Fedora :: Suspend / Hibernate Locks Up System?
Jun 16, 2011Suspend / hibernate locks up my system.
View 4 Replies
ADVERTISEMENT
Ubuntu :: Suspend Or Hibernate / Computer Refuses To Go Into Hibernate Or Suspend?
Mar 16, 2010Just got Ubuntu 9.10 and I'm liking it a lot, but my computer refuses to go into hibernate or suspend. I have a Dell M1530 but I don't really think it's a dell hardware issue because it's not just when I close the screen, it's also when I click suspend or hibernate from the menu.
View 2 Replies View RelatedUbuntu :: No Suspend Or Hibernate - System Froze
Mar 31, 2011Machine is a Dell Optiplex GX260, Pentium 4 with ATI Radeon RV200 QW [Radeon 7500]. I believe this is an AGP graphics card. I also believe that the graphics card is the root of my problem. In Karmic, I could get the computer to suspend. but it would not resume. The monitor would not initiate and it seemed as though the system froze. Only way out was a hard reboot. Hibernate worked for me without any problems, so it was no deal breaker. Now in Meerkat, Suspend behaves exactly as before. However, I can not get the system to go into hibernation.
The monitor goes down, but the system seems to freeze and never go down. I have tried editing the options in the acpi-support file to no avail. I have tried disabling compiz (which works amazingly well with this card), to no avail. I am using the open-source drivers and I have not tried the closed-source drivers in this system. I tried the closed-source drivers in Karmic and they made no difference. I may try un-installing the ATI card and fall back on the on-board Intel chipset to see if that solves the problem. Only then, I will loose 3d effects, etc.
CentOS 5 Hardware :: System Did Not Appear To Resume Correctly From Suspend / Hibernate
Feb 19, 2011i dont know why my system dosnt resume from suspend sstate.i it goes in suspend state.it doesnt resume .i have to poweroff then restart it again.and when i get logged in it gives me Following Error: Resume problem: Your system did not appear to resume correctly from Suspend/Hibernate. This may be a driver problem or a hardware problem. Check the GNOME Power Manager Manual for common problems.
do you think it is because of batterry.i have a problem in my By Battery .IN DOS operating system.when i check my battery icon . A red Cross constantly blink on lower right side of the battery and it says (your Battery consider Replacing).i have notice one thing .And My battery timing hias become Decreased. Do you think this Resume problm is cause of battery problm.Or there is some problm in my Os software.
Fedora :: How To Disable Hibernate Or Suspend?
Dec 18, 2009I have a web server running on my laptop(in fact , it's a netbook). But I found it always hibernate automatically in a certain time .(In fact , I don't know what's the differences between hibernate or suspend. So I call this hibernate instead.) I am sure I have disabled the hibernate function in Power-Management from the System menu. But it still hibernates as usual.So could someone tell me how to disable it ( suspend,hibernate whatever )?
View 6 Replies View RelatedGeneral :: Difference Between Suspend And Hibernate In Fedora?
May 25, 2011I have fedora 13. What is the difference between suspend and resume? If I suspend, how do I turn on the pc? If I hibernate, how do I get out of hibernation?
View 3 Replies View RelatedFedora Hardware :: 13 - Acer Aspire One 721 - Plymouth / Enable Wireless / Suspend/Hibernate
Jul 17, 2010I have three problems with my new Acer Aspire one 721 (Amd, ATI) [url]
1) Pymouth doesn't work when booting. I have to use the parameter "nodeset". Desktop effects are working. I have installed Mesa based DRI drivers (experimental).
2) I have to manually "enable wireles" to acess the wlan. It should connect automatically.
