I have been trying to install the FGLRX driver for a Radeon HD 4850. According to this page and others on the web, it says that Xorg 7.5 isn't supported by the driver. I was just wondering is it possible to install Xorg 7.4 on Fedora 12, if not what release of Fedora should I use (i.e does Fedora 11 support Xorg 7.4?)
View 2 RepliesI realize that Canonical is not responsible for the Catalyst driver, but I can't seem to operate outside of the Ubuntu Classic (no effects) mode for 64 bit Natty, and I was curius if anyone else had encountered or resolved this.
When I upgraded from 10.10 (I was using the fglrx package), xorg would immediately crash. I was able to reach the gdm screen only using recovery mode. I uninstalled the fglrx package, and now I can boot into Ubuntu Classic (no effects) mode only (no other desktop will work) using the open-source driver at no greater than 1280x1024.
When I try to re-install the catalyst driver using aptitude or Administration->Additional Drivers, the installation fails:
(jockey.log: WARNING: modinfo for module fglrx failed: ERROR: modinfo: could not find module fglrx)
Similarly, package generation from the AMD page fails:
Installation complete.
*** glibc detected *** ./setup.data/bin/x86_64/setup: double free or corruption (fasttop): 0x000000000259f630 ***
======= Backtrace: =========
[Code].....
After installing OpenSuse 11.3x86_64 specifically for the ATI radeon HD 4850 proprietary driver that was created with intended compatibility from ATI, I have intense screen tearing.
View 4 Replies View RelatedI try to connect my graphic card with my TV. I have ATI Radeon 4850 card with 7 pins S-video output and I want to connect it my TV using s-video to RCA cable (the RCA output is yelow, red and white, I assume the 7 pins has audio signal as well).
My card doesn't have problem when connect it wit my monitor via DVI, but the S-video out is not detected. How can I enable it? Can I configure the card from KDE? If so, how?
I'm using the driver from Slackware package and I'm using Slackware 13 stable 64.
I am currently running Linux Mint Debian Edition (based on Debian Testing). I have installed an ATI Radeon 4850 w/ 1GB RAM. I am using FGLRX, and Catalyst Control Center seems to be working. However, even though I have selected "Override Application Settings" in CCC, I get no AA whether it be during gaming (Urban Terror) or in Compiz (3D Cube).
View 3 Replies View RelatedIs this card supported in Squeeze by either the non-free firmware or the proprietary driver? I just got one to stick into an older box that will be going to a college girl that wants the 3D desktop in KDE. The built-in video was a joke and wouldn't even work without compositing. It was one of those crappy, non-standard pieces of crap known as a "Unichrome" (not the pro).
View 10 Replies View RelatedAfter upgrade to Lynx, all of my ATI drivers don't work. Whenever I try to run fglrxinfo I get " Segmentation fault " And for fgl_glxgears I get" Using GLX_SGIX_pbuffer Segmentation fault " For sudo aticonfig --initial -f " Uninitialised file found, configuring.
Using /etc/X11/xorg.conf Saved back-up to /etc/X11/xorg.conf.fglrx-11 " Compiz does not work at all either.
i am gonna to buy a new noetbook hp probook 4510s one with ATI Mobility Radeon HD 4330 graphics card is that card compitable with fedora 12 ?
View 10 Replies View RelatedI am running Kubuntu 10.04 LTS and have had no problems with my ATI card up to kernel 2.6.32-29. Upon update/upgrade to 2.6.32-30 the FGLRX driver will not load graphics and I can only get the text system login. If I reboot to -29 everything works great.
View 2 Replies View Relatedi was recently trying to run some opengl apps on ubuntu, and installed new drivers for intel. The problem is that now, every time it reaches login screen it crashes. I'd like to remove it, but i can't. Recovery console asks for root password. Is there a way to do it from a livecd?
View 1 Replies View RelatedI need a quick answer if possible, is it better to remove the proprietary drivers before upgrading to 10.04 from 9.10? Or should i have the open source drivers installed? A clean install is not an option on this machine.
View 3 Replies View RelatedUPDATE 8/28/2009: I now recommend that people install the new packages instead of the manual instructions below, see this link:http://forums.fedoraforum.org/showthread.php?t=155503 (Howto for fglrx/catalyst (Ati driver) and Compiz-fusion)NOTE: After installing the packages, I had to do the things at the following link to make the above packages work:http://forums.fedoraforum.org/showpo...postcount=3564If you still want to install the driver manually (you do not need to if you install the packages above), the instructions are below:
Fedora 11 ATI fglrx driver manual install notes
Updated: 10/12/2009
========================================
[code]....
I have a problem with the Radeon 5670 and the fglrx driver in opensuse11.2. I've created a rpm from the newest ati*x86_64.run (catalyst10.2, witch should support the radeon 5600 series) and installed it following the "ATI-the hard way" instructions. Here is the resulting Xorg.0.log:
Code:
X.Org X Server 1.6.5
Release Date: 2009-10-11
X Protocol Version 11, Revision 0
Build Operating System: openSUSE SUSE LINUX
Current Operating System: Linux sissipc 2.6.31.12-0.1-desktop #1 SMP PREEMPT 2010-01-27 08:20:11 +0100 x86_64
Build Date: 02 November 2009 12:04:43PM
[Code]...
