CentOS 5 :: Install To NFS Root On DHCP Server
Aug 25, 2010
I would like to install CentOS 5 to a NFS root. My NFS server is not CentOS. Is there a way to tell Anaconda to use NFS for root? Is there a way to mount some NFS space at /mnt/sysimage and get Anaconda to use it? I supposed it should be possible to either move an already installed CentOS system to NFS and rebuild initrd with a rescue boot or it might be possible to do a manual install using rpm directly to install the packages onto some NFS space. The first would require a local disk temporarily. The latter would be an excessive bunch of tedious work.
View 3 Replies
ADVERTISEMENT
Dec 2, 2010
I'm no expert on DHCP. My problem is that i have a CentOS 5.5 server on which i want to install a DHCP server. I have two NICs where eth0 has access to the internet and where eth1 should act as an DHCP server.
I have installed dhcpd and this is how my dhcpd.conf file looks like.
Code:
ifconfig looks like this
Code:
When i start dhcpd on eth1 i get no error messages but when i connect any devices to eth1 they don't get any IP. I cant find anything in any logs about devices trying to get an IP address. I dont have any firewall rules in iptables.
View 4 Replies
View Related
Feb 9, 2010
how to configure DHCP server on centos linux and how to configure FTP server on centos linux
View 2 Replies
View Related
May 7, 2010
I have installed Centos 5 on a virtual machine (esx4i). I set it to obtain an IP address from the DHCP sever, which is a broadband router, it has been given an IP address of 10.10.11.159 the router is 10.10.11.1 but I can't ping the router and I can't get any access to the network! I have a SCO Openserver server on the same physical box and it works fine so I know the network card & cable is ok.
View 9 Replies
View Related
Nov 8, 2010
I am unable to install DHCP in Centos 5.5.
View 3 Replies
View Related
Aug 6, 2009
I am attempting to get this network card running under CentOS 5.2 but have had no luck. Some sites say to use the sk98lin driver, others the skge, which I can't find at all. I have tried multiple versions of the driver in rpm but none seem to work. The card shows under the network manager but will not get an IP address from the DHCP server.
Here are the outputs for this card.
uname -rmi
2.6.18-92.1.10.el5 x86_64 x86_64
lspci -m
04:01.0 "Ethernet controller" "D-Link System Inc" "DGE-530T Gigabit Ethernet Adapter (rev 11)" -r11 "D-Link System Inc" "DGE-530T Gigabit Ethernet Adapter (rev 11)"
lspci -n | grep "$(/sbin/lspci | awk '/net/ { print $1 }')"
04:01.0 0200: 1186:4b01 (rev 11)
lspci -vv
04:01.0 Ethernet controller: D-Link System Inc DGE-530T Gigabit Ethernet Adapter (rev 11) (rev 11)
Subsystem: D-Link System Inc DGE-530T Gigabit Ethernet Adapter (rev 11)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (5750ns min, 7750ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 121
Region 0: Memory at febfc000 (32-bit, non-prefetchable) [size=16K]
Region 1: I/O ports at e800 [size=256]
Expansion ROM at e0000000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
How to get this working as we have 3 of these cards for computers without a Gb NIC and I don't want to fight with it 3 separate times.
View 2 Replies
View Related
May 13, 2010
I'm trying to make a DHCP server work on my CentOS 5.4 box, but I have placed it on another subnet than the one that it is going to serve. I use a helper address on my router to make the the DHCP requests being routed to the DHCP server on the other subnet.
dhcpd.conf file:
ddns-update-style interim
ignore client-updates
ubnet 10.160.195.160 netmask 255.255.255.224
[code]...
View 8 Replies
View Related
Jul 27, 2010
i've installed bind and dhcp. I'd like to update dns automatically by dhcp. For the reverse-lookup-zone everything works fine. But for the forward-lookup-zone there is still the message denied. But i cannot see a mistake.
dhcp:
#
#
# DHCP Server Configuration file.
[Code]....
View 8 Replies
View Related
Jan 9, 2011
I got a CentOS server setup as a dhcp server using dnsmasq. I followed this guide more or less: [URL] So, the problem seems to be concerning the DNS server on the clients. In windows I get the "limited connectivity" icon for the network, and when I select troubleshoot it says the DNS server does not respond. Issuing 'ipconfig /all' clearly shows the IP of the CentOS machine as the DNS server, which should be correct, yes?
