I recently bought 1GB video card of 'xfx radeon hd 5450'. It came with cd for drivers of windows.
I installed fglrx. Still in ubuntu 10.10 (lucid) I ran: lspci -v | grep -i prefetchable
which shows 256M which is video memory of my ASUS motherboard.
Just purchased and installed an ATI Radeon HD 5450 graphics card and installed the proprietary drivers via System > Administration > Hardware Drivers. After rebooting the machine X would not load so I restarted into recovery and removed my xorg.conf. At this point I could restart normally and the machine would let me into X. I went to System > Preferences > ATI Catalyst Control Center to try and configure the card.
I receive the following message:
There was a problem initializing Catalyst Control Center Linux edition. It could be caused by the following. No ATI graphics driver is installed, or the ATI Driver is not functioning properly. Please install the ATI driver appropriate for your ATI hardware, or configure using aticonfig.
So, I did just that, I restored my backup xorg.conf (configured for nvidia card) and executed 'sudo aticonfig --initial', it made the proper changes and additions to the configuration file and this is what it looks like [view xorg.conf]. I then restarted the machine and X still refuses to begin [view Xorg.0.log]. Again, I went in removed the xorg.conf file and the machine will load normally. I tried running fglrxinfo to try and see if the card was properly installed and it just threw a segmentation fault.
Few week back I downloaded this driver ati-driver-installer-10-12-x86.x86_64 from AMD/ATI. Everything when ok then I decided to reboot f@@@@K the system up kept rebooting all the time so I did a fresh install again and downloaded the Driver again but this time I need QA. Is this driver will solve my issue of Accelerated 3D graphics is not available? Will this mess everything up again? If so how can I recover without having to do a fresh install?
View 2 Replies View Relatedi got a dell computer running ubuntu. it is equipped with an ATI radeon 5450, using a dell IN2010 1600x900 screen. when i installed ubuntu, the resolution was just fine. then i installed the ATI driver, and from that moment on, i have that strange behaviour: when i start ubuntu, the resolution seems set to 1440x900, but stretched to wide-screen mode, so the font is somehow blurry. when i turn the monitor off and then on again, everything is just fine.i have catalyst control center installed, and the resolution is set to 1600x900, but i still have the problem that i described.
View 7 Replies View RelatedAfter installation of the new hardware I activated the ATI closed source driver. There is an issue with the screens
1st screen, via DVI: I cannot change to the native screen resolution
2nd screen, via VGA: The background of any window is not drawn.
Means: I can see lots of parts of other windows after moving or closing them.
Therefore I was searching for an alternative and found the hint to uninstall the ATI driver and use the open source one. After uninstall and reboot (requested by a parallel system update), some boot messages I have no screen output anymore. Means: two black screens. These are going into sleep mode after a few seconds. How can I get a running system again? Optimal would be, that I have full support for both screens. Same happens in failsave mode.
System environment:
Ubuntu 10.04
AMD Athlon 64 X2 3800+, 4G RAM, motherboard ALiveNF6G-DVI (internal graphic deactivated), ATI Radeon HD 5450
Installed Ubuntu 10.10 on fresh HP dm4-1050so laptop and encountered problems, this is one of them. Noticed that ATI card is heating heavely with default installation and I would like disable it and switch to use Intel's GMA. Also tested ATI proprietary fglrx driver through Administration->Additional Drivers, after booting got empty screen so I switched back. Afterwards read from documentation that 5450 is not supported, so no wonder. So what is the simplest way of disabling ATI and using only Intel's gma? Here's what I got with lspci -v:
Code:
00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02) (prog-if 00 [VGA controller])
Subsystem: Hewlett-Packard Company Device 1469
Flags: bus master, fast devsel, latency 0, IRQ 45
Memory at c0000000 (64-bit, non-prefetchable) [size=4M]
[Code]...
I recently installed ubuntu 10.10 on HTPC, after having a few RAM and SATA issues everything seems to be working fine, The audio (using HDMI) does not work. Have PC connected using HDMI for video (and I am hoping for audio too, this card is made for this and it has been tested with other OS) however the audio does not work, although in the audio preferences it shows to be using the correct hardware. Testing for sound under sound preferences does not play anything, acts as it it was, but no sound, no error messages either. I went ahead and installed ATIs proprietary drivers in hopes that it would make the audio work, but not luck so far.
View 6 Replies View RelatedI have installed a 9200 Radeon (the card says 9250 on it, but computer reads as 9200) on a AMD Sempron 2500+ 64 bit,Ubuntu 10.04 Gnome 2.30.2, Kernel Linux 2.6.32-26; Samsung VGA 941BW monitor.
A friend told me if I added more RAM (512mb), the card would run properly & the graphics would be stellar.
He also told me the drivers were installed.
When I did this & started the computer, before I got to my login, a box appeared, telling me my graphics were running in "Low Mode", & do I want to configure them. When I said "Yes", it told me to restart. When I did, nothing happened & the video card is still running on "low". I checked the fglrx info, and was told "command not found".
