Fedora Hardware :: Dual Monitors With Open Radeon And F15?
May 31, 2011
The default install of F15 is not detecting my multiple monitor setup properly.I have two dell 17" monitors running on an ATI hd4650. In system settings the display tool does not detect the second monitor. The monitor is working and on but just shows a mirror of the main display.I didn't see an xorg.conf anywhere to try to fiddle with that... so I don't know what to do. Hitting the Detect Displays button does nothing but cause the 2nd display to flicker for a minute.
View 1 Replies
ADVERTISEMENT
Jul 20, 2011
I am using Fedora 15 with dual monitors. I want to make an application open automatically on the second monitor. In particular I would like to make Firefox open on the second monitor. For now I am just manually moving Firefox to the second monitor, but if I close it down and open it again, it automatically opens on the first monitor. Is there a way to make it automatically open on the second monitor?
I have two Nvidia cards in my machine. I did have one monitor connected to each video card, but I was unable to get a dual monitor set up to work like this, so I plugged both monitors into one card and the dual monitor set up works fine like. Is there a way to make dual monitors work if you have a monitor connected to each video card? When I had a monitor connected to each video card, I could see the second monitor in the Nvidia settings, but it always disabled it. I could enable it, but it would grey out twin view. After I enabled it, I'll restart the X server, the second monitor would auto disable again.
I'm using Gnome, I don't have the above issue in Xfce4 - it works fine with one monitor connected to each card in Xfce4. However, I want to use Gnome. I've searched, but have not been able to find a solution to either of these issues. I read you can fix the application to launch in a second monitor with wmctrl. I've tried to install it with yum, but I get the message: No package wmctrl available.
View 2 Replies
View Related
Aug 8, 2009
I have dualhead configuration - ATI Radeon 7000 with 2 attached VGA monitors.But by booting is one of them switched off:- without kernel param. - nomodeset (added to GRUB), the monitor is switched off just before X start- with nomodeset - is switchet off by X start.In X: xrandr reports only 1 attached monitor (second port is reported as "disconnected") - the same info is in /var/log/Xorg.0.log.I have also try to use my elsewhere working predefined configuration in xorg.conf, but also without effect. The second monitor stays off :On every other OS I have ever tried: Ubuntu 8.04/8.10/9.04, Mandriva 2008/2009.1, Knoppix, SuSE 10.3/11.1, Windows XP, ....I had not this problem.Also - what is wrong in Fedora ? Why do switch the monitor off ? Why reports, that the monitor is disconnected - when it is not true ?
View 9 Replies
View Related
Feb 26, 2010
i have just installed fedora 11. i have two monitors. how to set up dual monitors in fedora 11 ? i tried a lot to search for a way out, however no joy.
View 2 Replies
View Related
Nov 19, 2009
My Dual G5's psu blew up this weekend, and i refuse to go back to windows, so until i can come up with the $$$ for a new PSU i installed Fedora 10 on an old Dell GX270.
Now, ive got 3 video cards to play with. An Nvidia Geforce4MX, an ancient matrox PCI, and the onboard intel VGA out.
Mind you, ALL of these cards work just fine on their own. All of these will work dual and even tripple monitors in XP. But i hate XP.
Now when following th xinerama tutorial, i took bits and peices from the XORG.conf files of each card to make my own..and ALL I GET on boot is "No Screens Found" so i have to remove matrox card (If plugged in) and reconfigure the X server. otherwise if i dont remove the card i get a blank screen.
Now heres the config Fedora gave me for the working NVidia card (singlehead mind you)
Code:
Now heres the one i came up with for the AGP and Matrox PCI Card:
Code:
Whats interesting is, is when i run the grep command to get the PCI id, it only shows the one card. Same when i run system-config-display, it will only detect one card/one monitor. So that leads me to beleive i have to force Fedora SOMEWHERE before it reads Xorg to detect more than one VGA card.
So right now as i type, i'm running the Nvidia, and the Intel...but the intel is just blank. i checked the log file on Xorg, but see NO intel/Matrox anywhere in the file, which makes me wonder if the system is even seeing it.
I do NOT want to go back to windows...and actually when i get my mac back, i think i'll keep this linux machien chugging on the 2nd LCD channels, just because its been so pleasant to deal with.
View 2 Replies
View Related
Jun 13, 2009
I have a dual-monitor setup with a 1920x1200 lcd on the left and a 1280x1024 lcd on the right. In Fedora 11 on GNOME, using display settings, I can configure them properly.
KDE, however, is refusing to let me configure them as separate monitors. They are stuck permanently in mirrored mode, and I can't adjust positioning or anything. Here is a screenshot of the desktop with krandr running.
