CentOS 5 Hardware :: Installing CentOS 5.3 Using Custom ISO And Drive Disk?
Nov 10, 2009
I am having new hardware and IDE driver for that hardware as drive disk image (it8213_centos53.img). CentOS 5.3 installation is working fine with drive disk image at USB and CentOS 5.3 at DVD. Our application uses CentOS 5.3 and we build a custom kick-start ISO for installations. Using that ISO client is going to install on all hardware boxes.
Note while installing :
a) No network connection is avalible.
b) No USB isavalible.
c) No floppy is avalible.
d) Only single CD-ROM is avalible.
So, is it possible to build single custom kick-start CentOS 5.3 ISO which contains dirve disk image and entire installation will be done using that image. If so please let me know the steps to build it.
I want to install Cent OS5 on my machine. The Hard Disk is SATA. I want to discuss about how to custom partition the hard disk. In the old version there is a drop down list for manual partition the hard disk. like /,boot,swap,var etc etc. In the new version of centos 5 I can not see things like that. During installation process and in partition page there are things like:
Code: Remove all partitions on selected drives and create default layout. Remove Linux partitions on selected drives and create default layout. Use free space on selected drives and create default layout. Create custom layout.
When I choose custom layout it show me an error message. "An error has occurred-no invalid devices were found on which to create new files system. Please check your hardware for the cause of this problem."
I'd like to install centos from a USB stick on to a hard drive and also include a custom kickstart on the USB stick to run post-build scripts or install additional packages, which the additional packages would also be on the USB stick..Are there any howto's already written?
What i want to be able to do is create a custom kickstart for my centOS 5 server. I want to create a bootable cd that I can pop in my server and basically walk away for 45 minutes and I come back and its fully installed. All the directions I have read so far tell me that I have to create a seperate ks.cfg and then I need my original centos cd to get it booted. Then the cd will ask for where the ks.cfg file is and I have to type the location. I just want to pop the CD in and type in linux_clean or something and have it perform a custom install based on the information and specification in my ks.cfg. How can I go about doing this?
I'm a subscriber of a Linux magazine who sends me 2 dvds of Linux distros each month. I wanna try some of those just for some time pass. The issue is that out of 52 GB partition on which Fedora 11 is installed, 42 GB is free. I want to have around 10 GB space from that 42 GB so that I can install CentOS 5.3. how shall I partition my disk?
I have a IEI IBX 530 unit that uses a flash disk for storage. I used a Transcend 32GB flash disk and installed CentOS 5 successfully on the unit. I now wanted to install a second unit, but am using a SanDisk Extreme IV flash disk. The installation completes successfully, but when the system reboots for the first time after the install is complete, I get an error: "Grub Loading Stage 2. Read Error". This error occurs using CentOS 5.3 and even occurred when trying Fedora 9 and 11.
why this is occuring ot how I can resolve it? I used both the 16GB and 8GB Sandisk version, and created partitions as follows:
/boot (100MB) swap (1GB) / (remainder of disk available)
Our server is a CybertronPC I2XV9080 Imperium Tower. It is equipped with a supermicro X7DVL-I Motherboard and Quad 750 GB SATA2 RAID edition hard drives in a raid 5 array. We tried to install Centos on the Raid5 array with Device-Mapper as the LVM. In the BIOS SATA Raid was enabled and the ICH RAID code base option was set to [Intel].
Intel Matrix Storage Manager Option ROM V5.6.4.1002 ESB2 RAID ID Name Level Strip Size Status Bootable 0 Raid5 Raid 5 64KB 80GB Normal Yes 1 Raid_5 Raid 5 64kB 2000GB Normal Yes[code].....
Can I have multiple level raids across the same array or would that lead to problems as above? Is the root cause of my problem the fact that intel raid5 is not supported for Linux as based on the following link http:[url]....
Is there a way to disable disk checks in a mounted usb drive? I have a 500GB usb mounted drive in my CentOS machine and everytime I reboot my system, it does disk checks which is a long painstaking process. /mnt/sdb1
I am trying to install CentOS 5.2, and the installation ran out of disk space after running for about 2 hours.I checked the FAQ, and it said 1.2 GB. The disk is 3 GB. The default install was selected, and I think that it checks for sufficient available disk space before installing. Still, it ran for quite a while before announcing that it was out of disk space.The Installation Guide is not very helpful, since there is a blank page where the disk space requirement is supposed to be. I just picked the default installation. A search of the forums on "not enough disk space" did not return much.
