i have recently installed freeradius in my debian jessie. i want to configure it to act as radius to my home router to authenticate wifi users. i want to use EAP-PWD auth medthod but there is no such section found in eap.conf.does any body know's how to configure EAP-PWD??
View 1 RepliesI've got a task: make time server, that gets time from gps, shows it on display and send to different systems through different ports like com, ltp, etc.
Solution is qt program, included in hybrid iso image.
I've created my binary-hybrid.iso debian, added my program and installed it on pc sudo dd if=/media/cdrom/binary-hybrid.iso of=/dev/sda then i restarted and everything is ok, but...
I also need:
1) to make my pc works as ntp-server, to do this i must change file ntp.conf in ntp****.deb before i build my iso
how can i do this?
as i realized according to live.debian.net/manual it's possible to do by putting smth to /live-build/config/packages.chroot and by adding some parameters to lb config but i can't find how and what
2) to save my program parameters after reboot. for example, i have such parameter as gmt. it defined as +3. i can change it while program is running to -5 for example and i want to have gmt -5 when i next time turn on my computer
When in programming it is simple - program creates ini file in it's directory and read/write parameters from this ini-file, but how to make possible to do the same thing when it works from iso?
I am using Debian testing. If I install the gnome-desktop-environment then the sound driver defaults to HDA but since I just installed gnome-core (for a more stripped-down version of gnome) the default is the OSS driver. How do I get ALSA to default to the sound driver HDA?
View 1 Replies View RelatedI saw rsyslog is now installed in Debian Lenny instead of syslog. I want to send local iptables log to remote server. I modified the file config /etc/rsyslog.conf like this :
# provides UDP syslog reception
$ModLoad imudp
$UDPServerRun 514
[code]...
I have a Debian server that had only one onboard NIC (1000 Gbps) but now I've added two PCI Intel Pro 1000 NIC's into the system to bump up the total # of NIC's to three. My question now is can I specifically assign or force Debian which interface to configure as ethx? I would always like my onboard NIC to be 'eth0' and the two additional NIC's to be 'eth1' and 'eth2'. For some reason Debian loads the modules at random and sometimes what was my
View 2 Replies View RelatedI have been trying to configure an MTA (sendmail) on a new Debian installation to receive system messages and local network mail. I have no need to fetch or relay mail outside my teeny LAN. The logs on the sending machine told me the mails were refused by the receiving (Debian Lenny) system. So I ran some quick nmap scans. From the sending machine, scanning the Debian machine:
PORT STATE SERVICE
22/tcp open ssh
111/tcp open rpcbind
From the Debian machine, running 'nmap localhost':
PORT STATE SERVICE
22/tcp open ssh
25/tcp open smtp
111/tcp open rpcbind
587/tcp open submission
From the Debian machine, running 'nmap debian' (this is a virtual machine named debian) :
PORT STATE SERVICE
22/tcp open ssh
111/tcp open rpcbind
Why the two different results? How do I get the scans to be the same so I can, eventually, configure an MTA?
I've been trying to configure Postgresql in Debian for some time now, in order to install a ERP program in my computer, but when trying to follow the tutorial for the program configuration I end up stalled. Basically its says this:
1) under su, start by finding the postgresql.conf file (it points the location of the file in /var/lib/postgres/data, but it isn't there) and find the line saying 'tcpip_socket' and changing it to "true"
After a little search and help, I found this file in /etc/postgresql/<version>/main/ but the mentioned line is absent, locate it or tell me where to add it in the file? I've read the file front to back and I'm pretty sure the line isn't there.This is, according to the tutorial, to enable the server to connect to a Java program through the JDBC.
2) after editing postgresql.conf, edit pg_hba.conf and add the following line to the end of the file: host all all 127.0.0.1 255.255.255.255 trust
I get stuck after this, because I'm now supposed to restart the server by using '/etc/init.d/postgresql restart', but bash replies that the path is invalid. The program I'm trying to install is hosted here: [URL]. It's a portuguese ERP program.
To exploit the guessnet capability, I have configured my WIFI so that ifplugd can auto connect WIFI after boot.The access point is hidden, and I have provided all the required info in my /etc/network/interfaces file
mapping wlan0
script guessnet-ifupdown
map default: office-wifi
[code]....
After updating my squeeze laptop today I noticed that grub from a few days back fails to --configure.
The dpkg log says
2010-09-09 18:52:45 startup packages configure
2010-09-09 18:52:45 configure grub-pc 1.98+20100804-4 1.98+20100804-4
[code]....
how to configure my firestarter firewall. I have a website which requires the port 1935 to be open. I figured out how to open the port using firestarter. Is there anyway to make the port open only to this website, and not to every other website for security reasons of course.
