I have got a debian (v3.16.7-ckt25-2) for server (without X). There is a br0 bridge connected to eth0 network device. It works fine when I start it manually by
Code: Select all# ifup br0 but I cannot start automatically at startup.
there was a missing line in /etc/network/interfaces:Code: Select allauto br0
I have two ethernet NIC's on my debian server. One built-in Realtek [eth0] (attached to internet), and a PCI Nvidia ethernet card [eth1] (attached to my Win7 netbook). I used this guide to setup the bridge: url. It worked when I was behind a router. But when I moved the computer in front of the router, to direct connect to the internet, the internet stopped functioning on any device that I plug into my Nvidia NIC. The name of my bridge is 'br0'. Does anyone know how to fix it, so I can route the internet to my second NIC?
My Win7 netbook displays this at an 'ipconfig' command:
Windows IP Configuration
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix:
Link-local IPv6 Address.....: fe80::143e:4cab:f802:8611%12
Autoconfiguration IPv4 Address..: 169.254.134.17
Subnet Mask.......:255.255.0.0
Default Gateway......:
My Debian interfaces file:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo br0
iface lo inet loopback
# Set up interfaces manually, avoiding conflicts with, e.g., network manager
iface eth0 inet manual
iface eth1 inet manual
# Bridge setup
iface br0 inet dhcp
bridge_ports eth0 eth1
I have a debian squeeze box with dual NICs that I'm trying to configure with two virtual hosts. I'd like to have one of these machines act as a router for the 2nd NIC so I can plug in a switch and have a separate subnet.
Something like:
- Openwrt router 192.168.1.1 (firewall/vpn/stats for 192.168.1.0/24 domain)
- KVM machine with 2 NICs (192.168.1.2)
- Virtual machine #1 has a fixed IP of 192.168.1.3 (virtual nic)
- Virtual machine #2 has a fixed IP of 192.168.1.4 (virtual nic) but also controls the 2nd nic and routes 192.168.80.0/24
I'd like to use the 192.168.80.0/24 network for testing equipment without poisoning my existing network.
I'm trying to bridge connections between a wired and a wireless connection in one of my computers. I was told it was impossible due to low-level limitations in the wireless subsystem, but apparently theres a way if you somehow forward packets from one port to the other. Is there a way I can achieve this?
View 1 Replies View RelatedI am very new to linux.I have a network camera which only has an Ethernet port but no WiFi. Sadly no Ethernet port is available close to the camera.
Therefore I now bought a raspberry pi and installed raspbian to create a bridge into the wireless network, for connecting the camera to the internet.I now played around with the interface- and bridge configuration but I have problems with it.This is how my interfaces file looks like:
(The WiFi is secured with WPA2 Enterprise)
Code: Select all# interfaces(5) file used by ifup(8) and ifdown(8)
# Please note that this file is written to be used with dhcpcd
# For static IP, consult /etc/dhcpcd.conf and 'man dhcpcd.conf'
# Include files from /etc/network/interfaces.d:
source-directory /etc/network/interfaces.d
[code]....
The WiFi is connection works fine and I am in the internet using the WiFi.But I am wondering about eth0. The network parameters I specified are not the same as the parameters ifconfig tells me.Ip, Broadcast, Mask, nothing is as specified.It would be nice to give the camera a static IP that I can access it always with the same IP from the RaspberryPi.The Raspberry Pi itself gets always a new IP from the WiFi network. How do I get the camera into the internet using the existing connection of the Pi?
I'm attempting to use a network bridge to connect my virtual machine, like so:
[Code]...
The issue is that when I type the following command, I get the further following horrible error message that doesn't seem to really point me to anywhere and I can't seem to find any relevant information to my problem on the web:
root@darkstacks:~# qemu-system-i386 -hda test.img -m 128 -curses -net nic -net tap,ifname=tap0 warning: could not configure /dev/net/tun: no virtual network emulation
Does anyone have any idea what I need to do here? My processor does not have the vmx flag, as it's a 2.4GHz P4. I don't know if that might have something to do with it.
I have vnc4server installed and I can get it to work on a desktop by desktop basis, but I can't figure out how to get it to run on startup. There isn't a script for vnc in /etc/init.d/ How do I go about creating one? Is there a better way to solve this problem?
View 4 Replies View RelatedI tried recompiling a new kernel yesterday (2.6.34) on my debian sarge box, but I ran into multiple difficulties. These difficulties forced me to do a double dist-upgrade to lenny. The new kernel was (seemingly) compiled without any hiccups, and I ran dpkg -i on both the image and the header debs. They didn't install properly into grub, but I think I managed to fix that manually.Next thing I did was rebooting the server. It refused to come back up. Luckily my ISP has recovery tools, so I managed to switch back to the old kernel. It boots just fine with that kernel, but the problem is that there is no ssh daemon running! I can access it through ftp and do limited jobs through php, but nothing big, as I have no root access.Now, enough backstory. My question is: How can I install openssh-server onto the server remotely? I cannot access the server personally, as the server is in a completely different country.
