I am looking to build a new desktop. What is the lowest end video card that will fits the following:
Supports 2 monitors at 1920x1200 or 1600x1200
Works with Linux.
3d performance isn't much of an issue, since I don't play computer games. I use the computer mostly for programming, which is why I like having the large resolution, so I don't have to scroll around so much.
I just got another video card from a friend and I wanted to see if I could get it to display a second screen. I have two monitors, both VGA CRT monitors. The first video card is a Geforce 8400gs pci-e and the card given to me is a Geforce FX 5500 pci. I could get them both to work separately under low graphics mode when I go into the bios and switch the video adapter from pci-e to pci, but not together. What to do to make both cards work in harmony?
View 4 Replies View RelatedIs there a simple way to have both of the monitors on a system enabled? The video cards are both older ATI cards. One is a Radeon 9000 AGP 64MB, and the other is quite a bit older (ATI 3D Rage Pro 2x). When Ubuntu 10.10 is booting up, the splash screen appears nicely on the left-side monitor, and then the final desktop appears on the right-side monitor, but when I go to system --> preferences --> monitors, only one monitor is available. I'm guessing the right monitor is fed by the Radeon (I can check if it matters). If the splash screen appears on the left side when booting, why isn't that display available after the bootup has completed?
View 1 Replies View RelatedI'm running Ubuntu 9.10 on an HP Desktop with an ATI Radeon 2600 pci card that has four outputs. I want to run the same 3-monitor array that I had in windows. Is it possible to get this thing running and configured right in Linux? At the moment I can only get it to send a signal to 2 monitors. I installed the drivers step by step from the manufacturer, but I can't seem to get a signal to all 3 monitors.
View 6 Replies View RelatedI'm building a new Ubuntu system for use as a desktop machine and personal server (http, smb, smtp). It'll be based on an Intel i7 950 and a Gigabyte X58A-UD3R LGA 1366 ATX Motherboard.
I'm looking for recommendations for a graphics card that will support dual monitors and runs well under Ubuntu. Would like some decent 3D support.
after I installed the ATI Radeon 3400 series video card in my machine, the Xserver cant start! after it loads, it takes me to the init 3. When I tried startx, the screens either go blank or doesnt let me. I tried to install everything following this website:
[URL]
I wanted dual monitors but now I cant even get one. The xwindows doesnt appear. Things I tried:
1. Deleted the xorg.conf and reconfigured (didnt work).
2. sax2 -r -m 0=versa (didnt work)
3. reconfigured the ATI radeon driver from init 3 (didnt work)
4. copy and paste the oold version of xorg.conf (didnt work)
5. tried to run set apt or dpkg-reconfigure command (commands not found)
6. tried xconfig and prompt the best I coudl (didnt work).
7. aticonfig commands (As shown in website) (also didnt work)
I have the live CD to run it from there but I dont know what to do once I get to the terminal. Is there any way I can revert to previous configuration since the ATI driver gives me some problems? Like a restore function in windows? how or what files I should change for the X-server to run properly (is there any other file than xorg.conf?....)
The monitors I have:
2009W Dell Monitor
1398 Dell Monitor (I wan to get the dual exntended monitor but it seems to gave me only the mirror image, thats why I tried to reconfigure the video card)
VideoCard:
ATI HD Radeon Mobile 3400 Series
Computer:
Dell Optiplex 680 (i believe) with SUSE 11.26 and x86_64 bit
I used preupgrade to upgrade from F11 to F12. In F11, I used the proprietary nVidia drivers from rpmfusion, and they worked well. I have refrained from installing the nVidia drivers in F12, because of the problems reported for users of KDE. I removed my old xorg.conf, which has references to the nVidia driver and to "TwinView," the proprietary method of managing two screens, so as to let X discover both monitors.
Now, however, my second monitor stays black, even though xrandr and KDE RandR show both monitors correctly. Xorg.0.log shows the nouveau driver is loaded. (I also tried to create a new xorg.conf following guidelines from the web, but many of the guidelines are from before xrandr, and I'm not confident I have it right yet.) It seems that X believes I have two monitors, because I can drag a window off into the blackness (and it's never heard from again!) I know that the hardware is working, because I just booted into Windows 7, and I could see the desktop on both windows.
How do I convince X and KDE to display on both monitors?
I'm busy building a machine now and I'm looking to set up dual monitors because it's something I've always fancied but never had the resources to do. I'm basically looking for advice on choosing a graphics card that will support dual monitors with good driver support under Ubuntu. After a few hours of browsing the forums I determined nVidia were the way to go but I'm honestly not bothered if people want to suggest ATI. I'm not a gamer so really only need the card to support dual monitors. I'll also need to know how to set up the card under Ubuntu and then subsequently how to edit xorg.conf in order to get the dual monitors working.
