CentOS 5 Hardware :: System Did Not Appear To Resume Correctly From Suspend / Hibernate
Feb 19, 2011
i dont know why my system dosnt resume from suspend sstate.i it goes in suspend state.it doesnt resume .i have to poweroff then restart it again.and when i get logged in it gives me Following Error: Resume problem: Your system did not appear to resume correctly from Suspend/Hibernate. This may be a driver problem or a hardware problem. Check the GNOME Power Manager Manual for common problems.
do you think it is because of batterry.i have a problem in my By Battery .IN DOS operating system.when i check my battery icon . A red Cross constantly blink on lower right side of the battery and it says (your Battery consider Replacing).i have notice one thing .And My battery timing hias become Decreased. Do you think this Resume problm is cause of battery problm.Or there is some problm in my Os software.
View 3 Replies
ADVERTISEMENT
Apr 7, 2010
I just got a Dell Inspiron 1764 and am dual booting it with Win7 and Ubuntu 9.10.Whenever I hibernate or suspend, it goes through everything fine, but then when I resume it just boots to a black screen and I have to do a hard shutdown. Is there a fix for this? I know it's a fairly common issue.
View 1 Replies
View Related
May 9, 2010
I've got a Thinkpad X31 with ATI M6 Ly card. Since Karmic, and Lucid, I get no suspend/hibernate/resume. If/when I select resume or close the lid, Lucid goes through the suspend cycle, and for approximately half a second it actually seems to go into suspend, then the screen comes back on, black, but definitely on, and absolutely no response to any keyboard input - have to hard-shutdown by holding down the power button. I've read that the problem is with the Ubuntu kernel, and that installing/compiling 2.6.33 fixes the issue, but causes other ones.
View 4 Replies
View Related
Mar 13, 2011
The good news: 11.4 seems to have much better support for my radeon graphics driver which makes many of my workarounds for 11.3 unnecessary
The bad news: whereas previously for 11.2, 11.3 using traditional ifup meant that I could easily restore internet (either wlan0 or eth0) with ifdown/ifup now this seems to have no effect. I haven't investigated further yet since without internet on hibernate or suspend 11.4 is not my grub of choice at the moment
There seem to be quite a few glitches with the 'stable' release of 11.4 but this seems to be the main problem for me. (Minimizing the beta 4 Firefox windows closing them is another...)
View 4 Replies
View Related
Aug 30, 2010
After I resume from hibernate with my cpu frequency manually set to the highest settings (2ghz) the network manager shows not wifi APs. "wlan0" shows under both ifconfig and iwconfig but "iwlist wlan0 scan" says no results. "sudo iwlist wlan0 scan" also says no results. I've tried rmmod then modprobe with no luck. Rebooting is the only way I can get WiFi working.
I can get wifi working again by:
- rebooting
- changing the cpu scaling to a lower setting then hibernate/resume
- changing the cpu scaling to a lower setting then 'sudo rmmod ath9k; sudo modprobe ath9k;'
I am using Ubuntu 10.04 with Atheros ar5008 (AR5BXB72) using ath9k drives
Code:
$ lspci |grep Atheros
0e:00.0 Network controller: Atheros Communications Inc. AR5008 Wireless Network Adapter (rev 01)
Code:
$ uname -r
2.6.32-24-generic
View 9 Replies
View Related
Mar 21, 2009
For the sake of security, I want the screen to be locked after the system is resumed from suspend or hibernation. Now the only way I can do this is to check the options "Lock screen when screen saver is active." in the screensaver preference. But this method is annoying since I have to type the password to quit the screensaver. Is there other way to do this? Thanks.
By the way, I use CentOS 5.2 x86_64.
Leonard
2009-3-21
View 1 Replies
View Related
May 18, 2009
My computer have ATI X600 graphics card installed, and I installed CentOS5.3.
Every time I suspend my computer and then resume it, it seem the graphics card can't resume and the monitor says 'no signal', but the system still responses, I can use keyboard.
Is there any configuration I can't do to make it resume normally? I've searched a lot in Google but can't find out any one else run into the same problem.
Information about the card:
Quote:
View 5 Replies
View Related
Aug 6, 2010
I am running Squeeze on an older Compaq EVO laptop with radeon graphics.
A few months ago, after an upgrade, suspend and hibernate stopped working. The suspend or hibernate worked fine, but the resume just hung with a black screen. I finally got around to looking into it and found a workaround.
The workaround is to disable Kernel Mode Setting for the radeon. This can be done by adding the boot parameter "radeon.modeset=0" or by editing /etc/modprobe.d/radeon-kms.conf so that it includes the line "options radeon modeset=0".
If you are interested in the details, you can search for problem reports related to radeon kernel mode setting.
