Ubuntu :: Setup A Dual Monitor On System / ATI FireGL V3100 / 8.04
Mar 11, 2011
I am trying to setup a dual monitor on my system. I have gone through many posts and did the following.Downloaded EnvyNG to download relevant ATI drivers and eventually I got to a point where I can see that ATI is listed under Hardware drivers. But, from here, how do I actually set dual monitors?. I am looking for some interface like Catalyst, but couldn't find one after the drivers got installed. What am I missing here?I went back and forth, but after restarting the PC, the resolution goes to 800X640 and I have no option of setting dual monitors. I reset the options in /etc/X11/xorg.conf to let Ubuntu use the default drivers.
After a bit of work I got 3d acceleration (direct rendering) working on my system. Now, whenever I use intensive graphics, (certain screen savers, Google Earth overlay animations) all performs fine for a while (1-2 minutes) and then causes a full system freeze. Only solution at that point is a hard power reboot. I don't know where to look for a solution, since I can not check any diagnostic files when the system is frozen.
System: Intel Pentium 4 CPU 3.00GHz ATI FireGL V3100 graphics Card OpenSuse 11.4 with radeon driver.
I'm using the proprietery nvidia drivers on 11.04. I have a dual monitor setup with xinerama. The login screen appears to work fine, I can move my mouse between screens, and only one screen (right) has the login prompt. When I login, both screens show the same thing. While I can move my mouse across, I can only interact when it's on the left side.
I found this: [url], but I cannot start the display settings in the XFCE control center due to "missing randr extentions". Yesterday, I was using Kubuntu 11.04 on this same machine, and the dual monitor setup worked fine.
I am running Fedora 13 on a PC I built myself - MSI motherboard 785-E53. It has onboard DVI which my primary monitor is hooked to. I added an older 17" CRT to the onboard analog output and the main desktop with my icons and panels immediately switched to the CRT. Kernel is 2.6.34.7-66.fc13.i686, lspci -v says VGA compatible controller ATI Technologies Inc RS880 (Radeon HD 4200). How can I get flatscreen on the DVI output to be the primary?
I created a dual monitor setup in Slack 13.37 using the KDE systemsettings -> Monitor Setup function. (Sadly I had to rebuild ~/.kde in the process, but that's a different story.)
I verify that ~/.kde/share/config/krandrrc contains the new monitor setup (both screens active). I have saved a startup session with krandrtray running. However, when I logon, the system always starts with both screens in clone mode. I always have to go into systemsettings or krandrtay and redo the dual monitor configuration.
Is there a better way? Do I have to create a suitable xorg.conf (which I will try when I get home) or is there another way to boot into the dual config automatically?
I just installed Ubuntu 9.10 this evening. I have a Nvidia Geforce 8500GT video card with two monitors hooked up (one to the cards VGA, the other to the DVI). I installed Nvidia drivers and Ubuntu is working with both monitors fine.
The problem I am having is it chose the monitor plugged into VGA as the primary (uses that monitor for the toolbars) when I really want them to go on the monitor that is plugged into DVI. Is there anyway for me to switch which monitor Ubuntu treats as the primary?
I recently got a signal conversion box so I could route my netbooks monitor-out port to my TV. The idea being that I could effectively set the TV up as a separate monitor for watching movies on whilst I worked using the netbooks own monitor. It seemed to work initially, the Monitors dialog box could easily detect and setup the TV as if it were just an external monitor however I can't seem to play any kind of video on either screen when this is set up. All I get in Totem, Mplayer, VLC and skype is just a black area within the applications window. The sound works fine so this is clearly just a video problem.
It only seems to occur when I configure the system to use the TV as a separate monitor. If I tell it to display the same thing on both monitors all video output works fine.
When ever I install the (recommended) drivers through the "Additional Drivers" interface to run Unity my dual monitor setup does not work. The monitors won't even detect correctly what so ever. Then, when ever I install (more basic?) nVidia drivers through the packet manager, my dual monitors work as planned, but now Unity won't work. What's the deal? Are there any work arounds for this?