View 6 Replies View RelatedI have a Dell Studio 1558 laptop with a 1366x768 resolution screen. I have an LG flatron monitor with a 1600x900 resolution screen. The screen is connected to the laptop via a vga cable.I am using the fglrx driver and have tried to configure the dual monitors through the ati catalyst user interface, aswell as through the gnome preferences>monitors user interface.
The problem is that I can move the mouse cursor over the top of the laptop screen. I think there is possibly some problem with a virtual desktop size of 900px high. Even in the gnome and ati monitor configuration UI's it shows a highlighted empty space above the placement of the laptop screen. This is very annoying as files on the desktop go north of the laptop screen when sorted by name, and the mouse just randomly disappears off the top of the screen sometimes.
Here is my xorg.conf, would really appreciate it if anyone can help me out here.
Section "ServerLayout"
Identifier "Default Layout"
Screen 0 "amdcccle-Screen[2]-0" 0 0
EndSection
[code]....
I have an image generator (IG) running 64-bit Ubuntu Linux, GNOME & the SAGE application all running through an NVIDIA Quadra FX4500-X2 (dual GPU). Had to install a new FX4700-X2 (and the latest drivers) because 4500's are unavailable. The computer works fine except but I cannot watch the whole boot up sequence on the same DVI port anymore.On the 4500, all video came out the lower DVI port of the GPU with the PCI-X connector (let's call that the "a" GPU). But on the 4700 card, the screens you see during boot are divvied up between the lower DVI port of each GPU. The POST screen through Ubuntu splash screen comes out the "b" GPU while the "a" GPU is blank. The SAGE Initialization page and SAGE Desktop comes out the "a" GPU while the "b" GPU is blank.
I logged in as root and looked for a GNOME menu allowing me to force all video through the same GPU & DVI port, but couldn't find anything remotely close. Any suggestions on where I can look? Technically this IG is working, but I want to fix this to avoid future wild goose chases. The system uses 52 of these IG's.
I have about 60 old PC's that have an 8X AGP slot. What used/old AGP video cards are there that are supported, that are cheap and will provide a 1280x768 (or there abouts) for a generic lcd wide screen display?I've seen several Dell nVidea 5200 w/64mb AGP cards for under $10.
View 7 Replies View RelatedI'm looking for a PCI RAID card that will support 4 SATA disks in RAID 5.
Essentially it must be possible to monitor the raid from the Linux operating system (FC10+), I will not have physical access to the machine most of the time, so I need to be able to talk to the RAID card from Linux (like the 3Ware one does), It is possible to get reasonably priced RAID cards that can be monitored from Windows.
Finally replaced my incredibly antiquated Ti 4200 with a GeForce 9600 GT, but I'm having a few problems. The main one would be that I can't see anything when I drop to terminal (the monitor shuts off)- I could when I had a spare svga monitor hooked up through an adapter, but now I'm using dual DVI monitors. Do not have an svga cable to spare at the moment. The second seems to be a doublethink problem- a good while back when this computer was a fresh install, I could have sworn I had the option for the resolution 1680x1024- this is an *essential* resolution for twinview, because my second monitor is 1280x1024, and setting this widescreen to 5:4 is just... wrong.Simple restart solved the terminal issue (I hotplugged the monitors). Resolution thing is still a standing issue. I have a 1050 capable monitor, but the display portion is an inch shorter than the widescreen.
View 3 Replies View RelatedI installed the latest nVidia drivers on my laptop using the 9800M card. The laptop is a Gateway P-7805u and I'm connected to the second monitor using VGA.Also, before installing the nVidia drivers (and just using the basic drivers included with Kubuntu 10.04), basic dual monitor support worked, except I could not enable compositing features for some reason. So I thought the proprietary drivers would fix this.Several issues have arisen since installation:
1) I've clicked through all of the display settings to activate the second screen with absolutely no change.
2) When I try to apply settings and Save Configuration as the nVidia help suggests, I am told that I cannot save to the X.conf file. I assume this is due to innate permissions on my user settings, which I have no idea how to properly configure.
3) I have no idea where to go from here, as most of the fixes I found online involve Linux syntax and verbiage, to which I'm totally clueless after spending over half my life with Windows.
I currently use "MSI Radeon HD 3650 Graphics Card - ATi Radeon HD 3650 750MHz - 512MB GDDR3 SDRAM - PCI Express" that have no HDMI and some problems with Ubuntu. Due to the Ubuntu compatibility problems I decided to ask you guys for recommendations before upgrading to a new video card.The only "demand" is that the card must have dual HDMI outputs, one for the monitor and one for the TV.
