General :: XFS Won't Mount With Fstab Options In Fedora 12
Feb 6, 2010
I used the usual 'mkfs.xfs -l size=128m,lazy-count=1 /dev/sdX' at creation. After that, I would like to use custom mount options like: This goes instead of the "defaults" part in /etc/fstab
I receive the following error at boot: INVALID log iosize 4 [not 12-30] << No one used iosize 4... what does it mean? it is connected to the options..but which one? (At the minute I'm usig it with: noatime,nobarrier).
I am trying to setup fstab to automatically mount my NTFS partitions. I have used various Mount managers to create the entries in fstab. The fstab seems fine, but when mounting at boot or even via Nautilus I get the error message that I do not have permission to mount the disk.
1) Can this permission be set in the fstab file? If so what is the syntax of the fstab entry?
2) If not, is there a tool i.e. GUI to set the mount permissions?
I can access the files I need by using the telnet command, but I need to have access to the files in my local file system. Is it possible to mount a shared drive over telnet in the fstab file?
I have been trying to work out how to set up Fedora 15 to automatically mount an NFS share at boot time. I can mount the share interactively using 'mount -t nfs server:/usr/local /usr/local'. When I put the entry in /etc/fstab, it stops the machine booting. It tries to give me a shell ('Enter root password for shell or press Control-D to exit') or something close to that. However, I cannot enter the maintenance mode, it hangs. Same thing with pressing control-D, it hangs and doesn't get any further.
I rescued the system by booting off a CD, mounting root, and removing the nfs entry from fstab. After that it booted fine. The entry I had in the fstab is: nfsserver:usr/local /usr/localnfsro,hard,bg,intr,comment=systemd.automount0 0
I put the 'comment=systemd.automount' entry in because of some related searches I did in forums.
I have two mount points that used to work. I have them defined as cifs shares in fstab, and they map to a Windows machine, which I am able to ping from my Fedora machine, but for some reason I get a mount error 2, and the destination is not accessible. The man page doesn't really give any troubleshooting steps. Since I am mounting by IP address (which as I said has worked before), nothing has changed, although the IP address did change, which I updated in the fstab file to the new IP address (and since I have reserved this new IP address so it can't change again!)
I ran a test and shared a folder from another one of my computers, and added a line in fstab to auto-mount that, and I get a "permission denied" error 13, which is different than the error 2 I get on the other 2 shares. What should I be looking for as far as actual connectivity between the machines? I have verified that the windows machine is on and I can access the same shares from another computer.
Update: Added the host and IP address to my hosts file, and replaced the IP address with the name, and still get the same error. Also, the share name has a space in it, so I replace that with a "�40" space character (which worked in the past). I tried replacing that with an actual space, and putting quotes around the URL, but then I get a "bad URL" error.
I am writing this software that creates virtual block device nodes almost like loop does. I need to allow non-superusers to mount and umount filesystems from these devices. I don't know the names of the block device nodes beforehand so i can't use fstab entries to add "user" or "owner" flags there.
Currently i solve this by providing a small suid helper tool that verifies that this is indeed "my" block device the user is trying to mount and then just call /sbin/mount or /sbin/umount to do the job. This is definitely better than setting a suid bit for the whole program but not really perfect.
After having solved my raid5 creation problems, I'm running into a new one: the RAID is just impossible to mount through fstab. I get a wonderful "The disk drive for /dev/md0 is not ready yet or not present. Continue to wait or press S to skip mounting or M for mount recovery."
Once the system has booted, I can perfectly run a mount /dev/md0 /media/raid and mount it manually. I've already tried mdadm.conf with UUIDs, with device names, tried several options in fstab, xfs and ext4 filesystems, nothing to do, it won't mount.
All this is running under Ubuntu 10.04 server, kernel: 2.6.32-25 server, mdadm 3.1.4 (from a Debian sid)
I've just started playing around with a Sheevaplug running a very light version of Ubuntu. I'm planning to run it with an SD card to store all my server data and a USB stick to regularly back up some of it.My problem is that the 2 partitions on my SD card mount fine at boot, but my USB stick's single partition does not. Could it be that the mounts specified in fstab are done before my USB device has finished getting alive? Mounting the USB stick manually works perfectly well.
Code: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver orion-ehci orion-ehci.0: Marvell Orion EHCI orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000 orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected Initializing USB Mass Storage driver.....