ETH0 is working as WAN connection and that works great.. no problem with the WAN connection at all on the CentOS machine. ETH1 has the IP 192.168.0.1 and mask 255.255.255.0 When starting eth1, it sometimes says that it can't start eth1 because the IP 192.168.0.1 is already in use.. but that is most certainly not the case. Maybe there's some kind of issue here that messes with the DNS? What's mind boggling is that it works great on a linux machine (dhcp client) and on a windows xp machine. but it does not work on the windows 7 laptop and a vista laptop and a pda device.
View 1 Replies
View Related
Mar 31, 2011
configuring DHCP server with two NICs. I need DHCP server with 2 NICs:
eth1 - 192.168.103.11
eth2 - 192.168.123.11
The client also has two NICs and suppose to receive ip addresses eth1 from 192.168.103.0 and eth2 from 192.168.123.0 Here is the dhcpd.conf from dhcp server:
ddns-update-style interim;
authoritative;
ignore client-updates;
[code]....
View 2 Replies
View Related
Dec 11, 2009
I was just wondering if someone could tell me the best method to connect all my hardwares together to achieve better result.HARDWARES.Cable ModemNETGEAR ROUTERNETGEAR FS728TS Smart switchLINUX SERVER WITH 2NICS.I want my dhcp server to serve 3VLAN networks. I need someone to show me how to do this. What do I need to do. keep in mind, I want eth0 to be used for public address only while eth1 for LAN. DHCP will be on eth0, but I need LAN on eth1 to be relayed back to eth0. This is my school project.
View 4 Replies
View Related
Aug 23, 2010
I'm new to CentOS and has recently use it.
I'm looking for a way to configure DHCP client so it would dynamically set the hostname and register itself to a DNS server. I don't have access to the DNS server.
View 6 Replies
View Related
Sep 1, 2010
I'm new to Centos 5 (and Linux) and, after installing Centos, I configured Samba, Apche, ... w/o problems (through interactive interface). My problem is tha t I need to use DHCP (all our clients use dynamic IP addresses for the ease) but I don't find dhcpd ... nor the sample config file(s).
Note : the new server I intend to use is actually connected on a LAN with an 'old' DHCP server (still under W2K server), is this the reason why I can't find/activate dhcp on my new machine ???
View 3 Replies
View Related
Oct 24, 2010
I've got a bit of a question. My network is laid out like this:
The role assignments are thus:
Firewall - sorts out the passing through to the 3 different networks, and acts as the traffic proxy.
Windows 2003 server - Does Active Directory and DNS
CentOS server - FTP and DHCP
Now, my problem is I need the CentOS server to be able to assign IP address to both networks, however, the CentOS server can *ONLY* be connected via the one interface to the firewall. It needs to assign the Windows 2003 server and the eth0 of the firewall an IP address via static DHCP, but it also needs to able to assign the clients dynamically via any address in the 10.23.1.0/24 range. I was thinking that I would be able to create static only assignments for the servers via their MAC addresses, and only have 1 dynamically assignable entry for the clients, and then get the firewall to allow ports 67 and 68 to flow freely between eth0 and eth1, but I wasn't entirely sure of the best way to do all this.
View 1 Replies
View Related
Apr 1, 2011
I had a server that I use for Radius DNS and Trying to put DHCP on it I have My pool in it seems right. I have 2 adresses aliased one being a helper IP that the router will send the request to. When I try to start the dhcp server I get the following.
Mar 31 14:33:11 rad2 dhcpd: No subnet declaration for eth0 (76.164.173.2).
Mar 31 14:33:11 rad2 dhcpd: ** Ignoring requests on eth0. If this is not what
Mar 31 14:33:11 rad2 dhcpd: you want, please write a subnet declaration
Mar 31 14:33:11 rad2 dhcpd: in your dhcpd.conf file for the network segment
Mar 31 14:33:11 rad2 dhcpd: to which interface eth0 is attached. **
[Code]...
View 1 Replies
View Related
May 26, 2011
I have a DHCP server running on CentOS and for some reason it is assigning the highest number from the IP range as a first one?
- range 192.168.1.20 - 192.168.1.50 - so the first IP on my PC recived from this DHCP server was .50 - is it normal behaviour?
Config file:
View 1 Replies
View Related
May 10, 2010
I'm trying to install CentOS 5.4 from my local repo, booting the server from centos54-netinstall iso (vmware). I write "linux URL..." during boot. I eventually get prompted for network config, where I choose manual configuration. Hitting OK ignores my config and defaults back to dhcp, which won't work since I don't have any dhcp server available.Whats wrong? Is there a bug in anaconda?
