Fedora Networking :: Share Between 3 Computers Office Jet 5610 All In One
Jan 29, 2010
As the Subject mentions I have an Office Jet 5610 All in One Printer that I am trying to share between 3 Computers.
Computer Number 1: Laptop running Fedora 12 with the Gnome desktop. This is the computer to which the printer is physically connected to. I have no issues printing from this printer at the laptop. I have installed both samba and cups. I can access cups online and manage the printer from the Laptop with no issues I have checked to make sure sharing was turned on and in the laptop i have made sure that internet sharing with the printer is turned on.
Computer Number 2: Desktop running Sabayon 5.1 with the Gnome desktop. I can see the printer and it tells me that its ready. I try to print a simple test page and i get error: Destination Printer not accepting Jobs. I'm not sure if this is a Sabayon issue a Cups issue or a Fedora Issue.
Computer Number 3 Desktop running that Redmond Crap (Wifes Computer) Yeah Redmond wont even find the network printer much less print to it.
I forgot to mention that i have checked my firewall to make sure IPP was allowed and Samba was allowed so i do know that these are not the issues. I do have SELInux installed and running though don't know if this could be the culprit or not.
View 2 Replies
ADVERTISEMENT
Jun 8, 2010
if i have Fedora 13 installed on a desktop and on a laptop, can i organize so that both machines use the same dsl connection? I have an external DSL modem that is currently connected to my PC via an ethernet cable. When I want to use my my laptop I usually unplug the dsl connection from my computer and plug it into my lap top. is there some way i can have it connected to both?
View 9 Replies
View Related
May 28, 2010
Trying to share my internet connection with other computers on my LAN. I've tried doing this with Debian, Ubuntu & Fedora so far...
My Intended Setup is as follows;
The Problem: So far I've not been able to get an internet connection from any computer connected to the HUB. I currenty have Fedora 13 on PC1 but have also tried with both Ubuntu 10.04 & Debian Lenny. I am open to using any Linux based distro on PC1 as long it has a Gnome Desktop. eth0 on PC1 can be Static or Dhcp, but I would prefer to set Static IPs on eth1 & all of the Client PCs
To the best of my knowledge I have enabled ipv4 forwarding in sysctl.conf (& some other changes);
Code:
All changes I made to the Firewall (all other Firewall settings are still at default, no custom rules added yet);
Router is set up to assign dhcp from 192.168.xxx.100 & 192.168.xxx.200
At the moment I have only 1 PC attached to the HUB. It's Ubuntu 10.04 (PC2)
It's details are;
ip 192.168.xxx.103
netmask255.255.255.0
gateway 192.168.xxx.101
Thus Far I can't ping 192.168.XXX.103 from PC1 & I can't ping 192.168.XXX.101 from PC2. (unreachable) I have an internet connection on PC1 (of course)
View 1 Replies
View Related
May 8, 2011
I have two Ubuntu 10.10 computers and two Windows XP computers connected to my network. I cannot share files between the Ubuntu computers using samba. I keep getting the "Unable to Mount Location Failed to mount Windows share" error. I've tried the solutions posted by dmizer here and nothing works.Random true facts:I can successfully connect to folders shared on my Windows XP computers from either windows computer.I can successfully connect to folders shared on my Windows XP computers from either ubuntu computers.Neither of my windows computers cannot connect to folders shared on either ubuntu computer.Neither ubuntu computer can connect to folders shared by the other ubuntu computer.I REALLY need to get samba to work since I have other Windows computers on my network.
View 8 Replies
View Related
Nov 20, 2010
I am having a heck of a time trying to find directions on networking my two computers together in order to share files. I have two machines running Ubuntu 10.10 Desktop & Netbook remix.
They are both connected to my wireless router to connect to the internet.
View 9 Replies
View Related
May 30, 2010
i have two machines both on ubuntu 10.4 connected to a network via port switcher, 2 rj45 network cables auto eth0 is setup to share with other computers, i can ssh in and out of both, so the network is all running but i want to know how to share my single dongle internet connection between the 2 computers
View 4 Replies
View Related
Jul 14, 2010
I have a usb 1tb drive that I want to share over my netowork, but when i share it through nautilus, it doesn't mount right on other computers, ect. Is there a way to mount it. The location of the drive is /media/FreeAgent Drive___
View 3 Replies
View Related
Oct 24, 2010
I now have 3 desktop computers hard wired into my wireless router and another desktop plus 2 laptops connecting wireless. All are running Ubuntu 10.4 or 10.10. I have not had the chance to get them all upgraded yet. What is the easiest way to get these computers connected so that they can share files? Do I have to set up a server or is there a simpler way? I just want to be able to copy a file from one computer to another.
