I'm running Fedora 10 OS ( I need this older version for development reasons).
I have two newtork cards,
one on a 10.51.54.blah domian
and one on a 192.168.200.blah domain.
I need to set up another network connection to be on a 10.10.10.blah domain as I have to access a piece of hardware that has an address 10.10.10.10.
So I need to have all three address ranges available on my PC at all times
How do I do this??
Version 10.04 LTS. Installed desktop version and network worked but I needed a static IP address and the install configures for a DHCP configured address. I tried changing to static address using the System->Preferences->Network Connections application but was unable to get the system to come up with the network up.
So I manually modified the /etc/network/interfaces and the /etc/resolv.conf files. I restart the system but when I do an ifconfig, I don't see a configured IP address on eth0 (only the loopback address). If I run /sbin/ifup eth0 everything then works fine and ifconfig shows the correct address bound to eth0.
My files are as follows:
To add a new IP address for the network card in the fedora, the only thing I have to do is to copy the file ifcfg-eth0 which is under /etc/sysconfig/network-scripts/ to a new filename called ifcfg-eth0:1 and change the IP address and the DEVICE?
OK, what about other files as following code...
They will be changed automatically if i changed the file under the network-scripts or i have to change them manual?
Am I miss any thing else need to be done?
When I install the FC11 by using"Install or upgrade an existing system"or"Install system with basic video driver"mode...Point 1, I can't config the network config ( IP Address ), due to theerror of network manager...Point 2, I can't enter into the text mode to do the installation steps.Remark:The machine is provide Web,DNS, and Mail Server on the NET ( Internet )
View 1 Replies View RelatedI have a HP Officejet 6310 as a network printer
How do I find the network address of the printer so I can install it?
I have installed Fedora 10 on my A860 Dell Vostrol Laptop with AR242X Atheros Wireless card. Wireless card worked out of the box and i could detect wireless network and connect to it. But i have a problem that, my wireless connection is not able to get IP address from the DHCP server. Please help me out what can i do to get this working. I am using WEP security and authentication is open system.
I have windows 7 beta installed on the same machine and on that wireless network works fine so i am sure that there is no problem with the wirless network. I am using DIR-300 router from D-LINK. I tried to see packet log on wireshark and there i see that there is no reply to the DHCP discover message. Actually i don't see any RX packets at all. Which is not normal as there is traffic on the network.
Someone just erased my HWADDR line from /etc/sysconfig/network-scripts/ifcfg-eth0. How can I obtain my original MAC address?
Code:
ifconfig eth0 does not work (it shows the wrong MAC address) since the HWADDR line from the file I mentioned above was erased. Also there is no ifcfg-eth0.bak backup configuration file.
I'm using a D-Link Xtreme N PCI express wireless adapter (DWA-556). It shows up in the network manager.
However it does not get an ip address from the DHCP server. Below is what I get in the messages log:
How do I activate static DNS for mobile broadband. I can't find any place to write down this information. Settings are made in Network Manager - not Yast.
View 3 Replies View RelatedI am facing two issues with CUPS - 1. I have installed cups 1.3.9 over OpenSuse11 x86. Please check below -
cups:/usr/share/cups/banners # cups-config --version
1.3.9
cups:/usr/share/cups/banners # cat /proc/version
Linux version 2.6.27.7-9-pae (geeko@buildhost) (gcc version 4.3.2 [gcc-4_3-branch revision 141291] (SUSE Linux) ) #1 SMP 2008-12-04 18:10:04 +0100
I have added few printers over there and everything is working fine. I can also able to add - delete - modify any printers from "yast2 printer" command. I can also able to browse cups web interface via http://cups:631, but when I am going to manage the printers (start - stop - delete etc), none of the buttons are working in firefox5 not even in IE also. Older version of firefox is giving error as "This address uses a network port which is normally used for purposes other than Web browsing. Firefox has canceled the request for your protection." All other buttons are working properly.
2. LINUX - LINUX Printing - OK
LINUX - WINDOWS Printing - OK
WINDOWS - LINUX Printing - NOT OK
While giving printing from Windows machine (Printer attached on Linux), there is no problem to coonect the printers, but unable to print.