View 1 Replies
View Related
Sep 21, 2010
I have openvpn tunnel setup between two CentOS servers. One of the CentOS servers also acts as a DHCP server for some client computers.
Server A= OpenVPN server
Server B= OpenVPN client (connects to Server A with OpenVPN)
The two CentOS servers can ping each other (172.16.0.0/24) via the tun0.
However, client computer connected to Server B (DHCP server) can't reach 172.16.0.1 (which is the OpenVPN server).
I think I am missing some routing in my "ip route show". Following is the full picture:
What command can I issue to get this fixed? something along ip route add?
There is no firewall service on both end. service iptables stop! I can't bridge eth1 and tun0 as DHCP server might mess up the other side. I can't do a push of "redirect-gateway def1" because then clients loose their IP as they send DHCP requests to Server A.
View 2 Replies
View Related
Oct 22, 2010
Back in April I set up a Ubuntu DHCP server and a multiple VLAN network [URL] to migrate our various servers, workstations, etc off the 192.168.1.1 /24 network that everything was on because we where running out of address space. I built out the new network and everything worked great except our AD server would never get an IP address from the DHCP server (static reservation) and even if I set the IP statically on the AD server it couldn't ping the gateway and noone could log in. After several attempts to resolve this, including bringing in outside help, we where never able to figure out what the problem was.
Now 6 months later I have time to revisit the issue without effecting the live network. I used Acronis and imaged the AD server last Friday, cloned it on to another box with the same hardware, and put it up on the new network that's been sitting unused for the last 6 months. Today when I statically set the IP on the AD server (which is what I want) it connects and I can ping it's gateway 192.168.1.1 and all the way across vlans to a test sales agent workstation at 192.168.8.xxx on vlan 800 but only if I statically assign the agents station an IP address. When I try to get an IP address via DHCP it fails as destination unreachable. Nothing has changed in the last 6 months on the DHCP server but now it for some reason can't ping its default gateway 192.168.1.1. All of the config files are the same as they where left from the post linked above aside from the vlan id's used where changed from 1's to 100's (i.e. vlan 3 is now vlan 300) /etc/network/interfaces
Code:
auto lo
iface lo inet loopback
auto vlan100
iface vlan100 inet static
[code]....
why it can't reach the gateway, when I do a tcpdump I can see the DHCP requests come in on eth0 but the server never responds and I'm pretty sure its because it isn't "seeing" them since it thinks there isn't a network connection but I don't know how to trouble shoot to find out where the problem lies.
View 6 Replies
View Related
Jul 1, 2010
Back in April I set up a Ubuntu DHCP server and a multiple VLAN network [URL] to migrate our various servers, workstations, etc off the 192.168.1.1 /24 network that everything was on because we where running out of address space. I built out the new network and everything worked great except our AD server would never get an IP address from the DHCP server (static reservation) and even if I set the IP statically on the AD server it couldn't ping the gateway and noone could log in. After several attempts to resolve this, including bringing in outside help, we where never able to figure out what the problem was.
Now 6 months later I have time to revisit the issue without effecting the live network. I used Acronis and imaged the AD server last Friday, cloned it on to another box with the same hardware, and put it up on the new network that's been sitting unused for the last 6 months. Today when I statically set the IP on the AD server (which is what I want) it connects and I can ping it's gateway 192.168.1.1 and all the way across vlans to a test sales agent workstation at 192.168.8.xxx on vlan 800 but only if I statically assign the agents station an IP address.
When I try to get an IP address via DHCP it fails as destination unreachable. Nothing has changed in the last 6 months on the DHCP server but now it for some reason can't ping its default gateway 192.168.1.1. All of the config files are the same as they where left from the post linked above aside from the vlan id's used where changed from 1's to 100's (i.e. vlan 3 is now vlan 300) /etc/network/interfaces
Code:
auto lo
iface lo inet loopback
auto vlan100
[code]....
why it can't reach the gateway, when I do a tcpdump I can see the DHCP requests come in on eth0 but the server never responds and I'm pretty sure its because it isn't "seeing" them since it thinks there isn't a network connection but I don't know how to trouble shoot to find out where the problem lies.