I've played around with a second monitor, but so far I haven't found a satisfying solution. I am using a laptop with a GeForce 9600M GS graphics card. I have managed to set up twinview, but my monitors don't have the same height so I'd rather have something like the "seperate x screen" option. Or how I imagine that option would be like. After some problems with the nvidia configuration tool (I couldn't change the xorg.conf, until I read this: [URL] I now have two separate screens, but the second one is all empty, with black background and X-shaped mouse cursor.
There seems to be no window manager running, I can start programs there with -display :0.1 , but they don't get any frame decoration and, which is worse, no keyboard focus. I'd be fine with a fullscreen konsole there, so I don't really need a window manager, but I do need access from the keyboard. I'd prefer a setup that would allow me to easily (without editing xorg.conf) switch between using both monitors and using only one, because I don't always use the laptop at home.
Right now, I need to use a dual-monitor setup. Be it for my casual desktop usage, or to my projects and programs presentations with a slideshow. The latter is critical and that's why I'm here.So, after some Intel Drivers update, some programs started to work nicely, faster and beautifully. But it corrupted my Dual-Monitor Setup. I don't know what to say, I'm totally desperate. I had to show one of my programs to my teacher using a projector, but with the dual monitor corruption, I called in sick today. I need to use the netbook screen to make changes on the program and the second monitor/projector to show the program working.
I'll show some pictures, but I'm without a camera right now, so I'll use one china-phone that's hanging around here to take a picture. Sorry for the quality. Both Monitors, you can see on the right of the bigger one the corruption I'm talking about.
Just installed Debian 8, coming from Ubuntu12, it seems I cannot get my dual monitors to work as it should.
I want two monitors side by side, currently I have two identical outputs. I looked around a bit and register two possible problems.
root@bigcem101-debian:/home/bigcem101# xrandr xrandr: Failed to get size of gamma for output default Screen 0: minimum 640 x 400, current 1024 x 768, maximum 1024 x 768 default connected primary 1024x768+0+0 0mm x 0mm
Hence, problem 1: it is as if there is only one monitor detected. Then I tried to look for Xorg.conf ..... and: problem 2 xorg.conf is not there. This seems to be normal but when I installed my Ubuntu years ago it was still there and one could manually set things. There must be something new I am missing.
Card: VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] RV670 [Radeon HD 3690/3850]
It seems I have both ati and radeon installed.
root@bigcem101-debian:/home/bigcem101# X -configure (EE) Fatal server error: (EE) Server is already active for display 0
I'm trying to get an external monitor hooked up to my laptop with the intention to use both simultaneously using TwinView. Actually, I'm not "trying to make it work": everything works fine, using NVIDIA X Server Settings. However, when I reboot these settings are lost and I have to manually expand my desktop again.
I've found that running NVIDIA X Server Settings as root should allow one to "Save to X Configuration File", in order to let it automatically load the right settings. When I click this option, however, I'm asked to manually provide a file name with my home folder as the default location. I'm confused how to proceed - where should I save this configuration? Or should I be taking a completely different approach in the first place? (note: KDE 'Display and Monitor' doesn't work. Only when I use the NVIDIA-thingy KDE will recognize that my desktop is expanded to a 3600x1080 resolution)
I did set up dual monitors few times on few of my boxes, with 3 video cards :
Radeon 9250 AGP (have 2 of them) - with open source ATI driver Geforce 6200 PCIE - with nouveau driver
In all cases I connect 2 LCDs. one 1440x900 or 1680x1050 to DVI and one 1280x1024 to VGA (all the cards have DVI and VGA out). The LCDs are the same ones tested with all cards :
1440x900 : Benq FP-92W 1680x1050 : Teac T2005L15 (identified as KTC2002 in xorg) 1280x1024 : Proview PQ-721KP
Tried on different boxes runnning Arch linux, different kernel / x / drivers / kde versions
Problem is - in all those setups, one monitor allways randomly blanks for a split second and comes back (incl. switching of the backlight, and displaying the "Source : VGA" or "Source : DVI" title as if it was switched off and on)
This happens randomly, but (more pronounced with the ATI cards) related to me clicking on stuff or the display changing (even if the changes are on the second screen)
With the Radeons only the monitor connected to DVI blanks. And the 2 radeons do it in different frequency, one is more often and one less
With the Geforce only the monitor connected to VGA blanks
When I test with 1 monitor (other one disabled in xorg) : Radeons sometimes still do that to DVI monitor but rare (much less than with VGA connected) (VGA monitor never blanks). Geforce does not do it at all and has problem only when 2 monitors are connected
I first thought its a hardware issue (the cards are from junk), but it happens the same with totally different hardware (exceps using same monitors) so i no longer think it is
I have the nVidia GeForce 8500 GT 512MB graphics card, I put it in my system to get a speed boost and for a dual monitor setup, I don't have the proprietary drivers installed I tried installing them, and when I did it asked for reboot, so I did, and when it came back up only one monitor was in use, and it was running very very sluggish, so I opened up the Monitors from the settings and it said to use nVidia's thing, so when I did, I enabled the second monitor, and hit apply, and it asked for a restart of Xorg, doing that came back telling me that no monitors were find, and a reboot brings me straight to tty1... I tried both the recent version and the older one, both did the same thing, I really wanna get my Compiz effects back. is there a way to get this working? I will do anything you ask if it solves the problem...
