General :: Unable Activating Eth0 ?
Sep 23, 2010My box is centos x86 5.4.
I changed lan card and tried to enable eth0 with command "ifconfig eth0 up", but not worked.
Code:
How to enable eth0 and see "inet4 address".
ADVERTISEMENT
General :: Stop And Restart Ethernet Connection Ubuntu 9.10 - Ignoring Unknown Interface Eth0=eth0
Mar 8, 2010If I uncheck and recheck "Enable Networking" in the Network Manager Applet 0.7.996 I would expect the wired network to disconnect (which it does) and reconnect (which it does NOT). So I tried sudo ifdown eth0 and got
Quote:
Ignoring unknown interface eth0=eth0.
ifconfig tells me
Quote:
eth0 Link encap:Ethernet HWaddr 00:25:64:e8:18:2c
inet addr:192.168.0.112 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::225:64ff:fee8:182c/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]....
so I am at a loss. How do I stop and restart the network interface short of rebooting the machine?
General :: Force Server To Open Connections Via Eth0:0 Not Eth0?
Mar 3, 2010I got two IP's in my dedicated server. Both are external IP's. I would like to make connections using 2nd IP address under eth0:0 interface. For example: when using "lynx whatismyip.com" should display my 2nd IP. How to do this using iptables ?
View 1 Replies View RelatedUbuntu Servers :: 10.10 - Setup Eth0 With Subdevice Eth0.0 And Eth0.99 To Come Up At Boot
Apr 22, 2011im trying to setup eth0 with subdevice eth0.0 and eth0.99 to come up at boot
eth0 is dhcp clint
eth0:0 is static ip
eth0.99 is 802.1q vlan interface
/etc/network/interfaces
Code:
auto lo
[Code]....
General :: Getting Eth0 To Come Up - Eth0 Seems To Have Vanished From Computer
Mar 2, 2011I'm not sure how long ago this happened but eth0 seems to have vanished from my computer. wlan0 works fine and when I plug into the switch there is carrier detect.
Code:
21:35:43 ~:$ ifconfig eth0 up eth0: ERROR while getting interface flags: No such device
21:55:49 ~:$ lspci 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05) 07:00.0 Network controller: Intel Corporation Ultimate N WiFi Link 5300 After that i have no idea where to search for problems next, any ideas would be greatly appriciated (can't spell) ubuntu 10.10
General :: Activating Belkin Usb Wireless F5d7050 ?
Dec 11, 2010Trying to add wireless adapter to my fedora 13 system. Belkin f5d7050 raxwn450th v4000. Located zydas zd1211 driver on source forge. Downloaded and installed it
Code:
showed my dsl wireless adapter
system - preferences - network connections did not show it
I rebooted - now
Code:
shows my dsl adapter, and lsusb says
Code:
But it not show up on system - preferences - network connections
Would have prefered to install it via yum but dont know the magic words to get yum to find it.
General :: Keyboard Activating SHIFT Randomly For A Short Time
Feb 14, 2010I think this might be related to the changes to using udev or DeviceKit. It started when I was running the beta versions of F12. Then it crept into Debian Sid. And my Arch Testing and Gentoo also suffer from the same.
What happens is that I'll be working along. Then when I press any key it is as if the SHIFT key is pressed. When I press CAPSLOCK, some of the keys react as they would normally. This never lasts for more than 5 minutes. And seems to happen infrequently. I say seems because there are the times I am at work and it could be that the same thing is happening only there is no one on the keyboard.
The reason I pick out udev/DeviceKit is that when it used to happen to F12 beta, the other distros had not yet made the move. So back then it was only a F12 issue. Now it is happening across the board. And only started recently.
General :: Activating NVidia Drivers Makes The Desktop Disappear
Aug 6, 2011I have been trying to install Linux on a olsish computer for a long time now, with no luck :[ Everything goes fine until Ubuntu/mint asks me to activate the nvidia drivers. When I do it and restart and login the there is no desktop. The computer has a single core amd athlon 64, 1.5gb's of ram and a nvidia 7300gs card.
View 3 Replies View RelatedUbuntu Networking :: 10.04: Unable To Use Eth0 And Usb0 At The Same Time?
Nov 20, 2010I have no telephone connection at home, so I use my cellphone to connect to the internet. Network manager reports this interface as a "wired connection", usb0, using the cdc_ether driver.I also have a router at home, so I can connect my netbook to my desktop wirelessly. My desktop computer connects to the router via ethernet connection, and network manager reports it as eth0.