View 3 Replies
View Related
Mar 16, 2010
Just got Ubuntu 9.10 and I'm liking it a lot, but my computer refuses to go into hibernate or suspend. I have a Dell M1530 but I don't really think it's a dell hardware issue because it's not just when I close the screen, it's also when I click suspend or hibernate from the menu.
View 2 Replies
View Related
Jul 12, 2011
I've been trying to find an answer to the following problem : whenever my PC is put in Suspend/Hibernate mode, it fails to recover when pushing the power button. This happens both with automatic suspend or manual suspend. I've been reading this problem, and mine is quite similar, but no solution is given.
uname -rmi
2.6.18-194.11.4.el5 x86_64 x86_64
PS: this computer is not connected to Internet, no update possible.
View 1 Replies
View Related
Jun 17, 2011
I am having a problem with suspend in F15. While the computer enters and resumes from suspend extremely fast (basically instantaneous), the whole system seems sluggish and unresponsive afterwards. The mouse cursor is lagging and some key strokes are omitted when typing. The animations in Gnome 3 are also very non-fluid compared to how they were before suspend. The only way I have found to return to normal operation is to reboot the computer. I have tried 32 and 64-bit versions of Fedora 15 with the problem existing in both. I also tried the latest version of openSuse (Gnome 2.32) just to see if this problem persisted and I can confirm that it did. Perhaps this indicates a kernel-related problem that should be reported as a bug somewhere else?
lspci:
Code:
00:00.0 Host bridge: Intel Corporation Core Processor DMI (rev 11)
00:03.0 PCI bridge: Intel Corporation Core Processor PCI Express Root Port 1 (rev 11)
00:08.0 System peripheral: Intel Corporation Core Processor System Management Registers (rev 11)
00:08.1 System peripheral: Intel Corporation Core Processor Semaphore and Scratchpad Registers (rev 11)
00:08.2 System peripheral: Intel Corporation Core Processor System Control and Status Registers (rev 11)
00:08.3 System peripheral: Intel Corporation Core Processor Miscellaneous Registers (rev 11) .....
View 3 Replies
View Related
Jun 16, 2011
Suspend / hibernate locks up my system.
View 4 Replies
View Related
Mar 31, 2011
Machine is a Dell Optiplex GX260, Pentium 4 with ATI Radeon RV200 QW [Radeon 7500]. I believe this is an AGP graphics card. I also believe that the graphics card is the root of my problem. In Karmic, I could get the computer to suspend. but it would not resume. The monitor would not initiate and it seemed as though the system froze. Only way out was a hard reboot. Hibernate worked for me without any problems, so it was no deal breaker. Now in Meerkat, Suspend behaves exactly as before. However, I can not get the system to go into hibernation.
The monitor goes down, but the system seems to freeze and never go down. I have tried editing the options in the acpi-support file to no avail. I have tried disabling compiz (which works amazingly well with this card), to no avail. I am using the open-source drivers and I have not tried the closed-source drivers in this system. I tried the closed-source drivers in Karmic and they made no difference. I may try un-installing the ATI card and fall back on the on-board Intel chipset to see if that solves the problem. Only then, I will loose 3d effects, etc.
View 9 Replies
View Related
Aug 7, 2011
Lately I upraded my Debian using aptitude update/aptitude upgrade - including installing a new kernel (3.0). Since this upgrade I have strange problem with networking. When I suspend my computer and resume it, I do not have connectivity with network:
$ ping 192.168.1.1
PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data.
From 192.168.1.1 icmp_seq=1 Destination Host Unreachable
[code]....
View 2 Replies
View Related
Aug 13, 2010
I recently upgraded to Lucid (x86_64) on an HP dv2 laptop, and after doing so, the system will not resume after a suspend (with fglrx installed from the "official" repositories). After reading a lot about the problem, I have seen that updating to the latest ATI driver had fixed this issue for some, so I would like to try that.
I am following the guide at at cchtml.
First, I tried installing the Ubuntu-X team's drivers. However, after (successfully) adding their repository, an update does not fetch their packages:
Code:
It looks like both the xorg-edgers and ubuntu-x-swat repositories are being ignored? (If I'm reading that correctly.) If I open the window System->Administration->Software Sources, I can see that the ubuntu-x-swat repository is checked, so I'm confused why it's being ignored.
If I try to demand the fglrx-installer package, I get an error that it cannot find this package.
Code:
I have the same issues for xorg-edgers and ubuntu-x-swat.
Finally, if I try to build the official ATI v10.7 drivers myself, I get an error that Linux is an unrecognized architecture!
Code:
I have installed all preliminary packages suggested in the guide:
Code:
I really can't understand why I'm unable to build the package from ATI myself.