When I attempt to connect to a wireless network, the network manager asks me for the network's password, then says 'setting network address' for 20 or so seconds, then asks me for some random Hex or ASCII key in the same type of window I put the password in (Secrets for Noel -- KDE Daemon). Since a key is already typed into the window, I press OK, which then causes the network manager to go back to 'setting network address', then the window pops up again and keeps repeating itself.
I'm running Opensuse 11.4 with KDE, and my driver is ath9k. I don't know much about linux so please don't tell me to 'recompile this' or 'change this setting' without explaining how to do it. Please help, I've been unable to connect to wireless in OpenSUSE for 2 weeks now.
I've updated a desktop from 11.1 to 11.2 with the NET CD. After completion everything worked fine, though I have some issues with the NIC. been looking on the net and the provided solutions haven't been able to resolve the matter. After reboot I don't get an IP address, I go into Yast2 and network settings displays:
I have to delete the unknown device everytime after a reboot in order to get a new IP address. After that all works as it is suppsed to. I've been looking into the /etc/udev/rules.d/70-persistent-net.rules and deleted all that was in there,
I use getaddrinfo to get the ip address of the server, it works well on other 3 machines, but always get local address 127.0.0.1 on an 64 bit linux machine. Therefore, other remote clients can not connect to the socket server because the server binds local address l27.0.0.1.
I have also tried pass 0.0.0.0 to getaddrinfo, now the server bind on 0.0.0.0(all available interface). But now I can not print the correct network address of the server, as it is always 0.0.0.0 which is provided by getsockname.
I do not know how to get the network address of the server, rather than the local address.
How to set IPs address on my server using Linux Suse 10.0. Its an old system which was configured before, the type of the modem was changed were by i need also to change the some IPs on the server.
View 2 Replies View RelatedI installed 11.2 on VMware 6.03. My os is windows 7.When I try to go online a pop up showed up
View 1 Replies View RelatedI had 200 workstation with both Windows XP and SuSe Enterprise Linux. Sometime, a few clients can't get IP address from DHCP with SuSe OS. With the same computer, if I reboot and chose Windows XP, it work fine. The log message or the boot message was "No IP Address yet ...backgrounding". I tried to reconfig network device, restart services, change another port, change another line LAN, set static IP Address .... but there's no luck for me.
View 5 Replies View RelatedI want to know how I can investigate...
Q1- what IP address somebody has in the same network?
Q2-Is there any command I can use to figure that out?
I am coming across a strange error with my gateway. When I do a "ping", this is what I get below:
k-63a5b848c6cb4:~ # ping simba
PING simba.gateway.2wire.net (192.168.1.69) 56(84) bytes of data.
64 bytes from k-63a5b848c6cb4 (192.168.1.69): icmp_seq=1 ttl=64 time=0.041 ms
64 bytes from k-63a5b848c6cb4 (192.168.1.69): icmp_seq=2 ttl=64 time=0.029 ms
64 bytes from k-63a5b848c6cb4 (192.168.1.69): icmp_seq=3 ttl=64 time=0.023 ms
64 bytes from k-63a5b848c6cb4 (192.168.1.69): icmp_seq=4 ttl=64 time=0.015 ms
Is the gateway doing something strange?
I've just installed opensuse 11.2 with the network installation iso. During the installation, it has got the IP via DHCP without any problem, and I has downloaded all the needed packets without problems... But when the installation finish.I have no network connection It's strange, because I have IP address, I get the IP from the DHCP server, and I can see the IP addreess if I do "ifconfig", the default route and even the DNS servers in the resolv.conf file; but I cannot ping my gateway (that is the DHCP server as well!!), I cannot ping anything in my network and either anything in internet. I see a network error at the start, but it finally gets the ip address. In the dmesg, the last message repeats over and over. The machine is a Hyper-V virtual machine, but as I said... I worked very well during the installation, I don't know what is going on. I've tried to reinstall, but it doesn't make any difference
View 2 Replies View RelatedI would like to build a centralized address book for my SOHO server. Is that possible without the use of openLDAP (I would like to avoid that)?My clients will be:Thunderbird, KMail (for KDE 3.5) and webmail.If so, do you have any suggestions/Howtos?
