Debian Hardware :: Reboot / Restart Instead Of Shutdown (wheezy)
Oct 16, 2012
Come across with a situation where all methods of shutdown result in a restart/reboot? I've tried commands:
- shutdown
- halt
- poweroff
.. with various parameters, nothing works. The laptop seems to power off, but after a sec it restarts/reboots. I've Googled high and low, but there's very little on this topic. Maybe it is specific to the current kernel in Wheezy? I'm not suspecting a harware failure, since this was not happening with Windows installed.
This happens on me with Wheezy on a HP Elitebook 8530w.
View 14 Replies
ADVERTISEMENT
Sep 3, 2011
i have fresh installed debian wheezy xfce4, and using slim to start it but i can't get reboot, shutdown and thunar can't open flash and others volumes. i using .xinitrc (exec ck-launch-session startxfce4)
View 3 Replies
View Related
Jul 26, 2015
I have upgraded my debian server on april when Jessie came up, but I *forgot* to reboot at this time. As a new kernel* was released this week as a security update, and since my server installed it (via unattended-upgrade on security packages), I rebooted it last night. It never came back online.
I have access to a rescue boot (Ubuntu 12.04 LTS), and tried to analyse the failure (by mounting /sys /dev /proc and /boot and chrooting), but without luck so far.
As it's a dedicated server, I don't have access to the console. What I know :
No log in var/log since the failed reboot. I don't know how to have/find others logs.Previous kernel was 3.2.0-4-amd64, new is 3.16.0-4-amd64, What I tried without luck) :
Change the booting kernel, via update-grub. Tried 3.2, 3.2 with sysvinit and 3.16 rescue mode I think. I should have done it right, but without console it's hard to tell.apt-get update/apt-get upgrade/apt-get dist-upgradeadding nomodeset to kernel load in grubWhat I haven't tried :
update-initramfs, I don't really know why it would block the boot
*linux-image-3.16.0-4-amd64:amd64 3.16.7-ckt11-1+deb8u2
View 6 Replies
View Related
Sep 11, 2014
I have installed no updates and made no changes to configuration in any way. Computer has been left on for some time. Finally rebooted to clear any caches. When it came up again the system does not recognise the monitor. So I get the default resolution. Not hardware as a windows install comes up fine.
Using Wheezy with MATE
Running on Haswell
Installed backport to stop crash on exit 3.13-0.bpo.1-amd64
I have tried several versions of live CD. These all give the same symptom - which is why I tried the windows install. So I suspect this is something to do with recognising the onboard graphics in Haswell.
I have googled and found, however, means using a shell script. This seems rather drastic and I don't want to go that way unless there is no other possiblity of a solution. In that post the output of xrandr is posted so doing the same here.
Code: Select all xrandr -q --verbose
xrandr: Failed to get size of gamma for output default
Screen 0: minimum 1600 x 1200, current 1600 x 1200, maximum 1600 x 1200
default connected 1600x1200+0+0 (0x138) normal (normal) 0mm x 0mm
Identifier: 0x137
Timestamp: 4622
Subpixel: unknown
[Code] ....
Resolution : Linux system does not like both DVI and VGA cable plugged in at the same time.
View 0 Replies
View Related
Aug 25, 2015
I have been a Debian user for some time already, and lately I experienced a weird behaviour regarding shutdowns/restarts. The thing is my computer shuts down very very slowly, but not because of HDD activity, nor because of CPU activity (as far as I know, I may be wrong). It stops at some point, and after that, it hangs between 5 seconds and... even 5 minutes. The time in which comes back to normal and continues the shutdown process varies and has absolutely no pattern.
This is where it hangs (the last line appeared because I disconnected the mouse):
View 4 Replies
View Related
Sep 21, 2015
As the object, when I shutdown or restart my system, this will stuck on black screen for about 30/40 second and then continue...
My system is debian testing with kernel 4.1.0-2
View 8 Replies
View Related
Aug 10, 2010
I am facing the issue that the PC not capable to shutdown or reboot; In order to debug that, htop tells me the running processes but all seems normal, I killed few but still cold reset is needed.There is certainly a problem somewhere. the best would be to know which process are weirdly hanging. It could make this testing debian bit better to know which package has these issues.
View 1 Replies
View Related
Mar 14, 2011
in configuring a fresh install of Squeeze. I discovered that it is possible to power off the system under gnome simply by pressing the power button or by selecting the "Shut Down" entry on "System" menu.However I need to restrict this option only to root. How can I do that?
