I need to connect to a serial port server via /dev/tty.. . The serial port IP addresses are the server's IP address with a particular port # (10001, 10002 etc). The way this seems to work is to create a pseudo-tty and somehow link or configure it to point to the serial server's IP/port #'s.
View 3 Repliesi want if a port (exp. 1001) have 20 connections that the next new connection forword to an other port (exp. 1002).
View 2 Replies View RelatedI am using Squeeze and all appears OK at first... I have a DHCP lease, PING to router works, apache servering fine in and outside the network, Epiphany seems to connects to default debian.org only, BUT I cannot connect to any other websites and apt will not connect to any servers. I installed once, tried to fix problem, gave up and reinstalled and still have the same problem.
I unistalled Network Manager thinking that was the problem, but still the same issue. Is there a default firewall blocking certain connections or am I missing something I'm supposed to know about? I installed some non-free firmware in the beginning of install and all worked... and I connected fine when downloading packages during install.
On this moment i build an webenvironment with wordpress, apache2, debian 8. On this moment i try to impelement Varnish.
By default this application use the port 6081. I try to put apache on port 8080. This already works but i get varnish not running on port 80.
You can see below that varnish still listen to the default port 6081. How can i fix this?
Code: Select allroot@webI:/home/beheerder# netstat -lpt
Active Internet connections (only servers)
Proto Recv-Q Send-Q Local Address      Foreign Address     State    PID/Program name
tcp    0   0 *:ssh          *:*           LISTEN   2917/sshd
tcp    0   0 *:6081         *:*           LISTEN   3717/varnishd
tcp    0   0 localhost:6082     *:*           LISTEN   3699/varnishd
[Code] ....
To test another port i have also try to start Varnish on port 85.
Code: Select allvim /etc/default/varnish
DAEMON_OPTS="-a :85
       -T localhost:6082
       -f /etc/varnish/default.vcl
       -S /etc/varnish/secret
       -s malloc,256m"
I have restart the apache and varnish services. I have also rebooted the server but varnish will not listen on port 80 (or other non default ports). On port 6081 the application works fine. But how can i fix this ?
Source Varnish port 80
I can use the application with the following command
Code: Select allvarnishd -f /etc/varnish/default.vcl -a 0.0.0.0:80.
But why is this not working with the normal config file. Varnish are than listen to port 80. With every server reboot i need than to run this command. So i would like to use the config file.
Is is possible, via iptables or something similar, to bind a service running on a specific port to a specific interface? My case: I use a VPN service for privacy. I would like to have all traffic except ftp and ssh to run over tun0. Ports 21 and 22 will need to be accessible to the outside world (eth0) while the VPN is running.
View 3 Replies View RelatedI'm trying to setup VNC on our debian server so the boss can remotely do admin stuff from anywhere in the world. the first step is getting it working from anywhere in the room, though. And I can't even seem to get that far.
So far I have a VNC server setup, although not without problems. I downloaded and installed vnc from the vnc site, that wouldn't work because trying to start a vnc server gave this error: "error while loading shared libraries: libstdc++-libc6.2-2.so.3: cannot open shared object file: No such file or directory"
There are lots of results on google for this error, and the solution everywhere seems to be the same. to install the package: libstdc++2.10-glibc2.2
However, trying to install this package in debian fails. both using apt-get and trying to manually download it from packages.debian.org it just doesn't seem to exist.
I've tried tightvnc from the official repositories and it gives the same error, too.
The way I got around that eventually, thanks to another tutorial, was to install the package vnc4server. then run vnc4passwd to create a password. and after that vncserver works fine, or seems to. Creates display 1.
Now, when I'm trying to connect to hostname:1 from another computer in the LAN. It gives error 10061, connection refused. I installed the debian and I don't recall setting it up to refuse connections on port 1. Is there anything I should check or change to allow the connection, or any log file in debian to check and see what's going wrong?
I'm also trying connecting internally via client on the debian machine, but I can't runvncviewer. I get the same missing shared library error as before. I guess I just worked around, not solved it.
I also can't access it with the java viewer. Trying to connect on port 5801 either from the server itself, or from another one on the lan, tells me it's refusing the connection.
To be clear, I'm certain that the vnc server is started. We have working DNS, and trying to connect directly to the internal IP:1 doesn't work either.
I just noticed after installing a new server with samba that a portscan will show the samba used ports. This server has two interfaces, a world address eth0 and an intranet eth1. The samba ports show in scanning either interface, even after I changed samba to listen only to the intranet (192.168.x) address.