View 9 Replies
View Related
Jul 22, 2010
I would like to share gnote notes between two computers. The documentation talks about synchronizing with a server, but there are no synchronization menu options as the manual suggests. Is is possible to either synchronize notes between two computers or at least export notes from one computer and copy to another? This seems incredibly simple and basic but surprisingly I can't find a way to do it.
View 2 Replies
View Related
May 8, 2011
Networking Problem Fedora 14 2.6.35.12-90.fc14.i686. I am trying to share files between 2 Fedora 14 computers , a desktop and a laptop, both located on my local DSL server. The laptop sees its public files and the public files folder on the desktop computer - looks fine. The desktop computer acts differently. Both systems show an entry of "unknown type" in the directory listing, for the public files directory. But whereas a right click on the directory entry on the laptop offers "open" the same operation on the desktop computer offers "open gedit". When I double click the entries on the laptop, entries appear on the main screen. If I double click the entries on the main screen, the directory contents are displayed. But, if I doubleclick the directory entries on the desktop computer 1- I get a black box that says there has been a crash in gvfs-1.6.6-1.fc14 and an error message box tells me Dbus error org.freedesktop.DBus.ERROR.NoReply: Message did not received a reply.
View 1 Replies
View Related
May 17, 2011
I can not edit my own .ppt file from samba share. Current desktop OS is windows 7. Samba server having RHEL 5 with following samba packages installed.
Code:
libsmbclient0-3.5.6-43.el5
pam_smb-1.1.7-7.2.1
pam_smb-1.1.7-7.2.1
I can able to edit and save the file if I copy this file from samba to local system. But from Samba share it open in read only mode.
View 7 Replies
View Related
Jan 3, 2010
I just recently constructed a computer to create a nice Fedora Linux server to replace a Mac Mini server that I have been using for a few years. I'm attempting to create a Samba share for my machines, a Windoze 7 machine as well as a couple MacOS 10.6 machines. I've set up Samba, started the service, allowed Samba in the firewall, and used system-config-samba to set up a share with a user. I created a User called "space", and a share /media/peliculas/Movies (a mounted hard drive). When I type in \IP_ADDRESS in the address bar in windows 7, I get the option to log in. I log in correctly and I see two directories "space" and "Movies." Unfortunately when I click on one of them I get the following error message:
Windows cannot access \IP_ADDRESSMovies Check the spelling of the name. Otherwize, there might be a problem with your network. To try and identify and resolve network problems, click Diagnose. I also get something similar when I attempt to connect with my mac machine. Using "Connect to Server" I type in: smb:\IP_ADDRESS, and login, I have the option to mount "Movies" or "space." If I select any of these, I get the following error message: There was an error connecting to the server "IP_ADDRESS." Check the server name or IP addres, and then try again. If you are unable to resolve the problem contact your system administrator.
Also, if I type 'smbclient -U space -L IP_ADDRESS' I can see the "Movies" in the "Sharename." At this point I'm not sure what else to do, and have been trying to figure this out for the last few days (losing sleep due to being baffled). The only thing that I can think of is that I have something wrong with the smb.conf file. Here is what it currently displays:
Global Settings
workgroup = WORKGROUP
server string = Samba Server Version %v
log file = /var/log/samba/log.%m
max log size = 50
[code].....
One last thing, when I check the log files, there are error messages that state: smbd/service.c:1009(make_connection_snum) '/home/space' does not exist or permission denied when connecting to [peliculas] Error was Permission denied --Windoze 7 and MacOS 10.6 log files
View 5 Replies
View Related
Sep 16, 2010
I am wanting to setup an office network consisting of three computers and one server. We already have the equipment ready with Vista Business pre-installed on the computers. I want to be able to create a network which allows users to use any machine as this will reduce downtime should a machine break. Also I would like user's files to be held centrally on the server which makes backups easier.
The most important element here is data backup. As like most businesses we are moving away from paper and using the computers to store important records such as customer information. If this data were to be lost, the business would come to a complete halt.
I have been looking at the idea of installing a Microsoft Small Business Server as it would be nice to have centralised control of the machines. However the cost would be over 800 which can not be justified for three machines and five users. Therefore I am turning to Linux for a alternative solution. I have previously used CentOS and Ubuntu for home use but never really gained much knowledge or experience of either.
It is my understanding that Samba can act as a Primary Domain Controller, which if I'm not mistaken is where it handles the network logins and profiles. Is this correct? I have come across many samba tutorials online but whats confusing is they are all different. Some of the tutorials involve using Kerberos and OpenLDAP. Do I need to learn about either of these? What do they do and what benefit will they bring?