View 2 Replies
View Related
Mar 25, 2010
I am puzzled with trying to configure a linux (openSUSE) client to dhcp to eBox DHCP server. I am using dhclient to lease an IP address with dhclient eth0 -s 10.45.48.108 and get a response
openSUSE11232CL1 dhclient: DHCPDISCOVER on eth0 to 10.45.48.108 port 67 interval 4
openSUSE11232CL1 dhclient: DHCPOFFER from 10.45.48.108
openSUSE11232CL1 dhclient: DHCPREQUEST on eth0 to 10.45.48.108 port 67
openSUSE11232CL1 dhclient: send_packet: Network is unreachable
openSUSE11232CL1 dhclient: send_packet: please consult README file regarding broadcast address.
The server reports eBox141 dhcpd: DHCPDISCOVER from 00:0c:29:3e:57:a3 (openSUSE11232CL1.domain.net) via eth0
eBox141 dhcpd: DHCPOFFER on 10.45.200.2 to 00:0c:29:3e:57:a3 (openSUSE11232CL1.domain.net) via eth0
I interpret this as the server receives the request and the client accepting it but the lease does not last long and the connection breaks. what this could be and why the connection breaks? Or my undestanding is totally wrong on how it works and should work? And BTW, where is that README file that's referenced in the message I receive on the client?
View 2 Replies
View Related
Mar 8, 2010
Currently I have my eth0 interface getting a DHCP address but at times the DHCP server will not be reachable. Sooo what I would like my server to do is if it cannot find a DHCP server assign a static address to eth0. Then start the DHCP service so it can then dish out some addresses.How can I do this? Surely it is possible
View 2 Replies
View Related
Aug 4, 2010
I have an embedded device for which I've created an html configuration page. This page allows you to set static IPs, dhcp, and can scan for wireless devices.My problem is that in order to access the device it requires that it runs as a dhcp server otherwise people are not assigned an IP and so can not access the embedded devices static IP. (This config page is for the laymen and so they are not the type who are able to set up their own static IPs). One of the potential options is to have the device connect to the network on eth0 acting as a dhcp client. However this prevents me from running a dhcp server.One solution I can think of is running a dhcp server only if it doesn't detect another dhcp server running on the network.
View 4 Replies
View Related
Mar 27, 2010
How to install DHCP server in ubuntu 9.10, i googled but not able to find correct how to. if anyone installed provide steps in configuring dhcp3.conf file
View 1 Replies
View Related
Mar 27, 2010
I am at first stage of installing dns after installation of redhat 5 am unable to install any package like yum install bin* and yum install cach* and it displays no match for afgument and nothing to do what could be the problem with my redhat installtion and what should i do for this type of problem and explain me how to install bind in dns and dhcp and dc.
View 3 Replies
View Related
Feb 8, 2010
first: PXE flawless bind to dhcp address but put next binding state to free second: when installer calls init script to reinit ethernet driver (e1000 (vmware)) binding fails 11.2 opensuse fail to reinit dhcp with log entry "no free leases" third: when manual set network install works how to preserve dhcp lease on reinit of driver?
View 1 Replies
View Related
Aug 10, 2011
Does anyone know how to install the DHCP Server for the DSL 4.4.10 version. Cant find installation instructions anywhere.
View 1 Replies
View Related
Jan 24, 2011
This dhcp server is configured with redhat enterprise edition. I found that logs are generating in the following path /var/log my doubt is how can i setup the logs generating for a specified day.
View 1 Replies
View Related
Aug 1, 2011
After a fresh install of Ubuntu 11.04 (from 10.04) and spending several hours trying to figure out why the ad-hoc connection between my two computers (Fedora14 <-> Ubuntu 11.04) no longer worked - it had worked fine for almost 2 years with 10.04 - I've finally concluded it was a DHCP problem. This realisation (which was slow in coming!) dawned on me when I reversed my setup and configured the Fedora box as the DHCP server and everything was suddenly working perfectly! A quick internet search threw up an installation file called "isc-dhcp-server" which other Ubuntu 11.04 - related forums are also complaining about. My problem is that this file, although available in the repository, is not even installed!!!
It seems unlikely that the developers forgot to include DHCP support, so I hope someone can point me in the right direction.
View 1 Replies
View Related
Feb 7, 2011
I need to install/configure a server (dns, dhcp, etc) and since im running Debian I want to configure a Debian server, but i want to do it on a virtual machine, cause i dont want to have all that stuff on my system, now Im wondering whats the best screen recorder that i can use on Debian for this purpose.
View 3 Replies
View Related