3) the laptop doesn't wake up from suspend/hibernate. I have to use brute force to restart. pm-suspend.log
Code:
Fedora :: Hibernate / Suspend Doesn't Work - Caps Lock Starts Blinking
Aug 1, 2011everything works perfect including reboot and shutdown but not the hibernate or suspend (sleep). Whenever i try to do Suspend, my caps lock starts blinking and the screen goes white
View 2 Replies View RelatedUbuntu :: Hibernate Does Not Work / Locks Up Before Even Shutting Down
Jan 24, 2010I am using Xubuntu 9.10, 2.6.31-17-generic kernel. Video driver: "ati".I have only been using Linux for less than a year now but I have never been able to get hibernate mode working. Had the same problem on previous kernels and with Nvidia drivers. Tonight I tried removing all traces of any nvidia drivers hiding in my system (I recently changed to an ATI card), and also upgrading to grub 2. Still no luck.If I use the "hibernate" option from the shutdown menu, I just get a black screen with a blinking cursor. If I use s2disk, I get a little bit more of a hint, but still not very helpful. Then it just locks up after that. Power is still on and it never shuts down. I have a 6 gig swap partition set up that is enabled, so it is definitely not a swap issue.
View 2 Replies View RelatedFedora :: Fedora Will Not Hibernate Or Suspend
Apr 25, 2010my system will not go to suspend, if I was logged on. It will turn off the fan and harddrive and than nothing will happen. I can't stroke a key, it will only blink on a blank screen. So I have to switch off my system by holding down the power-key for a while. But if I was never loggod on, I can suspend properly on the welcomescreen.
View 9 Replies View RelatedUbuntu :: USB Keyboard Locks Up After Resume From Suspend
Feb 20, 2010When I suspend my computer and then resume later in the day my USB keyboard locks up. The only way I have found to reset the keyboard is to disconnect the USB cable from the USB port and then reconnect it.
View 9 Replies View RelatedUbuntu :: Can't Suspend Or Hibernate?
Apr 13, 2010I recently installed Ubuntu 10.04 Lucid Lynx. When I partitioned my HDD, I ran out of available partitions and so couldn't make a Swap Partition.I pushed on anyway, because I read here that you can create a Swap File instead of a partition that does the same thing. I've made the Swap File and it's activated (I know because during shutdown there's a message that flashes very quickly that says "Deactivating Swap [OK]".
But here's the real problem. My Ubuntu refuses to Suspend or Hibernate. The screen just goes black and the backlight stays on. Since one of the main functions of the swap file is to facilitate Suspend and Hibernate,I upgraded from 9.10 Karmic Koala, which suspended and hibernated normally.
Debian :: Get Suspend And Hibernate Working?
Apr 29, 2011I have already installed gnome-power-manager.
There should be the suspend and hibernate buttons in th System Menu, but there is only two options, Shut down and Log off.Also, in the Power Manager Preferences window, it has no option for suspend and hibernate.
How to add suspend and hibernate options?
Debian Multimedia :: Suspend And Hibernate In KDE?
Feb 16, 2011Is there an "official" way to add suspend and hibernate functionality to the KDE logout/shutdown menu in Squeeze? What packages do I need?
ps. My computer is not a laptop - it's a normal desktop machine
Ubuntu :: Cannot Suspend (hibernate Or Sleep)
Mar 15, 2010kubuntu 9.10, KDE 4.4.1, Nvidia driver 195
jeff@jeff-lappy:~$ sudo hibernate hibernate:Warning: Tuxonice binary signature file not found. Some modules failed to unload: nvidia hibernate: Aborting suspend due to errors in ModulesUnloadBlacklist (use --force to override).
I even installed this tuxonice thing but to no avail...
Ubuntu :: Hibernate And Suspend- Can't Wake Up
May 4, 2010I can Suspend or Hibernate my Gateway notebook but I have no idea how to wake it up.The power button is set to suspend or hibernate....I not sure which it does, but I can't wake the computer up.
View 9 Replies View RelatedUbuntu :: Suspend And Hibernate Not Working?
Oct 15, 2010My suspend and hibernate buttons are not working. When I try to return from a suspend, I do not get a kernel panic, but nothing loads onto the screen.
View 7 Replies View RelatedUbuntu :: Log Files For Suspend/hibernate?