"PCI bus 1 card 5 func 0" seems to be the Onboard-Graphics (Radeon 3200) and "PCI bus 2 card 0 func 0" i think is the Radeon5670 set as primary graphics adapter in the BIOS
I've been using fglrx since 11.3 came out, and I just upgraded to 11.4 today and noticed that my graphics card is now supported by the open-source radeon driver. I was trying to switch, but was never able to properly switch the driver and get radeon running. I've read many of the help pages, but still am unable to actually get radeon working.
Perhaps I'm missing something, such as not properly removing fglrx, but I'm not too sure.
I'm having trouble getting back Desktop effects when I try to go to the radeon drivers from fglrx. It worked when I first installed and it works on a live cd. My main reason for going back is because A. Brightness settings don't work on my laptop with fglrx. and B. Gnome-shell isn't working with fglrx.
I have a radeon 3100 (I think).
I installed the fglrx drivers in Ubuntu Natty for a ATI Radeon HD 4350 graphics card. Although compiz seems to work better, everything seems to be a blurry as compared to the generic graphics or while under Windows 7.For example, every other line displayed here while I type is more blurry than the others.I have a dual screen setup.
View 2 Replies View Relatedcoming back to linux after a few years away and I'm trying to get it set up on my Asus G73JH laptop. Problem is the closed-source drivers aren't playing nice. I can get it to start with the "radeon" driver but when I try to use fglrx, either through a manual xorg.conf change or aticonfig, I get a black screen (or a couple times a white blob moving across the screen) and then the system hangs. The biggest problem with this is I can't access the output from the X server and nothing is being written to the log files (probably because I have to hard-reboot). I've googled and read just about everything I can and I'm pretty much lost for ideas now. I'm not too good with troubleshooting Linux since it's been a while but there are a couple things that would be really helpful to me: a way to save whatever X puts out before the system hangs and a comparison from someone who plays decently graphics-intensive games between fglrx and the open source driver because I don't mind using the open source drivers as long as performance is comparable. Any extra information I can post I will as requested but I think being able to review the X output is a good place to start!
View 7 Replies View Relatedi tried setting up fglrx driver for my card using the steps outlined here: wiki.debian.org/ATIProprietary
but when I get to the step where it tells me to use aticonfig i get this error: Code: aticonfig: No supported adapters detected I tried to make xorg.conf myself by doing what it says and making this the xorg.conf file:
[Code]...
but X won't start if I do that (delete xorg.conf and it goes back to it's fglrx-less state) However, I was successfully able to install the drivers on my Ubuntu install (different partition on the same machine) but not my Debian install.
How unistall fglrx and vga driver and restore to debian with out vga driver.like new debian with new install.
View 2 Replies View RelatedI've set up this new PC, the graphic card I picked is the ATI R7 260X, pretty good card with lots of core processors, high clock and 2GB memory. I'm now currently using the 14.4 catalyst drive, it works actually alright, though, there are some mishaps with this driver:
First my hdmi screen had scale down, leaving black borders around, even though the catalyst control said the correct native resolution, this turned out to be a underscan that fglrx does and I've finally managed to fix it. Other caveat is that the screen simply won't suspend or turn off( via software), DPMS actually works, forcing it turns the screen blank for some seconds but something does not allow the screen to sleep.
Performance wise it seems pretty good though, everything is pretty smooth, being able to play games maxed out on resolution and ultra settings, though, I still haven't tested out that many games.
The open-source radeon on the other hand, well its open-source, fully xorg and linux compatible, which is a major plus point. It seem it has come a long way, supporting lot of features and providing better performance in some cases.
Before installing Catalyst I had issues with mesa and steam, steam would complain about not finding the 32bit libraries, this is however a steam runtime issue, maybe it could already be fixed.
I'm owning an old single Core AMD (Opteron 148, like Athlon 64 3200+), it can't play h264 1080p-Videos without framedrops in active scenes. I'm also owning an not so old AMD/Ati Radeon HD 2400. It's not an UVD2 card, it's not even UVD+, its UVD i.e. UVD1. All articles regarding GPU h264 decoding I've found so far are saying "for vaapi gpu decoding on linux you need to have a UVD2 card". That's wrong! My UVD1-Card is playing fine some demo movies.
Setup:
Ubuntu "Lucid" 10.4
"deb http://ppa.launchpad.net/nvidia-vdpau/cutting-edge-multimedia/ubuntu lucid main" in /etc/apt/sources.list.d/cutting-edge-multimedia.list
[code]....
(With the original Ubuntu Lucid fglrx (8.723) there's some error, I don't remember the words. It doesn't work for me)It's working. I can play h.264 HD Videos with mplayer and decode it with a Radeon GPU. vlc 1.2 not working so far. It seems it's decoding fine, but screen remains green. Here's a screenshot, no fake! It's a two Monitor setup with fglrx' big Desktop. On the right there's running a movie Trailer (I Am Legend) and on the left there's some status info. Quality is not perfect (as you can see, horizontal displacement), but it's basically working.
