Fedora Networking :: FC10 - Int-bond0 Doesn't Comes Up During Boot?
Mar 4, 2009
I'm bonding the two NICs on my FC10 server to create a bonded LAG between it and my Cisco Catalyst switch, but during kernel init, the system always give me a notice that "bond0 doesn't appear to exist" so it skips it.Once I log in, I can always open Network Manager and the bond0 interface goes from "Inactive" to "Active" and bond0 immediately works, and I can restart the appropriate network services and everything is fine. But any idea why this bonding wouldn't be initializing during boot up? The ports on the Cisco are configured for hard set speed and duplex and portfast is turned off on them.Is there a guide for best practices for creating LAGs (bonded interfaces) between FC10 and Cisco switches?
View 4 Replies
ADVERTISEMENT
Jan 20, 2009
I am trying to boot kubutu from FC10's grub. FC10 is in MBR, installed kubuntu without grub. Is that a problem for me now? I mean, should I need to install kubutu grub in order to boot from FC10 grub? I tried with these methods but nothing works:
title Kubuntu 8.10 Linux
chainloader +1
title Kubuntu 8.10 Linux
[code]....
View 4 Replies
View Related
Sep 2, 2009
I have just updated KDENetwork to this level and now my F10 doesn't find any wifi connection. By the way, I have been working with F10 for some months without any problem on wlan.
iwconfig now says:
wlan0 IEEE 802.11bg ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=0 dBm
Retry min limit:7 RTS thr:off Fragment thr=2352 B
[code]...
View 1 Replies
View Related
Oct 17, 2009
Sometimes (but not every time), when booting my Dell Inspiron 530, eth0 will not come up right away. I can boot and log in to Gnome, and the NetworkManager applet shows that the ethernet cable is unplugged. After sitting for 5-10 minutes, it will link up and everything works. If I unplug the network cable and plug it back in, it comes right up. But once it's linked, it works fine and never disconnects after that. I've tried switching to a different port on my switch and a new ethernet cable. So I suspect it's some sort of weird kernel problem. I checked /var/log/messages and the only thing that looks weird is:
Oct 17 07:51:49 obi-wan kernel: e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k6
Oct 17 07:51:49 obi-wan kernel: e1000e: Copyright (c) 1999-2008 Intel Corporation.
Oct 17 07:51:49 obi-wan kernel: e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level,
[Code].....
But I have a second Inspiron 530 that has the same entry and it works fine. Has anybody seen a problem like this? I've looked around and so far can't find out the exact issue. I've upgraded NetworkManager to the latest version for FC10
View 3 Replies
View Related
Mar 3, 2009
We (2 persons) are experiencing a total freeze on first boot after installing fc10 from the 6 CD distro set, and yes, we used the same discs but ran the validate check on each. One machine is a rather ancient Acer G7500G which had previously been running FC3 happily; the other is a very new Dell Notebook (now running FC9 happily). The freeze occurs after the progress bar turns all white. Pressing escape shows that the volume group(s) have been found and are now "active", but that's all she wrote.
The systems can be mounted in repair mode and I notice that there is no "functions" file in /etc/rc.d/init.d but this may be normal for FC10.
The Del owner have officially given up, but before I throw FC10 out and go to 9 also, I though the question was worth asking: has anyone installed FC10 from the CD distro as opposed to the DVD distro successfully?
View 9 Replies
View Related
Mar 30, 2010
How to tell dhcpd to listen to ifcfg-bond0 ?
View 1 Replies
View Related
Mar 3, 2009
I installed fedora on my second hdd, the other one had xp before fedora, now in grub it shows xp as other and wont boot into it, just hangs there. SDC is an external drive and sdb is the xp drive as you can tell by the filesystem.
Disk /dev/sda: 320.0 GB, 320072933376 bytes
255 heads, 63 sectors/track, 38913 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x836db2c4 .....
View 1 Replies
View Related
Jul 26, 2009
I've been upgrading all our servers from FC8 to FC10. One thing that is no longer there are the start up script messages, being replaced by the white and blue line at the bottom.
I like seeing the bootup messages when I reboot (rarely) to make sure nothing went wrong and not having to go into boot.log to check it.
Code:
Reading all physical volumes. This may take a while...
Found volume group "VolGroup00" using metadata type lvm2
2 logical volume(s) in volume group "VolGroup00" now active
Welcome to Fedora
[Code]....
