I have configured (bind) my server with multiple static IP. I can ping the main IP from outside but not the other IP . I can ping all the IP from localhost but not from the internet. I do not have any external firewall or blocking device. server is directly connected via modem. If anyone could advice me for why i cannot ping other Ip's
View 5 RepliesI have installed Centos 5 on a virtual machine (esx4i). I set it to obtain an IP address from the DHCP sever, which is a broadband router, it has been given an IP address of 10.10.11.159 the router is 10.10.11.1 but I can't ping the router and I can't get any access to the network! I have a SCO Openserver server on the same physical box and it works fine so I know the network card & cable is ok.
View 9 Replies View RelatedI posted it on another forum, but could not get response,So I have this cenOS, Ubuntu and windows operating system running on virtual machines.Now I gave them manual ip address, both ubuntu and windows machines can ping the default gateway, but not the CentOS.It should forward 0.0.0.0. to my cisco router address(192.168.5.254),
View 4 Replies View RelatedI have OpenVPN running successfully on a CentOS Linux server. All remote clients connect without a problem and can ping the server LAN (10.5.0.0/24) . The server address is
10.5.0.1. All network shares on the server are available to the remote clients via SAMBA shares and this works well.The problem is that I am unable to get the remote clients to access services on the LAN clients. For example, there is a webserver running on a Windows XP PC (on the server LAN @ 10.5.0.2) with no firewall enabled. The remote VPN clients can ping this webserver at 10.5.0.2, but cannot browse the webserver at [URL]. All clients on the server LAN can however browse the webserver. The remote clients are using Windows XP and VISTA with OpenVPN 2.1.1.
I am new to VPNs and networking, but from my research, it seems as if this may be a routing issue. I would appreciate any help you may give in getting the remote clients to access the services on the LAN clients (other than the server @ 10.5.0.1).
The server configuration is:
local 192.168.10.6
port 1194
proto tcp
[code]...
Some time yesterday, I lost the ability to ssh my remote server, or even visit any webpages it hosts.
I've explored hosts.deny, /var/log/secure and even turned iptables off to see if it would fix anything. To no avail. Here's what my ssh login attempt looks like:
Quote:
localhost ~ $ ssh -vv x.x.x.x
OpenSSH_5.2p1, OpenSSL 0.9.8l 5 Nov 2009
debug1: Reading configuration data /etc/ssh_config
debug2: ssh_connect: needpriv 0
[Code]....
So, I have an Virtual Machine running CentOS 5.4. It sits behind a hardware firewall which also does NAT'ing. I've set up plenty of these, so I know for sure the firewall and NAT rules are set up correctly. From the host, I can ping anything in my subnet and the gateway. But I can't ping anything else beyond the gateway. I can perform DNS queries and when I try to ping, it finds the appropriate IP address.But from the outside, I can ping the PUBLIC address (It's a 1 public to 1 private address NAT, not 1 public to multiple private). I've tried it with IPTABLES on and off, with no change.
View 11 Replies View RelatedI am using an virtual machine. where I need to ping from one machine to another. earlier I was able to ping. But after going to google.com once, I cannot ping back to this machine.
But if I gave ping -I eth1 <IP> then I can ping.
I cannot install any package, so tell me solution which includes not installing any package.
I have Linux server with VMware Server 1.0.8. When I creating a virtual machine, I can not "send" a PING to the virtual machine. In the virtual machine, I have installed CentOS 5.3 (32bit). In the virtual machine I have defined the addresses IP. So, whey I can't "sent" a ping to the virtual machie? I have to set something on the Linux server?
View 3 Replies View RelatedI see this site: [url]
That explain how to reboot a freeze system by remote with only make a ping in other machine.
Well I want to know if that module is compatible with my centos 5 because it appear that run in kernel 2.6.X. is compatible ?
I have 4 centos5 apache webservers all on the same network, recently, 2 of the webservers have stopped being able to ping or browse one particular website where feeds are obtained from this site. I have checked and firewall and selinux settings are disabled. The two webservers are able to ping and browse other sites. Dns settings are the same for all 4 servers. traceroute for working and not working webservers are the same.