View 7 Replies
View Related
Mar 11, 2011
I've added entries to my Openbox menu labeled Reboot and Shutdown. Problem is, reboot and shutdown h only work as root, and I never login as root. I've tried su-to-root -c reboot, but the menu entries remain unresponsive. I do not have sudo installed because I feel it is a security issue. However, I found that sudo reboot works with the menu entry, but only if my account is set to use sudo without a password in /etc/sudoers. I use tint2 as my panel, but have had no luck with finding a shutdown/reboot button.
View 4 Replies
View Related
Mar 25, 2010
Further to this LQ thread which Tinkster solved by suggesting the last command (thanks Tinkster) I have been exploring last -x reboot and have found that the reported duration is incorrect for the last reboot and shutdown when a old wtmp file is used. Not having a record for the following shutdown, last assumes that the system has been up until the current time and similarly for the shutdown.
The output comes in time order, latest first, each line showing the time of the reboot and the uptime from then to shutdown. Using last -x reboot shutdown to show the shutdown time, here's an illustration
Code:
shutdown system down 2.6.29.6-smp Sun Mar 7 15:35 - 03:02 (11:27)
reboot system boot 2.6.29.6-smp Sun Mar 7 09:35 (05:59)
09:35 until 15:35 is 05:59.
When the uptime exceeds 24 hours it is shown as (<days>+<hours:minutes) like this
Code:
shutdown system down 2.6.29.6-smp Sun Feb 21 12:39 - 13:20 (00:40)
reboot system boot 2.6.29.6-smp Sat Feb 20 09:39 (1+02:59)
09:39 until 12:39 the next day is 1 day 02:59.
The time in parentheses at the end of the shutdown lines is normally the time until the next shutdown.
So far so good. The incorrect output is for the last reboot and shutdown of an old wtmp file. Here's the output of last /var/log/wtmp -x reboot shutdown; last -f /var/log/wtmp.1 -x reboot shutdown
Code:
[snip]
reboot system boot 2.6.29.6-smp Fri Mar 12 07:42 (01:54)
shutdown system down 2.6.29.6-smp Fri Mar 12 01:31 - 09:37 (08:05)
wtmp begins Thu Mar 11 08:25:26 2010
[snip]
reboot system boot 2.6.29.6-smp Wed Mar 10 14:12 (15+01:42)
shutdown system down 2.6.29.6-smp Wed Mar 10 12:41 - 15:54 (15+03:13)
[snip]
The boot started at "Wed Mar 10 14:12" which had an actual uptime of 1 day 11:20 is reported as 15 days 03:13 which is the time from then until the last -f /var/log/wtmp.1 -x reboot shutdown command was issued. The time from shutdown to shutdown is similarly affected.
View 1 Replies
View Related
Aug 25, 2015
Every shutdown/reboot always hangs on
Code: Select allkvm: exiting hardware virtualization
I have tried rebooting/shutting down with
Code: Select allshutdown -h now
reboot
shutdown -r now
halt
init 0
init 6
And all hang on the same line. This is 100% reproducible. I am not actually running a virtual machine. I don't have qemu-kvm installed. I do have separate partitions on my system. I have a /boot, /, swap, and /home partition.
From looking at other posts: [URL] .....
Solutions tend to be across the board: not unmounting properly, acpi settings in grub, using a different shutdown command.
My fstab file is:
Code: Select all# /etc/fstab: static file system information.
#
# Use 'blkid' to print the universally unique identifier for a
# device; this may be used with UUID= as a more robust way to name devices
# that works even if disks are added and removed. See fstab(5).
#
# <file system> <mount point> <type> <options> <dump> <pass>
# / was on /dev/sda2 during installation
[Code] ....
and the result of Code: Select allmount is
Code: Select allsysfs on /sys type sysfs (rw,nosuid,nodev,noexec,relatime)
proc on /proc type proc (rw,nosuid,nodev,noexec,relatime)
udev on /dev type devtmpfs (rw,relatime,size=10240k,nr_inodes=498135,mode=755)
devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000)
tmpfs on /run type tmpfs (rw,nosuid,relatime,size=800408k,mode=755)
[Code] ....
View 2 Replies
View Related
Feb 20, 2016
How to run a script/command before shutdown/reboot in Debian Jessie.
I created a script myshutdown.sh in /etc/init.d/ to shutdown rTorrent if the reboot or shutdown now -h command was executed.