View 6 Replies View RelatedI, too, have a dual-monitor set up. I would like to use one monitor to run X11, and the other to run a text-only mode, like when you press ctrl+alt+fX, where 1 <= X <= 6.
View 2 Replies View RelatedCan any recommend a PCIe video card for my AMD64 box?Looking for one which basically has a good working driver:
- can do dual head using DVI and VGA output.
- open source preferably, I've used the nvidia proprietary one before, was fine but kernel upgrades became a pain.
- passive heatsink so it's silent, doesn't need to be a fast card since my other two were both onboard graphics.
- driver can do KMS for nifty high res console.
- most typical features work, so Mplayer plays nicely and can scale to full screen etc. (xv output +/- accelerated decoding)
- even a bit of light 3D for openarena or compiz would be nice.
- don't mind buying second hand if they aren't available new
I've had a Nvidia 7050 on board which was ok, fast enough, but upgrading with the proprietary driver became painful, and that motherboard is dying a flaky death.
- The nouveau driver looked promising, but wasn't really in Debian at that stage. But I did once accidently boot a high res console while testing a brand new kernel (2.6.31 I think) and was blown away Currently got an ATI RS880 [Radeon HD 4200] on board which is fine, 2D is fast enough, but the open source driver isn't finished yet. It can't do dual head (horrible distortion and crashes), can't suspend to ram (freezes), Xvideo and any form of 3D acceleration are missing.
In Synergy, is it possible to set up your config so that you have one server and one client, both with dual monitors, but the client machine has its monitors such that one is on the left of the server's left monitor, and the other is on the right of the server's right monitor? For example:
+----------+ +----------+ +----------+ +----------+
| client | | server | | server | | client |
| screen1 | | screen1 | | screen2 | | screen2 |
+----------+ +----------+ +----------+ +----------+
Hopefully my ASCII is good enough to understand. Both machines will be running Linux. If there's a way to do it by messing with xorg configs that would be perfectly acceptable too.
I'm using gnome in a dual-head setup with individual desktops. Is there any way to "jump" to another monitor using the keyboard only? Now the only method I know is to move the mouse pointer to the another screen and click on something there. Can I do something like that without using the mouse?
View 3 Replies View RelatedI have 2 screens connected to my nVidia 8400GS and would like to change my video card settings so that the system boot shows in the Digital screen and not in the Analog one.
View 3 Replies View RelatedI have repeatedly installed CentOS 5.5 64-bit on a Dell T3500 with an nVidia Quadro FX 580, in an attempt to get dual monitor support to work to no avail. Everything works fine when just one monitor is plugged in and I do not try to enable or plug in a second monitor. I have installed the Dell DKMS, and the Dell recommended drivers (from Dell site) on one installation, I installed the nVidia drivers (from nVidia site) on another, and have tried with what CentOS loads by default on another. The results are the same every time: When I reboot as directed I get a black screen. I can recover by hard shutdown and unplugging one of the monitors, but that doesn't solve my problem. Has anyone had a similar experience, or have any helpful guidance? I am not very Linux savvy. This is for multiple machines in a corporate environment.
Information for general problems.
== BEGIN uname -rmi ==
2.6.18-194.26.1.el5 x86_64 x86_64
== END uname -rmi ==
== BEGIN rpm -q centos-release ==
centos-release-5-5.el5.centos
== END rpm -q centos-release ==
[Code]...
I have two Ubuntu 10.4 machines (and Ubuntu continues to hide more and more xorg.conf config such that I no longer know where to find it). One is a laptop running dual headed - DP1 is the internal screen, and VGA1 is an external monitor; both are running at 1600x900. The other machine is a desktop running both VGA1 and HDMI1 (which is actually a display port with a DVI adapter) at 1600x900. So in both instances my desktop is 3200x900. I run a VNC server on the laptop and connect to it (via SSH tunnel) from the desktop - when I press the full screen hot key, I get a 1600x900 view of the remote machine on one monitor, and half of my local desktop on the other monitor - the "full screen" only expands to fill one local monitor.
Normally this is exactly what you want when you full screen a web browser, email client, or other application. I'm sure there's some X magic to make it clear what a full screen actually entails, and the vnc client application is just dutifully accepting what it's told. While I would like to keep the normal full screen behavior for regular applications, but when I'm VNCing to another 3200x900 machine, I'd really like full screen to stretch across both local displays. Resizing the window to be "close" isn't quite good enough since I still have local panels at the top and bottom of one display (though I can set them to autohide), plus the VNC client application window border (since it doesn't appear to respect -notitle).
Is there any good way to have X lie to a single application about the "full screen" size? Can I get it to lie to all applications? xrandr --noprimary appears to have no effect.