View 1 Replies View RelatedI have two CentOS servers on the same LAN. One is CentOS 4.7 the other 5.2 They both also have a WAN interface to the same remote network. On CentOS 4.7 I can ping the remote network through the CentOS 5.2 server. i.e. ping -I eth0 remotehost On CentOS 5.2 I can NOT force the ping to go out the CentOS 4.7 server without over riding my routing tables to make eth0 a more direct route than the eth1 route.
On 5.2 If I do the ping -I eth0 remotehost, and a tcpdump on eth0, the outbound ping will not be going out eth0, he overrides it and sends it out eth1. In fact, on CentOS 4.7 if I do not have a route to the remote network through the other server (turn proxy arp off on the 5.2 machine), I will get "Destination Host Unreachable". I would ideally like to get the 5.2 machine to behave the way the 4.7 machine does.
My real life application for this is that I have a CentOS server in a location that controls access to the Internet. There is another router on the netowrk that handles traffic back to our corporate office. the CentOS server also has the ability to get to the corporate office. I ping the corporate office through eth0 to find out if the link through the other router is indeed up and active. I want to make this a CentOS 5.2 server but alas, I can not tell if the other route is up or not.
just finished installing Centos5 and I had no problems installing it. But when I tried to connect to the internet, the trouble began.My network card is installed and the status is "OK". The network card is a "Realtek RTL 8168C(P)/8111C(P)".The status of the device said "Inactive" and when I tried to activate it, it came with an error: Failed; no link present. Check Cable?Now the cable is connected as it should be.So next step I did is put in a static IP. Now the activation works fine.However I still have no internet. I can't even ping to my router!I need some new drivers for my graphics card too, but first I need the network to work, than I can download other stuff..
View 6 Replies View RelatedI am using CentOS 5.5, I installed squid3 in that machine. From my users machine i am not able to use our webmail address. Outlook shows pop3 error.cannot ping webmail address inside proxy.
View 1 Replies View RelatedI have a box at home that I've installed CentOS 5 on to. I'm new to Linux, so before connecting it up to the router I wanted to try and understand the network settings, so I connected it directly to my other PC with an RJ45 cable. From Windows 7 I can ping all known static IP addresses, but from Linux I can only ping the Linux addresses, not the Windows 7 one. Below are the TCP/IP IPv4 settings, all IPv6 settings are set to auto-assign.
Windows box (uses wireless connection for the router):
Local Ethernet Adapter
IP Address: 30.10.0.1
Subnet: 255.255.0.0
No gateway, primary/secondary DNS.
Linux box:
Three adapters:
Two onboard LAN, both configured to:
IP Address: 30.10.0.2 / 30.10.0.3
Subnet: 255.255.0.0
Gateway: 30.10.0.1
No primary/secondary DNS.
One LinkSys PCI card:
IP Address: 20.10.0.1
Subnet: 255.255.255.0
Gateway: 192.168.1.1 (my router)
Primary/Secondary DNS: my ISPs details.
The idea was to connect the box directly to the router (with RJ45) and to be able to remote login from my main PC to this one. This box is to be my home server, which I was going to put virtual machines on to for things like my development work and such.
In my office i have a network of 172.16.31.0 and a squid proxy server running, all other systems have windows XP and one system has centos. On centos system i have three lan cards and i want to test some things on it. So i assigned another IP on it of range 192.168.7.0/24 and same range on another windows system. And all the systems connected through a same network switch.
Unable to ping between Centos and Windows system. If i ping from one centos to windows system with the series of 172.16.31.0 then it replies very well but same thing is not happening in other 192.168.7.0/24 IP series.
it was not working and ping is not reply me and I add ifconfig lo 127.0.0.1 it is working and getting ping but when reboot it is lost setting how can I set it for always ping working.
PING localhost (127.0.0.1) 56(84) bytes of data.
ping: sendmsg: Operation not permitted
ping: sendmsg: Operation not permitted
ifconfig lo 127.0.0.1 later
[Code]....
now working but IWant reboot later working about same. how can I setting it boot start this .