I'm running Ubuntu 9.10 on an HP Desktop with an ATI Radeon 2600 pci card that has four outputs. I want to run the same 3-monitor array that I had in windows. Is it possible to get this thing running and configured right in Linux? At the moment I can only get it to send a signal to 2 monitors. I installed the drivers step by step from the manufacturer, but I can't seem to get a signal to all 3 monitors.
View 6 Replies View RelatedThere is running gOS on my computer (Ubuntu baset OS) and I want to install the Video Card driver for ATI RADEON 9250.
Ifound the driver in the official site =>> http://ati.amd.com/support/drivers/l...n-prer200.html
And I also saw the instructions of installation =>> [url]
But I cant instal the driver. When I write the comand sh ./ati-driver-installer-8.28.8.run (of course the file is in the home directory)the terminal window writes:
PHP Code:
And then written in the instruction: The ATI Proprietary Linux Driver Setup dialog box is displayed but no window or dialog box is displayd.
Using this video card but unable to find the setting for it in the options. I am using a generic VGA setting right now and it's getting less than optimum resolution. What's the proper setting for this card?
This is RedHat Enterprise edition.
The machine is Dell OptiPlex 745
The monitor is Dell 2005FPW (Digital)
The graphics is:
ATI Radeon X1300 Professional
I'm attempting to get Debian (Squeeze, latest net-install CD) working on a Power Mac G5 Quad with a Radeon X1900 Mac edition video card (PCI-Express.) The installer acted a bit weird right from the start, telling me that the step "Install the system" failed (with nothing in the way of useful error information,) but I got the base system installed at least. It booted fine to framebuffer console, so I set about installing GNOME on it. apt finished with nary a complaint, but when I rebooted, I found that when it's ready to launch into X, it chokes up and just sits there with a blank screen and a cursor. (Weirdly, though, the screen itself flickers on and off at a high rate, faster than the actual cursor blink.)
Framebuffer console still works, at least, so I was able to boot into single-user mode and do some investigating in my own limited capacity for this stuff (by which I mean "Google error messages and see what specifics are requested.") lspci -k shows the video card properly with the manufacturer and product name, so it is recognizing it, at least. When I try Xorg -configure, though (Xorg 1.7.7, it says,) it aborts with a "No DRICreatePCIBusID symbol" message. Checking dmesg gives me a "process Xorg mapped non-existing PCI legacy memory" message, followed by an "invalid ROM contents" message underneath.
I'm not sure what all to make of this. I've found a thread about problems getting the same basic setup (G5 Quad, X1900, Debian) to work, but it's a couple years old and the symptoms are different. There's some discussion there about the radeon/radeonhd driver looking for Atom BIOS information on non-Atom BIOS cards, which would explain the "invalid ROM contents" message, but on the other hand, if lspci recognizes the card properly, would that be the problem? I don't know. Obviously it's playing nicely enough to run framebuffer console output properly, but beyond that I have no idea. I'd really like to get this working - it'd really improve things over the GeForce 6600 it came with...
a powermac G4 with radeon 9000 RV250 in ubuntu 10.04 ppc i just want the graphic work better
View 9 Replies View RelatedI've loaded Fedora and must say what a nice OS! But I'm having some issues getting the video working correctly so let me jump right into the issue. The video is very garbled and hard to read. can't seem to find a way to correct what would appear to be a driver issue. Here are a list of things tried:
- display works fine with Ubuntu
- display is clear but is chopped off when using an external monitor from onboard vga slot
The video card is an ATI radeon and the linux drivers from the ATI site don't work with the new images that are out yet.
Will Fedora 15 support this video card on laptops?
View 2 Replies View RelatedI'm trying to install the driver for my ATI Radeon X1600 Series video card. I got the driver from the ATI site. Heres the link: [URL]... I'm using 10.04 LTS. I have attached a screenshot of the message I get when I run the installer.
View 4 Replies View RelatedI'm a new Mandriva user,and have no clue about Linux system,but to be honest I don't want to use Windows product anymore. So I got the Mandriva 1 Spring Gnome,and installed it on my DELL Optiplex Desktop,works fine and very fast,therefore I decided to do the same with my Studio XPS 1640,but after I got a dark screen,so I used an external display(My TV) then realized that it doesn't support the video card on it ( ATI Radeon HD4670 ),and I don't know what to do.
View 1 Replies View RelatedI have ATI graphic card with HDMI video and Audio:
I see that I have HDMI connector and S/PDIF connector on the mortherboard, I just have HDMI connector on the monitor, I have no problem with the video but the audio does not work, I just want to confirm that the audio should also go throught the HDMI cable right ?
Here is the output from the alsa-info.sh script.
I been searching for months on how to get the s-video to work on my pci VGA compatible controller: ATI Technologies Inc Radeon Mobility M7 LW [Radeon Mobility 7500] card. I found a site with instructions.
This is how I got it to work.
I install Debian 5.0 Lenny Desktop
added the Driver "radeon" to my /etc/X11/xorg.conf file
This work and I was able to use my tv as a monitor however when I try to play a video file from totem or vlc all I could get was audio with no video; These files work and played fine in the CRT monitor.
