On one of my F10 boxes yesterday, I installed several NM packages with yum update after being advised of their availability. Today, (the first reboot since installation) I no longer have network access on that box.
View 2 Replies
I was having trouble with some software detecting ports so i removed ufw and now have no internet
Ive tried and none of these work:
The internet has been working happily on my Mythbuntu machine for many months but stopped working overnight.If I try to do "sudo start networking" I get a "Job failed to start" message.There's also a solid orange light on the ethernet socket.As it's been working for months, I don't think my interfaces config needs updating.Looking at what's been updated recently on the system:
1) I've configured the machine to wake from USB. It was working for a couple of days so I don't believe this is the issue.
2) I set up wake-on-lan with ethtool. Again, this was working (although it did seem to disable wake-on-usb and required a reboot to fix)
3) Update to 11.04 - I said no to this, as 10.10 was working very nicely indeed.
I've disabled wake on lan and rebooted. No joy.
ethtool detects the ethernet controller ok and it's listed in lshw.
Just installed Ubuntu 10.10 on dual boot computer. Each OS is on separate hard drive with GNOME selection between Ubuntu and Windows 7 Ultimate. Firefox was working fine yesterday when I went to use today, nothing. Email through Thunderbird is down as well.
View 3 Replies View RelatedI've just installed Fedora 10 to basically work as a NAS for another machine - but also serve a couple of web pages. After having alot of issues with network manager (with it changing the subnet so nothing would work), I'm now almost there:
I have two network cards connected in the server:
1) eth0 connects to a switch that ultimately connects it to the net (on a 10.0.0.* network)
2) eth1 connects directly into another server for backups (192.168.0.* network).
Now when I setup eth0, I get network access can ping/ update/ surf the net - absolutely no problems, but when I connect eth1 in - the net dies and nothing works, I can ping devices on both the 10.0.* and 192.168.* networks, just nothing past the gateway. I presume this is either a route or DNS issue, but am unsure about where its falling foul - both the resolv.conf file looks fine as do the ifcfg-ethx scripts.
I'm new to Fedora 10 and still a newbie with Linux in general. I installed F10 on an old PC I had....and the install went well..however, I'm having Internet Connectivity issues.
Here is what I did so far:
Did an ifconfig command and I have the following:
pan0 Link encap: Ethernet HWaddr D2:30:36:AF:61:95
inet6 addr: fe80::d030:36ff:feaf:6195/64 Scope: Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:30 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes: 0 (0.0 b) Tx bytes: 8676 (8.4 KiB)
When I go to the Network Configuration Panel I see the following:
Status: Device: Nickname: Type:
Inactive pan0 pan0 Ethernet
Tried to activate and it states Activating network device pan0, please wait... determining IP information for pan0.... A few minutes pass by then. It indicates it failed. Cannot activate network device pan0! I have disabled the Controlled by NetworkManger and enabled the Activate device when computer starts.
I just installed F15 on a laptop that previous had F12 working well. During install, it finds my wireless card and seems to set it up fine. The full install ran with the wireless active without any problem that I could see. Now, when I start up, I see Network Manager tells me that the wlan is active, but it doesn't show my specific network. If I click on the NM tray icon and open up the panel, my network is shown but it is not "active".
I can double click on it and it will become active - shows the little globe next to the antenna. This works fine for about 2 web pages worth and then FireFox 4 stops being able to find web pages. If I go back to the panel, double click on my wireless network (which looks like it is active already), and reactivate it, I can get the page I was looking for in FireFox, but within a couple of minutes it will stop.
Likewise with yum, while I'm installing software, I'll occasionally get errors like this:
[URL]: [Errno 14] curl#6 - "Couldn't resolve host"
If I reactivate my wireless network in the NM panel, it continues fine. Other computers/phones connected to this network seem to work fine. Is NM known to be problematic in F15?
how to install firmware-b43-installer without internet connectivity. I downloaded firmware-b43-installer from another computer with internet. Then I found out from the error messages I also needed b43-fwcutter. So I also downloaded then installed b43-fwcutter. b43-fwcutter installed with no problems. Then I tried to install firmware-b43-installer again with no luck. I saw in the error messages it said something about broadcom-wl-4.150.10.5.tar.bz2. I have no idea how to install a tar.bz2 file.