I am concerned especially about the 139 and 445 ports, which could attract a lot of garbage traffic.This is Debian 5.05 default samba installation.Otherwise similarly installed Ubuntu box with two interfaces does not show samba at all, even though smbd is running and working just fine.
Everything default.Everything works nicely with one exception. I can't connect to MySQL from the network.nmapping localhost tells me 3306 is open but nmap from the outside shows only ports 22 and 111 open. To my knowledge I have no firewall, iptables -L gives an empty set.I have several similar installations on the same network without any problems of this nature.
View 2 Replies View RelatedI've setup my own repository which I want to use SSH as the protocol. I managed to get everything working with an SSH key using port 22. Now, I would like to change the SSH port. I've already changed it on the SSH/repo server. Now I can't figure out how to change apt to use a custom port on the client computer.
My sources.list file line which worked over port 22: deb ssh://user@1.1.1.1/home/user/repo lenny main contrib non-free I've tried: deb ssh://user@1.1.1.1:12345/home/user/repo lenny main contrib non-free and it fails and actually says "failed connecting to port 22"
Can this be done? I've searched google for hours and I getting nothing but unrelated data. I've read the man pages. The man page for apt.conf specified that you can set the port this way for HTTP, but doesn't mention anything about ssh ports.
I'm trying to get https/443 traffic go through squid.
View 3 Replies View RelatedI have a java application that I wrote recently. It runs off port 9955. The application runs great on my mac server. When I installed it on my linux box i cant get to it from outside the box. A port scan shows the port as closed. I flushed my iptables, did not help. I can telnet into the app locally, from the server and it works great. I cannot telnet from outside the server. I have a reference to the application in /etc/services as a tcp port (which it is).
netstat shows it as listening
netstat --listen
tcp6 0 0 [::]: SimpleSocketTest [::]:* LISTEN
netstat -anp | grep 9955
tcp6 0 0 ::: 9955 :::* LISTEN 1484/java
I have got a laptop running Debian squeeze. I wish to share the wireless connection of the laptop (wlan0) to the ethernet port of the laptop, so that I can share the wireless connection to my desktop PC which is connected to the ethernet port.
[My desktop PC]---Ethernet---[My laptop]---))) WiFi )))---[Public network/ ISP]
I have read the article on Ubuntu community: [url]
I followed the steps, and the /etc/network/interfaces file on my laptop is:
Now the situation is: My laptop can connect to Internet (i.e. ping debian.org from laptop is fine), my desktop PC can connect to my laptop (i.e. ping 192.168.1.1 from desktop PC is fine). However, the desktop PC cannot reach the Internet.
I also read the information on Debian Wiki: [url]
It seems I must install and configure ebtables before sharing my wireless connection to ethernet port. Is it true? (But why the article on Ubuntu community doesn't mention it?) Or I just made some mistakes?
I have a trayless SATA hotswap bay that is really terrific for quickly attaching and removing SATA hard drives. I'm trying to write a udev rule to create a symbolic link to the device node for the drive that is attached through the hotswap bay (/dev/bay -> /dev/sdX). This eliminates any ambiguity when performing destructive tasks (fdisk, etc). I'm running squeeze amd64. I've read through several tutorials and have it working somewhat. Here's the output of udevadm info for a drive attached via the hotswap bay.
looking at device '/devices/pci0000:00/0000:00:11.0/host7/target7:0:0/7:0:0:0/block/sdb':
KERNEL=="sdb"
SUBSYSTEM=="block"
DRIVER==""
ATTR{range}=="16"
ATTR{ext_range}=="256"
ATTR{removable}=="0"
ATTR{ro}=="0"
ATTR{size}=="156301488"
ATTR{alignment_offset}=="0"
ATTR{capability}=="52" ....
Here is my udev rule
DEVPATH=="/devices/pci0000:00/0000:00:11.0/host7/*", SUBSYSTEM=="block", SYMLINK+="bay%n"
This produces the desired behavior and gives me an fdisk-able device node. The problem I am having is that the "host" component of the DEVPATH varies from bootup to bootup. I'm just using on onboard SATA, host2-7, specifically host7. There is also onboard PATA, host0-1. It seems to just be random which "host"s are assigned to which controller. For example, the next time I boot the system, the onboard SATA will be host0-5 and the onboard PATA will be host6-7. In this simple case, I could just write 2 rules, one for each possibility and it would still be correct because of the different PCI addresses of the two controllers. But on systems with more SCSI (uh... libata, actually) controllers, a "host" file can point to different physical ports between bootstraps. This would be bad. Does anyone know of a way to write a rule to tie a device node to a specific physical SATA port on the motherboard/hba?