View 2 Replies
View Related
Dec 14, 2009
I am using FC10. how do I change the resolution of the "Boot Up" screen? My monitor is 1024x768 capable but my boot screen is 1280x1024. I don't get anything until it finally loads X Windows. When my machine is booting up I cannot see the screen because my monitor can't handle it. When I hook it up to my other monitor (1280x1024 capable) I can see the boot up screen. I'd like to be able to see the boot screen in case there are any errors I need to se. How do I change it?
View 1 Replies
View Related
Oct 14, 2010
I have 4 NICs in my 10.04 server, 3 of which I have bonded. The bond itself is working fine -- I'm able to connect to and from the machine -- but whenever I try to ping out, I get duplicate replies. Google has, so far, yielded nothing of use.
I've included potentially relevant files:
/etc/network/interfaces
Code:
# The loopback network interface
auto lo
iface lo inet loopback
auto bond0
[Code]....
View 3 Replies
View Related
Mar 7, 2009
I have an Intel DG33TL MB, Intel Core 2 Quad Q9650, 8GB SuperTalent DDR2-800, and 4 Seagate 500GB hard disks. The disks are connected to a 3Ware 9650SE-4LPML and set for RAID0. I partitioned the drive in the following manner: 900GB for XP-Pro x64 (first install), 100 GB XP-Pro (installed second), and the remaining for FC10. After installing FC10 x64 using downloaded DVD .iso I am getting the following error on reboot:
Code:
Reading all physical volumes. This may take a while...
Volume group "VolGroup00" not found.
[code]....
View 1 Replies
View Related
Jan 25, 2009
I did a fresh install of Fedora Core 10 32bit on my Caompaq Presario AMD 64 laptop which originally only had Vista ultimate 64bit. When I go in to grub and choose windows I get a screen that says:
Windows failed to start...
File: windowssystem32winload.exe
Status: 0xc0000225
Info: The selected entry could not be loaded because the application is missing or corrupt.
View 9 Replies
View Related
Feb 17, 2011
I have been googling for three days, and I though posting to a forum would be more helpful than throwing my box out the window.
[Code]...
I was able to bond eth1 and eth2 together as bond0, but I am having problems with setting up two gateways on bond0. I can set one (eg ISP1) and all the traffic always routes through that ISP. Thus defeating the purpose of bonding. eth1 and eth2 pull an ip just fine and were able to ping the internet before bonding. Originally, I set the bond0 ip to the same subnet at my internal network, but I read that in order to set up nat you need to have the adapters on two seperate subnets.
Every time I fix one issue with this scenario something else breaks. I have tried dozens of different configurations. I am relatively sure that it is just a routing table issue, but I was wondering if anyone could point me in the right direction.
[Code]...
View 2 Replies
View Related
Feb 6, 2009
I'm currently running FC9 and I have no problem with my network connection. Now I just installed FC10 on another partition too try it out, but I don't seem to get it work. I disabled the NetworkManager (like in FC9) and enabled the Network. I'm using static IP, when in go in Network Configuration/Ethernet Device/General, the subnet mask is always taking the address of the Default gateway address when I press OK.
my subnet mask is 255.255.255.0, and my gateway is 192.168.1.1, but after I press ok they both go back to 192.168.1.1
View 3 Replies
View Related
Mar 21, 2009
I and my friend use FC10 on our laptops. We want to share our data by creating a wired network between our machines because a wireless router is something what our pockets can't afford. What should I do for it? What type of wires and stuffs do I need? I Googled for some link for doing so in FC10 but couldn't find.
View 6 Replies
View Related
Oct 20, 2009
I recently upgraded my x86_64 system from FC8-FC10 using Pre-Upgrade, and here I got some help fixing all the package conflicts that resulted. Following the first reboot after this massive package update, it appears DNS doesn't work in some apps.
I could ping www.yahoo.com, and nslookup www.yahoo.com resolved the name, but firefox and links couldn't. Typing the ip addr that nslookup gives for www.yahoo.com works fine in both firefox and links. Something's obviously wrong with DNS.
I found a workaround for Firefox which is to browse to about:config and set network.dns.disableipv6 = true. Firefox started resolving names after that.
But then I noticed yum is DNS incapable as well. I don't know how to fix it. Here's what I get:
Code:
[~]$ sudo yum update
Loaded plugins: allowdowngrade, refresh-packagekit
http://linuxdownload.adobe.com/linux/i386/repodata/repomd.xml: [Errno 4] IOError: <urlopen error (-2, 'Name or service not known')>
Trying other mirror.
[Code]....
Does anyone have any additional info on workarounds or fixes for this DNS problem?
The machine in question has a static ip addr, and I have static nameserver addrs in /etc/resolv.conf, corresponding to the static settings provided by my isp.
View 14 Replies
View Related
Aug 1, 2009
How can i run internet in FC 10(KDE). I have wireless lan card in my pc.