View 3 Replies
View Related
Nov 27, 2010
I have a desktop system (P55-USB3 + Core i7 + Ubuntu 10.10) that fails to suspend/resume from memory. So I'm trying to diagnose the problem. The first obstacle was easy enough --- when I put the system to sleep to memory, the computer comes back alive right away. A look at /var/log/kern.log revealed that one USB device (usb10) failed to suspend, and from there I was able to pin it down to the USB3 controller in the BIOS. Disabled that and this problem disappeared.
Now, I'm stuck with the second obstacle. The computer successfully goes into the suspend mode, but it hangs during resume. The monitor doesn't get any video signal, and it fails to respond to ping (netconsole doesn't work either.) After a forced reboot (that involves unplugging the power cable), /var/log/kern.log doesn't contain any interesting entries. All the pm_test modes from freezer to core succeed (I followed [URL] I've also tried pm_trace (https://wiki.ubuntu.com/DebuggingKernelSuspend) but again kern.log nor dmesg contains anything after the suspend. Either the write didn't survive the forced power off, or the resume is failing even before that. The motherboard doesn't have a serial port nor firewire, so getting kernel logs through them is not a possibility, either.
View 3 Replies
View Related
May 21, 2015
My system cannot resume after hibernation. I have done all as described here [URL] ...
My have set up swap file "/swap_debian".
I have 3 partitions: sda1: windows boot partition. sda2: windows 8.1. sda3 : debian
I have the only linux distro installed: debian.
I have read lots of web pages. I have managed to set up suspend 2 disk. After dancing 2 days at the computer the system still cannot resume. I am getting "clearing orphaned inode" msgs while booting, and when booted to ram was not recovered.
Swap file is 4000 MB, RAM is 3860 something MB
My current grub is:
Code: Select all# If you change this file, run 'update-grub' afterwards to update
# /boot/grub/grub.cfg.
# For full documentation of the options in this file, see:
# info -f grub -n 'Simple configuration'
[Code] ....
And yes, I did update-grub.
My current /etc/uswsusp.conf is:
Code: Select all# /etc/uswsusp.conf(5) -- Configuration file for s2disk/s2both
resume device = /dev/sda3
compress = y
early writeout = y
image size = 1855258869
RSA key file = /etc/uswsusp.key
shutdown method = platform
resume offset = 31606784
My current /etc/fstab is:
Code: Select all# /etc/fstab: static file system information.
#
# Use 'blkid' to print the universally unique identifier for a
# device; this may be used with UUID= as a more robust way to name devices
# that works even if disks are added and removed. See fstab(5).
[Code] ....
View 0 Replies
View Related
Mar 28, 2010
I found this line in dmseg when I was checking out another problem.
"[0.104467] ACPI Warning: Incorrect checksum in table [OEMB] - 03, should be FA 20090521 tbutils-246"
Could this be why I have never been able to resume from hibernate on this machine?
View 1 Replies
View Related
Oct 14, 2010
I have ubuntu 10.04 installed on a 50 gb partition on my hard drive I have given a 3.5 gb partition for swap which is > 3gb ram i have. Druing the installation of ubuntu I had specified the swap partition and its hibernate was working fine sometimes before. But I had to delete the swap partition and recreate it because of some reasons so I did that and again created a 3.5 gb partition for swap space usig ubuntu live cd.
But after restart ubuntu no longer detected the swap partition it was ok as its uuid had changed so I specified the swap partition to be mounted automatically by adding an entry in /etc/fstab and then also added the same UUID in /etc/initramfs-tools/conf.d/resume so that it could resume. After restarting ubuntu after adding the entrly in /etc/fstab i got the option of hibernate but after hibernate everything goes well but after hibernate when i start laptop again ubuntu first tries to resume but it does not and without giving any message it shows the login screen.
View 8 Replies
View Related
May 3, 2010
I'm experiencing very slow resume from hibernation. Last one was nearly 3 minutes. Sure, there is 2GB of RAM to read from disk (no SSD) to memory but that long?What could I check/do?
View 4 Replies
View Related
Oct 17, 2010
I'm using stock 32 bit current on a AAO D250 netbook. I'm running into a video issue after upgrade to the recent 2.6.35.7 kernel that doesn't exist after resume from suspend. The condition shows as a broken display that shows a black screen on the left with the KDE desktop partial exposed on the right side. Weird! My only fix so far is to blindly ctrl-alt-f6, login as root and reboot. The screen does not show the console screen during this reboot process
The pm-suspend logs show a clean hibernate and a clean thaw so that's no help. I've checked modprobe.d and don't have any alterations to any of the modules. The video module loaded is the intel_agp which sound right. I'm stumped at the moment.