I just downloaded and installed the latest Cent OS 5. I disabled SE linux, turned off the firewall, and selected the Server package options when installing. I plan on using this as a router/firewall between my internal network and the internet, as well as web server, etc. The first thing I did was to configure the two NICs, internal one with 192.168.7.1 address and the other with an address from my ISP (I have a static address, but I also tried to let the DSL router assign an address via DHCP). Everything looked fine, I checked /etc/resolv.conf and my routes. I was able to ping the DSL router from the server, but I was not able to do a ping or lookup on anything outside my network. I tried host, dig, nslookup, etc, no luck. Obviously then, I was not able to browse the net with firefox.
View 4 Replies View RelatedMy server was working perfectly.
My other uses on on LAN can access Internet but Cant ping the server.
Though they were able to do that earlier.
No software installed. No change in any files.
I have strange issue on Centos 5.5 server.I have static IP address (192.168.58.2) on eth1 card and can't get ping response from some sites.PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data.
[code]....
I've set a two-node cluster using Pacemaker/OpenAIS. I have only one network and if I break this one, the communication between node is interrupted ... With a ClusterIP resource, when network is breaked, then each node start the ClusterIP => 2 same IP .. Is there a way to define the prefered location of a resource when connection between these nodes is broken ?
A <==> B
If one of the node lose the network, then follow a previously written rule : start resource on A (for example). B will know than it's not the prefered node and so, will stop to serve. Possible ? This is because if both node are connected, but a problem between these node occur and client can join both node ... then the split brain is problematic ... A better solution is to add a rule when the split-brain occurs : all node wich can't reach the gateway have to stop all resources ... And so, if it's A wich lose the network, service will start on B and only B without any problem ...
I have a problem on my LAN, then: I have a laptop on which Windows Vista is installed, and every time I try to do ping to my server centos, my centos server does not respond to ping. The server is operating normally, because I found other PCs on my network that communicate normally with my centos server.
View 1 Replies View RelatedI have a box that I installed Elastix on as I'm trying my hand at Voip and Linux. I'm basically very green when it comes to Linux and the console. As I was following a guide @ engineertim.com to securing the box, it asked me to: wget [URL], But I get: Resolving engineertim.com... failed: Temporary failure in name resolution. I searched around and tried configuring resolv.conf to no resolve - :) unintended pun
I changed /etc/sysconfig/network to include GATEWAY=192.168.1.1 From the internet I have a modem-192.168.2.1, a telecom voip box-192.168.15.1, and then my router 192.168.1.1 I'm able to ping machines attached to the router but nothing beyond that. I tried to get the results for ifconfig via putty on this machine but it says command not found. I can get it when I log in at the box in question though.
I have a Lan with 100 computers with microsoft windows xp and vista on it, and I need to build a CentOS Primary domain control- PDC. So I am building a PDC , with samba 3.x +Ldap ( Light Directory Acess Protocol), with static eth0 and DHCP-server( Dynamic Host Control Protocol) on eth1.
Eth0 : 192.168.1.3
Eth1 : 192.168.1.5
Here is the configurations files:
== BEGIN uname -rmi ==
2.6.18-194.17.4.el5 x86_64 x86_64
== END uname -rmi ==
== BEGIN rpm -q centos-release ==
centos-release-5-5.el5.centos
== END rpm -q centos-release ==
== BEGIN cat /etc/redhat-release ==
CentOS release 5.5 (Final)
== END cat /etc/redhat-release ==
== BEGIN getenforce ==
Permissive
== END getenforce ==
== BEGIN rpm -q yum rpm python ==
yum-3.2.22-26.el5.centos
rpm-4.4.2.3-20.el5_5.1
python-2.4.3-27.el5
== END rpm -q yum rpm python ==
== BEGIN ifconfig -a == .....
Givens
LAN
CentOS 5.5
Windows 7 machine (hostname/NETBIOS name: AwesomePC, LAN IP: 192.168.1.20)
Workgroup: Cake
No WINS server
No Domain
No AD
Goal
From CentOS 5.5, have
# ping AwesomePC
resolve to a ping on 192.168.1.20
Problem
# ping AwesomePC
resolves to some random public IP that seems to be coming from my WAN DNS (openDNS) servers
ATTEMPTS
Have edited /etc/nsswitch.conf, edited line: hosts: files wins dns Have edited /etc/resolv.conf, added line: search CAKE Have installed samba (# yum install samba) and run (# service smb start), with /etc/samba/smb.conf, workgroup = CAKE, name resolve order = wins host lmhosts bcast
Does # ping even care about samba? How can I get this to work?