[URL]
View 9 Replies
View Related
Feb 6, 2010
I am trying to get dual monitors setup but can not seem to get it working, I would like to have it extend the desktop rather than showing the same thing on both screens.
I have a pci video card with a VGA Monitor Y splitter going to 2 monitors.
View 4 Replies
View Related
Feb 8, 2010
Using the Live F12 disc it runs fine, but my dual monitors are backwards, in other words I have to go off screen to the right to get to the left monitor. I couldn't find anywhere to switch them, only identify them, and change res, and such. Before I commit to installing on a HDD I need to get all the kinks worked out first.
View 14 Replies
View Related
Sep 23, 2010
Ever since upgrading from F11 to F13, wallpaper spanning has been driving me nuts. No matter what the size of the wallpaper, I cannot get it to span two desktops correctly anymore. Most styles (zoom, scale, etc...) cause the image to be duplicated on both screens and the "span" style centers the image between the screens and appears to scale down the image leaving large gaps on either side. It's like the background program doesn't recognize the "virtual resolution".
View 8 Replies
View Related
Dec 15, 2010
I'm using F14 with the above video card. I've tried installing proprietary drivers from ati's website but am getting message that suggests that it's not compatible with my kernel version. I've tried using gnome's configuration util which does detect second monitor and configures it. But when I click apply the second screen goes blank even though I'm able to move mouse to and from it.
View 1 Replies
View Related
Nov 19, 2009
Long time reader, first time poster to the forums. I have installed Fedora 12 onto a desktop here. Fresh install and fully updated as of today. In this system there is a radeon 7000 graphics card that Fedora set up dual display for me. This is working fine but unfortunately im seeing a problem with the top and bottom of one of the displays.
Please see the problem here: [URL]... The mouse will go underneath or above the areas i have pointed to. Any ideas what is wrong? In fedora 9, 10, 11 this was all working fine but i did have to use xrandr manually to get dual display working. Edit: Update:
I dd not mention that i kept my home directory. On futher inspection it seems that the issue is because of a .folder in my home directory that was backed up and restored on the fresh install. To check this i added a new user to the system and logged in with a fresh home directory. Does anyone know which folder or file this setting this is stored? I tried logging out, moving .gconf .gconfd .gnome2 .gnome2_private and the .gtk folders to another location then logged in to no avail.
View 1 Replies
View Related
Nov 26, 2009
I used preupgrade to upgrade from F11 to F12. In F11, I used the proprietary nVidia drivers from rpmfusion, and they worked well. I have refrained from installing the nVidia drivers in F12, because of the problems reported for users of KDE. I removed my old xorg.conf, which has references to the nVidia driver and to "TwinView," the proprietary method of managing two screens, so as to let X discover both monitors.
Now, however, my second monitor stays black, even though xrandr and KDE RandR show both monitors correctly. Xorg.0.log shows the nouveau driver is loaded. (I also tried to create a new xorg.conf following guidelines from the web, but many of the guidelines are from before xrandr, and I'm not confident I have it right yet.) It seems that X believes I have two monitors, because I can drag a window off into the blackness (and it's never heard from again!) I know that the hardware is working, because I just booted into Windows 7, and I could see the desktop on both windows.
How do I convince X and KDE to display on both monitors?
View 2 Replies
View Related
May 21, 2010
After working on trying to get my 3 monitors to work with Ubuntu 10.4 and my ATI Radeon HD3200 (IGP) and HD4850 cards, I just had to share the xorg.conf. I am using the default open source drivers that came with 10.4 and I kept KMS enabled (it wouldn't work without it).
Here is my conf:
Code:
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "4850-2-Screen"
Screen 1 "4850-1-Screen" RightOf "4850-2-Screen"
Screen 2 "3200-Screen" RightOf "4850-1-Screen"
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
Option "Xinerama" "on"
#OPtion "Clone" "off"
EndSection .....
View 9 Replies
View Related
Jan 19, 2010
I'm running Ubuntu 9.10 on an HP Desktop with an ATI Radeon 2600 pci card that has four outputs. I want to run the same 3-monitor array that I had in windows. Is it possible to get this thing running and configured right in Linux? At the moment I can only get it to send a signal to 2 monitors. I installed the drivers step by step from the manufacturer, but I can't seem to get a signal to all 3 monitors.
View 6 Replies
View Related
Jul 1, 2011
I want to be able to login on different users on my two screens. Is that possible? It would be nice if I could have the left screen and my gf could have the right. I'm using ubuntu 10.04 with gnome, and I have a Nvidia graphics card.