View 14 Replies
View Related
Apr 13, 2010
So I'm having this weird problem where my computer wants to continuously resume a session from hibernate no matter how I shut it down. I think it started when I tried to hibernate my computer with the battery really low. Somehow it messed it up. In any case, it can't resume properly, but gets stuck somewhere in the middle (I think when it's trying to sort out the resume image). Each time I power it on I have to boot it, restart in the middle of the boot so the boot menu comes up as it starts up again, edit commands before boot and add the "noresume" option so it will boot up normally.
View 2 Replies
View Related
Mar 12, 2010
I am pretty new to Linux, but this can't be the way the system is supposed to operate.
Fedora 12
KDE 4.4
kernel 2.6.32.9-70.fc12.i686
Toshiba satellite L305D
As of updating KDE to 4.4 and a kernel update from two weekends ago hibernate/resume works perfectly. The problem is I feel that all terminals should be locked/logged out automatically upon suspend/hibernate. Through bug reporting at KDE found that an additional setting is required in KDE to lock the desktop before suspend/hibernate. But any of my other terminals that are logged in remain logged in upon resume. Is there an additional setting that I have to flip to secure the terminals? Would this be considered a security hole? Is there anything short of me manually logging out that I can do to automate locking/logging my terminals?
View 1 Replies
View Related
Jul 9, 2011
I have problem with resuming after hibernate, it is about 50% chance that computer restart when I want resume, then it starts boot normally and all my work is lost.
Acer aspire 3820tg
Ubuntu 11.04
Builtin hibernate on partition
I try uswsusp s2disk ... on resume it always stops in half of process. I used mainly hibernate, but I'm lost now.
View 9 Replies
View Related
Jan 28, 2010
I am looking for a tool in fedora which can hibernate/standby and also resume after a few seconds automatically with a command. If we have that option by default in fedora.
View 1 Replies
View Related
Jun 15, 2011
I'm using CentOS 5.6, kernel version 2.6.18-238.12.1.el5xen, and the Hibernate and Standby options don't even appear in the System menu. How can I get them to appear?
The funny thing is that before I reset my system to a clean install of CentOS 5.6, I was able to see those entries and execute them just fine. (I think that in that previous installation, by doing some updating of packages I got another kernel version and booting into that one showed the menu items.)
Could it have something to do with the fact that it's a xen kernel? Even though I've disabled xend, it doesn't appear.
View 2 Replies
View Related
Apr 6, 2010
My laptop won't resume after it suspends. It works fine under win 7 so it's not the hardware. The light says it's on and it's pretty much a blank screen. I'm not sure whether it's operational but the screen is off. It has exactly the same resault a waiting for the blank screen except it won't go back on.
View 9 Replies
View Related
May 6, 2010
I've just upgraded from 9.10 to 10.04 via the upgrade manager. Prior to the upgrade I was able to suspend and hibernate without any problems. Now that I have upgraded to 10.04, I can suspend however when I resume I am back at the gdm login prompt, logging in again with a new session.Having just done another test whilst writing this, it actually appears that if I select suspend from the top right I am suspended and can resume my session. If I close the lid on my laptop (which is supposed to suspend) I am logged out and suspended.Also, Hibernate doesn't work as well - sometimes it never actually hibernates (just sits on a black screen) and sometimes it doesn't resume (it's never hibernated and resumed correctly since the upgrade)
View 9 Replies
View Related
Mar 10, 2010
I have an issue with my Sony vaio fw31e not resuming from suspend. Reported this as a bug: [URL] The usual ways of suspending, from the kde 4 menu, from the power/battery widget or by lid closing always result in no resume. However, running pm-suspend from a root terminal suspends and resumes just fine. My question is, how does one delve into the way that the usual methods initiate suspend? Maybe if I could find out what each of these methods actually does, I may be able to see what is going wrong? I had been running squeeze on this lappy since July 2009 with no suspend issues until an update broke it sometime in January. The install is being fully upgraded every day at the moment.
View 11 Replies
View Related
Nov 13, 2010
It all works if I boot my self compiled vanilla 2.6.35-rc3 though. The environment
Sony vaio VGN-SR21M 4GBRAM P8400, ATI HD3400 mobility. I use
kernel-2.6.35.6-45.fc14.x86_64
xorg-x11-drv-ati.x86_64-6.13.1-0.3.20100705git37b348059.fc14
If I suspend my notebook it starts the usual slow orange blinking indicating the suspend mode got reached. There is also evidence in the various log files that this works. If I try to resume it hangs a for 3 seconds and then I get the hdd-password screen from my bios and the notebook boots from zero. I couldn't find anything in /var/log/messages nor dmesg. If I first boot to windows (grub 2nd partition) and then restart and boot to linux, all the suspend works fine
View 1 Replies
View Related
