Debian Hardware :: NVidia Binary Driver Causing Hot GPU In Wheezy / Fix It?
Apr 21, 2011
Having upgraded to kernel 2.6.38 in wheezy, you now have to blacklist the nouveau driver as just uninstalling the packages don't seem to be enough as it is with squeeze. The latest nVidia 270 driver makes my GPU run over 10°s hotter. The 264 driver in the Debian repo has the same effect. I can't install the 195 driver (which I know is ok with my GPU), for some unknown installation error (error 1 during compile).
I have a GeForce 7950GTX on my Dell laptop. The hardware is ok, as the temperatures are much lower with squeeze, and I have cleaned inside the laptop.
Is anyone else having any issues with excessive heat with nVidia? Could this be a driver or a kernel issue?
And why did I have to blacklist the nouveau drivers even though they weren't installed?
Previously running Squeeze I was using the proprietary driver and never had any issues. Now using the nouveau driver video playback of mp4 files is glitchy and programs like google earth don't operate smoothly. I installed the nvidia driver from the repositories based on this guide, used nvidia-xconfig to generate an xorg.config file. I made sure noeveau was blacklisted and rebooted my machine.
I was greeted with a black screen. So I booted up in recovery mode, used telinit 2 (side note: what happened to /etc/inittab???) to change to a runlevel that doesn't start X, and confirmed that nouveau was, in fact, not loaded. Typed startx and without any errors or warnings the screen went black. ctrl+alt+fN wouldn't bring me back to a terminal, but hitting the power button did shut down X and halt the machine.
I'm not really sure how to go about debugging this as I get no useful output from anything, just a blank screen and that's it.
For the time being I just blacklisted the nvidia driver and let the system boot with nouveau; I'd still like to get the nvidia driver working properly, though. I've always just downloaded the driver right from nvidia and installed it, but I know that isn't the best way to do it. I'd rather not screw up a brand new system, it's so nice and fast with the new SSD.
I'm encountering a problem running X and Gnome from a Xen-enabled Kernel with NVIDIA Binary driver compiled with IGNORE_XEN_PRESENCE=y on debian squeeze
Hardware: NVIDIA NVS 5100M Kernel: Debian Squeeze : 2.6.32-5-xen-amd64 NVIDIA Kernel from the official package
Boot and module loading are successful, but when X starts, I only get a black screen. I attached here my Xorg.0.log, however it doesn't seems to have any problem.
I'm on Wheezy with version 304.117 of the proprietary nvidia driver installed and working, but an application I have needs a newer version of the driver. I'm trying to install the 319.82 version in backports by following the instructions given here, but when I issue the command to install nvidia-kernel-dkms, I get the following:
The following NEW packages will be installed: Â libgl1-nvidia-glx-i386:i386{a} nvidia-driver{a}
The following packages will be REMOVED: Â libgl1-nvidia-alternatives{u} libglx-nvidia-alternatives{u} Â libxvmcnvidia1{u} nvidia-glx{u}
The following packages will be upgraded:  glx-alternative-nvidia glx-diversions libgl1-nvidia-glx  libgl1-nvidia-glx:i386 libnvidia-ml1 nvidia-alternative  nvidia-installer-cleanup nvidia-kernel-dkms nvidia-settings  nvidia-smi nvidia-vdpau-driver xserver-xorg-video-nvidia
The following partially installed packages will be configured: Â mint-flashplugin-11:i386 12 packages upgraded, 2 newly installed, 4 to remove and 151 not upgraded. Need to get 32.3 MB of archives. After unpacking 9,440 kB will be freed.
The following packages have unmet dependencies: Â glx-alternative-mesa : Depends: glx-diversions (= 0.2.2) but 0.5.1~bpo70+1 is to be installed. Internal error: found 2 (choice -> promotion) mappings for a single choice. Internal error: found 2 (choice -> promotion) mappings for a single choice.
The following actions will resolve these dependencies:
   Remove the following packages:                   1)   glx-alternative-mesa                       2)   glx-alternative-nvidia                      3)   libgl1-nvidia-glx                         4)   libgl1-nvidia-glx:i386                      5)   nvidia-alternative                        6)   nvidia-kernel-dkms                       Â
[Code] ....
Accept this solution? [Y/n/q/?] q
The mint-flashplugin problem is a separate issue which I've had for a while. I assume that it can be ignored for the purposes of this post.
If I'm reading the aptitude output above correctly, it's telling me that the only way to "resolve" the conflict is by uninstalling all nvidia support, leaving me with no driver at all. Is that right?
