I am going to install Fedora 14 on my home PC but I need to connect it to a wireless network.USB based wireless network interface that is supported by Fedora 14?I am looking for a USB based wireless network interface that does work after setup without the need of any particular configuration or of any unsupported software component..
View 4 RepliesI am having a little trouble connecting to my wireless network. Running Fedora 10 32 bit.I'm trying to connect to a hidden wireless network. I updated the firmware for my driver but apparantly the driver is still not working. Broadcom has a driver from their website for Linux 32 bit systems. Should I attempt to install it? I read a post where the driver is built into the system kernel. If so I would need to blacklist the one of the drivers. Correct?
[justin@justin ~]$ iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
wmaster0 Interface doesn't support scanning.
code....
When i click the button to connect to a wireless network this message apears:Network management disabled
View 1 Replies View RelatedI picked up a cheap PC the other day for �20 and it came with a Belkin N Wireless USB adapter. I know the adapter works because Windows XP was originally installed and I could connect with no problems. I wasn't able to connect when I installed Kubuntu so I thought I'd see if I could have any more luck with Fedora....so far, not so good! I realise that this is a fairly common problem, especially for this USB adapter, but I've tried dozens of threads here and elsewhere and still can't get Fedora online.I can see the wireless networks in the list, but if I try and connect then I just repeatedly get asked to enter the authentication details, which I know I'm providing correctly.
View 9 Replies View RelatedI have upgraded to Fedora 15 but cannot get wireless up and running. When i switch on wireless and choose the connection it tries for 15 seconds before prompting me for the password and continues like this. When i check the device in my network config it shows as being inactive. Ralink device 3060
View 6 Replies View RelatedI'm running the 64-bit version of Fedora 12 on a MacBookPro5,1 system. I am unable to connect to my wireless network, which shows up in the list of available wireless networks.
I will enter my password and the system will try for several seconds to establish a connection and then fail.
I know the network is fine because I can connect to it when I boot the computer in Mac OS X.
What can I try that will allow me to connect to my wireless network under Linux?
How to make my fedora 8 be able to connect to the internet by using wireless network ?
View 5 Replies View RelatedF14 did not recognize my wired or wireless NIC upon installation. I have enabled network manager, what should I do from here? Here is my hardware specifications:
Network controller: Realtek Semiconductor Co., Ltd. Device 8176 (rev 01)
Ethernet controller: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller (rev 05)
I am trying to get a wireless connection on my laptop. The OS is fedora minimal (without GUI, Without gnome). So I need to be connected on my Access Point, which has an hidden SSID on WPA2-Enterprise.
View 2 Replies View RelatedI'm running the 64-bit version of Fedora 12 on a MacBookPro5,1 system.
I am unable to connect to my wireless network, which shows up in the list of available wireless networks.
I will enter my password and the system will try for several seconds to establish a connection and then fail.
I know the network is fine because I can connect to it when I boot the computer in Mac OS X.
What can I try that will allow me to connect to my wireless network under Linux?
I am fairly familiar with Linux but had never ventured into Wlan settings / options / too much. I have compatible card (aetheros) and when running - iwlist wlan0 scanning - I get plenty networks showing up - meaning the card works. When I installed distro which is last night (before I ran update), I had that little bars menu at the top of the screen that showed available networks once clicked upon. Since I like to modify and make my settings better - I removed that little AT&T like bar, and now rebooted after update to find that I can not see available networks unless I use iwliset wlan0 scanning.... .#$*&)@&#(&%# - need I say more.
Two questions - how do you connect to the wireless network via command line? What is that vertical bars GUI tool called so I can find it and run it again? Is there (for the love of god) alternative to system-config-network GUI managment tool for wlan?
I'm tryn' to connect to my wireless network using command line:iwconfig wlan0 essid MY_NETWORK as root.
After this typingiwconfig wlan0
result is:
wlan0 IEEE 802.11g ESSID:off/any
Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated
Bit Rate:1 Mb/s
[Code]....
I installed ndiswrapper in order to use ipn2200 WinXp drivers.
running Fedora 15 on a Dell Inspiron 1521. When I first installed Fedora on this laptop, I was unable to connect to a wireless network because I did not have the firmware installed, so being a good little enthusiastic new user of Fedora, I set out on a quest to locate the proper firmware. I had success on that front, however, in the process of installing it, the option to connect to any wireless network disappeared. It isn't that there is no wireless network in range, rather, the entire wireless option itself has vanished.