I'm looking for a simple solution to backup my CentOS Server (5.x) on a daily base to a mounted disk. I found the glastree tool but I have no clue if it will work on CentOS.All recommendations, tipps, hints and maybe scripts are welcome. Unfortunatelly I'm an Linux newbie and starting with Linux CentOS a couple of weeks ago
I need to read information from SUN hard disks which are about a decade old. My CentOS 5.6 mount command comes from util-linux 2.13-pre7."mount -t ufs -o ufstype=sun /dev/sdb2 /New" reports "mount: unknown filesystem type 'ufs'", though its man page describes such settings.How could I read an external UltraSCSI hard disk (yes: high pitch noise and only 9 GB capacity) on a current CentOS? Is that possible at all?
The installer can't see my raid controller (I assume) as I'm getting the following error:"Error opening /dev/mapper/isw_jbhgjgjj_Vol0: No such device or address"It just sees them as 4 individual drives: sda, sdb, sdc and sdd.Please note that I have set up the RAID 5 in the controller bios interface and the image name is Vol0, which it seems that it tries to load but for some particular reason it can't.I have also tried different bios settings and nothing worked.
My problem is that I'm trying to install CentOS 5.4 x86_64 DVD ISO on Supermicro X7SBI server with installed Adaptec RAID 3405 controller.
I created RAID 5 array and is working fine (adaptec status says Optimal) but I can't install CentOS to that array (1.5TB size).
Whenever I try to install with: linux dd
I'm asked for a driver, which I have downloaded from Adaptec site and extracted contents to USB drive (in installation found as /sba1) which has now a lot of IMG and some ISO files on it.
I try to load (I simplified names) RHEL5.img, CENTOS.img... with x64 names (one exact name: aacraid driverdisk-CentOS-x86_64.img) and I always get the error message: "No devices of the appropriate type were found on this driver disk"
This is going on for a week now and I can't find the right driver or something I'm doing wrong to get install done.
I am trying to install CentOS-DS on version 5.4 x86_64. I cannot get to the Extras repo due to lack of wired Internet access. I have wireless (except to server) and I have big UFD drives.
I need your help urgently. I will shortly install Centos 5 on a HP DL380R05 E5420 Server with two HP 146GB 10k 2.5 SAS HP SP hard disks running hardware RAID-1. I am a newbie on CentOS, please advise me:
1. Do I need a Centos RAID device driver for hardware RAID-1 on the HP DL380R05 E5420 Server? 2. Should I use Centos i386 or Centos x86_64 in this case? Which one: CentOS 5.2 or CentOS 5.3? 3. Does Centos support Embedded NC373i Multifunction Gigabit network cards?
The following is my server's hardware configuration:
HP DL380R05 E5420 2GB Base AP Server(1) Quad-Core Intel Xeon Processor E5420 Two Embedded NC373i Multifunction Gigabit / 2 GB (2 x 1 GB) PC2-5300 Fully Buffered DIMMs (DDR2-667)/HP Smart Array P400/256MB Controller /Rack (2U)/Hot Plug Fully Redundant Fans Standard Two HP 146GB 10k 2.5 SAS HP SP HDD HP 1000W IEC C14 Cord RPS Kit
I want to install CentOS from netinstall CD, but it doesn't work for wireless connection, because it just looks up for eth0 connection. Well, I connected server to wired USB connection and it's named eth1. I want to use netinstall CD but using eth1 connection. Is there any way for doing it?
I have seen that is possible to boot from a USB stick and use a USB memory as hard drive.I have a server enable to hold 6 sata drives 3.5", But I want to use the 6 drives and make a Raid-5 setup for backups 5 -1 spare. /boot cannot be on a raid-5 level 0 or 1. But I want to have redundancy for my OS, them I can install Centos on a Raid-1 using 2 disk, which let me only 4 for the raid 5. I will run a backup I want to have a lot of space.
Using 4 disk for raid-5 2 TB I will have 6TB no spare, no spare is not a good option at least I will prefer 1 spare.Well, I was thinking, the server MoBo have USB support, if I open the box I can see the small entrances, If Centos let me installed on a USB memory drive, can I trust a USB memory stick?t night with bacula.
I've just installed CentOS 5.4 on my Thinkpad T43. Everything works fine except one thing that, when I suspend the machine, the hard disk is always shut off in a "hard way". The sound is similar to the one you would hear when shutting down the machine by keeping pressing on the power button.. this is no good.
I am trying to install Centos 5.6 on a motherboard with a built in Marvel 88SE61xx drive controller.NO drive arrays are configured using the Marvel BIOS configuration utility.During the install CENTOS displays loading MARVEL_PATA driver and it waits and waits and waits.Looking on one of the system message screens I get the following types of messages:qc timeoutfailed to identifyI/O errorLink is slow to respondSRST failed errno=16ata4: reset failed - giving upAny ideas as to how to get CENTOS to recognize the drives connected to the motherboard Marvell controller on a NON-RAID configuration?
