Fedora Networking :: Cannot Connect To Internet (Netgear Router)
Apr 27, 2010
I cannot connect to internet. I just installed Fedora 12 w/ the Live CD and I have a Linksys WMP54G Wireless Card (v4.1 I believe) and it apparently installed fine upon install of fedora. It will not thought connect to the internet. It reads my connect (NETGEAR-2.4-G), my router is a Netgear WNDR3300. It worked perfectly fine on Windows XP. Like I said, it picks up my wireless connection. But when I go to connect it attempts to connect for like a minute or two then goes back to not connected.
View 3 Replies
ADVERTISEMENT
Apr 24, 2011
running ubuntu 10.10 on a toshiba laptop recently the wireless Internet stopped working from our netgear router, it still works for the Ienova laptop and emachines desktop using the router but this laptop will not work wirelessly internet cuts in and out on this laptop when on wireless when it didn't previously do so it reads a connection but will not load up web pages unless hard wired in with an ethernet cord.
View 3 Replies
View Related
Jan 1, 2011
I have internet access through 3G/4G USB dongle direct into my Ubuntu 10.04 box. Works great! Now I would like to share this connection out through my Netgear WGR614 wireless (and wired) router. Any clues? I've tried the simple (GUI) instructions using Network Manager, but just can't seem to get it right. Previously, I had DSL and this plugged nicely into the WGR614 and internet and ethernet access was had by all. Now, I'm a bit confused on how to get the sharing (ethernet and wireless) between my Ubuntu box and the wired/wireless network while at the same time getting Internet access to all through the Ubuntu box.
View 2 Replies
View Related
Jun 18, 2011
I want to set up a Linux box as a wireless router to replace our existing Netgear WNR1000 router, as I believe the Netgear does not support the coming IPv6 protocol. Unfortunately, it is not flashable with OpenWRT or DD-WRT presently.
As we have Comcast, our cable modem acts as a dumb modem according to the customer support guy I talked to, and our router is the one that asks for the IP address from DHCP. Thus, when Comcast switches over to IPv6, I don't believe my existing router would work, correct?
My idea is to take a Linux box and put two NICs and a wireless adapter in it, using IPCop or Smoothwall to set up a router. I could then enable IPv6 support for when we have IPv6 with Comcast. Is that possible? Would there be a way to get BIND to hand out private IP addresses in the same subnet on the both the LAN NIC and the wireless card?
View 1 Replies
View Related
Apr 6, 2011
I am trying to setup a dhcp server for my internal network. I have two NICs, a modem, and a wireless router. I have my server connected directly to my modem which is providing me with Internet access on eth1 and is working fine. I have dhcp and dns setup on eth0 which is connected to my router. The router shows that it is connected to the Internet but when the router gives a client computer an IP address, the client is unable to connect to the Internet but can connect to the router. I will post my configuration files below with my current configuration.
[Code]....
View 5 Replies
View Related
Jul 30, 2010
I connect my internet using pppoe to may DSL modem with bridging mode, and it goes fine until I try to put a wireless router between my PC and the modem. After I configure both modem and the router, I can run my wireless network fine by connecting it from a laptop, but my PC is unable to reach the modem at this configuration.
PC has address 192.168.2.100
Router has address 192.168.2.2
Modem has address 192.168.2.1
all with netmask 255.255.255.0
With bridging configuration in modem and automatic detect configuration in the wireless router, the wireless network run well, except the PC cannot ping the Modem saying that
Code:
root@firefly:~# ping 192.168.2.1
PING 192.168.2.1 (192.168.2.1) 56(84) bytes of data.
From 192.168.2.100 icmp_seq=2 Destination Host Unreachable
Looks like my PC, which has Slackware 13.0, don't know how to reach the modem even they are physically connected.
1. how can I configure the modem, PC, and router so that the PC can reach the router? Do I need to do add route gateway from the PC?
2. How can I configure internet connection from the PC (before I use PPPoE)?
3. How can I configure the modem, PC, and router so that the wireless network is on?
View 7 Replies
View Related
May 23, 2010
I'm a beginner in Ubuntu, I'm using Ubuntu 9.10.
Currently using a Dlink GLB-802c router and using a ADSL connection. I try to connect to the Internet but it is unsuccessful. Ubuntu is not indicating my router when I connect to the PC.