I am using centOS 5.0. After I change from DHCP to static IP address, I cannot ping hosts on the same subnet. The error message says destination host unreachable. Before I made the changes I was able to ping and now even I change it back to DHCP I still cannot ping with the same destination host unreachable message. The centOS is running on VMware on a Windows host.
ifconfig shows
eth0 Link encap:Ethernet HWaddr 00:0C29:A1:9A:10
inet addr: 192.168.0.202 Bcast:192.168.0.255 Mask: 255.255.255.0
inet6 addr ......
After pinging 192.168.0.106 (106 is on and other host can ping it), arp -a shows ? (192.168.0.106) at <incomplete> on eth0 I tried different ways by disabling the firewall and and disabling SE protection. No Luck.
I run an centos server. From the console I can ping google.com and get a reply. But when I ping another address say xyz.com, the IP address is resolved (11.22.33.44) but there is no reply. In the same network in our office from my desktop I ping [URL] and there is a reply.I turned of the firewall but still the same problem.
View 9 Replies View RelatedI have a dedicated host on my lan to monitor other hosts/services using Nagios. I'm in the process of migrating to Zabbix on that host to perform the same purpose. Both Nagios and Zabbix monitor icmp ping latency (Nagios uses ping, Zabbix uses fping) and over time the latency to other hosts grows until threshold alarms are triggered. In one week, the average latency grows from sub-millisecond to over 100 milliseconds, and continues to grow until the Nagios host is rebooted. I have verified the latency numbers using ping/fping from the command line on the Nagios host.
The problem is that pings from the monitored hosts to the Nagios host show normal latency at the time the Nagios host is showing high latency from itself to the monitored hosts. The Nagios host and monitored hosts are all connected to the same Dell 24 port gigabit switch. I already posted this question on the Zabbix forums with a graph of the latency but there were no answers. [URL] why the icmp ping latency is growing over time and how I can fix it short of rebooting the host on a schedule.
[Code]...
I have 2 ethernet cards but when I look at the Network configuration in "Hardware Tab" I have another acx wireless network. How to delete that because In my system Idon't have wireless card..probably installed before but want delete it now.
[code]...
then windows can ping server and resolve ip address and browsing Internet but can't ping [URL]... result is Request time out. ICMP already enabled in iptables.
I have multiple public ip addresses.My DSL modem blocks ping from a server behind the modem (nb6+4w) modem lan ip (gateway) is xxx.xxx.xxx.105the server is xxx.xxx.xxx.107If I DMZ this server it responds to pings.If i don't want to use DMZ, what service is ping using.I have set up virtual server 443 to this 107 ip as it's a SSL server
View 5 Replies View RelatedI am trying to get a Linux (Slackware 13.37) working in a Windows networking environment. The IT support for this organisation does not extend to Linux support, so I'm limited in what help I can get for this.
I'm trying to get to the point where I can get to the internet to download what I need on this Linux machine.
The situation is this (*fictitious addresses used) -My Linux machine uses a fixed IP address (10.100.150.21)
My Windows machine uses a DHCP assigned IP address (10.100.150.213)Both Linux and Windows machine are configured to access the gateway server (10.100.150.1)So, I can ping the Linux machine from the Windows machine and vice-versa.I can ping the gateway machine from the Windows machine.I can browse Windows Shares on the network via SMB from the Linux machine.I CANNOT ping the gateway machine from the Linux machine with the Destination Host Unreachable message being the error message.
For actual internet access I need to access a proxy server but since the Linux machine can't even ping the gateway server, it fails to ping the proxy.Now, I have been told the gateway is a HW based router and for Windows machine they use some software for authentication to connect to the network. This software isn't available for Linux, so that's why I've been told to use a fixed IP address.My experience of networking is pretty basic and most of the Linux setup is done via running Slackware's setup program.