I am looking for a 802.11n wireless card that Linux supports that can be dropped into AP/master mode.
I would prefer PCI, but USB would be tolerable, just not preferred.
I am running ubuntu 9.04 in my laptop. I want to change the wireless card mode of my laptop to master mode so that it can work like a access point.
View 1 Replies View RelatedI am using ubuntu 9.10 on my desktop having a belkin wireless usb card. I want to change the mode of it to master mode. How can I do it?
View 3 Replies View RelatedI'm looking for a USB wifi which supports master mode, 11n modulation, 5GHz band (with master and ad-hoc support for this band) and has detachable antenna connector.
View 1 Replies View RelatedI have a cheapo Nvidea motherboard and an ATI 5700 graphics card. I wanted to know if there is a simple way to ensure that OS11.3 is using the ATI graphics card and radeonhd drivers instead of the Nvidea hareware+drivers. Is it necessary to blacklist the Nvidea drivers? Is there a simple YAST fix?
View 3 Replies View RelatedAnybody have any idea that how to set the ath9k in master mode in fedora 11. I am unable to set the same.
I am using the D-Link DWA556 card using the kernel built in ath9k.Find below the output I got while setting up it in master mode sudo iwconfig wlan0 mode master.Error for wireless request "Set Mode" (8B06):SET failed on device wlan0 ; Invalid argument.Does that mean that master mode is not supported?Also Want the information if there is any separate community or development group for ath9k development and download the source of same except linuxwireless.com.
Code:
root@Atlantis:~# iwconfig wlan0 mode master
Error for wireless request "Set Mode" (8B06) :
SET failed on device wlan0 ; Invalid argument.
root@Atlantis:~# iwconfig wlan1 mode master
Error for wireless request "Set Mode" (8B06) :
SET failed on device wlan1 ; Invalid argument.
All other modes except secondary work fine.
The wireless cards are both PCI, a Netgear WG311v1 and a Linksys WMP54Gv4.1, though I'm not sure which is which.
When I try to set my Realtek Semiconductor Corp. RTL8187 Wireless Adapter to master mode I get the following error.
Code:
$ sudo iwconfig wlan0 mode master
Error for wireless request "Set Mode" (8B06) :
SET failed on device wlan0 ; Invalid argument. Is this the result of a driver or hardware incapability?
I am trying to get my wireless card working in master mode. I am running Jaunty server 2.6.28-11 x86_64. I have compiled hostapd with nl80211 enabled. The interface is using ath9k. I have tried to compile compat-wireless with this patch. However IEEE80211_IF_TYPE_AP was undefined along with IEEE80211_IF_TYPE_VLAN. In addition the latest version of compat-wireless needs to be patched for kernels < 2.6.31 with this. However when using this patch IRQ_WAKE_THREAD is still undefined.
I have got to this message:
Code:
$ sudo hostapd /home/jophish/.hostapd.conf
Configuration file: /home/jophish/.hostapd.conf
Failed to set interface wlan0 to master mode.
[code].....
I'm looking for a USB adapter with driver support for running the interface in master mode.
View 1 Replies View Relatedi am wanting to turn my Debian box into a wireless AP, but for some unknown reason the wireless card won't switch into master mode when i run the command #iwconfig wlan1 mode master i get this Error for wireless request "Set Mode" (8B06): SET failed on device wlan1 ; Invalid argument. what does this mean and what do i need to configure/install to get it to work my wirless card is supported i checked it's a zydas chipset using the zd1211rw driver SMC EZ Connect SMCWUSB-G [URL]
View 14 Replies View Relatedafter trying several pci and usb network cards none were able to have their ssid broadcasted. The question that i have is: Can a suse box be converted to act as an acces point without the use of atheros based hardware, without switching over to ubuntu and or debian, without the use of openwrt?
View 4 Replies View RelatedI'm running Ubuntu 10.10 and try to get my wifi to work in master mode. The dongle is a Asus 167g v3 and I'm using the rtl8192SU driver. I can connect to a network or put the dongle in Ad-hoc mode without a problem. It's when I try to put in master mode some problem occurs. When I do:
Code:
sudo iwconfig wlan1 essid test mode master
This is the output I'm getting:
Code:
wlan1 unassociated Nickname:"rtl_wifi"
Mode:Master Access Point: Not-Associated Sensitivity:0/0
[Code].....
The dongle is in master mode but it fails to assign a SSID. I also tried to set it up in /etc/network/interfaces but the result is always the same... No SSID
I try to set-up an Access point using ubuntu 11.04. I am using the minimal configuration file from [URL] together with a TP-Link TL-WN422G (Atheros chipset). I've installed the linux-backports-net-natty-generic drivers. But when trying to start hostapd I always get this output:
Code:
# hostapd -dd -K test.conf
Configuration file: test.conf
Failed to set interface wlan0 to master mode.
nl80211 driver initialization failed.
wlan0: Unable to setup interface.