How do I check if I'm using the Nouveu driver or the Nvidia Binary driver? I thought things were running nicely with the free driver because I had compositing working on my dismal graphics card... But scrolling in firefox is slow/laggy so I tried installing the binary driver with 1click install. But I restarted and still have the same problem. I think I might still be using the nouveu driver? Actually, scratch that last sentence. I just did lspci -v and got this output:
Code: 01:00.0 VGA compatible controller: nVidia Corporation NV37GL [Quadro FX 330/GeForce PCX 5300] (rev a2) (prog-if 00 [VGA controller]) Subsystem: Giga-byte Technology Device 310e Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at f0000000 (32-bit, non-prefetchable) [size=16M] Memory at e0000000 (32-bit, prefetchable) [size=256M]
I'm running Ubuntu 10.10 on an old small form factor PC with an AMD Sempron 2400, 1GB RAM, and an nVidia 5200 graphics card 128MB. OK, so a low-spec machine (but that's the great thing about Linux right? Don't need high-end h/w) but it works just fine, except that it can't play full HD (1920x1080) MPEG-4 video. Very jerky and lots of dropped frames. Same in both Movie Player and VLC.
I can't afford to increase the RAM and as it's a SFF I can't just swap the mobo and CPU for something faster so I'm wondering whether getting a higher spec graphics card would make any difference?I'm using the nVidia proprietary binary driver (latest version) and searching the forums I found a post where someone said that the nVidia driver needs at least a 512MB card for HD video.A colleague has a higher spec nVidia card (7600 IIRC) that he'll sell me, but before I spend any money, is this likely to improve things? How much does the graphics card affect performance, or is it simply a case of the machine overall just isn't high enough spec?
I'm having all sorts of problems after doing my first update (#1. safe-upgrade, #2. full-upgrade) in over a month.
Anything from no Nvidia linux-headers being found to any VT not working. After completely removing all of the previously tried Nvidia presence on my PC, is there a safe way for me to install the non-free drivers?
When I install the ATI graphics driver, sure - I get all the screen resolutions I could possibly want, but the cost appears to be that it makes it causes my system to freeze at the user name and password screen. Sometimes the cursor blinks teasingly, but nothing appears as I type; sometimes the cursor itself is frozen.
My question isn't about the myriad of theoretical key combinations that might work - none of them have thus far.
I'm wondering whether I can simply continue using the default driver that the debian installer (ver. 8 stable 'Jessie') installed on my system. It's true that I only get 3 choices of screen resolution - 1152x864, 1024x768, and 800x600 - but my system seems so much more stable than when I install the proprietary ATI driver.
Aside from the login screen freezing - more often than not, strange things were happening keyboard wise - especially when composing posts for forums - the cursor would suddenly jump to another line of previously composed text for example!
So, can I keep the default driver or is it best to install the ATI driver and attempt to troubleshoot it? Is it even possible to troubleshoot a problematic driver - I knew how to do such things in Windows, but still learning about linux.
Also, when my system freezes at login (for whatever reason), if I'm obliged to simply hit the laptop power button to power down and press it again to restart - is this potentially damaging/corrupting my system - Debian, or indeed my hard drive?
Going forward, is the ATI driver issue likely be addressed in future Debian releases? Obviously, I would prefer to have the proper driver installed so as to have more screen resolution options - since I will be using my laptop for developing and testing web sites.
When i finish install debian7.8 wheezy in my Acer computer(graphics :GT750M+ Inter HD Graphics Family),
it appear:
"GNOME3 Failed to Load" " Unfortunately GNOME 3failed to start properly anmode" "This most likely means your system(graphics hardwcapable of ....."
i check system's Driver status:Gallium 0.4 on llvmpipe(LLVM 0x209) Experience Fallback so i try to install nvidia drivers in debian,but i have failed many times. everytimes i finish install nvidia drivers i 'startx " failed
Just did an install and am loving Debian. I am having troubles with my card causing mini-freezes. I type and the input sometimes(every 30 seconds) stops and then catches up. This is really annoying. I figure it is the wireless driver because when I ran top -d 0.1 Ieee80211/1 or Ieee80211/0 was the main verdict during every stall. I have not had this problem with other distros, but came to Debian for stability. Any ideas on how to fix it?