I'm trying to get ubuntu working w/ 3 monitors. I have been given 2 video cards
lspci | grep VGA
20:01:00.0 VGA compatible controller: ATI Technologies Inc RV620 LE [Radeon HD 3450]
25:05:00.0 VGA compatible controller: nVidia Corporation NV44A [GeForce 6200] (rev a1)
I have had it working w/ two monitors plugged into the ATI correctly. and the nVidia monitor blank. Now I have the nVidia monitor working and one monitor from the ATI working, but I can't seem to get the last monitor to show anything. It does show the boot screen and works up until the point you are presented w/ the login screen for ubuntu, then it disappears and the nVidia monitor turns on. Might I have something wrong w/ my xorg.conf or do I need to do something more to get this to work? Currently I'm seeing this error in my Xorg.0.log file, but I'm not sure where to go from here:
[ 24.746] (EE) RADEON(2): reusing fd for second head
/etc/X11/xorg.conf
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 270.29 (buildmeister@swio-display-x86-rhel47-02.nvid
[code]....
I'm looking for virtual machine software that supports dual monitors on a Linux guest with a Windows 7 host.VirtualBox supports dual monitors only for Windows guests. VMware Player was extremely slow, so I gave up. I'm not sure it supports dual monitors, anyway. Can anyone recommend a product for what I want to do?
View 1 Replies View RelatedMy Dell Precision Workstation was shipped in 2003 with RH Linux installed (most likely RHEL 4) - though not sure.
At the time, the dual monitors worked by replacing the X86config file with one sent from Dell.
Since, my disk failed and I had to replace the disk and reinstall RH Linux with the shipped disks, RHEL 5.
Now, I can not find X86config; rather, I have been trying to update the Xorg.conf file with no to limited success.
Both monitors are driven off of one Nvidia Quadro FX 1300 videocard. My goal is to get the screen to span both.
Does anyone have a Xorg.conf file that would support this?
how is the support for multiple, two or more, monitors in ubuntu (10.04) when using a graphic cards from AMD(/ATI), for example the HD 5770. (Which I'm currently using). I know that DP is required to use three monitors on a regular card. But other than that, will it work? Am I to expect a lot of work to be able to get it working? Or will it simply be impossible? (And yes, I know that AMDs(/ATI) drivers aren't always the best... Although changing to a card from nvidia at this moment isn't possible)
The background to my question is that I'm thinking about buying another monitor, same model as the current one I'm using, and later on perhaps expand to buy another one.Tried to search for it but wasn't able to find how the support would be in linux, and ubuntu in particular, since most I found is about the windows support, which should work quite easy and therefore isn't relevant.
I want to be able to login on different users on my two screens. Is that possible? It would be nice if I could have the left screen and my gf could have the right. I'm using ubuntu 10.04 with gnome, and I have a Nvidia graphics card.
View 8 Replies View RelatedSo I'm using Lenny, trying to get dual monitors set up. I'm not sure on the correct steps, but have done some googlin' and wasn't finding what i was looking for. (could be that i just missed it)
lspci:
01:00.0 VGA compatible controller: ATI Technologies Inc RV516 [Radeon X1300/X1550 Series]
01:00.1 Display controller: ATI Technologies Inc RV516 [Radeon X1300 Pro] (Secondary)
I have a Dell inspiron 1525 laptop with a 1280x800 display and an external 1280x1024 monitor. I'm using 9.04 with openbox. I've done a loooot of online reading about how to get a dual monitor setup using xrandr, and I really don't know what I'm missing here. So here's the deal: I want to have my external monitor on the left of the laptop's display, and of course I want each of them to display different parts of the desktop.
First I set up the right resolution to each one of them (I do it using lxrandr). Typing xrandr -q in a terminal, I get the following:
[Code]...
I have an asus p5kpl-cm MB. I plugged in a radeon 9200 pci card. In the bios, I can set up:
pci/igd
igd/pci
igd
etc.
This determines which of the 2 displays (pci card or internal graphics on the MB) is the boot display. That determines which comes up with the bios screen and then once booted into ubuntu (10.04), this is the only adapter/monitor seen. The button detect monitors doesn't do anything.
lspci sees both my internal and pci card graphics. So, I can get either to work just fine (auto detected etc.) just not both at the same time.
I've tried all of the 3 above settings, and even when I set it to just igd, lspci still sees both my adapters. It identifies them correctly, and it works perfectly, detecting the monitor and knows the resolutions for each - just not both at the same time.
Does ubuntu know how to automatically configure more than one display w/o doing something else, or must I do something else to get both going together?
Code:
$ lspci
00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 10)
00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express Integrated Graphics Controller (rev 10)
[Code]....