When I try to set my Realtek Semiconductor Corp. RTL8187 Wireless Adapter to master mode I get the following error.
Code:
$ sudo iwconfig wlan0 mode master
Error for wireless request "Set Mode" (8B06) :
SET failed on device wlan0 ; Invalid argument. Is this the result of a driver or hardware incapability?
Code:
root@Atlantis:~# iwconfig wlan0 mode master
Error for wireless request "Set Mode" (8B06) :
SET failed on device wlan0 ; Invalid argument.
root@Atlantis:~# iwconfig wlan1 mode master
Error for wireless request "Set Mode" (8B06) :
SET failed on device wlan1 ; Invalid argument.
All other modes except secondary work fine.
The wireless cards are both PCI, a Netgear WG311v1 and a Linksys WMP54Gv4.1, though I'm not sure which is which.
Anybody have any idea that how to set the ath9k in master mode in fedora 11. I am unable to set the same.
I am using the D-Link DWA556 card using the kernel built in ath9k.Find below the output I got while setting up it in master mode sudo iwconfig wlan0 mode master.Error for wireless request "Set Mode" (8B06):SET failed on device wlan0 ; Invalid argument.Does that mean that master mode is not supported?Also Want the information if there is any separate community or development group for ath9k development and download the source of same except linuxwireless.com.
I am running ubuntu 9.04 in my laptop. I want to change the wireless card mode of my laptop to master mode so that it can work like a access point.
View 1 Replies View RelatedI am using ubuntu 9.10 on my desktop having a belkin wireless usb card. I want to change the mode of it to master mode. How can I do it?
View 3 Replies View RelatedI'm running Ubuntu 10.10 and try to get my wifi to work in master mode. The dongle is a Asus 167g v3 and I'm using the rtl8192SU driver. I can connect to a network or put the dongle in Ad-hoc mode without a problem. It's when I try to put in master mode some problem occurs. When I do:
Code:
sudo iwconfig wlan1 essid test mode master
This is the output I'm getting:
Code:
wlan1 unassociated Nickname:"rtl_wifi"
Mode:Master Access Point: Not-Associated Sensitivity:0/0
[Code].....
The dongle is in master mode but it fails to assign a SSID. I also tried to set it up in /etc/network/interfaces but the result is always the same... No SSID
I am trying to get my wireless card working in master mode. I am running Jaunty server 2.6.28-11 x86_64. I have compiled hostapd with nl80211 enabled. The interface is using ath9k. I have tried to compile compat-wireless with this patch. However IEEE80211_IF_TYPE_AP was undefined along with IEEE80211_IF_TYPE_VLAN. In addition the latest version of compat-wireless needs to be patched for kernels < 2.6.31 with this. However when using this patch IRQ_WAKE_THREAD is still undefined.
I have got to this message:
Code:
$ sudo hostapd /home/jophish/.hostapd.conf
Configuration file: /home/jophish/.hostapd.conf
Failed to set interface wlan0 to master mode.
[code].....
I'm looking for a USB adapter with driver support for running the interface in master mode.
View 1 Replies View RelatedI try to set-up an Access point using ubuntu 11.04. I am using the minimal configuration file from [URL] together with a TP-Link TL-WN422G (Atheros chipset). I've installed the linux-backports-net-natty-generic drivers. But when trying to start hostapd I always get this output:
Code:
# hostapd -dd -K test.conf
Configuration file: test.conf
Failed to set interface wlan0 to master mode.
nl80211 driver initialization failed.
wlan0: Unable to setup interface.
ELOOP: remaining socket: sock=5 eloop_data=0x9b9440 user_data=(nil) handler=0x43d980
I have also disabled the network-manager for this device by adding this to /etc/network/interfaces:
Code:
iface wlan0 inet manual
cat test.conf:
Code:
interface=wlan0
driver=nl80211
ssid=test
channel=1
lsusb says:
Code:
...
Bus 001 Device 005: ID 0cf3:1006 Atheros Communications, Inc. TP-Link TL-WN422G v2 802.11g [Atheros AR9271]
...
lsmo: .....
Code:
Linux magnet 2.6.38-8-generic #42-Ubuntu SMP Mon Apr 11 03:31:24 UTC 2011 x86_64 x86_64 x86_64 GNU/Linux
I've searched for too many days and nights so many information went through my head. I want to buy a usb wireless which support master mode. (not monitor mode) Now I'm interested in Alfa AWUS036NEH. I like it because it is small an have a long antenna strong 1000mW. signal. (AWUS036H is a little bit big for me) However from what i have read AWUS036NEH is not supported in master mode (softAP)(or may be supported but with hostapd, but again some forum said it doesn't support and some say it does... Totally confused.) -> Actually AWUS036NEH is not expensive but I don't want to invest in something i'm not sure about so I won't buy it until I really know if it works. So I switch to find out what is for sure
1. supported in master mode in Ubuntu
2. Have a long antenna (like 5" or something. I have no idea about hardware but I think longer antenna should send signal more further)
3. small (about normal USB size don't count antenna)
Sadly I only find Alfa AWUS036NEH the only option for me , the others has no brand. However TL-WN722N is what most likely to fit. Only it has a shorter antenna. Can i replace the antenna with a longer one (with some others brand) by myself? (TL-WN722N can use master mode in kernel 3.0 ? already ? some say it should but i've not seen one that stated clearly) Ahh I think the above is totally messed up. I will make long story short.