View 3 Replies View RelatedThis will allow you to use iphones' data plan as a wireless access point. Currently setup instructions are only posted for windows/mac using a helper app to configure the laptop. Here are the instructions I followed to setup iphonemodem2 to work under Fedora 10: Download iPhoneModem2 from a jailbroken iphone using Cydia. Create a new wireless network on Fedora with the following settings:
a) SSID = "iPhoneModem"
b) Mode = Ad-hoc
c) IPv4 Method = Automatic (DHCP)
Connect laptop and iphone to new wireless network. Start iphonemodem app on iphone. The "traffic" does not update; the "status" says "Wrong Wifi Network"; and the signal strength says 0%. However, the network connection should be there as long as you have a data signal to your service provider.
I installed the 64-bit version of Fedora 12 on my MacBookPro5,1, and I am unable to establish a connection to my wireless network, which I can connect to fine with I boot the computer into Mac OS X. Here is my operating system information:
Code:
$ uname -a
Linux tosh 2.6.31.12-174.2.3.fc12.x86_64 #1 SMP Mon Jan 18 19:52:07 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux
Here is information about the PCI devices available on the system:
Code:
$ lspci
00:00.0 Host bridge: nVidia Corporation MCP79 Host Bridge (rev b1)
00:00.1 RAM memory: nVidia Corporation MCP79 Memory Controller (rev b1)
00:03.0 ISA bridge: nVidia Corporation MCP79 LPC Bridge (rev b3)
[code].....
I have just installed FC12 on my machine - and gone Windows free for the first time ever. Now I do use various flavours of Linux on a daily basis but not from an installation/sys admin point of view so my questions here may seem a little basic but pleas eindulge me if you will!
Now, my network connection works perfectly well under the following scenarios.
1) FC12, wired to router
2) FC12, wireless, SSID broadcast enabled
3) Ubuntu (laptop), wireless, SSID broadcast DISABLED
The only scenario that does not work is FC12, wireless with SSID broadcast disabled.
I can only assume that it is an issue with my USB modem (a linksys WUSB54GS) since the same set-up works fine from my laptop running Ubuntu with an internal wireless card.
Now, I know from reading the forums that it's pretty easy to get around a disabled SSID broadcast but this is an itch I just have to scratch....what the hell is causing this problem?
nm-tool ouput is as follows:
I have tried using wpa_supplicant but I am not sure which driver I am using here - is it ndiswrapper per chance?
(Driver: rndis_wlan)
How I can connect once again to my wireless router with SSID broadcast turned off.
at start, knetworkmanager detect wireless network, but doesn't automatically connect - I have to restart it to make it work properly. Instead, it gives that error:
[Code]...
On Opensuse 11.2, I would like to connect my ipod touch to a wireless ad-hoc network of my laptop. I have no wireless WIFI-router at home, so I have to use the laptop as a router to the internet. I know I have to enter a static IP adres and my router's address, but where ? I haven't found any place under network tools to do this, only saw some fields with SSID's and MAC addresses to fill in.
View 5 Replies View RelatedI've got openSUSE 11.3 running via liveUSB on a netbook and no matter how many times I try, I cannot get wireless to connect to my network.
My network is:
- non-broadcast
- WPA2 Personal
- G
The netbook is fairly recent from Asus and wireless works perfectly with Fedora 11 and Windows XP.
The problem with my wireless network. I have Dell DV6 Pavilion 2115 eg laptop and i installed Ubuntu 11.4 and internet and wireless worked, until i reboted my system it has disapear. I cant no longer to connect to a wireless network. It dont shows me any wireless network. My wireless card is Atheros AR 9285 802.11b/g/n Wifi Adapter
View 9 Replies View RelatedI clicked "Network Settings", and I found that the ip address was wrong, which is "192.168.1.10/24", and netmask field is empty, so I modifed the configuration file located in /etc/sysconfig/network, named ifcfg-wlan0, added one line(NETMASK= '255.255.255.0'), saved it and reboot the system. After rebooting the system, I still found the ip address is wrong and netmask field is empty, so I have to use ifup command to activate my card manually every time the system starts.