View 8 Replies
View Related
May 3, 2011
My system config is in my sig.I want to know if I have hardware acceleration using radeon open source driver.I did substantial searching on the internet and have come across this post:ATI Hardware Acceleration - XBMC Community Forum
I am doing all this because I have read on the internet that the open source radeon driver does not enable H/w acceleration properly which means that choppy performance while playing HD movies and / or while playing OpenGL games. Not that OpenGL games don't work, they just work very slowly even with Direct Rendering of Mesa drivers. Then there's this thing about Kernel Mode Setting as well which isn't available in the proprietary ATI driver.
View 7 Replies
View Related
Aug 4, 2010
Can anyone help with me configure my dual-screen monitors for rotation? I have xrandr 1.1. Have tried various approaches, nothing takes. I can't even get the xrandr options to show up in KDE's Display control panel.
My lspci output: 03:00.0 VGA compatible controller: ATI Technologies Inc RV516 [Radeon X1300/X1550 Series] My current xorg.conf (works, minus screen rotation): # Xorg configuration created by system-config-display
Section "ServerLayout"
Identifier "Multihead layout"
Screen 0 "aticonfig-Screen[0]" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
Option "Xinerama" "off"
[Code]...
View 1 Replies
View Related
Jan 12, 2010
How can I install some open source drivers like radeon or radeonh, I just want make my desktop effects work, can't even watch a movie I have these installed:
Code:
#X -version
X.Org X Server 1.7.1
Code:
#rpm -qa | grep -i radeon
radeontool-1.5-6.fc12.i686
[Code]...
View 4 Replies
View Related
Mar 25, 2010
setting up my dual monitors. I can get a continuous screen but the screen does fill the lcd screen all the way. I have dove in to xorg. I'm on fedora 12 .
[Code]...
View 6 Replies
View Related
Apr 3, 2010
So I'm using Lenny, trying to get dual monitors set up. I'm not sure on the correct steps, but have done some googlin' and wasn't finding what i was looking for. (could be that i just missed it)
lspci:
01:00.0 VGA compatible controller: ATI Technologies Inc RV516 [Radeon X1300/X1550 Series]
01:00.1 Display controller: ATI Technologies Inc RV516 [Radeon X1300 Pro] (Secondary)
View 2 Replies
View Related
May 28, 2010
I have a Dell inspiron 1525 laptop with a 1280x800 display and an external 1280x1024 monitor. I'm using 9.04 with openbox. I've done a loooot of online reading about how to get a dual monitor setup using xrandr, and I really don't know what I'm missing here. So here's the deal: I want to have my external monitor on the left of the laptop's display, and of course I want each of them to display different parts of the desktop.
First I set up the right resolution to each one of them (I do it using lxrandr). Typing xrandr -q in a terminal, I get the following:
[Code]...
View 9 Replies
View Related
Apr 21, 2011
I have an asus p5kpl-cm MB. I plugged in a radeon 9200 pci card. In the bios, I can set up:
pci/igd
igd/pci
igd
etc.
This determines which of the 2 displays (pci card or internal graphics on the MB) is the boot display. That determines which comes up with the bios screen and then once booted into ubuntu (10.04), this is the only adapter/monitor seen. The button detect monitors doesn't do anything.
lspci sees both my internal and pci card graphics. So, I can get either to work just fine (auto detected etc.) just not both at the same time.
I've tried all of the 3 above settings, and even when I set it to just igd, lspci still sees both my adapters. It identifies them correctly, and it works perfectly, detecting the monitor and knows the resolutions for each - just not both at the same time.
Does ubuntu know how to automatically configure more than one display w/o doing something else, or must I do something else to get both going together?
Code:
$ lspci
00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 10)
00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express Integrated Graphics Controller (rev 10)
[Code]....
View 6 Replies
View Related
May 20, 2010
I installed the latest nVidia drivers on my laptop using the 9800M card. The laptop is a Gateway P-7805u and I'm connected to the second monitor using VGA.Also, before installing the nVidia drivers (and just using the basic drivers included with Kubuntu 10.04), basic dual monitor support worked, except I could not enable compositing features for some reason. So I thought the proprietary drivers would fix this.Several issues have arisen since installation:
1) I've clicked through all of the display settings to activate the second screen with absolutely no change.
2) When I try to apply settings and Save Configuration as the nVidia help suggests, I am told that I cannot save to the X.conf file. I assume this is due to innate permissions on my user settings, which I have no idea how to properly configure.
3) I have no idea where to go from here, as most of the fixes I found online involve Linux syntax and verbiage, to which I'm totally clueless after spending over half my life with Windows.