Finally, I see Samba 4 is in development and is likely to bring a lot of new features which aren't available in Samba 3. Is this worth waiting for because I don't want to be upgrading everything again 6 months down the road?
View 9 Replies
View Related
Jan 8, 2011
I am at a university where my bandwidth is severely capped. I can start several other computers near me and download at the limited speed simultaneously. Is there any way for me to share the download between the computers to get the cumulative speed?
View 1 Replies
View Related
May 5, 2010
I am used to Ubuntus simple sharing with samba. Just install it, reboot and then share the files.Then do I klick on network folder and see all the shared files on the computers in the network.
How do I install it so I only need to go into network folder and see the other computers shared files.Then, how do I share files?
I hope it's not so difficult and that I have to change i config-files.
I am new to Fedora.
View 4 Replies
View Related
Feb 14, 2010
Im trying to set up a share between my 2 ubuntu computers. I set one computer to share a folder in the properties tab, and installed the corresponding software. now, how do I search my local network for shares?hat type of share is it? NFS? Is there a tutorial out there some place?
View 1 Replies
View Related
Feb 19, 2010
I can't seem to figure out how to even share files between my laptop and desktop. They are both Ubuntu 9.10. I thought maybe samba was the way but couldn't figure it out. I was looking at the ssh that comes with Ubuntu and been trying to get it to work but don't know what I'm doing wrong. I type: ssh username@computername and it give me a little info. Don't know what I'm suppose to do then. I looked at the network folder on my laptop and it seem to see it but everytime I click on it ask for a password and I can't get in since I don't know the right password. I'm not sure if this is the best software to use or not. Just wanted something to look at and transfer from my desktop to my laptop and vice versa.
View 7 Replies
View Related
Mar 11, 2010
I would like 2 computers (same network) to use the same SQL database. How should I start?
View 2 Replies
View Related
Jul 2, 2010
I have Ubuntu on one machine and open SUSE on the other. Both connected with an ethernet cable to the same router. Both connect to the internet ok. I did manage to set up 2 machines both running Ubuntu with file sharing but now I have switched one to SUSE I seem to be getting into a mess. Ubuntu sees the SUSE machine but does not open any folders. SUS does NOT see the Ubutu machine. I have looked for a beginners guide to setting up file shaing with SUSE without success. (I like SUSE better because I can use my Audiophile sound card "out of the box")
View 9 Replies
View Related
Aug 26, 2010
I have 2 Ubuntu Computers on my home network. I haven't figured out the ways that I can connect these 2 computers to share files, remote desktop, etc. What are all my options?
View 5 Replies
View Related
Jun 6, 2011
2.0.0 Banshee
2.6.38-8-generic
Mint 11
I have a large (114GB) music collection, collected over the years and stored on NAS. Various sources and formats from my MS days and .ogg and .flac recently. Having just upgraded from Ubuntu 10.10 using Rythmbox and having some spare time on my hands I thought I'd get some of my collection in order. The music is organised into various categories in a directory on the NAS: /music/category/artist/album_name/ where category divides things up into styles like Classical, Reggae, Soundtracks, French, and a ubiquitous "General" category
There are 5 or 6 computers attached to the network, all running linux/banshee and reasonably in step with each other. 2 of them have the full set of categories on, one is my main PC, the other is connected to the Hi Fi, the others have various usages and a subset of categories on. There could be an update to the metadata (scoring and/or track and artist info) from any one of the PCs, but probably only from 3 of the machines. I have seen some options in edit>preferences which seem to write metadata and scores to files but cannot find anything in the user guide on how to exploit these. Is there a way to sync (and merge) the metadata from each of the machines so I'm not rewriting it on every machine, depending on the size of the files can this be done using the preferences by writing back to the NAS or using something such as dropbox to keep them synced.
View 6 Replies
View Related
Oct 2, 2010
Trying to find out how to share files between two computers on my Home Network.Tried VPN but not sure how to configure. I am using Linux Mint 9.
View 3 Replies
View Related
Nov 3, 2010
i'm trying to automount a samba share on computers startup, everything works just fine when the network adapter is controled by traditional way ifup but when i'm switching to NetworkManager doesn't work anyway. i'm hiding the share information from the common user by using the /etc/samba/cifstab as i read on intrernet, in the cifstab i put //server/share /home/user/share cifs sername=user,password=pass,uid=1000,_netdev .could anybody give me a hint or tell me where to look?