When I had Ubuntu 8.04 installed on my desktop, I could use my phone, via usb0 interface, to connect to the internet at the same time as using the router on eth0. But now I have 10.04 on the computer, and it won't let me use both interfaces at the same time: I have to unconnect the router before I can use usb0.
Fedora :: Unable Get Wireless Working After Connecting To Eth0?
Aug 12, 2010I installed F13 on an Acer laptop for a friend who is just beginning with Linux. This laptop has the dreaded Broadcom chipset and is using the b43 driver. When it was first installed, wireless was automatically detected and worked fine. However, as usual, there was about 200MB of updates after the install, and the wireless was downloading extremely slowly, so I connected eth0 just to complete the updates. Ever since, the wireless will not work. When the machine is booted, wireless is shown as disabled in Network Manager. I remembered that there was a wireless switch on the front of the laptop and switching it on allows me to check the enable wireless box, but wireless says device not ready.
ifconfig wlan0 up returns:
Code:
SIOCSFFLAGS: Operation not possible due to RF-kill
I assumed this meant that the switch was in OFF position, but it is not. iwconfig shows the wireless is detected. It appears that there is a script for rf_kill somewhere in the filesystem that is keeping this from working.
Networking :: Unable To Locate Eth0 With Ifconfig In Fedora 12 ?
Apr 26, 2010I've got a vmware install of Fedora 12 running as a server. This install has the /etc/sysconfig/network-scripts/ifcfg-eth0 file configured with the proper info and the service has been restarted. When I run ifconfig I only get the loopback interface, when I run ifconfig -a I can get the eth0, but without the pre-configured ip address. When I enter ifconfig eth0 up I can activate the interface, but without the afore mentioned ip address. I need to be able to yum ssh, install it, and run it with rsa keys. Can do none of this without an interface obviously.
View 3 Replies View RelatedFedora Networking :: Unable To Activate Eth0 Connection / Resolve This?
Jul 25, 2010Code...
connection is set to connect automatically using dhcp... used to work, after a latest updates basically stopped working.
Networking :: Eth0 Fixed IP - Eth1 DHCP Gateway - Access To Eth0?
Aug 19, 20095.10 Breezy configured as machine controller. Works great eth0 is a fixed IP to communicate with controller comms board. Not easy at all to alter - the comms board is hard coded to listen on eth0 for commands.
I can use eth1 as the default gateway and ping google.com, etc. But when I now attempt to communicate with the controller with netcat, e.g.
Code: echo !HH | nc 192.168.1.6 80
I obviously never get an answer since the request is passed via eth1. Using the -g option with netcat doesn't work either. I had a look at iptables but it doesn't seem to be able to do what I want. How I can still use eth0 as my communication port to the controller whilst eth1 is the default gateway?
Networking :: Production Server With Static IPs On Eth0 And Eth0:1 - Getting Private LAN On Eth1?
Jul 1, 2010I have two servers on a vlan at my datacentre/colocation and previously both servers had public IPs on their eth0 interfaces. The servers are HP ProLiant DL360s - one is a G4 and one is a G5 The newer G5 is now the LAMP server and the G4 has been retired and I want to repurpose it as an iSCSI target using openfiler freenas or similar.
My G5 has public/static IPs lashed to the eth0 physical interface and the eth1 is not configured to do anything yet. The G4 will have both interfaces available - perhaps one for ssh access from one of my static public IPs and the other to be a private IP on the local vlan. Here is what I am trying to get my head around...
The G5
eth0 - Public IP - full LAMP services on two or three virtual interfaces
eth1 - Private IP 192.168.0.1
The G4
eth0 - Public IP for ssh
eth1 - Private IP 192.168.0.2
Because my traffic between eth1 on these boxes is via private IPs on the local private vlan it doesn't add to my quota for bandwidth. How do I go about configuring the routing and gateways and other aspects of this so that I can run a private IP space network between the eth1s and still serve the outside world from the eth0s...
I am afraid that if I assign the private IPs to the eth1 interfaces the routing may either not work or interfere with the access to the production internet facing interfaces (eth0s).