View 14 Replies View RelatedI've been trying to setup Plymouth on Debian Squeeze, but have only been partially successful: Plymouth works with shutdown (i.e. I see Plymouth after I tell the computer to shut down), but not when I start up my computer (before it reaches GDM). In other words, Plymouth seems to work with my graphics, but for some reason does not show up at startup (not even briefly, as far as I can tell). I've searched the forums and followed this advice, as well as the instructions found here: [URL] but neither of those worked. I'm running Debian Testing (Squeeze) on a Thinkpad X41, which uses "Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller" for graphics.
View 4 Replies View RelatedI've been using Debian since the early days of Lenny being testing as OS on the same Computer. Its a Acer Aspire Notebook with switches for wireless and bluetooth. While booting Lenny my wireless and bluetooth stayed off as long as I didn't switch them on. But since squeeze they get activated ( you can see it by looking at the LED's ) the moment after the grub screen. I now do have to turn bluetooth and wireless off by hand everytime which is quite annoying since I mostly use eth0.
how to disable bluetooth and wireless per default in a way I can simply turn them back on by using the switch?
how can i setup ddclient at startup i already configured the client all i need is to let it start on bootup
View 3 Replies View Relatedwhen my computer starts up (from boot, reboot, hibernate or sleep) the speakers give out an annoying "boom".I an using Debian testing (wheezy kernel 2.6.32-5-amd64), with a Dell XPS L701. Alsa is version 1.0.23, and sound is working fine, other than this little annoyance.
View 6 Replies View RelatedThe "System Settings/Startup Programs" window is large enough but the "Program" column is too narrow and it cannot be resized. The window can be dragged to make it larger but not the individual columns. It looks like a Java listbox with "Enabled = false" set. This occurs in Debian8 64 bit and also in Mint 17 and Mint LMDE2. I am surprised nobody else has raised the issue. I have a basic setup with 22" screen and 1680 x 1050 resolution. It occurs with Nouveau and NVidia drivers. It is not a critical bug so I have coped with it for 2 years but it would be nice to see it fixed. Unfortunately I could not upload a screen shot as "board attachment quota has been reached".
View 2 Replies View RelatedMy wireless in fresh Squeeze install would not connect automatically. I have to click on the network manager and enter the root password to connect every time I start up. I have "Enable Networking" and "Enable Wireless" checked in the Network Manager.
System>Preferences>StartupApplications>NetworkManager --- checked
NetworkManager>NetworkConnections>Wireless>[mywifinetwork]Edit>AutomaticallyConnect --- checked
There are only 2 lines now in /etc/network/interfacesauto loiface lo inet loopbackWhat should I do to get the NM to look for and connect wireless automatically at start up
I have a script that needs to start executing on startup. Because I originally wrote it for MacOSX I never cared to learn how to daemonize it (thanks launchd!). Are there any relatively easy ways to run it on startup on debian to?
View 2 Replies View RelatedWe have setup squeeze workstations with gnome, citrix receiver and vmware-view client. Which startup programs and daemons, for example avahi-daemon can be normally disabled or what is disabled on your workstations?
View 1 Replies View RelatedI got a problem with a Dell Latitude E5500. I can not disable the hardware beep after the gdm3 login screen has been loaded. All alsa beeps and system sounds are disabled and/or muted. I also tried setterm -blength 0, xset -b in startup scripts. They disable terminal-beeps, but not the halt or the gdm login beep. I tried wasting around with the gconftool, but nothing happened. It is an annoying sound. If you use, init 0 to shut down, no beep comes up.
View 10 Replies View RelatedHowto configure /boot/grub/menu.lst from Lenny to hide boot text messages during the startup?
View 14 Replies View RelatedI have to use pppoe because my ISP uses service names, and as far as I know the only program which lets me input a service name is pppoe (inside the pppoe.conf file). Networkmanager is buggy because it tends to disappear from the panel periodically and, worse, it doesn't reconnect (although the option is selected, it does reconnect only once).
So, for peace of mind I open a superuser terminal and enter "pppoe-start" and "pppoe-stop" to have everything I want (reconnects automatically, etc.). Now the question is: how can I have pppoe-start run at startup, automatically, without entering superuser mode, and without having a terminal open for this? Using Debian Testing (Wheezy).
