I've burnt the fedora 10 Installable Live CD on to a DVD, the initial boot/menu's works fine but after the progress bar loads the display on the next screen loaded is all out of wack bad resolution etc, I can see a mouse cursor.
View 3 RepliesI tried Wubi, and all is fine, but when I choose Ubuntu on the boot menu, it shows some dialog, then just blank. its stays blank forever, so I had to shut the computer off.Then, I burned the Ubuntu iso to a CD and botted from it at startup. This at least showed the purpl-ish install screen. After I pressed enter over install, it went to the blank screen again. just black, nothing appeared.I'm not sure what the problem is. My laptop is fairly new, it shouldnt be having an issue to run it.I have 4Gb RAM, plenty of space on the hard drive, and a 1Gb video card...I have no clue what to do, as this is my first encounter with an Linux distro ever. help?
View 6 Replies View RelatedI installed F14 from my usb according to the wiki page using unetbootin. The usb boots perfectly and i get a working F14 system. I partitioned my HD with gparted and got a /,/home and swap partition, then used the installer to install the system using them. The installer finishes without a problem and ask me to reboot. When I reboot , there is a blank black screen. No grub menu , no fedora loading. I reboot with the usb and the partitions are full with the files from F14 , there is no xorg.log in the /var/log/ so f14 doesn't even start so the problem seems to be with grub.
I check the grub.conf in /boot/ , i set the timeout to 5 secs , i check that the kernel is using nomodeset (according to this wiki page there is a problem with ati), xorg.conf is using vesa as a driver and I reinstall grub with grub-install with no problems.My notebook is a acer aspire 5552 , i don't think is a hardware problem because I've used arch and opensuse with no problems in it. Fedora seems a nice distro , but this error is preventing me from using it.
I have windows 7 and ubuntu on my computer they were working fine together, so i decided to get fedora. now when i go to the boot menu on fedora it has a list that says fedora (numbers), and other. so i clicked on "other" but it says partitions were not found.
View 7 Replies View RelatedChanged the partition sizes = all ok
boot to F15 = ok
#grub-install /dev/sda = seemed ok but XP not shown
[code]....
I know this is an Ubuntu Forum (duh) but I'm having trouble booting Fedora. I have Windows 7 and Ubuntu 11.04 loaded on to my HDD and GRUB boots both of them just fine. I installed Fedora 15 on dev/sda7 (a clean partition) and I'm using the same swap for both Linux distros. I am not that new to Linux but I still need fairly detailed instructions.
My problem: Fedora does not show in the boot menu and I'm not sure how to get it there.
I've heard about something going funny when the kernel updates and something about chainloading but I'm no expert on either.
I have a /boot partition, and the online update process has downloaded the upgrade to /boot/upgrade. The problem is that grub is actually booting from a directory /boot which is in the root partition, but is invisible once the machine has booted, because the /boot partition is mounted over it. The result of all this is that the upgrade option does not appear in the boot menu, because that option has been inserted in the menu.lst (or grub.conf) in the /boot partition. is it ok for me to run:grub-install /dev/sda4(that's the device that contains the /boot partition where the upgrade menu option and data). Also, do I need the --root-directory option, given that the boot directory is the root directory of that partition.
View 3 Replies View RelatedI'm trying to install Fedora 15 from a USB stick. I can boot off it just fine, but most of the menu options don't work:
Boot => Freezes indefinitely
Boot (Basic Video) => Freezes indefinitely
Verify and Boot => Freezes indefinitely
[code]...
Debian if my first OS and i want to dual boot Fedora12.Ok i installed Fedora12 and choose not to install the bootloader(gonna use the one Debian installed)What i'm tring to do in Debain is edit my /boot/grub/menu.lst
Here is what i have
Code:
title Debian GNU/Linux, kernel 2.6.26-1-686
root (hd0,0)
kernel /boot/vmlinuz-2.6.26-1-686 root=/dev/hda1 ro quiet
initrd /boot/initrd.img-2.6.26-1-686
code....
I installed 11.04 after Windows 7. when the GRUB boot menu starts up there is an option for Win 7 boot but it will not boot windows. When that option is selected the screen changes colour for 2 seconds and then reverts to the GRUB menu. Ubuntu boots fine.I downloaded the Boot Info Script and ran it, the results are
Code:
Boot Info Script 0.55 dated February 15th, 2010
============================= Boot Info Summary: ==============================[code].....
I'd like to install Fedora 14 64bit as a dual boot on an existing win 7 32bit system. When I boot with the Live CD, after selecting "boot" in the Fedora boot selection menu, I get a grey screen with a white cursor, and the system freezes. I checked the Live CD on my laptop and it worked perfectly.
My System:
MotherboardASUS P5Q DELUXE
CPUIntel Core 2 Duo E6750, 2,66 GHz, Sockel 775
[code]...