My PC is P4 and using USB to connect to internet, PC haven't a Ethernet interface.
View 1 Replies
View Related
Jan 3, 2011
- CAN connect to other computers - ssh and vnc over the home network (via D-link 524 router).
- CAN get an IP address via DHCP
- CANNOT get internet connections - including router at 192.168.0.1
- CANNOT even ping router (but I get an IP address - weird)
- Other computers on the network CAN access internet
- Live CD could not access internet
results of ifconfig
Code:
Code:
I am wondering if his ISP could be doing this - he has received a warning letter about bitorrent. Could the isolate a single computer behind a NAT router?
This is the results from dmesg:
Code:
I have tried:
- to set proxy settings as "Direct internet connection"
- disconnecting power to (including 30 sec wait): modem, router, computer + unplugging ethernet from computer
- Live CD (he only had an old one 7.10) which also didn't connect to internet, but as I am remote, I couldn't do any more. We are downloading a 10.04.1 iso for him to burn tomorrow, and will try that again.
- Uninstalled Crashplan which was the last software that we installed (and it was working ok).
I am currently ssh'ing into another computer on the network that IS working, and then ssh'ing into my Dad's computer - including a VNC session (tunneled through both machines and router).
View 5 Replies
View Related
May 4, 2011
i recently connected this router to mahh modem..http:[url]....before router connection i was able to connect to internet via "pppoeconf command" but now i am not able to connect to internet from ubuntu ..i am still using lan cable coming out or router to connect it with pc..
View 2 Replies
View Related
Oct 4, 2010
AT&T will not help. I am trying to connect with Cable (CAT5). When I try to configure my network card with YaST here is the message received. "Unable to configure the network card becasue the kernal device (eth0, wlan0) is not present. This is mostly cause by missing firmware (for wlan device) See dmesg output for details"
View 2 Replies
View Related
Feb 12, 2010
Useing gnome network manger. I thught that is DNS resolve problem, and wrote in linksys router the same DNS as 3g huaweii modem use. Steel the some result. NO INTERNET. Change for static ip in router and try use the same gatway , but steell can't use connected at the same time to internet with 3g and local router.
Only one devace at the same time, Router have no any acces to internat. SO why 3g internet stoping working after connecting router to LAN ports? Has it some thing to do with subnet or ip range and routing table?
View 1 Replies
View Related
Oct 27, 2010
At work, we (like almost everyone) are still full-on windows. I am currently trying to get away from windows because I am not a fan. my current windows machine (different from my Ubuntu machine) is accessing the wireless network fine, and there are no obvious problems there. Also, my Ubuntu machine can access my wireless network at home, so I know there are no driver issues. I set up the connection for the Ubuntu machine, and it seems to be connecting OK. I can ping internal IPs and by all statuses, the connection to the router is functioning. However, when I attempt to load a web page or ping a domain or external IP, it fails. I tried to ping the IP, thinking if that worked, it's probably the DNS, but pinging both domains or IPs fails. I have looked around at forums and posts, but none of them seem to match my issue (that's probably not true, but I am struggling to see the commonality).
Here are the results of "netstat -r":
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.45.0 * 255.255.255.0 U 2 0 0 wlan0
link-local * 255.255.0.0 U 1000 0 0 wlan0
default 192.168.45.5 0.0.0.0 UG 0 0 0 wlan0
And here is "ifconfig":
wlan0 Link encao:Ethernet HWaddr 74:f0:6d:XX:XX:XX
inet addr:192.168.45.49 Bcast:192.168.45.255 Mask:255.255.255.0
inet6 addr:fe80::76f0:6dff:XXXX:XXXX/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]....
View 3 Replies
View Related
Jan 7, 2011
After forgetting my wifi router password, I had to reset and reconfigure the router. I enabled WEP, and after I typed the password, the computer now recognises it automatically. But I can't connect to the internet no matter how long I wait. (The wired internet connection works fine.) How can I get the wifi to connect to the internet?
View 1 Replies
View Related
Aug 2, 2011
I think something weird is going on. On a fresh installation of 11.04, I seem to be connected to my router just fine, but I can't reach the internet or anywhere else on my network. Anybody see my problem from what I've posted? The computer is only connected via wireless (so I don't know why eth0 would be connected as well). I can't think of what I'm missing...My system seems to be connected to my router on two interfaces. "ip addr" gives:
Code:
1: lo <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
[code]....