In the dmesg Code: usb-storage: device scan complete comes after
Code: EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended which makes me think the USB stick has missed the fstab train the 2 SD card partitions are on. And changing the order of the entries in fstab does not make any difference either.
I'm not planning to reboot my Sheevaplug every 5 minutes, but I like things to be nice and clean.
I can't remember if things with mounting vista/ntfs partitions has changed, but I cannot seem to get my partition mounted as a read-write partition.
I tried this in fstab:
And it made it read-only..
So i tried this:
And it wouldn't mount it.
Quote:
Failed to mount '/dev/sda1': Operation not supported Mount is denied because NTFS is marked to be in use. Choose one action:
Choice 1: If you have Windows then disconnect the external devices by clicking on the 'Safely Remove Hardware' icon in the Windows taskbar then shutdown Windows cleanly.
Choice 2: If you don't have Windows then you can use the 'force' option for your own responsibility. For example type on the command line:
Or add the option to the relevant row in the /etc/fstab file:/dev/sda1 /media/vista ntfs-3g force 0 0
I'm trying to get fstab to auto-mount a removable device when its plugged in? Is this possible and if not what is the easiest way to auto-mount a removable device?
I've accidentaly corrupted my fstab and cut the ends of lines. There are now disk uid, mount point, filesystem for root and swap, but the mount parameters are missing.The system boots as readonly. What are default fstab mount parameters in Debian for ext4 root and swap?
I'm running XBMC media center which is built on Ubuntu and I'm trying to mount a network share, but I can't seem to automate it. If I manually run:
Code:
mount -t cifs -o file_mode=0777,dir_mode=0777 //192.168.1.20/disk7/xbmc_thumbs/Thumbnails /home/kevin/.xbmc/userdata/Thumbnails
The mount is created and everything works fine. But obviously the mount eill be lost on the next boot. A few months back, when I was running a previous version of XBMC and first instructed on how to do this, I was told to put that command in /etc/init.d/rc.local so the mount would automatically be created at boot. I did and it worked. The other day I upgraded to a new XBMC build (which is built on the newer Lucid Ubuntu) and while the same command creates the mount, putting it in /etc/init.d/rc.local does not create it on boot. Someone suggested the fstab was the better place to create the mount. So I inserted the following in /etc/fstab:
Server: Ubuntu Server Edition 8.04 /currently firewalled to only allow client ip Client: Ubuntu Desktop 8.04 /currently firewalled to only allow server ip
Same userid and groups set up on on both. I have taken two linux courses and can maneuver around fairly well, but am still pretty newbie at all this. We have loaded Samba on a server and created a Samba share. I AM able to access that share via Windows Vista, but have not been able to successfully mount the share on the Ubuntu desktop via the fstab file. I have tried the following ways: serverip:/path/shareddirectory /net ext3 user,sync 0 0 and the samba way..
After modifying fstab, I reboot. No luck since that either way.Only ONCE after modifying it samba way, I was prompted to enter credentials, but after login I was unable to view the files on the server. From this point on either way, if I run commmand 'mount -a' the response is "Special device serverip:/path/sharedirectory does not exist" Also! I am able to ping client-to-server, but not server-to-client.
- replace my hard drive with a 32GB SSD (solid state drive) SATA-II - copy my entire old drive to the new one - Both my drives will be Ext3 and have no swap (I have lots of RAM)
1. Can a Debian lenny desktop boot from an SSD ? 2. Do I have to modify /etc/fstab with SSD-specific options ? 3. How about grub, any modifications ?
Our office just switched from CentOs to Fedora and I'm trying to get everything set up. Everything is working so farbut im having a problem with my mounted cifs drives. They mount ok, I made directories in /mnt where the drives are readable and accessible. I'm only missing the shortcuts to the mounted drives in nautilus and on the desktop. I've checked the gconf editor and the volumes should be visible.Is there an extra option i have to add in the fstab line to get the shortcuts or something like that?
I am trying to mount a directory from my server onto my wireless laptop. The directory mounts successfully if I am already logged into the laptop with another account first but if I log on initially with the user who requires the mount the mount fails. I suspect the mount is taking place before my network connection is up, is it possible therefore, to delay the mount in fstab until the network is fully connected?
I'm using Kubuntu 9.10. Partitions get listed in the sidebar when I open the File Manager, but they don't get mounted under /media until I click on the entries. I do not want to use /etc/mtab and mount them under folders I create in /mnt; would prefer if there was a way to mount the partitions without Kubuntu waiting for me to click on the names.