I upgraded my main PC's Xfce 4.6 to Xfce 4.8 this morning.Now, every time I start Thunar for the first time after a new boot, it takes about 30 seconds to appear, and then about 10 seconds later, a second instance of it appears.After that, Thunar appears instantly every time I start it during that same session. But if I shut-down or restart my PC, Thunar again takes about 30 seconds to start up, and a second instance of it appears about 10 seconds later.
Google searches seem to indicate that people running other distros are also experiencing this problem. On advice in a different forum, I deleted the ~/.config/Thunar folder and restarted my PC, but that didn't help -- it created a new Thunar folder, but the long delay and the double-Thunars are still there every time I run Thunar for the first time in a session.
My plex media server does not work with systemd apparently but running the command below makes plex startup properly
Code: Select all/usr/sbin/start_pms &
Is there anyway to make this command run on my computer at startup.
I am running debian 8 jessie.
That the Linux bridge configuration does not work afer I upgraded the kernel to 2.6.33.2. Why I can't find the device vmbr0?
[Code]...
I want to set up a bridge using bridge-utils within /etc/network/interfaces like is shown here in this guide: [URL] The problem is that, at the same time, I want eth0 to have a specific static IP address. Right now I have a configuration for eth0. This guide tells me that I should not configure eth0 outside of the br0 configuration.
View 3 Replies View RelatedI wonder what is your opinion about the best method for using an ADSL modem. Router or bridge? I did read some articles that say "that the bridge mode gives you more stability and has higher speed". Is that true?
Furthermore, you suggest any alternative to "pppoeconf"? I've been getting this errors ( in the plog), related to "PAD packet loss" and also errors in "PPPOE Discovery", even when I am connected. When this things starts to show up on the log, my connection "pauses" for some seconds. I do not feel very safe with this program.
I've successfully install kvm with private network (nat) up running. I want to switch the kvm network using bridge mode (or host-interface), but do not success. env: nic iwl4965/ kernel 2.6.27.8/ debian etch upgrade to lenny/ kvm 0.9.1/ hardware hp 6910p The doc I follow up is at [URL] The way how i set it up is to modify /etc/network/interfaces by adding following section to enable br0
Code:
allow-hotplug br0
iface br0 inet dhcp
bridge_ports wlan0
bridge_fd 9
[code]....
However, the problem is the guest os, which starts with -hda k1.img, can not access to the internet. Is there any step I miss? or it is because wireless does not support bridge (I've heard doc says that wireless does not support wireless bridge)?
I am a (somewhat) newbie to Linux (but have an extensive Windows background), and I have just installed Debian Squeeze in an old EeePc 701 4G using the netinst version only with the following packages:
eeepc-acpi-scripts
x-window-manager
gnome-session
gdm
gnome-themes
gnome-themes-extra
plymouth
bridge-utils
Now I would like to install Debian in my main laptop, but I think it won't be able to connect to any wireless networks during setup and before installing firmware-brcm80211 and wireless-tools (its wireless card is a Broadcom 43224AG). That being, and to avoid connecting the computer directly to the router (it is not easy), I would like to bridge the EeePc's wireless connection to my laptop using a cable. I tried using the instructions found at the Debian Wiki, but I couldn't set it up properly.
I'm trying to setup openVPN on debian, well this worked. But every client will get the same ip (172.17.0.6 - local it is). how to set my server in bridge mode. I've read about: server-bridge LOCALIP 255.255.0.0 172.17.1.20 172.17.1.100
BUT, my server has no ipv4 address, but only ipv6: 2001:41d0:2:b2d6::542a:74a so I am not sure how I can do this.
I am trying to set up a network like this:
Internet <---> Router <---> Debian server <---> Windows PC
I want the server and PC to both have internet access, and I want to be able to forward ports from the router to the server. I know how to configure the server to give the PC internet access, but how would I assign an IP address to the server and give it internet access? I have used a very similar setup a few years ago, but I can't remember how to do this.
I've two networks (network 1 in the apartment, network 2 in the basement/server room) I would like to build a vpn connection between the two networks. In networks 1 I have a 24h running PC/Firewall/Debian Server. For network 2 I would like to buy a RVS4000. Is it possible to connect the two objects (Debian and Cisco)?
View 2 Replies View RelatedI am trying out chrony as a replacement for openntpd as there is no longer an openntpd package in Debian Squeeze. Two questions:
1. Is there a necessity or equivalent to openntpd's "-s" option, where it forces the system's clock to the network time on daemon startup, regardless on how great the clock is off?
2. How do you configure as a client only, not as an ntp server at all? By default, it listens on UDP 123 and 323 (both ipv4 and ipv6) and definitely acts as a network time server (I can query remotely). I do not see anything obvious in the docs. Openntpd by default ran as a client daemon only.
