Does Debian have any particular tools or nuances for installing new hardware? I saw some stuff on Ubuntu which is related... but you know.
The dmesg file shows that it's being recognized, but I don't think it's actually being used (i.e. there is no driver installed). This is what's in the dmesg file:
Unless someone has already compiled a driver for Debian Lenny for this hardware, I'm going to have to compile my own I guess. The driver package seems to come with something called mptlinux-4.00.43.00-src.tar.gz which I'm guessing can be compiled for any Linux, but looking at the instructions, it's pretty much beyond me how to get started. It talks about using kernel source to build a module and such and such.
i m facing same error in most of the HCL servers. the problem is that it throws error while booting and sometimes not throws error. the error is :-
Feb 13 13:17:25 fe13s kernel: Adapter 0: Bus A: The SCSI controller was reset due to SCSI BUS noise or an invalid signal. Check cables, termination, termpower, LVDS operation, etc.
Feb 13 13:17:30 fe13s kernel: Adapter 0: Bus B: The SCSI controller successfully recovered from a SCSI BUS issue. The issue may still be present on the BUS. Check cables, termination, termpower, LVDS operation, etc
Feb 13 13:29:15 fe13s kernel: Adapter 0: Bus B: The SCSI controller successfully recovered from a SCSI BUS issue. The issue may still be present on the BUS. Check cables, termination, termpower, LVDS operation, etc code....
I have a Dell PE 600 box with 2 Adaptec 2110s U160 Single Channel RAID controller supported 6 HDDs.I am trying to install Ubuntu from a mini ISO - tried server / desktop / alternate as well. And also different Ubuntu versions.The mini installer runs upto setting the time zone (after configuring for DHCP et.al.) and then on the screen 'Detecting Disks and Other Hardware' hangs up.Now I am assuming its because of the fact that I have 2 of the above controllers - as I have another similar box with only 1 of the controllers and it installs/boots fine with no problems.Look forward to you suggestions/help and if there is any other info I can provide. I plan to set up Ubuntu 10.10 server on it. Btw I don't think its a Linux problem as SUSE 11.3 installs fine on the box.
i am writing block deriver for usb device in linux i want to read and write data to/from usb device i already registered usb device with my driver and opened the handle for the usb device now i need to send scsi command to usb device to make it work but i dont have knowledge about scsi commands and how and where to use them now i need to know which scsi command i need to pass to the usb device and how can i pass that command to usb device also i need some information like how to register host controller with my usb driver
if anyone knows about this or where can find the tutorials / documentation/ framework for the same.
I have a dell PC running on Fedora 12, and I would like to install this SCSI controller card from adaptec:[URL]I see that the driver for Linux is available only as source code. Can somebody please indicate me how to proceed? I am not advanced enough in Linux to know what to do with it myself...I downloaded the most recent (v2.0.26) Source Code for Linux Kernel v2.6 on all platforms.Here are the contents of the tarball (if it helps in any way):
When I enter "cat /proc/scsi/scsi" I'm returned with "cat: /proc/scsi/scsi: No such file or directory". I've tried this on two different installs on two different machines.
Im trying to install Debian on my server. Some hardware descriptions:
- Inel Xeon processor - 03:01.0 RAID bus controller: Adaptec (formerly DPT) SmartRAID V Controller (rev 01)
There is configured by hardware one RAID 5 on four scsi disks of 73GB. I tryed with Lenny and Squeeze versions and both presented the same error when the install try to install grub:
main-menu[1250]: INFO: Falling back to the package description for auto-install main-menu[1250]: INFO: Falling back to the package description for ai-choosers main-menu[1250]: INFO: Menu item 'grub-installer' selected
In my understanding, the way /proc/scsi/scsi gets populated, /proc/paritions also gets populated in the same fashion. i.e. the description for first entry of /proc/scsi/scsi can be seen in the first entry of /proc/partitions and same for rest.
So, With this assumption, in my project, I used to relate first entry of /proc/scsi/scsi with first entry of /proc/partitions to get its total size and same for all entries.
But, I observed some differences in following scenario, where
1) The first 4 entries in /proc/scsi/scsi are SAN luns attached to my system and for which the actual device names in /dev/ are sda,sdb,sdc and sdd.
2) The last 4 entries are the internal HDDs on same system. In /dev/, their respective device names are sde,sdf,sdg & sdh.
(Output attached at end of the thread)
But in /proc/partitions, the device order is different.
You can see their respective sizes in /proc/partition output as well.
So, my question is, in this particular scenario, I can't relate the first entry of /proc/scsi/scsi with first entry of /proc/partition. i.e. scsi0:00:00:00 is not /dev/sde, because it is actually /dev/sda.