Here is where I downloaded the files I needed.
http://archive.ubuntu.com/ubuntu/poo...10.5-4_all.deb
http://archive.ubuntu.com/ubuntu/poo...013-2_i386.deb
http://mirror2.openwrt.org/sources/b...0.10.5.tar.bz2
I have all the files now so what do I need to do to install firmware-b43-installer?
I have a dial-up connection through PeoplePC and I'm running FC11. In order to get my modem working, I'm told I need to install the wvdial package. To get wvdial, I need wvstreams. I downloaded the source for both on my Windows machine, and transferred the .gz files over to my FC partition.
When I try to ./configure wvstreams, I receive an error about not having a C compiler at $PATH. I'm pretty lost about what I need to do to correct this.
Basically I just want my dial-up to work with FC11
Here's a link to exactly what it says: [url]
I am using Suse 10 sp2. By running ifconfig I am changing the mac address. Everything is happening successfully, but this is adapter losing the network connection. Even when I give a static IP. I am not able to ping any other IP.
View 1 Replies View RelatedI thought to uninstall Gnome Network manager since it was always asking for to connect with wireless internet but it was working fine with wired internet.I uninstalled it and installed wicd. and then for some unknown reasons the internet disappeared.Kindly let me know How can i get back network manager without having internet and make internet work on my computer.I did searched a lot on Ubuntu forums using somone's else computer but no success.So if you let me know how to approach the problem in right manner it shal be great .
View 6 Replies View RelatedI had my desktop running ubuntu 10.10 at my sisters house hooked up to a router sharing internet with her boyfriend never had a problem with it there. I moved into my own apartment this week plugged the cable modem directly into the broadcom ethernet card and couldn't get an ip or anything it wouldn't connect period so I ended up hooking it up usb which works but only at speeds of 5-7mbit when I have 15mbit connection. So I put another ethernet card in hoping it was just problem with the card and tried it that worked.
I got a connection but it was incredibly slow like getting maybe 5k a second so I open network tools in administration menu and start pinging google. While I'm waiting on a bandwidth test to complete and it takes off getting like 20mbit keeps that connection for a while then out of nowhere just drops to almost nothing. Again for a few minutes then falls off completely so I restart and it does the exact same thing starts off slow then something clicks and it works great for 5 min then nothing?
I have a server with two ethernet ports. I configured eth0 to be static, set at 10.1.10.148. I plugged in another router into the other ethernet port in order to configure that router. I configured eth1 to use dhcp. Using /etc/network/interfaces rather than gnome network manager. When I did this, I lost internet connectivity (internet routes through eth0 of course)
- Why did I lose internet connectivity?
In order to recover internet activity, I had to disconnect the new router on eth1 of course, and do sudo ifdown eth1. That wasn't enough however. After rebooting numerous times and pulling out my hair, I finally tried configuring eth0 as dhcp, rather than static, and this fixed the problem.
- Why didn't sudo ifdown eth1 solve the problem? What information was saved between reboots that somehow remembered that I plugged in the new router? Because my thinking was if /etc/network/interfaces was identical, and the network topology was identical, after a reboot everything should be restored, but it wasn't.
I installed Fedora today, and I automatically had internet connection, I never had do configure anything myself. Then, I was playing around with VPN for a good while (trying to set up the VPN connection to my University), and now, I suddenly lost my connection to the internet!
But only Fedora can't connect anymore, the Windows PC has connection as well as my Mac OS X (I dualboot Linux on my MacBook). The Ethernet connection works as well, when I unplug the cable, Fedora gives me a message, but I just don't get into the internet!
Does anyone have an ides what I have to do? I don't know anything about network connections and I'm new to Linux...
I already restarted the Computer, but that didn't work, and Google didn't really held either.
Wife's laptop has AR5001 Wireless Adapter laptop model is Toshiba Satellite A215
Problem : Wireless networking randomly loses connectivity and can not regain connectivity, the only apparent solution is a full power down , this is not even certain to work. The card works under Windows, she hates Windows. (I love her for this) I know it's not faulty hardware , because it will work for days on end under Windows without problems.