Jan 12, 2011which ubuntu log file records when a suspend happened?I was ssh'ing into my ubuntu box periodically yesterday, when I discovered that it was no longer reachable. On getting home last night I discovered that it was still switched on, but I think in suspend mode as moving the mouse brought it back to life. The clock however, still showed 12:15pm, which is roughly when I stopped being able to ssh to it. I'd like to see the logs to confirm this.
View 9 Replies View RelatedUbuntu :: Unable To Suspend Or Hibernate?
Feb 12, 2011My Ubuntu 10.10 on my laptop Lenovo T400 is not able to suspend or hibernate. Whenever I click Suspend or Hibernate in Startup options of the OS: * the moon LED on the bottom of the lid flashes a few seconds, the screen quickly shows something like "some devices fail to suspend, error 5", * and then the moon LED goes off and the display still has ambient light illumination. I suppose in suspend or hibernation state, the display should have no illumination, just like when the laptop is turned off, right? * If I press any key, the unlock screen dialogue will pop out. I have installed 'acpi-support' and 'hibernate 1.99-1.1'. But I don't know how to use these methods to suspend or hibernate my OS. Are they by commands in terminate, or can they be called by clicking Suspend or Hibernate in Startup options of the OS? For example, I type the hibernation command and it shows something is missing although I have installed "tuxonice-userui" ( I don't know if it will provide Tuxonice binary signature file):
Code:
$ sudo hibernate
hibernate:Warning: Tuxonice binary signature file not found.
[Code]....
Slackware :: Can't Suspend - Hibernate / Resolve This?
Jun 23, 2010I'm using the version 13 of Slackware. I can't suspend or hibernate my OS. I need something named HAL.
Searched a bit on the net but couldn't really figure something out.
Debian :: When Suspend And Hibernate Screen Goes Black?
Feb 26, 2011I am having some pain with my new Squeeze installation, I am not sure if I am asking to much of it or it is an easy fix.
Firstly my system is laptop which I regularly plug a second monitor into. The video adaptor is an ATI HD4550 mobile.
My problem is that when ever suspend or hibernate my system, and even sometime when I boot up the screen(s) are just blank, although sometime they don't, it always happens if I suspend by closing the lid of my laptop, and only sometime happend with through Gnome is go ->System->Shutdown->Suspend. This is really annoying.
Another issue which I think is connected is that as I said I have a second monitor (most of the time) and when I boot up then it works until I log in, then a message pops up say the configuration can not be applied and it revert to Mirror mode or it does this thing where it places the second screen inside (virtually) the built in Laptop panel, it will not let me fix this through the monitors dialog just displaying the same message. I can fix this by doing
invoke-rc.d gmd3 restart
This gets as far as killing Gnome them it prints an error the to console, at which point Imopen a new terminal by ctrl+alt+f2 and
invoke-rc.d gmd3 stop
invoke-rc.d gmd3 start
then it works fine and even remember that I set the secondary screen to be the primary monitor through xrandr.
I tried install fgrlx drivers instead but it didn't really fix the issue, so I removed them.
Debian Installation :: Suspend / Hibernate On Thinkpad T42
Jul 9, 2011I installed the debian 6 on the tninkpad T42, use the Suspend,it can entry the suspend state，I type the key let it come back, it can exit the suspend state, But the screen always display "black",can't come back the X window.
View 2 Replies View RelatedDebian Configuration :: Can Only Suspend / Hibernate As Root
Oct 28, 2015Installed Debian 8.2 a while back, and I've been having issues with getting the machine to suspend correctly. If I try to put it to sleep when logged in to my regular user account the screen just goes black and then the computer hangs. However if I put it to sleep as root everything works fine. I do this by running this command (as root):
Code: Select allsystemctl suspend
What can I do about this? Worked fine on Debian wheezy..
Btw, just found this in the dmesg log. Connected perhaps..?