View 4 Replies View RelatedI've created Live Debian USB image and it works well, but if I put an additional USB stick, then it's just read only. Howto configure Live Debian before rebuild an image to get fully USB support, i mean to write into other USB drives?
View 4 Replies View RelatedSetup a DNS/DHCP/Directory server on Debian? I would like to configure the things in Debian so that can join Linux and Windows(if possible as m not sure yet) clients to the directory server. Any links to setup both Forward and Reverse lookup zone in the environment.
View 4 Replies View RelatedI will see ipcam in my local network from my tablets. I'm install server/client but I can't even ping my Ipcam from my tablet.I'm ping my ipcam from my server
Code: Select allping 10.42.0.22
PING 10.42.0.22 (10.42.0.22) 56(84) bytes of data.
64 bytes from 10.42.0.22: icmp_seq=1 ttl=64 time=0.639 ms
eth1:1 Link encap:Ethernet HWaddr 00:25:22:1c:6e:05
inet addr:10.42.0.1 Bcast:10.42.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
inet addr:10.42.0.1 P-t-P:10.42.0.2 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:1775 errors:0 dropped:0 overruns:0 frame:0
[code]...
my tablet can receive ip, can see ftp on server but can't see anything in my home network.
I have just set up the above OS, however, installation did not find my network and therefore APT additional software & security updates could not be accessed.The network was simple to setup post installation.I have uncommented a few sources in the sources list file but obviously that does not,in itself, suffice to get accessability. I am also unable to configure my supported HP printer and I assume that can only be done with an additional package via APT.
View 6 Replies View RelatedI have just installed Debian Squeeze on my spare computer (dual booted with Ubuntu 11.04) and I cannot connect to the internet using Squeeze. Due to my ISP, I have to manually connect this computer and on Ubuntu copying and pasting a text file such as this into the terminal works with no problems.What do I need to do to manually configure my Squeeze internet connection?
View 5 Replies View RelatedTrying to install and configure a webserver - With Postfix, Courier, MySQL And Squirrelmail. But I am stuck. Postfix mail system is not running. It seems to execute /etc/init.d/postfix start, but it really did not. reload; fatal: the Postfix mail system is not running. And in mail.log is that:
Master.cf: line 40: bad transport type: smtp_data_d$_done_timeout=1200
I am trying to configure samba for a stripped down file server. I am running debian with command line only. My problem is that I cannot unmask samba.
See below:
root@debian:/home/aaron# service samba status
● samba.service
Loaded: masked (/dev/null)
Active: inactive (dead)
I have tried "sudo systemctl unmask samba.service". I receive no errors however it does not actually unmask. I can't find anything online regarding a service stuck on masked status.
I have an Acer Aspire V15 Nitro Black edition, and I recently installed after working so hard Debian 8.2
My problem is that I can't see any WiFi connection...
I believe that the firmware for my card is the ath10k, but I can't install it...
lspci -nn | grep Network
07:00.0 Network controller [0280]: Qualcomm Atheros Device [168c:003e] (rev 20)
for some reason I got taping on touchpad is disabled after some software upgrade or something.I can enable it with synclient TapButton1=1, etc.. but have got to do it every time I reboot. Also, I don't have Xorg.conf file. Is there any way I can configure taping to work permanently ?
View 6 Replies View Relatedbut I have been literally banging my head against the wall.I am trying to configure skype on my system (testing, x86) but unsuccessfully.Let me say that I am now using skype (static) as downloaded from skype website.
$ lspci
00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 04)
[code]....
I've recently been trying to restore a Debian installation back to it's previous state after a serious operation system crash. Efforts are largely going well however I've run into problems since reinstalling Wine. Previously I could execute a Windows executable by simply entering ./executable.exe in the bash shell but this no longer seems to work as now I have to include the "wine" command in front of the executable. how to configure Debian to automatically use Wine to execute using the ./executable.exe format?
View 1 Replies View RelatedKernel: Linux 2.6.26-2-686 (i686)
Compiled: #1 SMP Thu Nov 25 01:53:57 UTC 2010
C Library: GNU C Library version 2.7 (stable)
Distribution: Debian GNU/Linux 5.0.8
Desktop Environment: GNOME 2.20
Gnome comes with Vino Remote Desktop as part of it's package. I want Vino to run at boot so that I can login remotely.I am using VNC-4.1.3 for remote viewing. However, I can only view remotely once I have logged-in locally
I have got the following Problem: I installed the 64 bit lxde Debian version... I couldnt configure the network during the installation because I just have a dsl modem and not a router... so the configuration of the network failed.... after the installation I started debian... and was surprised about the lack of "basic system configuration"-software that had been installed... I couldnt find aptitude or whats the debian-Update-Programm called .... instead I found OpenOffice... HAE? then I tried to configure internet access..... so I started a terminal and tried to start pppoeconf... but the program wasnt found! ARRRGG! What am I doing wrong here.... Why are these system utilities like pppoeconf not always installed...