I installed Ubuntu 11.04 2 days go using wubi. Until today everything worked fine, but now whenever I try to use my keyboard to select the OS option in the boot menu, it doesn't work(arrow keys, enter button nothing works). After 10 seconds the default selection (windows 7) starts up. When windows boots up, the keyboard starts working again.
I googled for the it and found that users who had USB keyboards had this problem, but I'm using a PS/2 keyboard. Also, for 2 days everything went fine but after that it suddenly started happening.
i have insatlled fedora 9 on a system with xp already installed on it but when i start fedora it hangs while booting. after starting the service ANACORN it hangs and same happens with fedora 10. it hangs while starting CUPS.
View 2 Replies View RelatedI just bought a new laptop with the Intel I3 processer in it and it came with Windows 7 preloaded. I am running Ubuntu 9.10 32 bit on my old system but decided to use this opportunity to upgrade to a 64 bit OS and Fedora seemed to be a good choice. Anyways, the problem I'm having is that I am trying to run dual-boot with 7 and Fedora. I got it installed and from the grub menu, I can load both OS?s. I can boot 7 just fine but for some reason Fedora will not finish loading. It will start loading, run though several scripts and then the screen goes black like its trying to go to a splash screen but that were it stops. I tried the rescue option on the boot DVD and it pretty much did the same thing.
View 3 Replies View RelatedHave just installed 9.10, again, many failed attempts previously.Cannot get to boot up and show menu on dual boot with Vista initially,However when I delete the grubenv file the system boots ok and works fine.But does not show the grub menu to choose boot up choices.Got the information to delete the file on some posts elsewhere about booting problem, and tried a longshot and got into Ubuntu for the first time from trying to install now for 3 months!The problem is the file grubenv is created each time so on subsequent boot ups the sytem fails to boot again.The Grub version is 1.97 beta 4, most up to date for Karmic I think, I have seen a version 1.98 but dont think its for Karmic?
Is there a way to modify the grub.cfg file to stop this problem ( all posts say dont touch this file??Or install a script to delete the grubenv file on shutdown as a workaround for me, (I have no idea how to do this whatsoever, I'm not familiar with linux at all)I did read that this problem was fixed/patched in Grub version 2, but dosn't seem.so on my system afetr I updated it when I got into Ubuntu.I couldnt find the patch or fix, I got the information I am on about from this post:URL...It seems to say it was fixed or patched by Colin Watson reading through, but I don't really understand whats being said or how to get the patch on my system if indeed there is one?Sorry for being a bit thick about all this, its a bit beyond my brain now, hope somebody can help out as I have enjoyed my brief bit of fun in Ubuntu.
After quite a bit of troubleshooting, I have only made my problems dual booting XP and Xubuntu go from bad to worse.
I installed xubuntu on my Windows XP laptop as a dual boot system. (Single 40gb Hard Disk, used xubuntu wizard to repartition XP)
After installation, Windows XP would not boot from the boot menu; it would just go to a blank screen with a blinking cursor in the upper left corner (xubuntu was fine).
So far, I have repair installed (not clean) Windows XP and used the Windows XP recovery console commands "fixboot" and "fixmbr" (fixmbr caused xubuntu to become unbootable with no boot menu) to no avail.
I did a fresh install of Fedora Core 10 32bit on my Caompaq Presario AMD 64 laptop which originally only had Vista ultimate 64bit. When I go in to grub and choose windows I get a screen that says:
Windows failed to start...
File: windowssystem32winload.exe
Status: 0xc0000225
Info: The selected entry could not be loaded because the application is missing or corrupt.
I am trying to install ubuntu 10.04 on windows7.windows 7 was already installed.I ollowed these steps to install ubuntu 10.04.1)First i made some freespace in hard disk to install ubuntu using windows7 default options(By shrinking).2)I used USB drive to install ubuntu.I made it bootable using unetbootin.3)I followed normal steps install(language,area,keyboard,using manual partition i installed ubuntu in free space,etc).4)I got boot menu when it restarted.PROBLEM isAs long i use only ubuntu (boot into ubuntu --shutdown--boot into ubuntu --shutdown) it works well.
If once i boot into windows 7 and restart the system i am loosing boot menu options.The following error i am getting"no module name found Aborted.Press any key to exit".If i press any key,I guess its trying boot using internet and lastly it says Operating system not found and hangs.
I've finished the installation of Debian Squeeze using Installer loader from Windows. But the Installer menu is still appear on Windows Boot Manager.
I've try to uninstall the "Installer Loader" from Windows and I got an error message about BCDEDIT (if I'm not wrong), during uninstallation process.
I ignore it, and continue the uninstallation process until complete. But, After I reboot my computer, the Installer menu is still appear on Windows Boot Manager.
I'm using Windows Vista Business SP2.
