After having solved my raid5 creation problems, I'm running into a new one: the RAID is just impossible to mount through fstab. I get a wonderful "The disk drive for /dev/md0 is not ready yet or not present.
Continue to wait or press S to skip mounting or M for mount recovery."
Once the system has booted, I can perfectly run a mount /dev/md0 /media/raid and mount it manually.
I've already tried mdadm.conf with UUIDs, with device names, tried several options in fstab, xfs and ext4 filesystems, nothing to do, it won't mount.
All this is running under Ubuntu 10.04 server, kernel: 2.6.32-25 server, mdadm 3.1.4 (from a Debian sid)
I am trying to setup fstab to automatically mount my NTFS partitions. I have used various Mount managers to create the entries in fstab. The fstab seems fine, but when mounting at boot or even via Nautilus I get the error message that I do not have permission to mount the disk.
1) Can this permission be set in the fstab file? If so what is the syntax of the fstab entry?
2) If not, is there a tool i.e. GUI to set the mount permissions?
I made a software RAID 0. It works fine, but when I add it to fstab and reboot the server, I can't restart the server. Code: # cat /etc/fstab LABEL=/ / ext3 defaults 1 1 LABEL=/boot /boot ext3 defaults 1 2 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 LABEL=SWAP-sda5 swap swap defaults 0 0 /dev/md0 /vz ext3 defaults 0 0
When I go to rescue mode and delete /dev/md0 from fstab, I can restart, but I get this when I try to mount it again: Code: mount: you must specify the filesystem type
So I try to make it to a ext3 Code: # mkfs.ext3 /dev/md0 mke2fs 1.39 (29-May-2006) mkfs.ext3: Device size reported to be zero. Invalid partition specified, or partition table wasn't reread after running fdisk, due to a modified partition being busy and in use. You may need to reboot to re-read your partition table. #fdisk /dev/md0 Unable to read /dev/md0
I used the usual 'mkfs.xfs -l size=128m,lazy-count=1 /dev/sdX' at creation. After that, I would like to use custom mount options like: This goes instead of the "defaults" part in /etc/fstab
I receive the following error at boot: INVALID log iosize 4 [not 12-30] << No one used iosize 4... what does it mean? it is connected to the options..but which one? (At the minute I'm usig it with: noatime,nobarrier).
I am writing this software that creates virtual block device nodes almost like loop does. I need to allow non-superusers to mount and umount filesystems from these devices. I don't know the names of the block device nodes beforehand so i can't use fstab entries to add "user" or "owner" flags there.
Currently i solve this by providing a small suid helper tool that verifies that this is indeed "my" block device the user is trying to mount and then just call /sbin/mount or /sbin/umount to do the job. This is definitely better than setting a suid bit for the whole program but not really perfect.
I've just started playing around with a Sheevaplug running a very light version of Ubuntu. I'm planning to run it with an SD card to store all my server data and a USB stick to regularly back up some of it.My problem is that the 2 partitions on my SD card mount fine at boot, but my USB stick's single partition does not. Could it be that the mounts specified in fstab are done before my USB device has finished getting alive? Mounting the USB stick manually works perfectly well.
Code: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver orion-ehci orion-ehci.0: Marvell Orion EHCI orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000 orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected Initializing USB Mass Storage driver.....
In the dmesg Code: usb-storage: device scan complete comes after
Code: EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended which makes me think the USB stick has missed the fstab train the 2 SD card partitions are on. And changing the order of the entries in fstab does not make any difference either.
I'm not planning to reboot my Sheevaplug every 5 minutes, but I like things to be nice and clean.
I can't remember if things with mounting vista/ntfs partitions has changed, but I cannot seem to get my partition mounted as a read-write partition.
I tried this in fstab:
And it made it read-only..
So i tried this:
And it wouldn't mount it.
Quote:
Failed to mount '/dev/sda1': Operation not supported Mount is denied because NTFS is marked to be in use. Choose one action:
Choice 1: If you have Windows then disconnect the external devices by clicking on the 'Safely Remove Hardware' icon in the Windows taskbar then shutdown Windows cleanly.
Choice 2: If you don't have Windows then you can use the 'force' option for your own responsibility. For example type on the command line:
Or add the option to the relevant row in the /etc/fstab file:/dev/sda1 /media/vista ntfs-3g force 0 0
I'm trying to get fstab to auto-mount a removable device when its plugged in? Is this possible and if not what is the easiest way to auto-mount a removable device?