It seems that my assumption is wrong in this scenario.
Is there any way or mechanism to figure out actual device name for an entry in /proc/scsi/scsi in /dev/ directory?
How can my application should relate /proc/scsi/scsi entries with their respective device names and sizes?
Some of our workstations have LTO's attached and they seem to drop off every now and again, the only thing which picks them up again (besides a reboot) is the famous rescan-scsi-bus script from here
The thing is that I'd like non-root users to be able to run this script, which in turn needs root to /proc/scsi/scsi
I can not get the node or cloud controllers to startup using the init.d scripts. I have a fresh install of CentOS 5.4 with Eucalyptus 1.6.2 I have compiled Eucalyptus and all packages using the RPM supplied from Eucalyptus and utilizing yum installer. I do not currently have any processes or applications listening currently on the ports on the boxes as well. I think it may be a permissions issue or something because I get a "permission denied error", but I am not sure if it is Eucalyptus or CentOS. It looks as if it is not binding to the address on the interface of the NIC. It may be something else however. I have the Node controller, Cloud controller, and Cluster controller on seperate physical boxes. When I try to run either the cloud controller or the node controller I get this message:
Cloud Controller:
[root@cluster-cont ~]# /etc/init.d/eucalyptus-cc start Starting Eucalyptus cluster controller: (13)Permission denied: make_sock: could not bind to address [::]:8774 (13)Permission denied: make_sock: could not bind to address 0.0.0.0:8774
I installed OpenSuse 11.4 (x86_64) a couple of days ago.One of my Drives a PC-DVD RAM (Creative) is not working. This worked under 11.3.The SCSI drive is connected to a PCI/SCSI adapter (AHA-2904).The message I see at boot is: ata_id[443]HDIO_GET_IDENTITY FAILED /dev/sr1I also see the message ata_piix not found, and can not find an option in the kernel to provide this.his causes the system to wait a long time and slows down boot dramatically
Dist-upgrading to debian wheezy (gnome2.30.2) prevents me using a scsi HP 6200C scanner. I tried both
startx gnome-session and startx exec ck-launch-session gnome-session
In both cases:
$ ls -l /dev/sg* crw------- 1 root root 21, 0 Jun 27 16:21 /dev/sg0 crw------- 1 root root 21, 1 Jun 27 16:21 /dev/sg1 crw-rw----+ 1 root cdrom 21, 2 Jun 27 16:21 /dev/sg2 crw-rw----+ 1 root root 21, 3 Jun 27 16:21 /dev/sg3
instead of the expected "root scanner" to which affording permission (as it occurred with previous gnome in sqeeze). Incidentally, a flash card is not automatically mounted (no permission) but was solved by manual mounting as vfat.
Basically i want it so that the analogue stick on my PS2 controller, which connects via a USB adaptor and is recognized, correctly controls in game characters. It seems to work fine enough in platformers, at least it does with Banjo Kazooie, but with games like perfect Dark it seem to be trying to move forward and look down at the same time, also backward and look up simultaneously and look sideways and move sideways simultaneously , rendering the game all but unplayable.
I have tried running jscal and, apart from the fact that it seems a bit beyond me, it reports "jscal: missing devicename" when i try to run "jscal -c". Do others out there have there analogue sticks working correctly with games like Perfect Dark, or the James Bond games, for example?
2. lsscsi output -I installed lsscsi and here is the output: Code: Select all# lsscsi --device [0:0:0:0] cd/dvd LITEON CD-ROM LTN485S JKF1 /dev/sr0 [2:0:0:0] disk HP Net Mirror V1.0 /dev/sda [2:2:0:0] disk HP 9.10GB C 80-P94N P94N - [2:2:1:0] disk HP 9.10GB C 80-P94N P94N -
[Code] ....
3. force scsi scan -I tried to use this command to force a rescan for the hdds, but nothing happened: Code: Select allecho "- - -" > /sys/class/scsi_host/host3/scan
-no errors, but log says nothing -tried the above with host0 - 4, same result
4. fdisk -l Code: Select all# fdisk -l
Disk /dev/sda: 9098 MB, 9098887168 bytes 255 heads, 63 sectors/track, 1106 cylinders, total 17771264 sectors Units = sectors of 1 * 512 = 512 bytes
[Code] ....