My system (ubuntu studio 9.10, 32bit) was working just great. Then I installed dropbox via synaptic -- and it worked just great.Then I got some very strange behavior in how my tabs (firefox) worked, and the windows on the system would no longer respond.I restarted.... and the behavior got worse.. my menu would not show up, and when I opened dropbox -- the windows would not move, their menu(s) did not work, and I could not close them.
I tried to:
-- reinstall gnome
-- reinstall nautilus
[code]....
I've just installed Ubuntu 10.10 Netbook edition on a brand new Packard Bell Dot S2 netbook, and when the system rebooted after installation the netbook booted straight into Windows 7.
When I rebooted again and paid more attention to the boot process, there was no GRUB menu (like the one I get when booting up my desktop).
The Windows partition has been resized, but I can't seem to get to the new Ubuntu partition.
I installed Xubuntu 9.10 with Wubi and it worked fine until a recent kernel update broke my install. I uninstalled through Windows and reinstalled Xubuntu 9.10 with Wubi with no apparent problems.When I look in C:ubuntudisks, root.disk, swap.disk, and the boot folder are both present. The C:ubuntudisksootgrub folder is empty; I don't know whether or not it should be that way.But when my computer starts, it just boots Windows Vista without displaying the menu asking me to select my OS.
View 3 Replies View Relatedi just installed ubuntu 9.10 netbook remix, i made a partition (sda6) for it, first i had only opensuse, and when i was installing ubuntu, i put the bootloader in (sda6) the Opensuse bootloader is installed on MBR,
[code]...
When I attempted to install 10.04 on my Toshiba A505-S6005 all appeared to go smoothly, but when the system rebooted the splash screen appeared only after a few seconds of a blinking cursor. The default desktop background appeared, and I heard the drumbeats that announce "Hello!" but there was no login menu.
Background: I have struggled to put linux on this laptop, but there have been many compatibility issues thus far. However, once I switched my hard drive controller to AHCI I was able to boot 10.04 live with no trouble.
On a regular boot I can login via Alt+Ctrl+F1, but even after I run "sudo apt-get upgrade" etc. the login fails to appear.
Furthermore, while poking around in Cli I noticed that my home folder more closely resembled the live environment (i.e, there was an examples.desktop file instead of the usual folders)
I have burned a new CD at a slower rate with a new iso, but this one yielded the same results as the first. Please help, I am currently using Win7, but I would much like to be back on Linux.
I have rebuilt my laptop to a dual boot of Ubuntu 10.10 and Windows 7 - if only iTunes would work under wine I wouldn't even have to worry about Windows, but that is the penalty for using an Apple iPod!
Anyway how do I go about about editing the boot options menu? Following the kernel upgrade in the Ubuntu updates I now have two entries for Ubuntu and would like to just tidy it up.
If it is risky let me know because I have the systems working just nice, and really wouldn't want to trash them just for something cosmetic.
My system had Windows Vista initially. I installed Ubuntu 10.04 64 bit initially and everything was fine. I was able to use both the OS. Recently I installed Ubuntu 10.10 32 bit in the same partition as Ubuntu 10.04 by dividing it into two equal halves. Now I am able to boot into 32 bit 10.10 but when I try to boot into the old 64 bit 10.04 it says unable to mount /root/proc, and some other "Unable to mount.." messages and it gives me a command prompt. I entered into 32 bit 10.10 OS and did update-grub2 and when I restart, the boot menu has no option for 64 bit 10.04 version at all... How can I restore my Ubuntu 64 bit 10.04 and boot into it..
View 9 Replies View RelatedI recently installed Ubuntu 10.10 with Wubi, however after an update was performed on Ubuntu, Ubuntu's boot options appear twice upon starting up the computer. I get the following selections:
View 8 Replies View RelatedI just installed ubuntu 11.04 via wubi. the installation appears to have gone well but ubuntu doesnt appear as an OS choice when i boot up.
Its not a timeout issue as it is set to 30sec and i can see my other options (windows and a recovery option). the only thing i can think of is that my computer has a separate partition set up for recovery and i think that is screwing things up.
Here is my boot.ini:
My only guess is that since the recovery partition is the first partition that its causing problems.
I've installed 11.04 on my laptop (dual boot with Win7). It goes through the grub boot menu and boots in ubuntu but displays ~inch wide band near the top, nothing else. I assume it is a display issue (it has an ATI mobile Radeon HD 3870 X2 card) but can't seem to resolve problem. I can boot into Windows via the menu. In the grub menu I can boot into the command line (grub>) but can't seem to make progress beyond that. Within this grub interface, it won't take terminal commands.
View 2 Replies View RelatedInstalled Ubuntu on a 40 GB partition side by side with Windows 7 currently installed. I have had this exact setup before. Problem, boot menu never shows. The system boots into Ubuntu automatically. Windows seems to be intact and accessible. How can I get the boot menu to appear at startup?
View 9 Replies View Related