priority to all three of my installed drives from BIOS and tried putting GRUB on both my SSD and 1TB HDD.
I just upgraded from 9.04 to 9.10 (using Update Manager) in an attempt to get to 10.04. Installation and upgrade seemed to go OK until reboot. Now I only get a black screen - I don't see the grub menu, I don't even see any way to access the BIOS menu- not even a blinking cursor. I can hear it start and I can see the numlocks key go on. Ctrl-Alt-PrtScrn-B does not reboot (nor does Ctrl-Alt-Backspace- but I didn't expect that would) Surprisingly Ctrl-Alt-Del does (or at least it sounds like it does) reboot the system. I do have a NVIDIA cards and after reading around I suspect that this is likely the problem but I have no idea what to do now..
Here's what I've attempted:
I figured since I wanted to get to 10.04 anyway and this was so troublesome I could just go do a fresh install with a Live CD or USB to 10.04. However, even with a live CD or USB I still just get a blank screen.
Continually holding down F2 (and other function keys to try to access Bios)
Holding down Shift while booting
Esc while booting
Moving the monitor to the VGA port (as opposed to the NVIDIA card).
Other information...
Previously I had tried to upgrade to 9.10, but ran into problems with it not recognizing my RAID, so I just found it easier to go back to 9.04. (So although this is likely a graphics problem I guess the possibility is that now it doesn't even see my boot drive- although- if that was the case, I'd assume I wouldn't have the same problems from the CD or USB boot.) My ultimate goal is to get this to 10.04, if I could do it with an upgrade instead of a fresh install I'd prefer that, but at this point just getting back to a functioning computer would be ideal. I see many options in other posts for how to get back once you can access a command line- but since I can't even see that, I'm not sure what to do now.
I have an old computer, it came with Windows 98, later I updated it with Windows XP. XP ran slowly because of it's outdated hardware. Around this time I already had a new computer. I decided to install Ubuntu on it to muck around with. However, Ubuntu also runs slowly and I have a dual-booting computer. However, when I try to get into the BIOS of the computer and run the 98 disk, I can hit every button and BIOS will not load. Question: How do I reinstall Windows if I can't access the BIOS?
View 9 Replies View RelatedI have a Dell Vostro with sda and sdb (the latter was installed by myself). I installed FC14 x86 64 onto sdb with /boot being on /dev/sdb8
I did not want to install grub onto /dev/sda as this is a shared machine. I thought that I would be able to use the BIOS's 'select boot device' to select the sdb disk and boot off that and get into FC that way.
fdisk verifies that /dev/sdb8 is marked as bootable and grub (via find /grub/stage1) confirms that it is installed on hd1,7 (ie /dev/sdb8)
However, no matter which hd is choosen as the boot device, Windows is always booted - I change the boot order to use: DVD, sdb, sda but it still boots Windows. It seems like the BIOS only wants to boot sda no matter what.
I have had Fedora 14 running well on my Dell Latitude XT. All was good until I created an NTFS partition and attempted to install windows XP on it. The installation failed, then when the computer boots i get:
"Error Loading Operating System"
I have attempted the following:
1) FedoraLive from USB then :
Code:
[root@localhost liveuser]# grub-install /dev/sda
Probing devices to guess BIOS drives. This may take a long time.
/dev/mapper/../dm-0 does not have any corresponding BIOS drive.
2) I tried:
Code:
# grub-install --recheck /dev/sda
Probing devices to guess BIOS drives. This may take a long time.
/dev/mapper/../dm-0 does not have any corresponding BIOS drive.
installed windows 7..then tried restoring grub using live cd....mounted partition somewhere else....then installed ubuntu again where it was installed previously and now grub is not detecting windows 7 but i am able use my windows files
used sudo update-grub2.