I've accidentaly corrupted my fstab and cut the ends of lines. There are now disk uid, mount point, filesystem for root and swap, but the mount parameters are missing.The system boots as readonly. What are default fstab mount parameters in Debian for ext4 root and swap?
I'm running XBMC media center which is built on Ubuntu and I'm trying to mount a network share, but I can't seem to automate it. If I manually run:
Code:
mount -t cifs -o file_mode=0777,dir_mode=0777 //192.168.1.20/disk7/xbmc_thumbs/Thumbnails /home/kevin/.xbmc/userdata/Thumbnails
The mount is created and everything works fine. But obviously the mount eill be lost on the next boot. A few months back, when I was running a previous version of XBMC and first instructed on how to do this, I was told to put that command in /etc/init.d/rc.local so the mount would automatically be created at boot. I did and it worked. The other day I upgraded to a new XBMC build (which is built on the newer Lucid Ubuntu) and while the same command creates the mount, putting it in /etc/init.d/rc.local does not create it on boot. Someone suggested the fstab was the better place to create the mount. So I inserted the following in /etc/fstab:
Server: Ubuntu Server Edition 8.04 /currently firewalled to only allow client ip Client: Ubuntu Desktop 8.04 /currently firewalled to only allow server ip
Same userid and groups set up on on both. I have taken two linux courses and can maneuver around fairly well, but am still pretty newbie at all this. We have loaded Samba on a server and created a Samba share. I AM able to access that share via Windows Vista, but have not been able to successfully mount the share on the Ubuntu desktop via the fstab file. I have tried the following ways: serverip:/path/shareddirectory /net ext3 user,sync 0 0 and the samba way..
After modifying fstab, I reboot. No luck since that either way.Only ONCE after modifying it samba way, I was prompted to enter credentials, but after login I was unable to view the files on the server. From this point on either way, if I run commmand 'mount -a' the response is "Special device serverip:/path/sharedirectory does not exist" Also! I am able to ping client-to-server, but not server-to-client.
I'm using Kubuntu 9.10. Partitions get listed in the sidebar when I open the File Manager, but they don't get mounted under /media until I click on the entries. I do not want to use /etc/mtab and mount them under folders I create in /mnt; would prefer if there was a way to mount the partitions without Kubuntu waiting for me to click on the names.
I am using CentOS 5.5 OS. I already install ntfs-3g rpm, but I don't know the command to mount network NTFS drive. I also want to mount it on my fstab file, so whenever it reloads, it can automatically mount on the specific folder.
Although I can perfectly mount any usb device (stick or disc) as being root, as a user I am not allowed to perform any such action! I have modified the corresponding fstab entry to look like:
Code: usbfs /proc/bus/usb usbfs noauto,user 0 0 and I have also made sure that the user is a member of the disk group, but without any luck. My system is OpenSuSE 11.2 (with KDE 4.4, but the problem is the same regardless I am attempting to mount the usb device via the GUI or through the text (c/k)onsole).
I run a headless Ubuntu 8.04 server, which acts as a web, email and file server. I am sticking with 8.04 as it is a LTS release and will upgrade to the next LTS when it is released.
I have two external USB drives, that I need to mount at boot. I have been using /etc/fstab up until now, with the following entries:
Code:
However, as I gather from doing searches is quite common, occasionally I get an error during boot (causing the system to drop to a recovery shell) because the USB drives take time to wake up and the system hasn't found them by the time it reads /etc/fstab.
From doing searches, it seems there is nothing you can do to fstab to fix this, so you need to mount them using an rc.local script instead, using:
Code:
The problem is, as I have two USB drives, their /dev/sdxx location changes between boots. I thus want to use UUID codes as I do in fstab, however I haven't found anything about this.
Does anyone know how I can use the mount command and UUID to mount a drive in rc.local and what options I have to use the mount the drive with the same options that I am using in my fstab entry? Obvisouly, I can't refer back to fstab using the mount command, because then I will still get the boot error issue if they are listed in fstab. And there is no space internally for the USB drives as there is already two internal drives.
I'm dual booting with Windows 7 and would like to have my windows 7 user folder mount when I boot.
After some looking around I edited /etc/fstab to add the following line:
This works. But it mounts the windows partition from the root level. I'd like to just mount C:UsersFHSM (/Users/FSHM) to /mnt/windows.
I'm trying to get it so that when I click on the windows drive I get my windows user folder instead of having to click through from C: to get to it.
I'm the only user on this system but if I created a second windows user would my home folder mount for that person too or does setting the user ID prevent that from happening?