I am using CentOS 5.5 OS. I already install ntfs-3g rpm, but I don't know the command to mount network NTFS drive. I also want to mount it on my fstab file, so whenever it reloads, it can automatically mount on the specific folder.
Gateway m275 laptop with builtin smartcard reader. I've done modeprobe - <mmc module of all types> after having removed modprobe.conf file. I see that there is a pcmcia rules, Do I add all modules to this list so hat it can be probed. Once pccardctl is working, how do I find the volume and mountit or set fstab to create the mount point or to have it automatically mounted in media.
I run a headless Ubuntu 8.04 server, which acts as a web, email and file server. I am sticking with 8.04 as it is a LTS release and will upgrade to the next LTS when it is released.
I have two external USB drives, that I need to mount at boot. I have been using /etc/fstab up until now, with the following entries:
Code:
However, as I gather from doing searches is quite common, occasionally I get an error during boot (causing the system to drop to a recovery shell) because the USB drives take time to wake up and the system hasn't found them by the time it reads /etc/fstab.
From doing searches, it seems there is nothing you can do to fstab to fix this, so you need to mount them using an rc.local script instead, using:
Code:
The problem is, as I have two USB drives, their /dev/sdxx location changes between boots. I thus want to use UUID codes as I do in fstab, however I haven't found anything about this.
Does anyone know how I can use the mount command and UUID to mount a drive in rc.local and what options I have to use the mount the drive with the same options that I am using in my fstab entry? Obvisouly, I can't refer back to fstab using the mount command, because then I will still get the boot error issue if they are listed in fstab. And there is no space internally for the USB drives as there is already two internal drives.
I'm dual booting with Windows 7 and would like to have my windows 7 user folder mount when I boot.
After some looking around I edited /etc/fstab to add the following line:
This works. But it mounts the windows partition from the root level. I'd like to just mount C:UsersFHSM (/Users/FSHM) to /mnt/windows.
I'm trying to get it so that when I click on the windows drive I get my windows user folder instead of having to click through from C: to get to it.
I'm the only user on this system but if I created a second windows user would my home folder mount for that person too or does setting the user ID prevent that from happening?
all of a sudden my pc decided no to start anymore.YOu might be aware of the ide/sata driver problem, well it was the problem. I reinstalled grub with suse dvd and it went ok. Pc working properly. But then i tried to fix this once for all and changed the fstab options from /dev-by-id to uuid (all partitions : swap, /, /home etc ).Is uuid a definite solution ?Why is the pc not able to start from there ?
Since i moved the partitions with uuid option in fstab and even after reinstalling grub the pc is not starting anymore . It gives me the boot menu (linux suse/failsafe) and then a black screen left with no keyboard nor mouse available.
I have two NTFS volumes I want to automount at boot. I can't get my user account to mount them in Fedora 10. I keep getting the message that the two lines I have edited in fstab are bad. The volumes are sda2 and sda8, and the volume names are SPACELAB and Spaceman. I also need to be able to mount an NTFS usb drive from time to time. I am getting frustrated, so I have posted my fstab file below,
# # /etc/fstab # Created by anaconda on Sun Mar 1 12:44:11 2009 #
With a 1Tb USB drive plugged in, we'll call it "TheDrive", I boot my machine and "TheDrive" is mounted automatically. The icon is on the desk-top. "TheDrive" mounts to /media/TheDrive. Everything is fine. But, I would like to automatically mount the drive in my file tree at the location /mnt/TheDrive. I would not like to have the drive automatically mounted to /media/ and appear on the desktop. I know that this requires the use of fstab; but, I do not know what to add to this file.
I have a second hard drive with fedora 10 installed on it. My primary drive and os is fedora 12. How do I edit the fstab file in order to mount the second hard drive and get files off of it
I was wondering how to check the current mount options of my ext4 filesystems in Fedora 12? The only thing I can see in fstab is "defaults" but how can I know what is behind those defaults.mount command only shows "/dev/sda6 on / type ext4 (rw) but nothing else.I'd like to know a few more things like the data mode used like "ordered" or "journal".
I have a 2 TB hard drive in an external USB caddy that I use for backups. The drive gets automatically mounted when connected to F13, which is great, and the default mount options it uses are:Code:rw,nosuid,nodev,uhelper=udisksHowever, I want to add an extra option or two but I don't know where I can do this. Does anyone know where I can add mount options onto the default set?