5. tried to specifically add one device but it didn't work: Code: Select all# echo "scsi add-single-device 2 2 8 0" > /proc/scsi/scsi -bash: /proc/scsi/scsi: No such file or directory
First off I'd like to say I'm very new to Ubuntu, so I'm still trying to learn.I have a K8 motherboard with an adaptec U320 SCSI card with RAID ability.To that card I connected two 15k RPM 35 GB Maxtor SCSI drives.For some reason I'm not able to install Ubuntu 9.10 onto these drives with both drives in RAID 0.With both drives separately configured Ubuntu doesn't even see them.I have by the way run Windows XP and 2000 succesfully on these drives in Raid 0 configuration.I set up the array in the card's bios as bootable with write cache enabled.The system's bios sees the array as the array to boot from.Ubuntu (both standard and alternate) sees the array and I have tried to install Ubuntu on it by manually partitioning it or having me guide it with or without LVM.I tend to delete and rebuild the array between attempts so I have a clean slate to start from every time I try.
I have no other drives (except the CD of course) installed on this computer.The whole installation goes very well untill the end where I get a message that it could not install the boot loader (grub?).Every single time I've tried to install Ubuntu in all sorts of ways onto my RAID 0 array I have run into problems installing that boot loader, and I've tried that card and those disks in another computer as well.Tomorrow I'd like to try to manually set up the partitions with a small /boot partition on a standard hard drive with / on the array, but if somebody please has any idea's on how I might get it working without having to rely on another hard disk (which might not even work of course)
Can an unattended Kickstart support both IDE (hda) and SCSI (sda)? The goal is to to create a new virtual machine from scratch. What I have works for Parallels in which a new VM defaults to emulate an IDE hard disk. It does not work for VMware Workstation which defaults to emulate a SCSI disk.
The relevant Kickstart section: bootloader --location=mbr --driveorder=hda --append="rhgb quiet"
I have successfully setup a FOG server to image my Windows clients, so I have tftp, pxe and anything else related to booting to a pxe server setup and rocking. What I'm trying to do now, is use the CentOS net install files to setup CentOS on an old server with no USB boot option, and a broken scsi cdrom drive (it's a Dell PowerEdge 2400, with a single PIII 733 and 1.25GB ram).
Using the FOG Projects gparted wiki entry (adding gparted to the pxe boot menu) I was actually successfully able to pull the net install files over to the PE, and install CentOS 5.5 via local ftp server. At first it kept erroring out (I kept picking and choosing individual packages from the package groups), so I thought it may be an issue with the GUI install (the python script kept spitting back errors forcing a reboot). In any case, I finally got through the GUI install, but now I need / want to know how to force a text mode install.
[Code]....
the bolded "append" line is where I thought I could force the text mode install script, but that didn't work. The vmlinuz and initrd.img files were both pulled form the net install iso, NOT the livecd. Would that have made a difference? If not, what / where / how should I force the text mode install script?
I cannot install 11.3 on a machine with an intel raid controller I have tried with raid 1 using the card and then setting the disks to individual raid 0 and letting suse raid them. With the card doing it the machines crashes as soon as it tries to boot the first time, with suse doing the raid I just get 'GRUB' on the screen It seems a lot of people are having similar problems, does any one have any pointers. 11.2 installs fine. I would try and do a bug report but every time I go to the page it's in Czech
I've bought a small embedded controller running with a minimized Lenny for armel. Minimized in a way that there is even no apt-get or dpkg installed on it, due to keep the memory footprint as small as possible.Is there a way to keep a "shadow" system in a directory on my Laptop (e.g. ~/armel), maintained with dependencies by a package manager like apt-get? This would allow to install addition packages including all dependent with a simple apt-get call.Of course, later I have to put the whole tree from my Laptop towards my embedded controller. I've already tried the following:Setup a directory tree behind ~/armel for apt by a copy from my laptops Lenny
"sudo apt-get -o DIR=~/armel -o APT::Architecture=armel update" to get the repositories, this works fine "sudo apt-get -o DIR=~/armel -o APT::Architecture=armel -d -f install" to download the full list of .deb packages, this works fine
Recently we bought a server machine in purpose of hosting game servers.Debian is the optimal choice for us but we have a huge problem.We have 2 x HDD Fujitsu MBA3300RC, 300GB, 15000rpm, 16MB [MBA3300RC] , but NO SAS-controller , so standard Debian DVD1 didn't recognized our HDD's during installation.Is there any way to install Debian on our machine without haveing to buy a SAS-controller? answer in "step-by-step" method, i am not very experimentated in linux.
I am trying to install Ubuntu ver.10.10 server on HP DL360 with 2 internal 36GB untra3 scsi drives. The installations seems to have gone fine but upon booting, the OS is stoping at the BusyBox menu with initramfs prompt. None of my boot or root filesystems is mounted here so I can not go further. I've searched all over the net for answers but nothing seems to work.