I have installed a cable that connects from the CPU's SATA motherboard connection to a removable drives' ESATA connection.I would like to be able to swap drives on the ESATA connection and have all users be able to read and write to these drives.I have created the directory /archive/ where I would like the drive(s) to mount.The drives are all formatted Fat 32 - but in the future I may use HFS for formatting.When I used the command (as root):mount /dev/sdc1 /archivethe drive was mounted (but read only)What can I use in my /etc/fstab file that will allow drives to be mounted and unmounted by all users on the system? (both reading and writing)Also, will I be able to mount and unmount these drives without shutting down? or will I need to reboot every time I want to change drives?
I have a CentOS 5 production server with multiple OS-managed RAID-1 sets. I'd like to add a new mirrored set and move the /var partition to the new drives. On a non-RAID system I would boot from the install CD to edit fstab and copy the existing files to the new drive, but I'm pretty sure booting off the install CD does not recognize my RAID setup.
I have been battering with FC10 and software RAID for a while now, and hopefully I will have a full working system soon. Basically, I tried using the F10 live CD to setup Software RAID 1 between 1 hard drives for redundancy (I know its not hardware raid but budget is tight) with the following table;
[Code]....
I set these up by using the RAID button on the partition section of the install except swap, which I set-up using the New partition button, created 1 swap partition on each hard drive that didn't take part in RAID. Almost every time I tried to do this install, it halted due to an error with one of the raid partitions and exited the installer. I actually managed it once, in about...ooo 10-15 times of trying but I broke it. After getting very frustrated I decided to build it using just 3 partitions
[Code]....
I left the rest un-touched. This worked fine after completing the install and setting up grub, reboot in to the install. I then installed gparted and cut the drive up further to finish my table on both hard drives. I then used mdadm --create...etc to create my RAID partitions. So I now have
I need to copy data from a single HD, which used to be part of a Linux RAID 1. I've googled around, but can't find any clue how to mount partitions from this single HD.
Background: The HD comes from a linux based NAS box Synology DS207+. The NAS uses ext3 as filesystem. Both NAS disks are fine, but the other NAS hardware is dead and not worth repairing or replacing.
I'm really tired of having to umount under root, then mount again as a user for my external hard disk. When I'm in firefox, I like to save pages alot onto my external but I constantly have to remount because my user has no write permissions for the drive. What can I do for my device in fstab so that it mounts automatically under my user and not root?
I have a router that supports NAS; that is, you can plug a USB drive directly into the router, and it becomes a Windows share. I can manually mount the NAS share and use it properly. But, I would like to have it automatically mount on startup. The main reason for this is to assign it a proper mount point so that I can access it from the command line, since I'm having trouble doing that after I mount it manually.
To mount it manually, I go to Places > Connect to Server, select the "Windows Share" service type, and enter "//192.168.1.1/USB_Storage" as the server name. The server name is supposed to be "//readyshare/USB_Storage," but that does not work, so I used the IP address.
I would like to mount this drive at /mnt/readyshare. So, I followed (I thought) the instruction in this document. I created the directory /mnt/readyshare I assigned myself a samba password with smbpsswd I created a group "readyshare" with the GID 1010 I created a .smbcredentials file in my home directory I modified my /etc/fstab file.The .smbcredentials file reads:
Code:
username=<my username> password=<the password I created with smbpsswd
I can access the files I need by using the telnet command, but I need to have access to the files in my local file system. Is it possible to mount a shared drive over telnet in the fstab file?
On my Suse 11.1 computer, I'm only able to run 'mount' as root, but this screws up the permissions somehow, in that my external drives are now read only when I am normal user. I can plug my external drives to my mac osx laptop via usb or firewire, and I can read,write, and execute. As su, I can mount the drives using usb on my suse computer, but only as read only.
Optimally, I want to edit the fstab file to auto mount these external drives, and then have samba run to make the drives available (i.e. rw) on laptop.
NOTE: 1. I created the file systems on a laptop (mac osx) which has different user name than my suse 11.1 computer.
2. I tried to use chown to manually force user:group to be Mike:users instead of root:root, but the external drives still are 'read only.' Trying different options in column 4 fstab file kept giving same trouble, but I can now get user:group = 99: 99 (not sure what that means).
I cant mount a directory on red hat 5 from red hat 4 using fstab.I keep getting permission denied.I mount directories on the same red hat 5 sys from other red hat 5 and 2 old HPUX systems using fstab.When I try to telnet to it i get "no route to host."