I've got a server listening on a port. when I stop the server the port stays open for some minutes. How can I close it immediately?
View 2 Replies View RelatedI did a netinstall earlier today (latest version, amd64) on my Dell XPS laptop and ended up with a minimal installation because I couldn't connect to the internet. Now I'm trying to get online without a desktop environment.
I have an Intel Centrino 1030, so I downloaded and installed the firmware [URL].... with a usb, then rebooted. My searches have turned up a lot of instructions involving a utility called iwconfig and wpasuppliant, but these are apparently not installed. I don't really know much about it, but my /etc/network/interfaces file looks rather empty:
Code: Select all# The loopback interface
 auto lo
 iface lo inet loopback
Shouldn't there be something like wlan0 there? The network card does show up with lspci
I have been using another OS but thought for Ham Radio Debian might be good however my stupidity took over right at the start.Have a live cd and works fine but I don't know how to connect to the Internet.Using DSL.
View 9 Replies View RelatedI installed testing on my netbook with cd1. and too my suprise it didn't even include something as important as network manager. all i want to do is connect to my wired internet, install network manager, then install my driver for card. if i can just get wired working i will be homefree. the directions for installing my wire3less driver look super simple.
View 4 Replies View RelatedI am trying to connect to a Debian account through SMB. So far I havn't had any luck and from what I have read online, without Windows 7 registry modifications, I won't get anywhere either. I have tried two main configurations on in the smb.conf. The first method was to use 'security = share' and submit the username and password on the created share. That didn't work. The second method was to use 'security = user' and authenticate to the entire smb server. That didn't work either.
I am unsure what username/password I have to enter. I am using the accounts credentials, but it isn't letting me connect with those. It also wants me to use a domain (something like 'LAPTOPusername' and then password) which I don't understand the relevance. What domain should I use?
When it comes down to it I just want an SMB share that all the Windows 7 computers in my house can access, but still requires a password. Are there any guides available? Please make sure they are up to date with the latest SAMBA and Windows 7 configuration. The ones I have gone over are old and didn't fix my problem. Also if I need to modify the registry then it isn't worth it.
I installed a fresh Debian Desktop without the LAN cable connected. After that I got message when I put the cable in:
Code: Select allNetwork Interface
Connection New Wired Connection failed
I have tried to re-install everything once again with the cable in, but during the Debian installation there was no network detected.
However, I proceeded and re-installed Debian. But the problem persists. It continues to re-connect and than disconnect. There is a symbol showing re-connection. The network eth0 is visible to the machine.
I booted Mint Live disc and the same happens there.
Recently after updating my Debian Jessie, I can no longer access windows shares. I can access those shares from windows PC. And to be able from debian.
After I enter my password of windows share, the password dialog box pops up again. No warning, no errors. It just pops up. I cannot connect to any windows share.
I have Debian 8 with VBoxGuestAdditions (4.3.18). I can connect to this box from Win7 using RDP (mstsc.exe). When I connect from Windows 10 using mstsc.exe I've got error code 2308. I tried NoMachine, 2XClient, RoyalTS none worked.
W10 connecting with RDP to Linux server? If I would install xrdp onto the Linux server would it work for me?
Is it possible to connect from Win10 to Linux using RDP?
Finally took the plunge and decided to give debian a go, not done so before as feared it would be too complicated. Net install went ok. Used to wiki to get me wireless up and running by copying those commands provided most of which made no sense (why the separate kernel image for wireless?).
Anyway seems to have worked so now to the problem I can't connect to my wireless network its not broadcasting so configured it manually the way I do in ubuntu through the net manager, it doesn't connect at all.
I set up a vpnc connection, and it says it connects fine, but then I have no internet connection at all, and cannot ssh into the remote server(the reason i need this vpn) or do anything else involving the internet.I question if it actually connects at all, as sudo vpnc myconf.conf only shows the connect banner and never progresses from there.