Recently, I installed VVVVVV and discovered that when attempting to use fullscreen mode, the monitor displays "video mode not supported" for 640x480, 800x600, 1024x768, and auto. After googling around for an hour or two (and only finding stuff from 2008-09) I have created a new xorg.conf from Xorg -configure and nvidia-xconfig. This doesn't seem to have had anyeffect.DebianRelease unstable (sid)Kernel Linux 3.0.0-1-amd64GNOME 3.0.2GeForce 7600 GSMonitor: Hyundai Imagequest
$ cat /etc/X11/xorg.conf # nvidia-xconfig: X configuration file generated by nvidia-xconfig # nvidia-xconfig: version 280.13 (pbuilder@cake) Mon Aug 8 15:37:15 UTC 2011
I need to install wheezy nvidia-graphics-drivers because my video card (geforce GT 425m) isnt supported on the squeezy version. I downloaded the wheezy source code and built it on my squeezy system, some .deb files where created, the problem is I dont know which of those to install, these are the files:
I want to use the open source radeon driver. My video card is AMD/ATI RADEON HD4850. I want 3D acceleration even if it's inferior to fglrx's although I would like if it exceeded fglrx's performance but the performance of the driver is not the point of this thread. Fortunately, fsck was checking the hard drive upon booting so I had time to write the boot output in this computer which I believe would be of help.
Video card: Failed to load firmware "radeon/RV770_pfp.bin" *ERROR* Failed to load firmware! disabling GPU acceleration
gdm3: rt2x00lib_request_firmware: Error - Failed to request firmware. I attempted to install firmware-linux and do sudo gdm3 but all that did is say gdm3 lasted for 0.x seconds where x changes and it kept re-printing that sentence infinitely. I also rebooted and tried to let gdm3 start itself.
Firstly, I'm assuming the open source driver relies on proprietary firmware. Why is this the case? Secondly, how do I get the radeon/RV770_pfp.bin firmware? Is it not in the firmware-linux package? Why does it matter that GPU acceleration is disabled for loading gdm3? Isn't simple 2D enough? (I'm not saying this because I don't want to have 3D enabled since I do want it enabled but because I would imagine that 2D capabilities are enough to load gdm3). If more information is needed, just ask.
I have wheezy up to date and the xserver-xorg-video-radeon package is at version 6.14.2-1. I am using the linux-image-2.6.39-2-amd64 package as well for the kernel. When I boot, it stays on the tty1 console and I can't start gdm3 manually (it also doesn't start automatically).
I've bought a HP Pavilion laptop on which Ubuntu was pre-installed. i had to switch my OS into Debian Wheezy. But now i can't find the wifi driver for my network card. [MEDIATEK Corp. Device 7360].. I tried upgrading kernel to 3.13.6.. But couldn't make my wifi driver work....
Currently using Nvidia driver version 195.36.31, it's the version that works with Nvidia-kernel-dkms, would updating Nvidia driver to the current 275.09.07 driver version break my setup?
install debian 6 on my pc and have big problem with videoadapter driver i cannot install driver i dowload driver from nvidia do something in google but nothing! palit gtx 460 linux debian 6 x64.
BlizzPlanet reports that people are seeing their nvidia graphics cards overheat when running the Windows 196.75 driver and playing 3D games. I have to wonder whether I fell afoul of this issue. A week ago I installed the 195.36 nVidia proprietary Linux driver on my Karmic Koala system, after adding the PPD nvidia-vdpau repository to my sources.list. I restarted so the new driver would take effect... and was surprised to see the graphics chip temperature soar to over 130 degrees Celsius. It fried itself. When I opened up the case, I checked the card's fan, and it spun freely, and I'd not heard any noise of the sort that accompanies a dying fan. I'm sticking with 190.53 for now. Has anyone else seen overheating difficulties with the 195.36 driver?
I installed Debian Squeeze with no issues. I went to install latest Nvidia driver as done previously with Lenny. Used instructions that worked on lenny from "the trooper" [url]
Downloaded th latest driver for my GeForce 7300 GS vidio card, driver package NVIDIA-Linux-x86-260.19.12.run
Used "method # 2 as described in HOW TO,as it worked perfectly in the past on Lenny. Only syntax I changed was instead of gdm I typed gdm3 as it appears that is the new name for gnome in Squeeze.
Did as folows:
Now the trouble showed up, Unfortunatly I can only go off my memory. A question was asked stating that something did not match, it needed a 3 and the driver had a 4 version or somethng of this sort. then it asked if I new what I was doing (and I lied) and selected yes. And whammo, it didn't work. (This question was asked when i did in Lenny and it is working perfectly still on that system). I now can not boot to GUI, I notice when system boots it starts in "S" mode although I select normal boot from grub2.
Not too bad if I got to reinstall as little is on the system. I just want to know what I am missing on the instalation deal or should I be going about this difrently with Squeeze.
You know, the "ctrl+alt+F5" type things, where you go to those pure command lines? I installed Ubuntu 10.04 from scratch, and everything was working great! Good resolution, etc. When I booted up my computer, the (very brief) splash screen fit the entire resolution of my monitor (1680x1050), and the X server did the same.