TPLink TL WN353G.
View 1 Replies
View Related
Mar 16, 2009
Since 2.6.27.19-170.2.35.fc10.x86_64, dhclient wlan0 doesn't seem to work any more.
However, bizarrely, dhclient eth0 does (to the same D-link wireless router).
The AP shows connected - tail /var/log/messages
No working leases in persistent database - sleeping.
WINXP connects just fine. This (B43) has worked nicely ever since FC10 came out, and I was able to use the WiFi at all kinds of places on a recent trip. Other than a couple of yum updates, I don't think anything else has changed since. Other devices on the wlan are getting their DHCP requests satisfied correctly.
Is anyone else having this problem since about a week ago? Perhaps there's something really obvious I'm missing. I can manually assign an IP address to wlan0, manually edit the routing tables and edit /etc/resolv.conf, and then Wifi seems to work OK, so it doesn't seem to be b43 itself unless it is dropping DHCPOFFERS. If this isn't a regression, does anyone have any tips about how to debug this?
View 3 Replies
View Related
Aug 4, 2009
my eth0 suddenly stopped working on FC10. i have been using it the whole time, and now it refuses to even ping the gateway. dhclient is not receiving a dhcp offer and when i put in the information manually, it is not even able to ping the gateway. netstat -rn shows that the destination of the router is going nowhere.
i do not think it is the hardware/software, but rather maybe the provider? i am from central europe but just moved up to great britain and working at a friends place. i can connect the mac powerbook without a problem (it will get an ip with dhcp), but not the linux machine.it is a normal ethernet modem connection here. can it be, that it checks MAC addresses or even the computer names? the powerbook also has a really weired IP address: 77.102.xxxxx
i am not using network manager, but command line tools and have nm uninstalled. does anyone have a clue, what this could be about? i am not a newbie, but this is really puzzling me.....
View 4 Replies
View Related
Dec 2, 2009
I have a Fedora 12 system that I am trying to configure with 3 IP addresses on one NIC card. I created scripts for each of the connections I want in /etc/sysconfig/network-scripts/ and they are called ifcfg-eth0, ifcfg-eth0:1, ifcfg-eth0:2. If I run /sbin/services network restart it configures everything as I would like. When I restart the computer the only device configured is eth0 and it is set to DHCP. If I run the script again everything works. What am I missing to make this change persistent?
View 2 Replies
View Related
Jun 2, 2009
I recently built my second general-purpose server, and recently installed fedora core 10 on it. The first thing I attempted to set up after installation was the network - and that's where it's gone wrong When editing a network device using the graphical system-config-network utility, I find that the subnet mask is being automatically changed to match the default gateway address every time I attempt to modify any of its settings (or sometimes even when I cancel the changes). This also means that I cannot set the subnet mask, as it simply won't accept my setting for it. I seem to be able to get around this glitch by setting the subnet mask using the shell version of the same utility, but that doesn't solve my network issue.
Even when I use the shell utility to fix the subnet mask, I'm unable to ping other computers or routers on the network even when ifconfig indicates that the desired ip address has been taken, and other computers on the network are also unable to see the server. I'm using a wired connection and a static IP address on a network with no DHCP.
View 14 Replies
View Related
Jun 20, 2009
I'm having trouble getting my wifi devices to work on my 128bit WEP network. I have a new Thinkpad T400, with an internal Intel PRO/Wireless 5100 AGN. I also have some cardbus cards: a Lucent ORiNOCO Gold, a Linksys Wireless-G, and a TRENDnet TEW-421PC. I have them set up as interfaces eth2, eth1, and eth3. (The TRENDnet isn't recognised as a network card at all, so no interface for it.) I have installed the latest firmware for the Linksys card.
The /etc/sysconfig/network-scripts/ifcfg-* files are virtually identical for all of them, differing only in the HWADDR and DEVICE lines. So here's the behaviour:
1. The Lucent card comes up just fine.
2. The internal 5100AGN and the Linksys cards won't come up, and watching with iwconfig shows that they're either associated with my AP OR they've got an encryption key set -- but not both.
3. When trying to bring up the 5100AGN, I get the following messages:
iwlagn: index 0 not used in uCode key table
iwlagn: index 3 not used in uCode key table
/var/log/messages shows DHCPDISCOVER requests being sent, but they're bound to fail since the association with the AP with WEP isn't being completed. And yes, the ifcfg-* files really *are* identical except for the DEVICE and HWADDR lines. The /etc/udev/rules.d/70-persistent-net.rules file correctly maps the interfaces to the MAC addresses. So why does my antique ORiNOCO card work and thew newer ones fail? How can I track down what's being done wrong/not being done?