I do not know what to do, i cannot load windows partition. it just loads grub again. this must have been something that happened when i upgraded to the 10.04 or w/e. can someoen help me out with what i can do to stop this or fix it. maybe i can reinstall but i want to know what will work first, i do not have a lot of time to fool with my computer like this again. i spent a week getting ubuntu on my computer the first time so i do not ever want to spend that much time again especially in finals week. !
View 1 Replies View RelatedI am actually facing a vague problem here. I was previously running Windows XP and Ubuntu . Ubuntu was installed Windows XP The problem is
1. First I tried to do some disk partitioning. That ended up with some error.
2. Ignoring that, I went to install Windows 7 over Windows XP but I was not able to proceed with Windows 7 , because the partitions were corrupted.
3. So I used Ubuntu LIVE CD (Grub was lost at this point )and used 'testdisk' and recovered the partitions.
4. Now installed the Windows 7 successfully.
5. Now again I moved to Ubuntu Live CD to write the GRUB. After which I tried restarting
6. Now Ubuntu is booting perfectly as before. But the problem is with Windows
7. The GRUB loader instead of showing Windows 7, it shows Windows XP !!! . and there is no other entry for windows. When I tried opening it, it says "error, cant read file" and further inout moves back to the grub loader list again.
"How do I change the entry to Windows 7 from Windows XP and boot Windows7 successfully " I tried it a couple of times, same thing happens . So how to change the entry?
I had 9.10 installed and I did an upgrade to 10.04. However I cannot see anymore my Windows Vista partition with grub.. I have a Toshiba laptop Satellite p305.This is my boot script output:
Boot Info Script 0.55 dated February 15th, 2010
============================= Boot Info Summary: ==============================
=> Grub 2 is installed in the MBR of /dev/sda and looks on the same drive in [code].......
how to be able to add windows 7 to my grub menu or to even be able to boot to windows 7. I am currently unable to do it and my system just automatically goes straight to ubuntu. I've tried holding down SHIFT during startup and all that appears in my list is ubuntu entries and a memtest entry. My windows 7 files are still intact because I can see the drive through ubuntu and see all my files. I am trying to have Windows 7 on one hard disk that is 640GB and ubuntu on a second hard disk that is 160GB
[Code]...
Ive been running windows 7/Ubuntu dualboot for some years now and never had any problems.Some months ago I got a new Patriot Inferno ssd. Ofc the first thing I did was to installl windows 7, it had no problems, ran fast and smooth. Then when I reinstalled grub I started to get error when trying to start windows, the logo never apeared and all I got was the message "Windows failed to start. A recent hardware or software"Status: 0x00.00F" "Info: The boot selection failed because a required device was inaccessible.". It does not matter what order I install windows and ubuntu in, or how many times Ive tried to reinstall grub. Windows 7 will not work while I have grub/windows installed. Right now Ive got them installed on separate drives, ubuntu on the ssd and windows on a partition on a 1tb hdd. Unfortunately I need to have windows for .net programing and gaming..
[Code]...
I am planning to use EFI BIOS in my system with GRUB as the boot loader. Is it possible to use Grub loader with EFI BIOS?? If yes, whether Grub needs to be EFI compliant to use with EFI BIOS??
View 1 Replies View RelatedI'm dual booting Win7 & Ubuntu 10.04 on a Gateway NV78 series laptop, and while on the Windows side, the Gateway Update Manager asks to update my BIOS. If I allow it to do so, will it mess up Grub? For bonus points: how could I fix Grub if the BIOS updates does damage it?
View 6 Replies View RelatedIs it possible that grub can load usb driver because BIOS of my computer is 10 or more years older. Currently in grub if I run
root (<press tab>
I get
fd0 hd0
meaning so far floppy & hard disk can be accessed. I am using ubuntu 8.04 .