1. Is AWUS036H or AWUS036NEH support master mode in ubuntu ? (if yes with hostapd or something?)
2. Is TL-WN722N or TL-WN722NC can work in master mode in Ubuntu ? (if yes with hostapd or something?)
3.Can I replace the original antenna with a longer one ?(with other brand or same brand) Will the signal be stronger?
I got two issues with my wifi usb adapter:
1) it cannot see any networks around
2) i cannot setup it in master mode to use my PC as a router
As far as i can see, the device is recognized and the correct driver (rt73usb) is loaded. I was able to connect to a laptop somehow (the laptop could see other networks and the adapter's PC-to-PC network). I'd like to make it work as a router, i.e. share my internet connection (eth0) via wlan0. Here is what i have:
Code:
Ubuntu 10.04
Linux 2.6.32-22-generic #36-Ubuntu SMP Thu Jun 3 19:31:57 UTC 2010 x86_64 GNU/Linux
TP-Link TL-WN321G wifi usb adapter as seen as
Bus 001 Device 006: ID 148f:2573 Ralink Technology, Corp. RT2501USB Wireless Adapter
$ iwconfig wlan0
wlan0 IEEE 802.11bg ESSID:off/any
[Code]....
i try to install my d-link dwl-g520 h/w:A1 in master mode with madwifi drivers but:
$ lshw
*-network:1
description: Wireless interface
product: Atheros AR5001X+ Wireless Network Adapter
vendor: Atheros Communications Inc.
physical id: 5
bus info: pci@0000:00:05.0
[Code]...
after successfully configuring the dwa-552 to work in master mode in ubuntu 10.04 (ath9k driver) I ran some file transfer tests. The download speed is very good (~50mbps) but the upload speed spikes at about 10-20mbps for the first few KB and then it's nonexistent (0-1kbps). This only affects file transfers or otherwise bandwidth consuming processes. Normal web browsing or ssh is not affected. After running a speedtest of my internet connection which is routed through the AP I could upload to the internet with 1mbps which is my inet connection maximum so apparently this is not affected. Tried the same file transfers with netcat to eliminate any other factors and had the same problem. dmesg and hostapd debug did not report anything unusual
View 2 Replies View RelatedI'm looking for a USB wifi which supports master mode, 11n modulation, 5GHz band (with master and ad-hoc support for this band) and has detachable antenna connector.
View 1 Replies View RelatedI am looking for a 802.11n wireless card that Linux supports that can be dropped into AP/master mode.
I would prefer PCI, but USB would be tolerable, just not preferred.
i am wanting to turn my Debian box into a wireless AP, but for some unknown reason the wireless card won't switch into master mode when i run the command #iwconfig wlan1 mode master i get this Error for wireless request "Set Mode" (8B06): SET failed on device wlan1 ; Invalid argument. what does this mean and what do i need to configure/install to get it to work my wirless card is supported i checked it's a zydas chipset using the zd1211rw driver SMC EZ Connect SMCWUSB-G [URL]
View 14 Replies View Relatedafter trying several pci and usb network cards none were able to have their ssid broadcasted. The question that i have is: Can a suse box be converted to act as an acces point without the use of atheros based hardware, without switching over to ubuntu and or debian, without the use of openwrt?
View 4 Replies View RelatedI have Ubuntu 9.10. My USB WG111v3 Wireless Card uses the rtl8187 driver. This driver is buggy. I would like to use Ndiswrapper instead. How to make it so Ubuntu doesn't load the rtl8187 driver but Ndiswrapper instead?
View 2 Replies View RelatedOK, after searching several dozen posts I still have no clear answer to a problem connecting to the internet with my Alfa AWUS036H Wireless USB adaptor. (Computer is an Aspire 5516 w/ AMD Athlon 64 processor)The device shows up in the network manager, (with great signal strength on many local AP's)and works well with Aircrack for security testing, which is why I got it in the 1st place. However my onboard Antheros wifi card just does not receive as well, thus I'd like to be able to use the Alfa for internet. Any thoughts here would be appreciated.