Ubuntu :: Eth0 Doesn't Exists For Firestarter - Eth0: Error Fetching Interface Information: Device Not Found
May 5, 2010My network name is eth2 it was changed by some reason and now i got these errors... i installed, reinstalled, re re installed, tried to run the asistant but no luck :/
Code:
* Stopping the Firestarter firewall...
eth0: error fetching interface information: Device not found
eth0: error fetching interface information: Device not found
eth0: error fetching interface information: Device not found
[code]....
Debian :: Eth0 Disapears And No Eth0 Inteface Found
Jul 13, 2009On my machine (Desktop PC) I have 2 network card : wireless (rt61 802.11) and a wired card (BCM44). When I install debian 5.
The wired card is detected and logical name eth0 is assigned, while wireless is not assigned I install firmeware* software to configure the card. It is done in some way ( I used mnetwork from mepis, it works fine).
Now the problem: eth0 disapears, and no eth0 inteface found? ifconfig gives just wlan0.
Question: Why there is no eth0, it was before configuration of wlan0 ?
How to active again eth0, or ho to create the logical eth0?
Networking :: Ignoring The Unknown Interface Eth0=eth0?
Dec 18, 2010I'm running a dual boot Ubuntu 10.04/Backtrack 4 (Ubuntu 8.10) system. I can get internet in the BT4 side but not in the Lucid side. In Lucid I can ping my router, and the network manager says I'm good to go, but I can't get to any web sites. It all started when I tried to put my laptop on another network by mimicking the settings of a computer I had just unplugged from the network. MAC address and all.
ifconfig eth0:
Code:
eth0 Link encap:Ethernet HWaddr 00:1f:16:ba:4c:8c
inet addr:10.136.9.147 Bcast:10.136.9.159 Mask:255.255.255.240
inet6 addr: fe80::21f:16ff:feba:4c8c/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]....
OpenSUSE Hardware :: Realtek NIC Installation - Unable To Configure The Network Card Because Kernel Device (eth0, Wlan0) Is Not Present
Nov 30, 2010Installed a TP-Link TG-3269 Gigabit card in a machine running OS 11.3 32 bit, when I go into Yast, Network Devices, Network to try configuring the card I get this errormsg: Unable to configure the network card because the kernel device (eth0, wlan0) is not present. This is mostly caused by missing firmware (for wlan devices). See dmesg output for details. Couldn't find any mention of the card in dmesg's output, (though the 8139 onboard card is in there) there is some stuff about pci host bridge but I don't know whether they would be relevant or not
The chip on the card says it's rtl8169sc but lspci lists it as being 00:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. Device 8369 (rev 10) Done some googling and there don't seem be any drivers for a Realtek 8639 and it returns no matches from a search on realtek's site, but there is a driver there for rtl8169sc chips, which I downloaded and installed, no errors when installing it Even after a reboot I still get the same error in Yast's Network Settings screen, lspci still lists it as 8369 and the device isn't listed at all if I run ifconfig
Fedora Hardware :: Unable To " Ethtool -s Eth0 Speed 1000 Duplex Full"?
Nov 5, 2010have a " Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06)" NIC.I was unable to set it 1000bit and full duplexThe output lspci -v as below.Quote:
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06)
Subsystem: ASUSTeK Computer Inc. Device 8432
[code]...
CentOS 5 Networking :: Kernel Rpm Install After Error "Bringing Up Interface Eth0: Device Eth0 Has Different MAC Address Than Expected, Ignoring"
Dec 26, 2010i install kernel rpm after i boot that kernel network not working kernel name : kernel-rt-trace-2.6.24.7-132.el5.centos.i686 [URL] error "Bringing up interface eth0: Device eth0 has different MAC address than expected, ignoring."
View 1 Replies View RelatedNetworking :: Sending Video Streams From Eth0 And Eth1 To The Other Server Programs' Eth0 And Eth1?
Jul 30, 2010I try to generate a server client code. What i try to do is sending video streams from eth0 and eth1 to the other server programs' eth0 and eth1. In order to do that, i decided to use SO_BINDTODEVICE. But the code is not working. Am i misunderstood the usage of SO_BINDTODEVICE.
1-Defining two ports
2-Defining two sockets
3-Assigning host ips on them
[code]....
Slackware :: Lilo Not Activating ?