View 9 Replies
View Related
Feb 12, 2010
I have just installed Linux Mint 8 to an Asus A6000. My problem is that the computer won't connect with my wireless router. I have tried with MAC-adress and such, but still no respons. I also tried to connect with a cable to my modem, but no response there either.
I think I may lack some drivers, to what I think is Broadcom b43, but I am not sure. I tried to download the drivers on my other computer, and transfered them to the Asus. I managed to install 2/4 drivers, but on the two others, I get this message "Failed to fetch ... Couldn't reach archive.ubuntu.com"
View 2 Replies
View Related
Jan 31, 2010
I've only been using linux for a few days so I don't know all the tricks. I'm pretty savy configuring windows networks however.My adapter is (according to windows) a: CNet PRO200WL PCI fast ethernet adapterLinux says it is a: 21x4x DEC-tulip compatible 10/100 EthernetI do seem to be getting an ip address from the DHCP router, but I cannout ping any other ips or connect to the internet.I've tried a bunch of different options, switching things back and forth, but it still doesn't work, and honestly i don't even know what some of the options mean.
ALSO, if this helps:
paladin:~ # ifconfig eth0
Eth0 Link encap:Ethernet HWaddr 00:08:A1:03:3C:99
[code]....
View 14 Replies
View Related
Dec 5, 2010
I have just installed ubuntu 10.04 using the wubi installer to dual-boot my machine. Under ubuntu, I am not able to connect to the internet or my router. Everything works fine under windows. I have tried to find relevant information in the forums, but nothing seems to work for me. I have tried disabling ipv6, setting a static ip, but no go. ifconfig shows no IP, dhclient results in no DHCP offers and pinging my router's IP results in Network is Unreachable.
View 9 Replies
View Related
Apr 1, 2011
I have 2 pcs at home. I dont have a switch so I can connect only one PC at a time to my adsl router/modem for internet access. In the past I had successfully connected the two PCs (NIC to NIC) to each other using the same ethernet cable which was supplied with my dlink adsl modem.
Recently the motherboard of on of my PC went bad so I replaced it with a new one. The problem is when I connect the two using the same Ethernet cable they won't connect. The lights on the Ethernet port won't light up. I can still connect both of them to the adsl router (NIC to Router) (one at a time).
View 5 Replies
View Related
Oct 27, 2010
I have a telephone connection of 1 mega internet modem huawei mt 880 SmartAX my desktop computer is connected via an ADSL PPPoE.I use Ubuntu 10.04 in Spanish and want to know how to connect a WiFi router TP-LINK TL- wr942nd to provide wireless Internet to other 2 PC, a desktop with a plaquet wireles G CNet CWP-854 and 500 series notebook olivetti olibook. The issue is that when I connect the router I can not even go online and do not know how to operate the network, I can not even connect the desktop to my internet provider
View 1 Replies
View Related
Jan 1, 2010
I installed Ubuntu 9.10 netbook remix on my Acer Aspire One D250 computer. The broadcom wireless NIC succeeds in connecting to the network but only if I remove the WPA-PSK security in the Netgear router settings. What do I need to change in order to be able to secure my network?
View 2 Replies
View Related
May 18, 2011
how to set this baby up with a working Internet connection so I can get on my PS3 across the other room.
View 1 Replies
View Related
Dec 29, 2010
I have a client that has a basic network that uses comcast cable. He bought a NETGEAR N300 wireless router which has a 192,.168.3.X network and he attempted to add it to his 10.10.10.X network and all is fine. He laptops and such can get to the internet fine. The issue is he cannot get to any of his devices on his 10.X network. I have looked at his comcast router which is controlling his 10.X network to see if I can add addition routing to his 192.X network. but didnt see anything. I also am not to familiar with the N300 wireless router. I was going to have the wireless DHCP turned off and some get it to pull the DHCP stuff from the comcast side but dont see any area to do this.
View 2 Replies
View Related
Jul 12, 2010
I have a Netgear DG834 ADSL router (v3) which I have used for a couple of years. Prior to that I had a v2 of the same router, but upgraded for the one that supports ADSL 2+ (here in the UK).