View 1 Replies
View Related
Mar 1, 2010
I'm having trouble setting up dual monitors on my HP Pavilion dv7-1020us laptop, with an Nvidia 9600M GT graphics card, and Ubuntu 9.10. I installed Ubuntu via Wubi, on top of Windows 7. I tried this before on the same laptop when I was using Vista and Wubi, and Ubuntu was able to recognize my Graphics card, and install a proprietary driver. I wasn't able to test dual monitors, though. However, now that I'm using W7 and Ubuntu, it cannot use a dual-monitors correctly. It recognizes the monitor, but it only displays a mirror display of my Laptop monitor, not acting as a separate monitor, like I want it to. I tried messing around with the settings in the display menu, but nothing works. I tried downloading linux drivers for my card from Nvidia's site, but the file is in a .run extension, which I don't know how to install. What should I do to get this working?
View 7 Replies
View Related
May 4, 2010
I have a ATI VisionTek 9250 128mb DMS59 PCI video card that I would like to use for dual monitors on Ubuntu 10.04 Gnome. I installed the card and booted the live cd. Both monitors are recognized when I go to the display settings, but when I un-check the mirror box, nothing changes. I am still only getting one monitor. I was previously using 9.10 and it sometimes worked, but not always.
View 5 Replies
View Related
Oct 23, 2010
I just downloaded Ubuntu 10.10 and installed it today. I was just wondering, does Ubuntu support dual monitors? I tried looking through the settings in Ubuntu but I couldnt figure it out.
View 1 Replies
View Related
Nov 1, 2010
I have a brand new installation of Ubuntu 10.10. I'm using a GeForce 8600GT graphics chipset. I have two monitors, and my goal here is to have them both working under Ubuntu in their full resolutions, and I've not had any luck with this yet. I've got a Viewsonic VE155s with a native resolution of 1024x768, and a Chimei CMV 221D with a native resolution of 1680x1050. When I first installed Ubuntu, both monitors were working, and the VE155s was working in its native resolution of 1024x768, but the CMV221D was stuck in 640x480.
The Nvidia video configuration utility was not identifying the latter monitor - it only reported it as DFP-0, and doesn't allow any resolution above 640x480 to be set. The mechanism (which has a name which I don't recall) which allows the OS to interrogate the monitor's firmware to find out the monitor manufacturer, model and accepted resolutions and frequencies to use does not seem to have worked. (I previously had the Nvidia driver installed, but I've since switched back to the default open source vesa driver. I won't use the closed Nvidia driver if I don't need to, but if I need to use it to get acceptable performance from this hardware than I will.)
So I did a little bit of reading and I did some hacking of xorg.conf. Previously I had the 15" monitor working in 1024x768 and the 22"
monitor working in 640x480. Now I've got the 22" monitor working in 1680x1050 as desired, and the 15" monitor not working at all. Here's a copy of my xorg.conf. For the sake of brevity I have not included the unnecessary bits such as input devices.
Code:
Section "Device"
Identifier "NVidia"
#Driver "nvidia"
[code]...
View 1 Replies
View Related
Jan 24, 2011
I'm trying to set up my monitor and tv for dual display but I'm having some problems. I want them to display the same thing so I've enabled twinview and I figured the second display position should be set as clone but when I save xorg and restart the x server the position reverts to absolute. Anyway, the monitor is set as the primary display and it's the one I'm having problems with. The tv is fine but the monitor's display is stretched off the screen so I can't see the far right or bottom of the screen. I'm very new to linux and I'm just finding my feet so if there's any other info needed you'll probably have to be very specific.
View 2 Replies
View Related
Mar 23, 2011
The problem is that I don't have NVIDIA graphics card These are my HP ProBook 4510s Laptop's specification: [URL] And I think my built-in graphics card is Mobile Intel� 4500MHD Did anyone Dual Monitor with this Laptop or knows how to Dual Monitor with it?
View 3 Replies
View Related
Nov 1, 2010
I'm trying to get dual monitor support enabled in Suse 11.3 Previously I had this in Suse 11.2 using a dedicated NVIDIA graphics card with VGA and DVI output and this was done in a GUI. I now have 11.3 and a built in ATI card with VGA and DVI output When I run xrandr I get the following Code: Screen 0: minimum 320 x 200, current 1440 x 900, maximum 8192 x 8192 VGA-0 connected 1440x900+0+0 (normal left inverted right x axis y axis) 408mm x 255mm
1440x900 59.9*+ 75.0
1280x1024 75.0 60.0
1280x960 60.0
1152x864 75.0
[code]....
I tried using xrandr --screen 1 but it says Code: Invalid screen number 1 (display has 1) I'm looking to expand the desktop onto the second screen so I can photo edit on one screen and web browse and instant message in the other screen Currently using the Radeon R600 classic driver from ATI
View 5 Replies
View Related