Things I've tried : madwifi drivers (any and all versions available) : These increase stability of the signal and seem to delay the inevitable however it still happens. When using these drivers the only option is to unload them modprobe -r then reboot then remove them again and re add them. It makes no sense why this works, and if I don't remove them prior to rebooting it will not work.
ATH5K drivers : These are pretty much junk, results are unpredictable at best, sometimes it will work perfectly for a few hours, sometimes it will not work at all. Nothing is repeatable, I can't seem to force whatever condition is causing this. rfkill does not show the wifi being blocked (hard or soft), unblocking it anyway does nothing, only way to make this work and it's iffy is to fully power down wait 5-10 minutes turn it back on and it MAY decide to work.
Firmware update : Updated the Toshiba BIOS to the latest version of the firmware 2.0 no joy here either. Same issue both sets of drivers.
Tried different distros and kernels : I've tried Mint 9, 10 ,11 ; Ubuntu 10.10, 10.04 , 9.10 and 11.04 (which is currently installed) , Fedora and OpenSUSE. All are giving the same problems. I have also tried a slew of different kernels no joy from any of them (I'm not at the computer with the issue now I will post exactly what kernel versions I've used when I have access to the machine).
Another useful bit of information, the hard switch to disable/enable wifi WILL disable it but turning it back on does absolutely nothing. The hotkey does nothing at all. The bios does not have an option to disable or enable the wireless card.
I will also post the typical lsmod , lspci , iwconfig all that good stuff when I get back to the computer in question. I'm probably just going to buy a PC card for it and give up on that one, but this is driving me insane and I would really like to see it resolved even if I do replace the hardware.
I have an iphone, I am trying to get internet connectivity to that phone through wifi. I dont have a wifi router. But i do have a laptop with wifi card. I am connecting to internet via cable modem. In win7 I used to create an accesspoint and do the ics from ethernet card to share via wifi card. It used to work perfectly.
Now as I am sing ubuntu, i want to do the same. I have intalled firestarter, and shared the internet connection through wifi card(wlan0).After this I created an accesspoint using the gnome network applet. Now i can connect my ifone to ths accesspoint. But there is no internet connectivity in my fone.
I can connect to anything locally, I can SSH in locally but nothing works from outside my network (can't access pages in apache, can SSH, etc.) I've checked the logs I can think of, but what should I be looking for? The last thing I did today was add a FW rule to log and drop from an IP, saved my iptables to a file in /etc. (this was at 10:45am). The last time I successfully logged in remotely 1:03pm. I connected multiple times in between. I've rebooted remotely once or twice. That's it. I've already flushed iptables.
View 1 Replies View RelatedI am using fedora 8. I want to upgrade my system but I don't have internet connectivity I cannot use yum can any body tell me from which site I can get all the rpm packages specially gcc, glibc so that I can take them in my pen drive and install in my f8.
View 3 Replies View RelatedI am new to linux. Whenever I boot my system. I always have to click on system eth0 to enable internet connection in network settings. How can I make it permanent so that as system boots up, network connectivity is itself enabled.
View 1 Replies View RelatedI am new to UBUNTU. I installed the latest one alongside windows 7. I am having problem with the internet connectivity. I configured the static ip settings right I guess. Edited the Auto eth1 and assigned ipv4 settings manually and entered everything correctly.
Address 192.168.xx.xx
Netmask 255.255.255.0
Gateway 192.168.xx.xxx
DNS Server xxx.xxx.xx.x, xxx.xxx.xx.x
Do I have to put MAC Address as well? Which is addressed as 'Network address' in Windows where I put this MAC. I have on board Realtek RTL8101E Family PCI-E Fast Ethernet NIC (NDIS 6.20) Network adapter. Do I have to install the driver?
I am a new user to linux. I downloaded and installed ubuntu 9.10 on my old desktop to try it out because i have always liked the idea of linux but have never really found the time to use or learn to use it. having had an old dos computer i can vaguely remember the idea of using a command line to change directories etc. so i just decided to wipe out xp on the desktop and install ubuntu lol. Installation went smooth but then i ran into some problems.