#!/bin/bash
#rTorrent Shutdown Script
echo "Shutting down rTorrent!"
kill -2 `pidof rtorrent`
I set the file as executable.
sudo chmod +x /etc/init.d/myshutdown.sh
I inserted a symlink in the rc0.d directory with the process order K04.
sudo ln -s /etc/init.d/myshutdown.sh /etc/rc0.d/K04myshutdown.sh
I also inserted a symlink in the rc6.d directory with the process order K04.
sudo ln -s /etc/init.d/myshutdown.sh /etc/rc6.d/K04myshutdown.sh
Apparently rc0.d is for shutdown and rc6.d if for reboot
After reboot it appears that rtorrent does not run (I cannot connect to rtorrent via rutorrent) but really what is going on. I am trying to do this because rtorrent does a hash check on all files if it is not shutdown properly. I just want it to shutdown automatically and safely, before the system shuts down.
View 9 Replies
View Related
Jul 5, 2011
Every time I reboot or shutdown my PC, the login window shortly pops up. The PC does shutdown or reboot normally afterwards. When I use the terminal to shutdown/reboot (sudo shutdown -h now or sudo reboot) all goes well. The PC is running Debian Squeeze with the GNOME desktop environment.
View 7 Replies
View Related
Jul 3, 2011
I am having slight issue with setting up file sharing. I have a windows 7 pc and hp proliant microserver running. I have a raid array which I am using as a share for storing music, pictures etc. When I reboot the debian server I can't connect to the server from the windows 7 PC (I have mapped a network drive) until I go on to the server and restart samba with /etc/init.d/samba restart - then everything works fine. I can ping the server with both ip and hostname but the network drive does not connect - this is straight after a reboot. Is the /etc/init.d/samba restart doing something differently to when the server boots? I have read several posts relating to printer sharing issues which point to samba not starting before cups so I am wondering if samba is starting before some of the relevant networking services.
View 2 Replies
View Related
Nov 30, 2010
So I found many methods on google, but no one works. It seems that this one is THE Debian way.
Code:
### BEGIN INIT INFO
# Provides: mystartupscript
#[code]...
View 5 Replies
View Related
Mar 30, 2010
I'm trying to reboot the server (shutdown -r now).But it seems like nothing happened.
When I try "shutdown -c", the system prompts "shutdown: cannot find pid of running shutdown."
View 5 Replies
View Related
May 17, 2010
I have a recently new, less than 2 weeks old, Ubuntu 10.04 LTS installl. It is a clean install since the prior install of 10.04 LTS decided it would no longer allow me to login.
My problem is that I cannot shutdown or restart my machine. And I have no idea why it happened.
View 9 Replies
View Related
Apr 28, 2011
I have just installed 11.04 on my Acer Z5610 and it won't shutdown or even restart noramally. I have to force shutdown every time. I installed the ati graphics drivers but still no change. What could be wrong?I have reinstalled 4 times, using usb and cd.
View 9 Replies
View Related
Jul 8, 2011
I have assembled an Intel D915PDT Administration Intel Desktop motherboard with an Intel 651 Processor which has 3.40 GHz 800 MHz FSB 2MB L2 Cache and 1GB DDR1 400 MHz RAM also GeForce 8400GS 512 Graphics Cards. But this PC have a problem, if once I shut it down I cant restart it again, but the next day it works properly. I tried in various operating systems like Windows XP service pack 2, pack 1, Windows 7 Professional and Ultimate 32bit and I have checked several times the BIOS settings properly but the problem is still the same.
View 1 Replies
View Related
Nov 26, 2009
I'm running openSUSE 11.2 Gnome Desktop Environment. Whenever I try to either shutdown or restart my machine as a "normal user", I've been logged off instead! When I try to re-login the screen (xorg) freezes. I don't know how to debug this problem. The problem could be related to hal or d-bus or policykit or X-org..... simply I don't know. N.B. I can shutdown and restart my machine only as "super-user" (root).
View 9 Replies
View Related
Jan 26, 2011
I had my netbook which is an Acer AspireOne lock up on me once earlier today and after doing a hard shutdown *holding the power button* and booting it back up I noticed that I could no longer reboot the machine from KDE's graphical shutdown button. Basically I click it and it pops up with the 30 second count down and then nothing. However I can run as root,
Code:
Shutdown -r now
and it will comply and reboot. I did notice that rngd was returning an exit status 1 and after some research decided to uninstall it with no change to anything. I decided to attempt and see if it was just a KDE issue as many problems have been, but when I attempted to log into Gnome I got a very nice white screen with one black line where the taskbar should be. Whether they are related or just coincidence I don't know.