I was successful in getting the ATI catalyst software to set the displays to maximum resolution. The second display is dark. It shows a white "X" cursor if I move the mouse to the second screen. The KDE desktop configuration manager does not recognize the second monitor.
I'm trying to get dual monitors working on a fresh install of debian from the netinst install cd. I did not allow the installer to download any packages and then manually installed xorg gnome-core & gdm using apt-get.
The monitors are plugged into the onboard vga and dvi ports of my motherboard. I believe the chipset is intel.
I have activated dual screen monitors using the Nvidia driver GUI as Sax2 would not correctly configure it. Now at every boot I get the message "undefined video mode 31a, press [enter] for a list of video modes or [space] to continue. After pressing space the system boots to my liking, how can I get rid of the message at every boot up?
I am using Suse 11.2 and KDE4.3.1 My video card is an Nvidia Geforce 7100 GS I thought I was using the Nvidia drivers as I have a GUI from Nvidia in my launch menu if I search "Nvidia" and I have completed the one-click installation. Although when I go into "My Computer" it says driver unknown.
I think I have caused a big problem with my laptop running Ubuntu 9.04, and I now can't get it to load up properly at all. It was when I was trying to change the screen resolution of my external monitor.
I'll try to recall exactly what I did...
I connected the external monitor and then turned the laptop on. The laptop worked fine, and the external monitor worked fine. The only problem was that the resolution on the external monitor was poor (it was the same resolution as on the laptop screen).
I went to system>preferences>Display
I removed the tick from mirror screens
Then I selected the external monitor and changed its resolution to the maximum setting. At this point a message popped up, but now I can't remember exactly what it said - I just clicked OK.
Both screens went all black, and I couldn't undo whatever I'd done.
I've now tried switching the computer off again and on again. If the external monitor is NOT connected when I switch the computer on then the laptop doesn't load up - I get the little Ubuntu symbol to start with, but then the screen just goes black.
If the external monitor IS connected then it takes me to the screen where I get to choose which OS to boot. If I boot normally then I see the ubuntu symbol and then it goes black. If I choose recovery mode then it does some recovery and then it takes me to a command line. So I can see all of my files.
Sometimes it does something different when I switch it on and an error message appears on the laptop screen. But the screen is so fuzzy that I can't see what it says. I click on OK (I guess it says OK...) and it takes me to another error message - but I can't seem to get any further.
So that's the problem. If anyone can help me I will be very grateful. I'm actually not that intested in getting the external monitor to work - it's much more important that I undo whatever change I've made so that the laptop works properly again.
I think the important thing is that I can get to the command line, so I should be able to make any necessary change there.
I want to buy a laptop with gma 4500hd WHAT I WANT IS
1. 2D AND 3D full support eg compiz, full functional kde4+effects (not to be slow) 2. full hd support 3. oss driver 4. ability for dual head monitor setup
searching in google find out that as fa as it concern the dual head setup there is a limitation on virtual desktop for older gma cards
I've been troubleshooting a friends computer and we've pretty well hit a brick wall. The issue at hand is the video card will not output properly. To be specific, it's an NVidia card with both DVI and VGA ports. We want it to output via the VGA and ignore the DVI because there's nothing plugged in there (the monitor we want to use doesn't support DVI). At any rate, the only time we can get the VGA to work is when we have another monitor plugged into the DVI port and dual head the system. When we do this it also adds an extra "Unknown Monitor" to the display panel. When we just use the DVI the extra "monitor" disappears. now we don't want to have monitor sitting here useless just so we can use the vga out, but there seems little else to do. We tried installing the Nvidia proprietary drivers through the software manager and yum and it failed both ways.