View 4 Replies View RelatedI want to set my desktop IP address to always be 192.168.1.2. The NetworkManager connects to the network automatically and the IP address is assigned randomly. I can set up another connection in NetworkManager and always change over. But is there any way to make the default eth0 interface to be permanently set to a certain address (using NetworkManager, not ifup)?
View 9 Replies View RelatedI have a server with 2 network cards. eth0 is used for all traffic and everything is working fine on this side. Eth1 is used for traffic to and from 1 ip address.
Lets say the ip address of eth1 is 123.123.123.10 and its gateway is 123.123.123.1. I need to pass all traffic to 123.123.123.20 through eth1. What command would i use?
I am running 2.6.27.21:170.256.fc10.i686 on my laptop.
I am trying to connect to a network at a university in China right now and I cannot figure out how to connect.
IP: 192.168.213.179
subnet mask: 255.255.255.0
default gateway: 192.168.213.1
DNS: 202.202.96.33
DNS: 61.128.128.74
i have a big problem y have to make an alias for the eth0 interface, i made it with yast and my alias was eth0:1, first, if i try to shutdown the interface i cant it give an error and tell me that the interface dont exist and the second threat is if i can put a default gateway for this alias something like this in other distributions:
route add 128.26.6.11 gw 192.168.28.201 dev eth0:1
I just set up a new router for our home office. I've enabled traffic logging, and I'd like to have the logs emailed to me. However, in order to configure email-notification, the router needs and outgoing mail server. Forgive me, but I don't really understand the terminology being used here. I've googled this a bit, but I'm not sure I now what "outgoing" vs "incoming" mean in the context. I tried using my gmail account as the outgoing mail server (smpt.gmail.com) but it requires TTLS encryption, and there's no option for that on my router.
So I figured I'd setup a simple mail server on my local network. I have a dedicated server machine, so I'd just configure a mail server there. But I got stumped at the first input box (in the yast module):"Outgoing Mail Server".That's what I wanted to use this server for. What is this "outgoing mail server"? I understand it in a normal emai context (I think) but this is confusing me. I've read through the HowTo on the openSUSE wiki, but it still doesn't answer this question.Isn't there some way to have a simple, local mail server (without MX records and the like) so I can send email from a local machine?
how I can define a local static IP address (so that I can run a web server off of the same IP, rather than letting my router DHCP it)?I've tried doing the YaST->Network Devices->Network Settings->Traditional Method with ifup->Set NIC to desired IP->Set Default Gateway to router address method, and afterwards I can't even get into my router anymore (not even responding to ping).
View 8 Replies View RelatedI have a couple of openSUSE 11.2 machines and each is directly connected to the Internet (they are not behind a router, firewall, etc). I want them to be able to communicate without any firewall restrictions, but keep the firewall rules for all other IP addresses. Is this possible? the software package I'm trying to use randomly chooses a port to use in the range of 32768-61000 and I don't feel comfortable having a port range that wide open on both machines.
View 5 Replies View RelatedI have a problem with tightvnc, when I set up a dinamic ip with networkmanager it works fine but if I set up a static address connection it display an error "You have been unexpectedly disconnected from 'hometsa-comp'. Would you like to reconnect?"
"Couldn't convert 'hometsa-comp' to host address" I have setup the ip address, netmask, gateway and dns server in the network manager static address, it works when I setup the vnc connection using ip address instead of hostnames.
I am trying to use a ZTE AC2726 USB EVDO Modem on openSuSE Linux 11.3 Gnome to connect to the internet. I have edited the /etc/wvdial.conf file as follows:
[Dialer Defaults]
Modem = /dev/ttyUSB0
Baud = 57600
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Init3 = .....
When I execute the wvdial command on the terminal the following error appears
joey-suse:~ # wvdial
--> WvDial: Internet dialer version 1.60
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
ATZ
OK .....
The /etc/resolv.conf file has the DNS addresses as below
nameserver 212.49.70.22
nameserver 212.49.70.23
How do I resolve this and connect to the internet?
I believe I have the wireless card installed properly and wicd sees the router. When I try to connect I get an error "can not obtain IP address" Output from iwcongif and lspci is.
dillan@dillan-desktop:~$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
[code]....