ELOOP: remaining socket: sock=5 eloop_data=0x9b9440 user_data=(nil) handler=0x43d980
I have also disabled the network-manager for this device by adding this to /etc/network/interfaces:
Code:
iface wlan0 inet manual
cat test.conf:
Code:
interface=wlan0
driver=nl80211
ssid=test
channel=1
lsusb says:
Code:
...
Bus 001 Device 005: ID 0cf3:1006 Atheros Communications, Inc. TP-Link TL-WN422G v2 802.11g [Atheros AR9271]
...
lsmo: .....
Code:
Linux magnet 2.6.38-8-generic #42-Ubuntu SMP Mon Apr 11 03:31:24 UTC 2011 x86_64 x86_64 x86_64 GNU/Linux
I've searched for too many days and nights so many information went through my head. I want to buy a usb wireless which support master mode. (not monitor mode) Now I'm interested in Alfa AWUS036NEH. I like it because it is small an have a long antenna strong 1000mW. signal. (AWUS036H is a little bit big for me) However from what i have read AWUS036NEH is not supported in master mode (softAP)(or may be supported but with hostapd, but again some forum said it doesn't support and some say it does... Totally confused.) -> Actually AWUS036NEH is not expensive but I don't want to invest in something i'm not sure about so I won't buy it until I really know if it works. So I switch to find out what is for sure
1. supported in master mode in Ubuntu
2. Have a long antenna (like 5" or something. I have no idea about hardware but I think longer antenna should send signal more further)
3. small (about normal USB size don't count antenna)
Sadly I only find Alfa AWUS036NEH the only option for me , the others has no brand. However TL-WN722N is what most likely to fit. Only it has a shorter antenna. Can i replace the antenna with a longer one (with some others brand) by myself? (TL-WN722N can use master mode in kernel 3.0 ? already ? some say it should but i've not seen one that stated clearly) Ahh I think the above is totally messed up. I will make long story short.
1. Is AWUS036H or AWUS036NEH support master mode in ubuntu ? (if yes with hostapd or something?)
2. Is TL-WN722N or TL-WN722NC can work in master mode in Ubuntu ? (if yes with hostapd or something?)
3.Can I replace the original antenna with a longer one ?(with other brand or same brand) Will the signal be stronger?
I got two issues with my wifi usb adapter:
1) it cannot see any networks around
2) i cannot setup it in master mode to use my PC as a router
As far as i can see, the device is recognized and the correct driver (rt73usb) is loaded. I was able to connect to a laptop somehow (the laptop could see other networks and the adapter's PC-to-PC network). I'd like to make it work as a router, i.e. share my internet connection (eth0) via wlan0. Here is what i have:
Code:
Ubuntu 10.04
Linux 2.6.32-22-generic #36-Ubuntu SMP Thu Jun 3 19:31:57 UTC 2010 x86_64 GNU/Linux
TP-Link TL-WN321G wifi usb adapter as seen as
Bus 001 Device 006: ID 148f:2573 Ralink Technology, Corp. RT2501USB Wireless Adapter
$ iwconfig wlan0
wlan0 IEEE 802.11bg ESSID:off/any
[Code]....
i try to install my d-link dwl-g520 h/w:A1 in master mode with madwifi drivers but:
$ lshw
*-network:1
description: Wireless interface
product: Atheros AR5001X+ Wireless Network Adapter
vendor: Atheros Communications Inc.
physical id: 5
bus info: pci@0000:00:05.0
[Code]...
after successfully configuring the dwa-552 to work in master mode in ubuntu 10.04 (ath9k driver) I ran some file transfer tests. The download speed is very good (~50mbps) but the upload speed spikes at about 10-20mbps for the first few KB and then it's nonexistent (0-1kbps). This only affects file transfers or otherwise bandwidth consuming processes. Normal web browsing or ssh is not affected. After running a speedtest of my internet connection which is routed through the AP I could upload to the internet with 1mbps which is my inet connection maximum so apparently this is not affected. Tried the same file transfers with netcat to eliminate any other factors and had the same problem. dmesg and hostapd debug did not report anything unusual
View 2 Replies View RelatedI want to monitor network traffic with ntop from a Lucid 10.04 machine. Both NICs have picked up an IP address, I need to put one in promiscuous mode. I typed sudo ifconfig eth1 promisc and the response was SIOCSIFFLAGS: Permission denied.I also tried sudo su ifconfig eth1 promisc[sudo] password for user1: I put it in Unknown id: ifconfig
View 3 Replies View RelatedI'm managing a residential network. Each flat is its own subnet, and can only communicate with the other flats through a router (i.e. no broadcast). 95% of these 300 subnets only contains windows computers (from lambda users).
My final goal is to be able to browse the entire network from any computer.
I set up a samba server acting as a wins server, and every computer is aware of it because it is registered in the dhcp. So name resolution is working fine for everyone.