Unfortunately i use iphone tethering for access to the internet but ubuntu will only recognize my iphone as a picture storage device. so i did some research and found that i had to download and install some packages to set up tethering on ubuntu. so on my laptop running vista i downloaded libusb-1.0.6, cmake-2.8.0, libiphone-0.9.5, usbmuxd-1.0.0, and some other packages such as ifuse and libgpod. they were all .tar.bz2 files or .tar.gz files. I put these on a jump drive and took the jumpdrive and put it into my desktop. what i was wondering is if there is a way to install these packages from a usb jumpdrive? or is there a simpler way that i may have overlooked to establish an internet connection.
im using fedora 14 and i have a slow internet connection. i want 2 install some packages from the fedora 14 dvd instead of downloading from internet using add/remove packages. i tried to edit /etc/yum.repos.d/fedora.repo and /etc/yum.repos.d/fedora-updates.repo but it dint work.
View 2 Replies View RelatedI have a laptop with internet and ubuntu, and a desktop without internet, and I need to install some pakages on it. I did my research and generated a script to download them from synaptic, but when I double click it, it opens it gedit, when it is supposed to download the packages. What am I doing wrong? I was using this article [URL]
View 3 Replies View RelatedI am using Suse 10 sp2. By running ifconfig I am changing the mac address. Everything is happening successfully, but this is adapter losing the network connection. Even when I give a static IP. I am not able to ping any other IP.
View 9 Replies View RelatedI had Fedora 7 which works fine with my PCI card Linksys WMP54G-EU (00:0b.0 Network controller: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller (rev 03)).
It ran with ndiswrapper.1.51.
Yesterday I installed the live-CD Fedora 10 on a new partition in another hard drive and so I have Fedora 10 but WITHOUT Internet connection.
I tried to install Ndiswrapper but the 'make' command doesn't exist in my Fedora 10 !
What are all the things I need to download from Internet to ensure the several commands like 'make uninstall', 'make', 'make install'... and to ensure installing Ndiswrapper ?
I am using the VirtualBox PUEL version, and I used to run Windows + the driver program of my Lexmark USB scanner - successfully. Now I have upgraded to Karmic, and when I try to attach the virtual machine to the USB scanner I see its line (and all other lines) greyed out, see the screenshot below:
Thus I have lost USB connectivity after upgrade to Karmic. Also in the yellow status box "Unavailable" appears. how to use my scanner and other USB devices again?
I wanted to try to install one of those public VPN services in order to try a software program. I setup a VPN for a service that is located in the UK. I successfully installed the VPN that just required me to use their gateway address and they also supplied the username/password. All I did was edit the connections from the Ubuntu Network Manager to add the VPN. After rebooting I no longer have my wired "eth0" connection listed and the Network Manager shows a red X.
I use a DSL service and my computer is directly connected to the router. I am using Ubuntu Natty 11.04. I read where you may have to edit the /etc/udev/rules.d/70-persistent-net.rules because it may cause an entry of eth1 instead of eth0. My file still shows eth0. I have also deleted the contents of that file and rebooted, as suggested in other posts, and eth0 is in the file, but still does not show in my Network Manager.
If I type in terminal: sudo ifconfig | grep eth, I get an output of:
eth0 Link encap:Ethernet HWaddr [my mac address]
Going to Whois shows my IP address as that from my local ISP. Clicking on Network Manager > Connection Information, I receive a window that states : "No valid active connections found". Obviously, I am connected to the Internet. Is there a way to restore my eth0 connection?
I am running ubuntu 9.1 on a Dell Dimension 2400. After installing ubuntu on the pc, it was automatically recognizing my router and connecting to the internet fine via ethernet. Then, my roommate unplugged the router and it won't recognize it. I can't access my router settings, and ubuntu is recognizing it as "inactive" but every other computer in the apartment runs fine. My PC uses a broadcom ethernet controller, and my router is a Linksys wireless N.
View 1 Replies View RelatedI added RAM to my Acer (dual boot Windows XP / Ubuntu 9.1). Windows continues to work. Ubunty will no longer recognize the internet connection. I don't know if adding the memory is what did it, but I am puzzled why I can use the ethernet card from Windows but no longer from Ubuntu.
View 7 Replies View RelatedI was downloading the Android SDK when, mid download, I lost my internet connection. Now I cannot connect to the internet via hardwire connection. I can still connect on Vista, and I can connect via wireless, but I cannot have a hardwired connection.
I was following these instructions [URL]