View 1 Replies View RelatedI'm using debian 5 x64 with xfce.Is there a way to configure (start/stop/restart) services (especially Apache2, mySQL and PHP) using a graphical or cli tool? I tried to use sysv-rc, sysv-rc-conf, rcconf and rc-conf in the terminal but Bash didn't find them (Although Synaptic show that sysv-rc is installed).
View 9 Replies View RelatedKernel: Linux 2.6.26-2-686 (i686)
Compiled: #1 SMP Thu Nov 25 01:53:57 UTC 2010
C Library: GNU C Library version 2.7 (stable)
Distribution: Debian GNU/Linux 5.0.8
Desktop Environment: GNOME 2.20
Gnome comes with Vino Remote Desktop as part of it's package. I want Vino to run at boot so that I can login remotely. I am using VNC-4.1.3 for remote viewing. However, I can only view remotely once I have logged-in locally.
I will be relocating to a permanent residence sometime in the next year or two. I've recently begun thinking about the best way to implement a home-based network. It occurred to me that the most elegant solution might be the use of VM technology to eliminate as much hardware and wiring as possible.My thinking is this: Install a multi-core system and configure it to run several VMs, one each for a firewall, a caching proxy server, a mail server, a web server. Additionally, I would like to run 2-4 VMs as remote (RDP)workstations, using diskless workstations to boot the VMs over powerline ethernet.The latest powerline technology (available later this year) will allow multiple devices on a residential circuit operating at near gigabit speed, just like legacy wired networks.
In theory, the above would allow me to consolidate everything but the disklessworkstations on a single server and eliminate all wired (and wireless) connections except the broadband connection to the Internet and the cabling to the nearest power outlets. It appears technically possible, but I'm not sure about the various virtual connections among VMs. In theory, each VM should be able to communicate with the other as if it was on the same network via the server data bus, but what about setting up firewall zones? Any internal I/O bandwidth bottlenecks? Any other potential "gotchas", caveats, issues? (Other than the obvious requirement of having enough CPU and RAM).Any thoughts or observations welcome, especially if they are from real world experience in a VM environment. BTW--in case you're wondering why I'm posting here, it's because I run Debian on all my workstations/servers (running VirtualBox as a VM for Windows XP on one workstation).
When i want to configure my touchpad on my dell inspiron 1525 with debian lenny then i got this message: gsynaptics couldnt initialize you have to set 'shmconfig' 'true' in xorg.conf or xf86config to use gsynaptics My touchpad is an alps and not a synaptics so far i can see. My xorg.conf is this: [URL]
View 13 Replies View RelatedI am currently trying to configure a set of hard drives as a RAID configuration. My system is running with Red Hat Enterprise Linux Client release 5.1 as the base OS. I am booting from CD. I am trying to image a set of drives that have not been imaged before. When the GUI dialog window for disk setup is displayed, it shows a default disk layout including a LVM slice. In the disk layout is a /boot partition already. It is not what I would like so I edit it to be the size for my system and make it the primary partition. I also select it to be a software RAID. I then add three more partitions for my drive 'A' all of type software RAID and NOT primary partitions.
At this point my drives have the correct number of partitions except for showing the LVM slice. I select 'RAID' again, followed by selecting 'Clone a drive to create a RAID device ...' followed by 'OK'. I then get a dialog to select the source and target. i select my drive 'A' to be the source and 'B' to be the target followed by 'OK'. An error dialog is received stating that all the partitions are not of type software RAID. The disk partitions are all type software RAID except the extended LVM slice. I can not get past this point and I am following a procedure written some time ago by a person that is not available.
I am having no luck configuring ProFTPd on a Debian Lenny production server we use to host our MySQL databases and a few websites. I had originally set it up so I could login and manage our internal sites, but I have the need to allow a few clients in to access their sites that we host. I am trying to root the users in their site directory, which would be "/sites/www.whatever.com/".
It just hit me while typing this. Is it possible to create a user without a shell to prevent login via SSH and set the home folder to /sites/whatever instead of /home/username? That would allow me to continue operating with my current configuration and root them in their site while preventing SSH logins.
i have a HP MSA 2312fc SAN with 2 LUNs configured. The first LUN (LUN ID 1) is correctly connected to the system, but when i connect the second LUN (LUN ID 30), i find in the syslog this message: multipathd: 8:64: size 6835937472, expected 5267578112. Discard
Here is the multipath.conf
[Code]....
So I correctly see the two luns, but multipath doesn't create the relative devices. Under /dev/mapper I see: control mpath0 mpath0-part1 mpath0-part1 is the first lun, the one I mounted in a directory under filesystem. I can't find the device for the second lun