May 16, 2011I finally got everything installed and then slackware setup prompted me to reboot. then i did and it just took me back to windowsxpx64. so then i tried booting off my usb, and it worked, however when i login as root, i just get the bash commandline and not interface or programs or anything. i cannot login as any other user and the setup did not prompt me to make another user account. so how would i activate lilo or make it so i can boot with it to slackware? i rather use grub but for now i would just like to get slackware working right.
View 2 Replies View RelatedDebian Installation :: Activating DNS On New Install
Nov 30, 2015I just installed debian Jessie (8) and find that the system cannot resolve URLs. Checking with the "hosts" command confirms this. I am connected to a comcast network in my house. I have looked over some of the documentation and it seems like there are several conflicting ways of setting up the resolver. It is not clear if the install process did this for me. I am assuming that DHCP was installed as the computer had no problem defining IPs for its wlan0 and eth0 ports and I can telnet in from and in-network PC. I have a few questions :
1) I see /sbin/dhclient/,,,,, running so i assume this is the DHCP deamon in use?
2) Before I dig too deep I wonder if an internal firewall is involved. Is there a command to shut it down temporarily?
3) what would I look for to determine if a resolver was installed and which one?
I see from my windows machine an apparent comcast DNS server but I don't believe I can code it into resolv.conf on debian as the OS now overwrites this(I already tried and failed!).
Fedora :: Error Activating Xkb Configuration
Mar 2, 2009Since the last update of xorg/x-server I am receiving following error after logging into my gnome desktop:
Code:
After updating fedora on my laptop there's the same error. I found this thread here in the forums but the link inside is dead. [url]
According to some google-results it has something to do with the gnome settings not being the same as the X-server settings.
Fedora :: Gnome-screensaver Not Activating
Dec 11, 2010I'm running Fedora 12 and the last couple days I have noticed my screensaver will not start anymore. I did a yum update a few days ago don't know if there is a connection between the two. I've just started to Google the topic. Found different culprits ranging from dbus problems to buggy code.
I'm using a x86_64 PC running kernel 2.6.32.23-170.fc12.x86_64. My Gnome version is 2.28.2. The Gnome-screensaver version is 2.28.3-1.fc12.x86_64.
Ubuntu :: Activating Swap File ?
Mar 19, 2010I am using ubuntu 9.04 on my laptop from past 8 months. These days when I boot my laptop, The booting process takes more time on the following step:
Activating swap file
Fedora :: What Are The Steps In Activating FTP And Telnet On 10
Jan 11, 2009SSH is initially installed and activated. What are the steps in activating FTP and Telnet on Fedora 10. I know they are non-secure and probably shouldn't be used at all, but I need to know or at least pointed in the right direction.
View 3 Replies View RelatedSlackware :: Activating Cpu Frequency Scaling ?
May 15, 2011Slackware64 13.37 multilib, generic kernel (full install)
BIOS: EIST and C3/C6/C7 State support are enabled.
I'm trying to activate cpu frequency scaling following the tutorial on slackwiki: [url]
I can't load any module.
Code:
I've tried all of them but the error is the same. I also rebooted to the huge kernel, however, it gave me the same error.
Debian :: Activating Network - Root Account ?
May 13, 2010How do I activate networking? (I am currently logged in from Ubuntu on another computer). I installed Debian Squeeze on an iMac 7.1 (which works perfectly well with ubuntu) from the netinstall CD (today's daily build), and of course I deactivated root login, coming from ubuntu. Now I find I have to enter my root password (login password will not do) to activate networking! Is this a joke? I had the network configured with DHCP during install! So how do I activate the root account, or, more to the point, how do I get by in Debian without activating root login?
View 5 Replies View RelatedFedora :: Activating Printer On Parallel Port?
Apr 18, 2011When I boot fc14 with an already defined printer connected on the parallel port, then I can use the printer. The printer appears on parallel:/dev/lp0. But, if the printer is not connected during startup, when I connect the printer I cannot use it. Nothing happens. I have no corresponding message using "dmesg" command when I connect the printer.
I cannot make cups see that the printer is connected, using "localhost:631" in firefox. Is it possible to "mount" the printer manually? Using "system-config-printer", the printer has to be "activated", even though it is not used or even connected. Then "parport" module is installed during boot (with other related modules: "ppdev" and "parport_pc").
Then, when the printer is connected, "dmesg" shows :
lp0: using parport0 (interrupt-driven).
lp0: console ready
And, of course, it is now OK to use the printer.