This is really frustrating because it seems like it should be such a simple thing but nothing works. Does anyone else have similar issues? is there something i can do to fix this? I apologize if i've not provided enough info, but ask and i'll post anything you need to diagnose.
I have some trouble with my hp workstation xw4400 with an ATI FireGL 3300 and the X-Server. There was no problem with the graphical install routine and the graphical boot works fine. But when the system changes into the login-screen, then it results in a black screen and a more or less frozen system.
I want to set up grub for a dual boot system of xp and vista. The thing is that I have vista installed and would have to install it ance again after setting up XP in order to use the microsoft bootloader. And secondly I slowly want to get into linux...
This is how I tried it: I have four partitions on my HD and want to install the Bootloader on /dev/sda3. I started up the ubuntu live cd, mounted partition3, opened the console and tried this command line which I found in a tutorial
grub-install --root-directory=/media/hda3 --recheck /dev/hda However I get the following error message:
mkdir: cannot create directory '/media/hda3/boot': No such file or directory
I need some help getting my dual monitors working in Fedora 12. I've tried some things from other posts and a few things from various websites and wikis (Gentoo), but nothing I've done has worked. To be honest, I can barely remember what I've tried and what I haven't anymore, because I feel like I've gone in circles.The card has one DVI out and I'm using a DVI-splitter to connect the two monitors. This configuration works on my Windows 7 boot. Also, the second monitor is detected, but shows no display.
I have a dual monitor setup in Ubuntu, with my main monitor on the right and the monitor I want to extend to on the left monitor, but I can't seem to get it to do this, it always has the 'desktop' on the left monitor and then extends onto what I want to be my main monitor. I have an ATI Radeon 4350 Graphics card.
Is there any way to put a dual monitor wallpaper on a single monitor configuration using desktop wall? Using only 1/3 or so per wall. Something that will have the effect like the scrolling wallpaper feature on Android/iPhone.
have been trying to setup a dual boot system with ubuntu and XP running side by side on my Thinkpad T41.tried it a few times and always causes the same problem. i have 40 gig HDD, on which i create a 13 gig NTFS partition and leave the rest as free space. then install XP on the NTFS partition. no problems.
then i boot from the ubuntu disk (9.10 Karmic) and install using the "use free space" option at the partition section. ubuntu installs ok, and boots fine from GRUB 2.0. BUT when i select the XP option from GRUB's list, it starts to boot XP, i get the standard XP loading screen for three seconds and then it crashes to a blue screen critical problem, and restarts the system. when i then boot from the xp cd and go into recovery mode CHKDSK will not recognise the disk, and DISKPART shows one HDD at 35 gig which it cannot access.
this means i cant run FIXBOOT and get my xp install running again. every time i do this process it produces the same problem. tried at first with xp installed on whole HDD, and reducing the xp partition size. killed XP. then tried ubuntu first and xp second - but this caused the same inaccessible disk problem - xp would not recognise the partitions and would not install. so i slipstreamed my XP install disk to SP2 hoping this would make it recognise the partitions, but no luck there. so had to format all and repartition the 13 gig NTFS for xp. installed xp again without difficulty but ubuntu install killed my xp in the same way.
This is a triple-monitor setup with two video cards, where the mouse pointer gets "stuck" if it tries to cross from one video card to the next one. It worked correctly in openSUSE 11.2 and doesn't work in openSUSE 11.3 with the same xorg.conf. This is a 64-bit openSUSE 11.3 with xorg 7.5-11.3 (the openSUSE prepackaged version). I've already tried NVidia drivers 256.53-16.1 (the openSUSE NVidia repository version) and 260.19.12 (the latest off of the NVidia website).
This is the same xorg.conf that I used successfully in openSUSE 11.2. I tried a new automatically generated xorg.conf using nvidia-settings and it had the same problem. This forum won't let me upload the relevant files, but here: [URL] is a tar-ball with my xorg.conf, Xorg.*.log, /var/log/messages, and the NVidia debugging output.