Code: Select all[ 6.863018] ACPI Warning: SystemIO range 0x00000000000018e0-0x00000000000018ff conflicts with OpRegion 0x00000000000018e0-0x00000000000018ef (\_SB_.PCI0.SBUS.SMBI) (20140424/utaddress-258)
[ 6.863028] ACPI:
If an ACPI driver is available for this device, you should use it instead of the native driver
Debian Configuration :: Suspend And Hibernate Do Not Work At All
Sep 6, 2011I've been running 6.0.2 amd64 stable since release day and recently have noticed my suspend and hibernate do not work. Normally I have transmission running and have set it to not enter sleep mode while torrents are active. However today I have not had transmission and was wanting to see if the sleep mode options would kick in. So I have set my display to "sleep when inactive for" 5 mins (this works perfect)
I have set "put computer to sleep when inactive for" 10 mins (this does not work at all)
When I try to manually test suspend my display flashes black for a few seconds but remains backlit, then asks me to log back in
When I manually go into hibernate mode my display turns off, pops back on for a second and in a terminal says something about a usb device (something failed but it happens so fast I cannot read it)
General :: How To Hibernate/suspend Using The Command Line ?
May 18, 2011Put 'nix box to sleep from command line?
I found that the solution was to do: pmi action hibernate
But when I typed in that, it showed: Error org.freedesktop.DBus.Error.ServiceUnknown: The name org.freedesktop.Hal was not provided by any .service files
Ubuntu :: MSI V601 Laptop That Won't Come Out From Neither Suspend Nor Hibernate
Jan 15, 2010I've a MSI V601 laptop that won't come out from neither suspend nor hibernate and I tried almost everything so far...what shall I do?
View 1 Replies View RelatedUbuntu :: Laptop Suddenly Won't Hibernate Or Suspend?
Feb 25, 2010I think it might have to do with an app I installed called Jupiter (http://sourceforge.net/projects/jupiter/) that missed with my power configs, I removed it but I still can't hibernate or suspend. Whenever I try to do either, my screen fades to black and nothing happens. If I move the mouse or touch the keyboard, it comes back.
View 5 Replies View RelatedUbuntu :: Computer Will Not Resume From Hibernate/suspend?
Apr 7, 2010I just got a Dell Inspiron 1764 and am dual booting it with Win7 and Ubuntu 9.10.Whenever I hibernate or suspend, it goes through everything fine, but then when I resume it just boots to a black screen and I have to do a hard shutdown. Is there a fix for this? I know it's a fairly common issue.
View 1 Replies View RelatedUbuntu :: Disable Suspend And Hibernate Options?
May 8, 2010I was looking for a way to disable the Suspend and Hibernate options from the logout menu as my laptop hangs on both and requires unplugging/battery removal to restart.
I found a few pages with instructions for older Ubuntu versions but I didn't come across anything that applied directly to 10.04 Lucid Lynx so I thought I'd post what I found worked for me on 10.04.
Open a Terminal from the Applications>Accessories>Terminal. Because the file you will be editing requires root privileges to edit, you will need to use the sudo command:
Code:
sudo gedit /usr/share/polkit-1/actions/org.freedesktop.upower.policy
Enter your password. This will then open the settings file in the text editor with the needed permissions (opening the file directly with the editor you will get an error message if you try to save the file). There are two sections in this file, the first for suspend and the second for hibernate. Near the end of each section will be a line with:
Code:
<allow_active>yes</allow_active>
Change this from Yes to No to disable. Save the changes and reboot.
Code:
<allow_active>no</allow_active>
Now the power menu will not display these options. To reverse changes just repeat the above and change from no back to yes.
Ubuntu :: Thinkpad - No Suspend / Hibernate Or Resume
May 9, 2010I've got a Thinkpad X31 with ATI M6 Ly card. Since Karmic, and Lucid, I get no suspend/hibernate/resume. If/when I select resume or close the lid, Lucid goes through the suspend cycle, and for approximately half a second it actually seems to go into suspend, then the screen comes back on, black, but definitely on, and absolutely no response to any keyboard input - have to hard-shutdown by holding down the power button. I've read that the problem is with the Ubuntu kernel, and that installing/compiling 2.6.33 fixes the issue, but causes other ones.
View 4 Replies View Related