I've been trying to install the Fuppes media server onto CentOS and have had a few difficulties. I had to do a build from the source (svn build 578), then configure, make and make install. So far so good.Once I try to run fuppes, I get the error:[ERROR] Failed to bind socket to : 8.15.7.107:0.The documentation I've searched so far suggests that there is a config file that needs to be set with the appropriate ip address, but the file doesn't exist as the program hasn't started up yet!
I've Got one Problem with My Computer soon after success installation of when the boot-loader ask me to choose OS at CENTOS 5.4, multi boot boot-loader if i choose windows then computer tries to boot windows but fail and give the error message that there is a problem on reading the hard disk, But when i restart it and start with LINUX then computer start successful with no error message, now i do not know what to do cause i need to use Windows and all my programs are in windows..
I'm trying to install CentOS 5.5 on an old Pentium 4 desktop PC I have, which is not being used for much other than being a MTA, and I want to migrate this functionality onto the CentOS platform for stability (Windows is a perpetual nightmare. I partitioned a spare 20GB to experiment with, and I want to install CentOS into here to play around with first so I can move my files around between Windows and CentOS, until I'm happy all of the stuff is gone, then I can scrub the Windows partition and claim the space for CentOS.
So, I've downloaded and burned the DVD and tried to install. I start the install with no args from the main install menu, and the process goes through some probing and then comes up with the "Welcome to CentOS" menu. I go through this, and then it tries to start X Server. It fails, and falls back to text mode. I get the "Welcome to CentOS" screen again, and then proceed through it. I set my keyboard layout to UK, then this message comes up at the bottom of the screen:
"_X11TransSocketINETConnect() can't get address for localhost:6001: Temporary failure in name resolution"
then on the next line: "Cannot open display :1" If I force the install to text, by typing "linux text" at the first menu, I get about the same way through, but the install just hangs doing nothing, and no disc access to the install disc.
i am trying to get centos 5.4 installed and bootable on my 16gb flash drive, with persistent overlay using and ext3 formatted drive.i want to be able to boot into centos and be able to have all updates from yum, etc, saved when shutting down for my situation i cannot use vfat.
I am trying to clone the hard drive to a slightly smaller hard drive in the same computer, same setup.What software or commands do you use to clone the entire system and resize the partition automatically?The original HD is a little larger than the destination HD. The source partition only has about 20 GB in use and the rest is blank.
I have 2 partition, a small 100MB boot partition and another 500GB LVM partition.I can't just clone from the original disk to the new disk. (for another long reason) I need to make an image of the original disk on an external USB drive first, then move that image onto a new disk.I have tried creating an image of the whole disk with Clonezilla, but then the restoration didn't work because the target drive is smaller than the original.
I've noticed this happen with every CentOS installation I've done in the past and it's confusing me. On the software template screen select, I always select "Server" and leave the extras option unchecked, I also check "Customise now". The only things I choose are the editors (to get vi), Web server and server configuration tools (and this time also Java). I didn't select any GUI programs, yet it still installs things like X, GNOME components and also samba. Why does it do that? There no way they're needed for dependencies. Is there something I'm missing when selecting the software components? Why does it still install samba when I didn't select it from under "Servers" components? Or have I misunderstood what software selection does and it installs all those components regardless but doesn't automatically turn the services on?
My dvd is broken. I always failed to install centos from network because of wrong configuration of tftp server. I'd like to install centos from harddrive. I got a litle application named grub4dos, I try to use it but never succeded. Therefore, I have tow questions:
1. How to install Centos from / through hard drive? 2. Where should I put the Iso file of centos or centos installation files, if i use grub4dos.
What is the best way for custom partitioning. I am completely new to Linux. So i dont know what to do.I have 500 GB of disc space.I also have 3 GB RAM.I mean i don't understand the process so
1: it askes for the partition to install linux / 2: swap partition - what is it and what is it for? 3: there can be some other partitions. Will others be visible? if i create them? how are they called and what are they used for) Mb there is something such newb as me should know about it?) I can format only space used for / and other unused space i can format later when linux installed and I am more used to it. When i know what it is for?
I have a script in /etc/init.d that starts when the machine boots up, but doesn't stop when the the machine shuts down.This simple script recreates the problem. It just logs when the 'testservice' is started and stopped. When the shutdown -h now command is run, it should be called with the 'stop' parameter shouldn't it?