Recently I have been having problems with the connection often being dropped, and when I access 192.168.0.1 for the router admin page, when it is not working I get no IP address listed for that of the ISP's server, and sometimes as well the upstream and downstream speeds are listed as 0 kbps.
Usually this was resolved by rebooting the router.
However, for the last couple of days, when using Ubuntu 9.04, the page of the router at 192.168.0.1 will not load. I have tried numerous different browsers, and none of them will give the router admin page.
When I tried booting from a live CD of Fedora 13, the router admin page came up just fine, no problems (although still not getting a proper connection to the Internet).
I was going to try to use the older router I had, but so far, as I cannot access the router admin page in Ubuntu, I have not done so (not had the time, and now I am at work posting this).
So there must be a problem in Ubuntu that is preventing it showing the router's admin page. The Network connection details show that the router has given the PC an IP address of 192.168.0.6 and the DNS servers are listed, so I know that Ubuntu is talking to the router, but it is not allowing me to access its settings in any way.
View 1 Replies
View Related
Jan 12, 2011
could set up a firewall on my linux machine? I have is to connect my router wired to the linux machine and then from the linux machine to my main computer, and obviously routing the internet connection through the linux box as a firewall. I use a Netgear DG834G router
View 9 Replies
View Related
Mar 19, 2011
For my broadband Internet I have several computers connected by cable to a Netgear DG834Gv5 router which has its own firewall.I have the wireless turned off by choice.My desktop and laptop are Linux only. (Ubuntu lucid lynx) I use the same username and password (very strong password) on both.What I want to know is can I set things up so I can browse and copy files between the computers using say nautilus on either computer?if not nautilus then I would happy to be able to do the same via a terminal window.I am not necessarily wanting to be told how but either what to Google for or where to find it.
View 2 Replies
View Related
Dec 27, 2009
i am trying to compile netgear wgr614l sources.i am using fedora 11 [leonidas] for compilation. system core is 2.6.29.4-167.fc11.i686.PAE.
View 12 Replies
View Related
Nov 4, 2010
I have managed to connect to the above NAS using the supplied RAIDar software from my base unit. The unit is duel boot with Ubuntu 10.10 and Windows XP. Both operating systems work with the NAS both by wireless and wired using RAIDar and any other relevant programme
However my laptop, running Ubuntu, will not find it using Raidar, the IP address in a browser nor with a file manager or any other programme. I have tried both wired and wireless connections
However if I go to "places" from the top bar, which opens Nautilus, I can access it and all the files on it.
View 1 Replies
View Related
Aug 10, 2011
I've been searching for help on this issue, and I've tried some things, but I can't get my connection to work.I can see the available networks, and the LED on my device is on, but when I try to connect it can't connect and asks me for the network security key again.I've installed and run the ath9k-htc installer, but I noticed no change when I did so. Is there a step I'm missing?
lsusb:
Code:
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 047f:c001 Plantronics, Inc.
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
[code]...
View 9 Replies
View Related
Feb 16, 2010
I have a question. I just bought an internet router which also has wireless connection and my notebook also has wireless LAN.I was able to connect the computer to the internet router very easy. But i dont know how to make it work wirelesss under fedora linux 12...i mean how should i setup the connection to the router so i will be able to have a wireless connection?
View 4 Replies
View Related
Aug 28, 2010
My set up: Roku digital video player n1050 (it does not look like the ones in the manuals I have found online, and there was no manual in the box--this only has the red, white and yellow jacks on the back, plus the places to plug in the ethernet and power cables; reset is on the bottom)
Wired network Netgear wnr854t Router assigns ipaddresses to devices attached to it Production environment 7 computers regularly access this network wired 1 additional computer regularly accesses this network both wired and wireless I am posting this going through this router, so you can see it is working
Symptoms:
Power up Roku with ethernet connected In set up, I chose wired connection Roku finds the ethernet cable Roku cannot find the local network and stops Router can see the Roku box, and says it is attached as 192.168.0.7 I can successfully ping the Roku box, but not ssh into it. I can telnet into the Roku box using telnet 192.168.0.7 8080, but I do not see anything I can do from there.ng knowledge!
View 1 Replies
View Related