I was installing Ubuntu 9.04 64bit server from the CD on a machine that I normally run ESXi on. I wanted to test disk speed on a direct install vs. the install in ESXi, so I installed a 4th hard disk, shutdown ESXi, and installed Ubuntu directly on the new disk (4th Bios disk - SCSI:3 or sdd). When I tried to boot from this disk, nothing happened. I rebooted from the ESXi install disk (SCSI:2 or sdc), all was fine. Playing around, I finally found that to boot the ubuntu install, i had to boot from SCSI:0 - Grub had installed there, even though I never indicated that disk for anything during the install. It would be much better if Grub ASKED where it should be install, rather than assuming.
View 3 Replies View RelatedMy problem, GRUB loader appears when it normally did not and Ubuntu fails to boot. My story, I installed ubuntu on a HP Touchsmart laptop a month ago because I was having troubles with Windows and... well I just wanted to install ubuntu. All goes well until a week ago when my sound was permanently muted through a hardware switch and ubuntu was not detecting it. I tried hitting the button on my laptop but nothing worked. Soo... I tried resetting my BIOS in hopes that it would fix it. I set the bios to its defaults and booted. This is where it got weird. the GRUB loader appeared when it normally did not and upon booting, a black screen with flashing cursor would show up and then... nothing. I changed the bios settings back to what they were and still nothing.
I have removed the silent boot from the GRUB boot line and can see whats going on... a little, the last thing it shows is "Running /scripts/init-bottom ... done." annnd nothing else. When booting in recovery mode it stops after 30 or so seconds on...
Code:
ACPI: Power Button [PWRB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/inp
and just ends on that line. the previous line shows closing the Lid as a button.
I have tried booting into a live USB (as the laptop has no cd drive) and everything works fine.
how the BIOS would be related to GRUB/booting..
Is there some workaround by changing grub settings other than rewiring the hard disks or changing in bios..
1. my bios is getting reset (low battery)
2. my hard disks are sata and ide, so the ide one is loaded as hd1 by default, cudn't find any way to change that..
I have Debian Jessie 8.0 amd-64 installed. It is a dual boot system with Widnows 8.1 alongside. Both the systems work fine with a few glitches coming at times on jessie. But I assume it should get stabilised with time.
Problem is:
The usb keyboard is no longer detected until the GRUB stage crosses.
* This implies I am unable to press F2 to enter into BIOS
* I am unable to chose Windows 8.1 by using arrow key on the keyboard.
When the default system (first in the grub list), in this case Debian is selected after time runs out then the keyboard comes back to life and works properly thereafter.
So far I have tried the possible solution given at [URL] .... but it did not work.
Some Information
================
$ lsb_release -a
No LSB modules are available.
Distributor ID:Debian
Description:Debian GNU/Linux testing (jessie)
Release:testing
Codename:jessie
$ uname -r
3.13-1-amd64
This is partly a note to myself for the future and a guide to anyone who experiences similar issues.
So, I had to reinstall Windows XP since my previous installation gave me a blue screen error due to reasons unfathomable. Naturally, this deleted the GNU Grub and I could not login to my Fedora.
I read that apparently booting from a DVD installation offers an option to enter the rescue mode. I did not have a DVD, I only had the LiveCD so I had to figure out a way to reinstall Grub from the LiveCD. The following method seemed to do the trick.
Run the LiveCD and open Terminal.
1. Find the partition where the Grub Stage1 is code...
i've been using ubuntu with wubi, and I'd like to install it on my new hard drive (so windows is on one hdd and ubuntu is on another). afaik, grub will be installed on the hdd w/ ubuntu, and i have to set it to recognize the other (windows) hdd. assuming that i want to get rid of ubuntu and just use windows, what steps do I have to take to do so? (if grub is only on the ubuntu hdd, then would I just have to format it?)
View 2 Replies View RelatedI installed Puppy Linux on a partition on an older 2000-era computer. The other partition had Windows ME, which crashed and burned recently. Lately, the computer has started to open GRUB very slowly. It is also slow to boot Puppy Linux from there. I reinstalled GRUB, to no avail. I decided that the problem was probably a slow BIOS, but I'm not sure. Does anyone know of another possible problem, or of a good boot-disk BIOS diagnostic tool? I tried using a couple of the tools on the Ultimate Boot Disk, but they all got hung up, displaying: - InitDisk as the last line in the sequence.