View 9 Replies View RelatedI have a problem with my internet connection this is the picture the device is Realtek RTL8187. i didn't know how can i manage this device to work so could you help me i don't have an internet connection in ubuntu right know and i really wanna move to ubntu my verison is 9.10
View 9 Replies View RelatedMy Realtek RTL8187 Wifi fail to connect using WPA security. The authentication window shows up repeatedly every time I try to connect. Please note the password is correct. I searched and haven't found a conclusive solutions as of yet.
View 1 Replies View RelatedThis is wireless adapter: [URL]... USB/Detail.bok I have 2 AWUS036H Wireless USB adapter that uses the RTL8187 Chipset connected to a USB 2.0 Port. It is very slow when I try to go to websites or download anything using Ubuntu 10.04 Lucid Lynx. The max speed I can get out of it is 135 Kilobytes per second when downloading anything. But when I am on Windows I can max out 2.6 Megabytes per second. I have been trying to find a solution but have found none. When I look at the light on the wireless adapter and compare it to what it looks like on both Ubuntu and Windows. It seems that the wireless adapter light is dimmer on Ubuntu. So I was thinking it was txpower set very low. I changed it but no success on changing speed. I am using WPA2-PSK which obviously uses AES. I have also tested it while it is in WEP and when it is Open with no change in speed. Speed results Ubuntu 10.04: Speed results Windows 7: I changed the settings to Megabytes on those speed results.
[code]...
Ditching Windows for the last time but this seems to be a issue wireless seems fine for a bit but then the connection slows to around 20kbps or worse. Any ideas what it could be? Using 10.04.1 it says it has a 48mb connection and i have 4 bars.
Bus 001 Device 005: ID 0bda:8187 Realtek Semiconductor Corp. RTL8187 Wireless Adapter code...
I just installed Fedora today And man I am impressed, good bye buggy Vista hello Reign. I have the linux driver that came with my adapter software disc. Is that one compatable with core11? If so how do I install it using yum, have been unsucessfull so far. It is for the alfa AWUS036H, RTL8187 chipset.
View 10 Replies View Relatedthis isnt happening on ubuntu but I think this is more or less a kernel problem that could happen with any flavor. After a new install off of a live cd my wireless card is not picking up any signals...i was able to use wireless while using the live cd but now after it has been isntalled to the hard drive it is not working. even tried in terminal to manually look (iwlist wlan0 scan) but it isnt picking up the signal
View 2 Replies View RelatedThe device it's properly recognized and iwlist scan even list the networks, but the "activate wifi network" on the network manager on right-top of the screen it's grey and therefore cannot be activated. This seems to be the problem ( rfkill list ouput ):Quote:
1: phy1: Wireless LAN
Soft blocked: no
Hard blocked: yes
[code]....
I buy a new usb network adapter (Through DX), when I try to use it in ubuntu or BackTrack4 Final it is working, and connecting networks even with WPA encryption. But after few minuts it stops working totally. It is showing that I'm connected to the AP but web sites do not respond.
Notes:
- I have another PCI Wireless adapter which works fine.
- The problematic adapter works great on windows.
- A driver CD came with it, including a linux driver which I wasn't succesfully installed.
- A BackTrack3 Disc came with it, claming by the instructions that the adapter will work with it. I didn't try it because i have backtrack 4 final.
It took me dozens of surfing the web hours, and too many restarts,
I'm managing a residential network. Each flat is its own subnet, and can only communicate with the other flats through a router (i.e. no broadcast). 95% of these 300 subnets only contains windows computers (from lambda users).
My final goal is to be able to browse the entire network from any computer.
I set up a samba server acting as a wins server, and every computer is aware of it because it is registered in the dhcp. So name resolution is working fine for everyone.
The same samba server is set to be the "Domain master browser":
workgroup = WORKGROUP
wins support = yes
prefered master = yes
local master = yes
domain master = yes
os level = 65
When I browse the network (using "net view" or "browstat view"), I can only see the servers which are in the same subnet as the domain master browser.
Now, when in a subnet the computers arrange themselves to find a "local master browser", the only visible computers are the one in that subnet.
What I don't understand is why all the local masters don't synchronize their lists with the domain master.
So, to sum up, every subnet get the following behaviour:
-if a local master is elected, the only visible computers are the one in the same subnet.
-if no local master is elected, the only visible computers are the one in the subnet of the domain master.
-if I add another samba, configured as a local master winning all elections, then the magic is working and the lists are synchronized.
What is expected:
-every computer can see all the computer from all the subnets.
When I first turn it on to the desktop, it automatically connects and disconnects automatically 5 times then sometimes it would disconnect a few times randomly out of the blue.
This ia an external single usb wireless adapter you plug in the usb port on my desktop tower.
I'm looking at buying one of the above cards, and was wondering if anyone knew if they worked in master mode (e.g. as an access point). According to the Aircrack-ng site, they support packet injection and monitor mode. Is master mode support solely up to the driver used with the card, or does the card have to physically support it?
View 2 Replies View Related