I've ran my google researching skills into the ground on this one and I'm tired and a bit grumpy because I haven't been sleeping so it'd be awesome if I could get a heads up, because to my knowledge it's not reporting any errors it just seems to hang without sending the shutdown signals.
View 1 Replies
View Related
Feb 19, 2010
I'm in 9.10, I had KDE 4.3 now with SC 4.4, and it doesn't reboot or shut down from any graphical way I can access. Power management works otherwise, and I can shut down from the command line.
View 6 Replies
View Related
Apr 3, 2011
I have just installed ubuntu 10.10 so i am new to linux operating systems.In the top right hand corner where the shutdown button is with the options to restart, mine is not there.Could someone please tell me how to get back this button or another way that I restart so I can access my windows boot?
View 3 Replies
View Related
May 3, 2011
Whatever I do, I can't get my linux to reboot, shutdown or hibernate.
Here is some new info:
I am using stripped down xfce4 with compiz and emerald.
Here's my .xinitrc
Code:
and my startup script
Code:
1. My login manager is SLIM which I use to autologin.
Code:
2.
Code:
3. Here is what happens when I try to reboot with the .xinitrc file I published above - it freezes on console login screen: [url]
4. Here is what happens if I change the .xinitrc file to this:
Code:
And script file:
Code:
It won't even login: [url]
View 2 Replies
View Related
Apr 21, 2010
A few days ago an upgrade to FF 3.6.3 was pushed at me by Mandriva. I accepted it, of course.
Since then, firefox refuses to restart after a shutdown, and there are no error messages in any log or in the bash window if I try to start it that way.
I tried a couple of times to uninstall/reinstall it, but no joy.
Finally figured out that if I reloaded the .mozilla directory in my home directory from a daily backup, FF would restart.
This suggests that FF 3.6.3 is corrupting something either while it is running or when it shuts down.
It's pretty consistent, and makes it rather hard to use FF. The lack of error messages is making it rather difficult to sort out.
View 5 Replies
View Related
Mar 25, 2010
I'm sure there's an underlying hardware problem for this... but I figured I'd start here as I do not know the specific hardware issue.
I'm in Ubuntu 9.10 (Ubuntu Studio actually) and my computer will not shut down properly. I get the splash, then a black screen, then something like #terminating processes, #closing connections, #blah blah blah, #will now halt(or will now restart if rebooting)
View 10 Replies
View Related
Feb 7, 2010
I'm running Fedora 11 with KDE desktop. Yesterday I installed several updates, including a kernel update. Now the Shutdown and Restart icons have disappeared from the Leave menu, which only contains the icons for "Logout", "Lock", "Switch User", "Suspend to Ram" and "Suspend to Disk". I had "Shutdown" and "Restart" icons in my Favorites menu, but when selected they open a "Logout" dialogue.
I can Shutdown and Restart from the command line, but would like to restore the capability to do it from the icons. Has anyone else experienced this and found a fix?
View 12 Replies
View Related
Jul 23, 2010
Logout, Suspend and hibernate works as it should in my gnome-shell desktop.But Shutdown/Restart does not - I just get back to my kdm login screen again...how do I enable this ?
View 5 Replies
View Related
Dec 15, 2009
Pressing the shutdown or restart buttons in XFCE simply logs me out and leaves the system running. I did some Googling and it was suggested that by default users don't have permission to shutdown. (not sure how this is a XFCE specific problem in that case but moving on...)
I've taken the following advice:
For a "desktop" system that wants to protect itself from casual attacks (and "puzzled penguins"), but still grant the user control of their system, run the following as "root":
USER=<your_userid>
polkit-auth --show-obtainable | while read OPT; do
polkit-auth --user $USER --grant $OPT
done
Where <your_userid> is the name of your unprivileged account. I wasn't entirely sure how to run it, so I stuck it into a shell script and ran that with the sudo command. Needless to say it hasn't worked. Is there an easy "sure fire" way to fix this problem, hitting the shutdown button repeatedly to test really grates on you after a while. BTW, Pressing the power button on the front of the system shuts it down okay.
View 5 Replies
View Related
Aug 9, 2011
recently I installed opensuse 11.4 in my Dell optiplex 790 desktop. everything works well. however, when I tried to restart or shutdown my computer . the computer logoff and then "freeze" at opensuse window. I have to turn off the power button forcely and turn on the computer again.
My computer configuration:
DELL Optiplex 790
Intel i5 3.1G with HD intel graphic card
Bios revision A05
Memory 8G
View 9 Replies
View Related