View 4 Replies
View Related
Sep 30, 2010
I have two servers that have been running link aggregation and VLAN trunking for years. I've installed larger drives in one and done a fresh minimal install. In spite of configuring as before the network will not come up. I did discover that a minimal install will not install vconfig which was causing one particular error when the VLANs tried to come up and this has been solved by installing vconfig. However, at this point the problem appears to be not bonding eth0 and eth1. /proc/net/bonding/bond0 indicates: "bond bond0 has no active aggregator"
If I put the old drives back in and boot the old OS everything starts up fine. I was even able to get it working with:
modprobe bonding
ip link set dev bond0 up
ifenslave bond0 eth0 eth1
service network restart
however, it does not survive a reboot. Is the a bug in the 2.6.18-194.11.4.el5PAE kernel or the network scripts? The the previous kernel I am running is 2.6.18-128.1.10.el5PAE For what its worth, these are the configurations:
[Code]...
View 2 Replies
View Related
Mar 3, 2009
I have been running FC8 on this IBM T23 with a D-Link wireless adapter. Using MadWifi this has worked fine with Network Manager disabled. But now I have nuked that installation and replaced it with FC10. Network Manager is nice, and I would like to use it. And it kind-of works. Network Manager recognizes my router and all my neighbor's routers, but I can't connect.
[Code]....
View 5 Replies
View Related
Feb 15, 2009
I have an older laptop on which I have installed Fedora Core 10 (2.6.27.5-117.fc10.i686). I am using a Retail Plus Mini Wireless USB Adapter. I have scanned this forum and someone mentioned that support for this adapter should come "out of the box" for FC10. I have a fair amount of experience with Linux command line configuration but am by no means an expert. I have absolutely no experience, however, with wireless.
NB that via iwconfig I get the output below which is giving information about my (currently for now unencrypted) SSID called "activity_logged". Pardon my ignorance but wouldn't this mean that I have wireless enabled and if so how does one access it through the command line? I would also eventually like to go back to encrypted status and access that via command line.
[Code]...
View 5 Replies
View Related
Mar 13, 2011
I use Fedora 13 x86_64. Recently i installed q4 wine and booting froze with message "registering binary handler for windows applications". Then on removing q4 wine boot froze at "unexpectedly disconnected from boot status daemon".I also removed wine, smolt.
[Code]..
View 1 Replies
View Related
Aug 6, 2009
I want to configure my ADSL but I don't know what should I do. Can you explain me How can I configure it?(I use fc10, ethernet cable <Asus Am608 ADSL modem)
View 9 Replies
View Related
Apr 10, 2010
I am having problems with bond0 starting at boot on ubuntu server 9.10. After I do a restart I have to manually start the network with "ifup bond0". I have installed the built package (ifenslave-2.6_1.1.0-15ubuntu1_i386.deb (as indicated in Bug #482419)).
I have setup bonding for mode=6 with miimon=100 using eth0 and eth1 (both are Intel 10/100/1000 ports using an aic79xx network driver).
The contents of the aliases file are:
alias bond0 bonding
options bond-mode=6 miimon=100
The contents of the interfaces file are:
auto bond0
iface bond0 inet static
address 192.168.15.60
netmask 255.255.255.0
gateway 192.168.15.1
slaves eth0 eth1
bond-mode 6
View 9 Replies
View Related
Jan 4, 2011
Ubuntu 10.10 doesn't boot at all. The liveCD only boots once every like 30 attempts, installing from liveCD froze, but the Alternate CD worked and installed ubuntu. Now when I try to boot into it using GRUB, it freezes at the beginning of the boot process.With normal boot it freezes at line: Starting AppArmor profiles Skipping profile in /etc/apparmor.d/disable: usr.bin.firefox.With recovery mode it freezes even before showing me anything
A little kinda like the liveCD, if I try like 30 times, it might manage to boot once in normal mode.That line keeps on repeating, the the xxx.xxx integer changes each time, and this goes on forever.I tried removing my floppy drive, but it didn't help.I tried to boot with fd0=noprobeThe one time it booted, when I restarted, it froze while trying to restart.
View 9 Replies
View Related
Apr 27, 2010
I've got a server that has bond0 and bond1 setup. I'm documenting some things in case I need to failover and bring up my secondary server up as primary... I just need to know if simply creating the interface ifcfg-bond0:0 with a new IP address obviously of the crashed system,,, is all that needs done or do I need to load bond0:0 module in /etc/modules.conf also?
View 1 Replies
View Related