When I'd go to one of those 'tty' terminals, I was surprised (in a good way) to see that they had scaled to my monitor's resolution as well. I was looking forward to using that. Well, time came where I wanted to turn on Compiz, so I downloaded/installed the nVidia drivers. Well, they work. I can work with Compiz and 3D games at full speed and full resolution in Ubuntu, and I have zero complaints about that.
What I do have a complaint about is that the terminals (tty5, in the above example) are back to that old resolution, 640x480 I believe. Also, that brief splash screen is at the same horrible resolution, instead of the full resolution I had on the old nVidia driver that didn't support 3D effects.
Is there a way to get that back? Is it a bug or a glitch that it's no longer scaling the tty's to my display resolution, and do I just have to wait for an update?
I installed the Nvidia installer: NVIDIA-Linux-x8~.86.14-pkg1.run I configured the xorg.conf file and changed the driver from nv to nvidia. I also removed "load dri"
When I use startx I get this error and it won't give me a desktop:
(EE) Failed to load /usr/lib/xorg/modules/drivers/nvidia_drv.so (EE) Failed to load module "nvidia" (loader failed, 7) (EE) No drivers available
This is all I remember doing with Lenny. Apparently there is something else I need to do with Squeeze?
I have installed before with ease following the Debian how to. On jessie 8 I have an issue with black screen, probably miss configuration but can't figure what?
I am trying to install the non-free NVIDIA drivers. I have read the guide here [URL] but what they didn't mention is what to do when you have a graphics card that isn't supported in Debian Lenny's repo driver version. I have the GeForce GTS 250, which isn't listed under the 173.14.09 (the stable repo version) supported VGA cards list. The version I need can be found in Sid and Squeeze (195.36.24 currently). If I add the Sid repository, it seems to work but it returns a whole lot of other unrelated package updates and its really annoying since I don't want to change to Sid yet. So how do I keep the rest of my packages under Debian lenny with only the minimal amount of packages to be under Sid.
I tried APT pinning once but the standard '*' won't work unless if it's alone in the 'Package' line. To clarify, a line like: Package: nvidia-* would get ignored. I would also need a list of required packages and dependencies that must be installed from Debian sid to get this to work. The documentation for APT didn't help much. I can usually get around this problem by using the NVIDIA way but then I can't boot into Gnome GUI at all under other kernel versions except the one I compiled it for, unless I use the terminal to restore the Xorg stock drivers.
If i run nvidia-xconfig, it will say driver not found, and the next time i boot, it will end up in a terminal. why is it so? (by the way i recovered from that using backup of xorg.conf). And i dont think now the nvidia-driver is present.
The nouvea drivers work with some xrandr magic, but the closed-source drivers won't. They fail to detect a possible resolution over 640x480. My monitor has a native resolution of 1440x900 @ 60hz. I've tried to modify my xorg.conf, but to no avail. I installed the latest nvidia drivers from the site instead of the repo drivers, version: 260.19.29, this is my xorg.conf, basically a standard xorg file:
# nvidia-xconfig: X configuration file generated by nvidia-xconfig # nvidia-xconfig: version 260.19.29 (buildmeister@swio-display-x86-rhel47-04.nvidia.com) Wed Dec 8 12:27:39 PST 2010 Section "ServerLayout"
hHey i recently installed Debian Squeeze 64bit over my Ubuntu & Windows, i got everything installed and running including all programs i need without a single problem The one thing i havent been able to do yet is install the Nvidia Driver for Geforce 8800gt, ive searched a few sites but one site is telling you to do this way and the the is telling you to do it another way then people are saying about having errors when xorg updates and stuff.
So i was wanting to know whats the easiest and best way to install the Nvidia Driver package (from nvidia website) onto Squeeze 64bit, i've done it on lenny but cant remember ow
If i get this working then il probaly use Debian as my main OS from now on.
i've installed debian 8 on this laptop but can't use the nvidia card from nvidia-detect can't find the card but it work 'cause i can see it in the list of hardware, 3d controller the driver from nvidia don't work, and i had a problem with force installation and xorg.conf file.. how i can make it work ? the card it's nvidia 820m
I recently installed Squeeze. I had sound with the video driver that came with the install. Then I installed the Nvidia driver from Nvidia website. The sound dissappeared. When I uninstalled the Nvidia driver and removed xorg.conf and rebooted again, the sound came back. Then I installed the Nvidia driver from (nvidia-glx, dev and settings) from Debian with Synaptic. The sound went away again. If I uninstall the nvidia driver and xorg.conf the sound will probably come back again. The sound driver is the one that came with the install.
The volumes are unmuted in the alsamixer. Somehow alsaconf command does not work.
My mother board is a ASUS M4N78 Pro with Nvidia IGP.
What can I do to have sound with the nvidia driver?