I came across this article, which I found to be very interesting and thought share it with you all.
Graphics CardMemory as swap space or RAM disk.
[URL]
Have downloaded ubuntu (because my linux lite died). Very pleased so far with ubuntu, but I can't figure out how to access files or photos from a memory card. Just can't seem to go to anything that even shows its existence.
View 3 Replies View RelatedIs there a 'top' like command for monitoring the GPU and memory usage of a video card? I am most interested in Linux commands, but and OS would be interesting. I strongly suspect that for a group of my systems the video cards are being under-utilized (but I have no idea by how much) and would like to re-allocate funds to other bottle-necks. We are using higher end cards, so the price difference between cards is significant.
View 1 Replies View RelatedI'm looking at buying this card and I'm wondering if anyone here has had an issue using this card with Ubuntu(currently on 9.10)
[URL]
Fedora 12, latest kernel, x86_64.
I have an Asus M4A78L-M motherboard that has integrated ATI Radeon HD3000 video. Should I be looking for a driver specific to the integrated video, or should I be looking for a driver specific to the motherboard? I'm not sure if I should look for something different if the video is integrated onto the motherboard, as opposed to a separate video card. This is what I found: http://support.amd.com/us/gpudownloa...5&lang=English
Are there best practices for updating video drivers before I make any changes? I don't want to hose my video.
I am looking to build a new desktop. What is the lowest end video card that will fits the following:
Supports 2 monitors at 1920x1200 or 1600x1200
Works with Linux.
3d performance isn't much of an issue, since I don't play computer games. I use the computer mostly for programming, which is why I like having the large resolution, so I don't have to scroll around so much.
I've been playing around with Damn Small Linux 4.4.10 on my Dell Inspiron 3000 laptop for quite a while now, and this is the first time I've been downright stumped. To make a long story short, I'm trying to play 480p video on a machine with a 233 MHz Pentium processor, 112 MB of ram, and a Neomagic MagicGraph 128XD graphics card (NM2160). Crazy? Maybe, but I don't think so. I'm using MPlayer set to Xv mode with the XFree86 4.3.0 server, and so far, I've been able to get it to play 360p mpegs with minimal stuttering. However, MPlayer crashes with 480p. This is because the 128XD only has 2 MB of memory, which, after the 1024x768x16 screen takes its share, doesn't leave enough room for a 640x480 overlay.
The creators of MPlayer are aware of this limitation, and suggest adding the following line to my XF86Config file: Option "OverlayMem" "829440"
As I understand it, this is supposed to extend the video card's frame buffer into system memory, thus allowing the higher resolution video to play. However, it doesn't work, based on this output from my XFree86 log file: cannot reserve 829440 bytes for overlay...
Some other suspicious-looking lines from the log file:
I have a Radeon HD 5830 card and it just doesn't seem to be working to it's full potential. I've tried TF2 and SC2 through the latest stable release of Wine, but the frame rates are horrible.
Also, when I run fgl_glxgears, I only get 800fps. (If I reboot the computer and run fgl_glxgears as soon as I log in, I get at least 3000fps for a few seconds. Then it's back to 800)
I've tried reinstalling the driver several times.
Why is the performance so low?
Here's my setup:
XFX Radeon 5830
Ubuntu 11.04 (fresh install and updated)
11.5 ATI driver from AMD's site. Here is fglrxinfo output:
[Code].....
I had a problem with OpenGL on my computer (I run Ubuntu), and so I created a thread here: [url] but it turned out that the problem was with my graphics card, so I made a new thread at the Ubuntu forum at [ubuntu] Problem with OpenGL in Ubuntu - Ubuntu
View 4 Replies View RelatedI decided to put a Radeon 8500DV card in my Slackware box. Works fine with the Vesa driver. Problem is, I'm using a widescreen monitor, and Vesa doesn't support my default resolution (1366x768). So I thought I'd do a little editing in my xorg.conf file and fix it right up.
I logged on as root, and did "X -configure", then I went in and edited the file it made me and put in the appropriate values for my monitor and resolution. And then it copied it over my xorg.conf file, and typed startx. Voila! Looked great, and I checked the settings to be sure I was in 1366x768. It worked fine!
Once.
Then I logged out and tried "startx" with my user account. As soon as I do, my monitor displays "No Signal"... weird - cause it just worked. So I rebooted, and logged on as root, and tried startx again. "No Signal"
So why would it work just once and not again. I tried repeating my steps exactly, and still can't get it to come up.
Here is the xorg.conf I used when it did work:
Quote:
Originally Posted by xorg.conf
Section "Files"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/local"
FontPath "/usr/share/fonts/TTF"
FontPath "/usr/share/fonts/OTF"
[Code].....
I tried removing the Card1 and Screen1 sections (since they are invalid), but that made no difference.
according to this, the radeon kernel module is not recognizing my card. This is disabling DRM in Xorg.
Here are the Xorg errors:
Code:
(II) Loading extension XFree86-DRI
(II) Loading extension DRI2
(EE) RADEON(0): [dri] RADEONDRIGetVersion failed to open the DRM
[dri] Disabling DRI.
[Code]....