View 4 Replies View RelatedTwo nights ago I decided to switch from testing to unstable. Since then I am able to connect to the internet, but not to anything on my local network. I am unable to ping this computer from another one on the network. This computer is connected through wireless. I thought that something might have changed with iptables that was blockinghe localnetwork. I tried to "flush the iptables settings with "iptables -F". Since that didn't work I uninstalled iptables (which didn't work and I reinstalled iptables). In my browser I tried to connect to my router and that doesn't work either.I connect to this computer daily through ssh and connect to a NAS. Without ssh and my NAS I feel kinda lost
View 6 Replies View RelatedI am attempting to get my laptop wireless to connect to my router. Wicd sees my router, I enter the known good password, and it reports bad password. Configuring router without wireless security and attempting to connect with wicd without security fails also. Laptop wireless has worked with other another linux distro, and windows.
Environment:Squeeze installed to Dell laptop with wireless: Bus 003 Device 002: ID 0a5c:4500 Broadcom Corp. BCM2046B1 USB 2.0 Hub (part of BCM2046 Bluetooth)
Wicd reports that it fails with this text:
2011/01/11 20:06:02 :: Putting interface down
2011/01/11 20:06:02 :: Releasing DHCP leases...
2011/01/11 20:06:02 :: attempting to set hostname with dhclient
2011/01/11 20:06:02 :: using dhcpcd or another supported client may work better
[code]....
My sid machine currently can't access debian.org, through apt hitting the repositories, surfing through Epiphany or Iceweasel, or pinging the server directly. It was working fine until about four days ago. However, if I type in the IP address, I can access the website, so it must be some sort of DNS issue. My home server, running Squeeze, can access debian.org just fine. Any suggestions for how to fix it?
View 1 Replies View RelatedI have a laptop (running Arch Linux) and a desktop. Until recently my desktop computer ran Arch but I'm taking Debian for a spin now. At my home there is a wireless network with WPA2 encoding. I use the wicd gui to connect to this. I assume, that since I can see the SSID in the wicd window, all drivers are correctly installed and functioning. On my Arch computer, wicd reports this SSID as having WPA2 encoding, but on the Debian computer, it shows up as WEP. Even when I choose the correct encryption thing, WPA2 (preshared key), and put the correct password in, I can't get a connection up.
View 6 Replies View RelatedI've been having a problem with Bluetooth on Debian 8 Jessie i just can't connect to any bluetooth device, i have only tested my smartphone and my bluetooth headphones, i am using blueman manager.After attempting to connect to my bluetooth headphones/smartphone it just disconnects and says "Connection Failed: No such file or directory",i don't know if i have to create a config file or something, the error message doesn't say anything but the error previously mentioned.
View 7 Replies View RelatedSince a recent update on Stretch, I have been unable to use the network-manager to connect to my home wireless network on my laptop. It was working fine before. I did not change any settings on the WLAN router. I can still connect to other wireless networks at work and university, just not this particular one at home. All other non-Debian devices in my household are still able to connect just fine.While figuring this out, I have tried connecting manualy with ifup but I don't really know how that works. Right now there is only the loopback entry in /etc/network/interfaces.
Below is the output of syslog, when gnomes network-manager is trying to connect, but fails.
Code: Select allJul 19 20:01:57 debian NetworkManager[6705]: <info>Â (wlan0): Activation: starting connection 'Affenbande'
Jul 19 20:01:57 debian NetworkManager[6705]: <info>Â (wlan0): Activation: Stage 1 of 5 (Device Prepare) scheduled...
Jul 19 20:01:57 debian NetworkManager[6705]: <info>Â (wlan0): Activation: Stage 1 of 5 (Device Prepare) started...
[code]...
So I have a router that I've gotten from my ISP, which seems to run a hardened, custom version of OpenWRT. By that I mean it's read-only and has a lot of files mostly in RAM. So putting custom firmware on it is not an option for me right now, as it's by only router. Actually, it's not just a router, it's an Actiontek modem/router combo.
So anyway, lets say I have a machine on my LAN and I want to basically SSH into a box by hostname. Now the thing is, I prefer using OpenDNS (previously OpenNIC) as my DNS, and so I don't use my router as my nameserver, though I could do that.
So how do I connect to my machine by hostname? I would prefer a solution that does not use Avahi/Zeroconf or editing the hosts file. People have said setting up a local DNS server might be okay, but I'd have to do that for every machine I'd want added to my network. Kind of almost as bad as editing a static hosts file. I use really want to use DHCP over static IP assigning, and the one on my router is not as advanced, so I can't use my hosts file. And also,
So is Zeroconf the only solution? I'm not sure how to set up Zeroconf. Do you just install Avahi?
I want a simple, almost Arch-linux solution, lean and clean, using only the most minimal software. I don't care how much configuring I'd have to do, as long as it's going to stay reliable as well.