View 3 Replies View RelatedI had windows 7 and i installed ubuntu both on primary partitions. They were running normally and the dual boot was working well. After that I installed debian on a third different logical partition of my disk and then only debian was running and windows and ubuntu didn't. Ubuntu does not seem even when the computer starts! Then i reinstalled ubuntu over the debian so i can run only ubuntu. I cannot see windows 7 at all when grub starts
command sudo fdisk -l gives me:
Disk /dev/sda: 320.1 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
[Code]....
Partition table entries are not in disk order
Why i have two * in boot column? I have tried some methods i found on the internet but didn't work.
My laptop got broken so I extracted my hard drive to use as an external. The problem is the computer I am using has windows xp on it and my external has also a windows xp, ubuntu and kubuntu. I need to have the xp from my external running because i use it for .net development. How I can have 2 windows on grub with root (h0,0) and (h1,0). My ubuntu is (h1,6) and kubuntu is (h1,3).
View 2 Replies View RelatedI've been dual booting for years now between XP and Ubuntu Dapper -> My computer has a number of hard drives but on the main Hard Drive I have a Windows 7 partition and a Ubuntu Partition and a Swap partition.I've installed Karmic on it's partition twice now, I know the disc is fine because I have checked it for errors and installed it on other computers.
I have tried setting up the Boot Loader from Windows 7, but this yields a message "Cannot load from harddisk". GRUB doesn't install what so ever.Do I need to specify where GRUB gets installed as Windows 7 uses a different Boot Loader? Is this a Karmic / Windows 7 / Hardware bug?
After I installed lubuntu Windows XP is not showing up as an option in GRUB (boot menu).Only lubuntu and memory test.Windows partition is there and untouched, because when I run G Parted I see it, and it is the same size as before, and still flagged as 'boot'I tried running my XP-OS-CD in repair and the repair CD sees and identifies the Windows OS, and I can gain admin rights, but I don't know the commands (within CD) to repair the boot menu so windows XP is an option when booting up.
View 6 Replies View Relatedfirst i partitioned my hdd into two partitions and then i installed windows 7 on the second partition all went fine so i decided to install Linux on the first partition installation went fine but after that GRUB could not boot windows 7.
Code:
Disk /dev/sda: 203.9 GB, 203928109056 bytes 255 heads, 63 sectors/track, 24792 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x05d67c23 Device Boot Start End Blocks Id System /dev/sda1 1 12748 102398278+ 5 Extended /dev/sda2 12749 18770 48371715 7 HPFS/NTFS /dev/sda5 1 12224 98189217 83 Linux /dev/sda6 12225 12748 4208998+ 82 Linux swap / Solaris
I installed Windows Xp 64bit(in a partition called d:) with dual boot with Debian Wheezy. Installed first Windows Xp and after Debian Wheezy, but grub is not seeing Windows!
Look at my "fdisk -l".
root@robgeek:/home/rob# fdisk -l
Disk /dev/sda: 80.0 GB, 80026361856 bytes
255 heads, 63 sectors/track, 9729 cylinders, total 156301488 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0xe274e274
[Code] ....
i have installed debian but during installation my installed windows 10 was not found by the grubloader. i have installed windows 10 on my ssd and the debian on my hdd. nevertheless i installed the grub loader on the master boot record, because it said i could still configure it so it can boot both the windows and the debian.The debian installation is running fine. But i now want to boot the windows too. The problem is i have never worked with the grub loader yet and i am little scared that i will do something wrong.How can i get grub to load my windows ?
View 9 Replies View RelatedI have windows and I installed fedora 12 on a separate partition.
However, I had a problem with my windows XP SP 3 and had to install windows. Which I did on my C drive. However, when I re-boot I on longer get the GRUB loader displayed so cannot boot into fedora.
Is there anything I can do?