I've always had and used Ubuntu. When I installed and did not like the stability of a certain version, I just reformatted the partition and used LiveCD. OK, on a virgin SATA, 300-gig partition, I installed 10.04 and that took the ATI Radeon 3rd-party graphics driver. No problem. Then, the family wanted 2 languages on the machine. The German keyboard screwed me in terminal and I wiped out Home and all their data. I used Scalpel to image-carve 300-gig onto a 400-gig partition and tried to re-install Ubuntu 10.10.
The ATI's fglrx will not install, that's the error. That same file prevents upgrades of Ubuntu to current status.
is this thread current for my problem with 10.10?
http://ubuntuforums.org/showthread.php?t=651566
Or, do I have that 400-gig with the backup cross-pollinating?
I am new to Ubuntu for the most part, but have done a lot of research on this OS. I just freshly installed version 10.10 32 bit, and the first thing I did was follow this tutorial on installing the drivers for my HIS Radeon HD 6850. I really want to get this drivers working so I can use the 3D effects on this OS.
When I type fglrxinfo I receive:
X Error of failed request: BadRequest (invalid request code or no such operation)
Major opcode of failed request: 136 (GLX)
Minor opcode of failed request: 19 (X_GLXQueryServerString)
Serial number of failed request: 14
Current serial number in output stream: 14
When I type aticonfig I get:
aticonfig: No supported adapters detected. The proprietary driver was never installed so I know that driver is not interfering. Originally the aticonfig was not found at all but with a little troubleshooting from the link above It seems to work, but obviously not recognize the card. The card works great on my windows 7 setup. If I can't get this working I may just remove Ubuntu all together, but any help would be amazing!
Card is the Radeon x300 and in the past in a wubi install I installed the propreitary ATI driver. I'd like to do that with this installation too. I've located the proper driver and tried to run in the terminal.
I get this error:
I've read were I have to uninstall the xorg drivers and make a .deb package but idk how to do that.
Can't get it to work. there is a driver at the amd website that i installed and it made my screen go #@$%@@#@@@!!!!##!#!$$#fV><$%$54
View 1 Replies View RelatedI've got a machine with an HD 4650 and the natty live cd ends up not in unity. I've got an even older machine with a radeon xpress 200 and unity works just fine from the live cd on it. Any ideas? I didn't want to install it; I've currently got lucid installed on it.
View 9 Replies View RelatedThe screen goes black while "waiting to populate /dev/"and only by adding acpi=off can I boot into my system, and then I see that I get an error message during boot when "populating /dev/ " that says"fatal error during GPU init", even after I've installed the firmware-linux-nonfree.deb, which is the one for the R300 family, which I'm guessing is the right one, since lspci tells me I have:Radeon IGP 330M/340M/350MI've read the wiki[URL]
View 5 Replies View Relatedwho has installed these drivers on ubuntu will help me to install ? Because I can not coped...
ati mobility radeon x1400 driver
need me 32bit driver... I found only 64 ...
Im having some issues installing the ATI Radeon Drivers. The card is a Radeon 9550
Code:
openbox millsm # sh /home/millsm/ati-driver-installer-9-3-x86.x86_64.run
Created directory fglrx-install.k7SnEv
Verifying archive integrity... All good.
Uncompressing ATI Proprietary Linux Driver-8.593
ATI Technologies Linux Driver Installer/Packager
which: no XFree86 in (/sbin:/bin:/usr/sbin:/usr/bin)
Error: ./default_policy.sh does not support version
default:v2:i686:lib::none:2.6.34-sabayon; make sure that the version is being correctly set by --iscurrentdistro
Removing temporary directory: fglrx-install.k7SnEv this is the current
Code:
>> @@ Package: x11-drivers/xf86-video-ati-6.13.0 branch: 5, [repo_sabayonlinux.org]
>> Available: version: 6.13.0 ~ tag: NoTag ~ revision: 2
>> Installed: version: 6.13.0 ~ tag: NoTag ~ revision: 2
>> Slot: 0
>> Homepage: [URL]
>> Description: ATI video driver
>> License: MIT
Code:
openbox millsm # emerge -av x11-drivers/ati-drivers
* IMPORTANT: 2 news items need reading for repository 'gentoo'.
* Use eselect news to read news items.
These are the packages that would be merged, in order:
Calculating dependencies... done!
emerge: there are no ebuilds to satisfy "x11-drivers/ati-drivers".
* IMPORTANT: 2 news items need reading for repository 'gentoo'.
* Use eselect news to read news items.
openbox millsm #
Distro is Sabayon 5.3G
I have acer laptop with ATI Mobility Radeon HD 5470 graphics card. I have downloaded ATI Radeon 5xxx driver from ati official site. When I ran it using the command below, it gives me the following error
command:
Error:
Removing temporary directory: fglrx-install.OiFpw4