View 1 Replies View RelatedI'm moving from other distros. and I'm currently loving openSUSE and I'm probably going to stick with it for a long time.I have already googled for this, but I found no solution, but I figured this should be a common problem... Does google searches inside this forum?Now... for my problem, whenever I hibernate (suspend to disk) or sleep (suspend to ram) I can't resume my wireless connection nor connect to another.I don't know if this is an issue if I use cables, because I simply don't with my netbook:The hardware in question is an ASUS 1005HA eee pc, running openSUSE version is 11.3 fully updated. Didn't mess with wireless connections, nor kernel or hibernate settings
View 9 Replies View RelatedAfter installing 11.4, I need to type in the command to update the firmware for a broadcom wifi adapter. Then I needed to reboot, twice, before the system knew to use the adapter (where the adapter wifi light goes from orange to blue).
Then I needed to add my wireless network and type in my key. But the key does not take. If I click on my wireless network icon, it just re-asks for the key and does not connect nor give any other message. Network icon continues to display no connection.
So I need to reboot again.
When the system starts again, the adapter is blue, I click on the icon for my wifi network and it connects without asking for my key and I can then set to start my wifi by default.
Now my wifi works fine.
All settings are correct as far as i can tell. The wep key works on all my windows boxes. When i have connect automatically enabled it never tries to connect. if I go to edit it it pops kde wallet up i put in credentials. wallet goes away then nothing happens. if i double click connection to my router also nothing happens. I have the wep key in there and i even made it visible to make sure.
View 5 Replies View RelatedI am using OpenSuse 11.3 and Network Manager is giving me a headache by not connecting to WEP based wi-fi network.It works in a wi-fi at my office while at my home, it shows / detects the network but keeps asking me over and over.
View 3 Replies View RelatedOne of the biggest issues i have at the moment is that my network based plasmoids on my KDE desktop load before my wireless network connection is established, so i'm thinking it would be best to start up the wireless connection at boot time. On previous distro's, I did this with netcfg but I can't seem to figure out how to do so in OpenSUSE 11.2. Is this the best way to manage this issue or is it possible to set a delay before the plasmoids load up?
View 5 Replies View RelatedI just installed opensuse 11.4 and i'm not being able to connect to my wireless lan. It recognizes my network, but when I click "ok" after typing the password it is like I had done nothing, no connection is set at all.I guess it is probably some configuration stuff since my notebook recognizes all available wireless networks. Sorry about the lack of details, but that is all I got.
View 6 Replies View Relatedi've installed openSuse 11.2 on my laptop (dell studio 15).Today at work i tried to connect to the wireless network, but i couldn't. First, the network card wasn't being recognized, but after a long time trying i was able to set it up, for this i used this command:
Code:
zypper in broadcom-wl broadcom-wl-kmp-desktop
So now, the networkmanager detects all the networks around, but i cannot (or i don't know
[code]...
I just switched from Ubuntu to Fedora 13 because I was unable to get Ubuntu to connect to wireless networks. I tried everything suggested in help and forums, and kept getting "Bad Password" with WICD and Network Manager. Now, with Fedora...I still can't connect.
Problem #1: The guide says to "...make sure that the relevant wireless interface (usually eth0 or eth1) is controlled by NetworkManager," and that I do this via: System>Administration>Network
However, there is no Network option under System>Administration.
Problem #2: I open Network Manager, which displays a list of networks. I click on mine, configure it with WPA and the right password, and it fails to connect: "The network connection has been disconnected."
Kernel: 2.6.27.15-170.2.24.fc10.i686
WLAN: Broadcom BCM4311
Problem: I run WPA2 Personal encryption on all my wireless devices. At work we use Cisco WAPs and I can connect flawlessly, simply by entering the password. At home I use Apple's Timemachine, which is basically an Airport Extreme A/B/G/N router.
I go to Network Manager and choose "Connect to Hidden Wireless Network". I enter in the SSID of my home wireless, choose WPA2 Personal, and enter in the password. After ~1 minute Network Manager spits back a window requesting the WEP key.... But I'm not running WEP. This is extremely frustrating. I delete the network and try again... same behaviour. My assumption is that this may be isolated to Airport Extreme network devices but I'd really love to find a fix. Just FYI: I have a MacBook Pro and a system running Vista that connect without a hitch.