View 3 Replies
View Related
Feb 26, 2010
I have a samba share setup as the following. When I browse to it from PC's added to my AD domain, they connect instantly. When i browse to it from a laptop that's not part of the domain, i get prompted for login credentials. what credentials should I be putting in? I can't seem to figure it out. or is it because i have the workgroup set to what my AD domain name is, and the laptops aren't part of that domain.
path = /data/photos
browseable = yes
force user = pictures
force group = picturesgroup
[code]....
View 12 Replies
View Related
Oct 2, 2010
After upgrading my ubuntu server from 9.04 to 10.04, the window computers couldn't resolve samba shared names anymore, the error code displayed by Windows was 0x80070035.
I was using the ubuntu server as a samba server, using 'share' as the security authentication method, it has been working very well under previous ubuntu versions but, after upgrading to 10.04, the windows computers can't access the server shares anymore; the linux computers don't have any problems (I can access the shares from linux).
As a workaround, I've added the name of the server in c:windowssystem32driversetchosts; but I'd like to know how to fix the problem without modifying every windows computer.
View 1 Replies
View Related
Apr 21, 2009
I have 5 or 6 computers on my home network. Most of them are wired connections, a few wireless. All the Linux machines run Samba and they are all configured identically. Workgroup name is the same on all, user=share on all and they all have a share or 2. I can ping any one from any other but they don't all show up when I run smbtree, usually from my wireless laptop. Maybe I should run it on all the Linux boxes and see what the result is, but I've never done that. My question is, why do they not all show up? One of them never shows in the list. The Windows boxes always do.
View 10 Replies
View Related
May 23, 2009
I have a laptop (running Fedora 10 KDE version) and a desktop (running Ubuntu 7.10) on my home network. Is there any way to send messages from one computer to another through LAN ?
View 5 Replies
View Related
Oct 20, 2009
I downloaded and installed a new copy of Fedora 11 last week onto a new computer (hereafter "proximate"). I also have a remote computer without a monitor running an outdated version of Red Hat Linux (hereafter "remote"). To manage the processes on remote graphically, I ssh from proximate into remote; this connection succeeds without incident in transmitting text (including commands) between the two computers; however, the command "gnome-session" returns: (gnome-session:15789): Gtk-WARNING **: cannot open display:
(The numbers apparently represent the process identifier and vary from instance to instance.) A similar warning (and no accompanying graphics) occurs whenever I attempt to start any graphical user interface from remote via ssh from proximate. The issue almost certainly lies with proximate; remote successfully communicated graphics to the ancient box that proximate replaces.
Interestingly, I cannot communicate via ssh from remote to proximate (within a secure shell from proximate to remote). If I execute /usr/sbin/sshd on proximate as root, then I can login, but even then I cannot execute any commands.
Consider the following output:
If I execute ssh -vvv proximate from remote to proximate, then I get a lengthy output that ultimately ends with "debug1: Exit status 254."
What must I do to communicate both text and graphics among my computers?
View 3 Replies
View Related
Sep 28, 2009
I am using Fedora 11 all upgrades, wireless network WUSB54G network adapter. I can get to the internet but cannot get to any Windows (192.168.1.100) or Fedora 11 (...104) computers, printer (....101, 105). Here are the tests I have run.
[root@Fedora2 sbin]# ping 192.168.1.1
PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=1.76 ms
64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=268 ms
64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=1.63 ms
^C
--- 192.168.1.1 ping statistics ---
View 1 Replies
View Related
Oct 18, 2009
I'm pulling my hair out to figure out what's gone wrong. I have a small home network with a router and 4 computers, 3 linux boxes and 1 windoze machine.The windoze machine and 2 of the linux boxes (newer ones, one with FC11 and the other with Ubuntu Hardy) are using the router's "Set Static IP" option just fine. However an older FC5 machine I have always gets its IP assigned randomly. As this is the machine I ssh into from overseas via a Dynamic DNS, this is a huge frustration when the power goes off or I need to restart the machine. It's usually 192.168.0.2 but sometimes 192.168.0.3 and occasionally other numbers as well. It _should_ be 192.168.0.130. As near as I can tell, I'm doing everything the same between the machines. The router config is very simple and works for the other systems so I suspect I may have a legacy tweak that I did years ago that's causing the problem.
Anyone know what I can try? I'm afraid I'm not a networking guru (ahem, wouldn't be posting if I were!) so things like "check the this" will be more helpful if there's a clear example. "Check the this...emacs /etc/thisfile/config" and see if XYZ option is TRUE" is far more useful. Again, many thanks. If none of the systems were working right then it would be totally different...but 3 seem to work just fine and happily get their assigned static IPs. It's the one non-conformist that's the trouble...
View 1 Replies
View Related