At the school i work in i have a server2k3 server that provides a domain to all the windows clients, aswell as a fedora server that acts as an imaging machine and webserver.
Im rather concious of the fact that if for any reason the Server2k3 server was to die there is no backup of active directory, or anything that can take its place whilst a replacement is found.
So is it possible to use a fedora machine with samba as a secondary domain controller? so it can be used as a login server, and has a copy of AD.
Can Debian act as a Windows Domain Controller? I'm just curious because my boss recently tossed out some old servers and I grabbed them. They're good machines but I can't afford to pay $1000 for Server 2003 R2 just to setup a domain at my place and run Endpoint Protection and such. I've never used a domain setup in Linux before so I thought I'd ask and possibly try to, if Debian/Linux is capable of such a thing.
However, I have the problem I can't see any devices on my IDE port in my Asrock P43 mainboard, because the VIA VT6415 IDE controller isn't recognized. I typed an 'lspci -k', and I can clearly see there wasn't loaded any module to handle this VIA PATA controller.
I have been having trouble installing a working Debian 6.0.1a (Squeeze) desktop; I cannot seem to get Xwindoes working (under KDE). Is it possible that my video monitor is simply incompatible with Squeeze? I am using an old but not ancient Samsung SyncMaster 997DF with PS/2 keyboard and mouse. Output of lspci -nn | grep VGA is: 01:00.0 VGA compatible controller [0300]: Silicon Integrated Systems [SiS] 661/741/760 PCI/AGP or 662/761Gx PCIE VGA Display Adapter [1039:6330]
When I compared the contents of /usr/lib/xorg/modules and output of kdm.log between my working (but no longer trusted) Lenny and my nonworking Squeeze, I found that the driver sis_drv.so seems to be loaded by my Lenny but not by my Squeeze, and someone said that Squeeze uses a new version of Xorg which is incompatible with SIS. If so, does that mean that I need to get a new monitor? A new motherboard with video controller? I never had a video card--- do I need one to use Squeeze with KDE?....
I have a computer and I need to know whether its Sata-controller supports hotplugging. Therefore I (think I) need to know which Sata-controller is used in my computer. Can anyone tell me how I can find that piece of info?
ps. Some info on the environment: It is running an AMD Geode processor which only support IDE and therefore the board has a Pata to Sata converter build in. When I do 'lspci' it only shows the IDE connection: root@voyage:/etc# lspci
00:01.0 Host bridge: Advanced Micro Devices [AMD] CS5536 [Geode companion] Host Bridge (rev 33) 00:01.2 Entertainment encryption device: Advanced Micro Devices [AMD] Geode LX AES Security Block 00:06.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96) 00:07.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96) 00:08.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96) 00:09.0 Ethernet controller: VIA Technologies, Inc. VT6105M [Rhine-III] (rev 96)
I've been trying for probably 10 hours now to get the bcm4306 driver working on Debian. I finally got it installed using ndiswrapper... However, now ndiswrapper says that the hardware is not present! When I run lspci, though, it lists BCM4306 as the network controller. What is going on, and how do I fix it? It's on a Dell latitude D600.
I have a very weird problem with a HP DL180 G6 server that uses this controller.
The server has 4 SSDs configured as separate logical devices (no hardware RAID). I can install Wheezy just fine (creating a software RAID1 from sda and sdb). I installed zfs on it and installed a Windows 2008 VM on kvm with the disk image stored on zfs. The entire server froze when Windows was installing updates.
I rebooted and everything worked again, this time I launched iostat -x 2 on a separate ssh session, here's whet I saw after the server froze again:
Thinking that zfs might be causing this, I destroyed the zpool, configured software raid on sdc and sdd, created a volume group and stored the image on a logical volume. The problem happened again.
I opened a ticket with the support of the company that provides the server and they updates the firmware of the controller. Now the server no longer froze while installing Windows updates, with lvm or zfs, so I went back to zfs.
Wanting to be sure, I launched iometer on the windows VM and set it to "4KB, 75% read 100% random" access pattern over 5GB of the Windows drive. The server froze after 7 hours.
I told the company that, and they replaced the SSDs with ones of a different model. I ran the test again and the server froze again, this time after 9 hours. I asked the company to replace the whole server. They did it (but kept the SSDs), I ran the test again and the server froze again, this time after 20 hours.
Now, this is starting to look like some kind of incompatibility between the HP controller and Debian rather than a problem with the controller. The settings are all default. It looks like the entire controller freezes because the system drives (sda, sdb) also show 100% busy despite not being under test from iometer.