The same samba server is set to be the "Domain master browser":
workgroup = WORKGROUP
wins support = yes
prefered master = yes
local master = yes
domain master = yes
os level = 65
When I browse the network (using "net view" or "browstat view"), I can only see the servers which are in the same subnet as the domain master browser.
Now, when in a subnet the computers arrange themselves to find a "local master browser", the only visible computers are the one in that subnet.
What I don't understand is why all the local masters don't synchronize their lists with the domain master.
So, to sum up, every subnet get the following behaviour:
-if a local master is elected, the only visible computers are the one in the same subnet.
-if no local master is elected, the only visible computers are the one in the subnet of the domain master.
-if I add another samba, configured as a local master winning all elections, then the magic is working and the lists are synchronized.
What is expected:
-every computer can see all the computer from all the subnets.
I'm looking at buying one of the above cards, and was wondering if anyone knew if they worked in master mode (e.g. as an access point). According to the Aircrack-ng site, they support packet injection and monitor mode. Is master mode support solely up to the driver used with the card, or does the card have to physically support it?
View 2 Replies View RelatedI am using ubuntu 10.04.My samsung e2120 has external micro sd card of 2GB.When i connect mobile to computer via cable in windows , it works normal as USB mass storage as configured by me in mobile settings.But in case of ubuntu 10.04
Code:
$cp /data/to send/khatarnak shayri.txt /media/E0FD-1813/
cp: cannot create regular file `/media/E0FD-1813/khatarnak shayri.txt': Read-only file system
[code].....
Below is a print out of my partition Table from Fdisk, in Cylinder mode, Sector mode, and then in expert mode?
Why in expert mode does it look like Partitions 2 and 3 share the same sector / hd / Cylinders? Is this OK?
Code:
I'm looking into assembling a debian based router/firewall system. Fortunately there is a great deal of documentation available on this subject, so I am confident the project is viable. I'm a bit stumped regarding a wireless card though, especially since I'd like to use a desktop form factor rather than one of the laptop style slots. At present, I'm going with a mini-itx board that has a couple of wired nics and a pci-e x4 expansion slot (supermicro's x7spa-h). So, I can connect an access point to one of the nics and that's job done. In the interests of having one fewer box to find space for, I'd like to use a pci-e card as a (wireless n) access point. To do this I need one capable of working as a "master", rather than only as a "client".
Google suggested D-link's dwa-556. Linuxwireless.org suggests the D-link DWA-556 uses ath9k. It also thinks the ath9k driver is capable of operating as an access point. Can I take this to mean that the DWA-556 will be usable as an access point? If so, all is well, and I may go forth and find any card that uses a driver marked AP capable. If not, say because it's a hardware limitation, how do I go about finding a card that'll do what I want it to?
What is your preferred command for shutting down the system? Please explain your votes.
View 14 Replies View RelatedSo I noticed while using guided partitioning that most distro installers will attempt to create a logical partition for the root file system besides the swap and /boot on the HDD. Why is this the case? Why does the partition for root file system have to be logical and not primary?
View 10 Replies View RelatedI have a load balancer with 2 web servers behind it. The web servers rsync with cloud storage to update their apache directories 1 time every hour. Apache is just running php pages that pull/push data to a DB so they dont need to be updated that often. However I need to figure out how to implement a Master/Master MySQL setup to have my web servers point to for the PHP stuff. I need to implement it without having a single point of failure. The Load balancers are useless for failover as they only detect availability based on Ping request. So putting a master/master setup behind a Load Balancer is out. what is the best way to setup the master/master mysql in a HA setup without the use of a load balancer provided by the host?
View 2 Replies View RelatedMy linux workstation recently crashed. After rebooting, Linux (Red Hat 5.3) will not boot properly and automatically went into emergency mode or recovery mode i think. I can still see my /home/user/ and all the files inside.I boot from CD to rescue mode and tried mounting read-only the /dev/sd5 which contains the files in the crashed hard disk to try to copy out my files but mounting was unsuccessful (invalid argument). I checked the filesystem type using fsck -N /dev/sda5 and shows it to ext2. i tried to mount another known working hdd and was successful.
My question is why in emergency mode, the crashed hdd is able to be mounted automatically as read-only but cannot be done in rescue mode thru a bootable CD?Is there any special mount options used in emergency mode?I also cannot copy out in emergency mode booting from the crashed hard disk as everything is read only.
I want to back up the master boot on my hard drive, in case something screws it up. What software do you recommend for this?
My first idea is to boot from a Linux CD and dd the first 512 bytes of /dev/sda, and dd it back to recover. Will this solution work, and is it safe?
I came across Linux in university syllabus and quite loved it.Hope I will get to learn here Linux. How to become master in Linux can some body suggest some fast ways to do the same?I want to learn Linux Very fast.
View 14 Replies View Related