Ubuntu :: Mobile Broadband Slow In Lucid With Huawei E166

May 3, 2010

I seem to have a problem with my mobile broadband connection. I have a huaweii e166 usb hsdpa modem. It is veeerrryy slow. It used to work fine in karmic a few days ago, used to get 800kbps (from whatismy.com), now in Lucid the speed test does not even finish sometimes, but if I open the system monitor it shows about 1kbps. Sometimes is gets slightly faster and I can browser a bit more, but then the speed goes down again, to barely useable. I have also setup the modem in xp and whatismy.com speedtest shows 900+kbps constantly. I did a clean install of lucid on my compaq presario cq60 laptop. I have disabled ipv6 and installed the usb-modeswitch_1.1.2-2_i386.deb and usb-modeswitch-data_20100127-1_all.beb but it is still very slow.

[Code]...

View 4 Replies


ADVERTISEMENT

Fedora Networking :: Mobile Broadband Slow On (huawei E230)

Nov 22, 2009

My connection is much slower on linux than windows (I'm dualbooting so its easy to test). On speedtest.net I get 0.30Mb/s at most on linux but about 2Mb/s on windows.Torrents does not seem to be affected thou. I've got speeds up to about 150kB/s on Fedora.I'm running a fresh install of Fedora 12 64 bit.

View 4 Replies View Related

Ubuntu Networking :: Huawei Mobile Broadband On 10.4 LTS?

May 2, 2011

I am new to Linux. I have recently installed the Ubuntu 11.4 LTS Distro that comes with the Haynes Linux Manual (which I heartily recommend to new users). For the Internet I have a Huawei E1550 dongle on the 3 network in the UK which I'm currently using with Windows XP on my desktop to post this thread. After some initial fumbling, I'm unable to use the dongle with Ubuntu.

View 8 Replies View Related

Ubuntu Networking :: Huawei Mobile Broadband Not Working After Unlocking?

Jul 25, 2010

i am using ubuntu 10.04. my huawei e1550 usb mobile broadband modem was detected out of the box and was working fine . But after unlocking it with a software,the modem is detected and when i connect ,it immediately disconnects. unlocking was some 'Firmware upgrade' . I tried other distros like pclinuxOs but the same problem prevails. and it is working in windows.

View 5 Replies View Related

Ubuntu Networking :: Huawei E173 Mobile Broadband Installation

May 30, 2011

I just purchased a mobile broadband connection from 3 in Denmark. I spent three hours following guides about usb-modeswitch and such. I just couldn't get it to work. Now, finally, I've come THIS far, but yet no internet.

Code:
daniel@daniel-laptop:~$ sudo usb_modeswitch

Looking for target devices ... No devices in target mode or class found Looking for default devices ... Found default devices (1) Accessing device 004 on bus 001 ... Using endpoints 0x0f (out) and 0x8f (in)
Inquiring device details; driver will be detached ... Looking for active driver ...

OK, driver found ("usb-storage")
OK, driver "usb-storage" detached

[Code].....

View 3 Replies View Related

Hardware :: Huawei E1752 Mobile Broadband Dongle

Feb 23, 2010

Need a bit of help with this have got the broadband side working lovely on Mandriva linux but it should show as a removable drive in fact in windows it shows as two on linux none its as if there not there.Can anyone point me in rite direction to sort this.it sort of see but it just is not available normally removable drives just come up

View 1 Replies View Related

Ubuntu Networking :: Vodafone ( Huawei K3520 ) Mobile Broadband Dongle?

Feb 12, 2010

I'm new here. This is my first post. Something tells me my problem will be met with great sighs and shrugs of shoulders. I think you may have heard this problem just a few thousand times. couple of days ago i took the plunge and installed Ubuntu 9.10. I already run XP Pro. I have the system set for dual booting until i get to grips with Linux and have all that i use daily from software to hardware comprehesively installed and running. then i have this ideal romantic dream of dumping my microsoft heartache, and living a happy life with the new love in town (an OS that works!)

Vodafone (Huawei K3520) mobile broadband dongle. Yes i know its a touchy subject but i am going cross-eyed reading info on various forums from this one to the betavine forums and a detour through vodafone themselves. I just can't find clear concise info on how to get this dongle up and running with Ubuntu. My laptop is Acer Aspire 5633 WLMi. I would really really appreciate your help on this subject i need to get online with this dongle and Ubuntu.

View 9 Replies View Related

Ubuntu Networking :: Wind Mobile Huawei E181 USB Broadband Not Working?

Oct 19, 2010

I just installed 10.10 on a my new Aspire One Acer netbook and I got a mobile broadband USB stick from Wind mobile.

The stick is activated because it works on my 20 GB Windoze 7 O.S. but it doesn't work at all on my 140 GB Ubuntu O.S. Both systems are on the same machine so I know it's not a hardware problem either.

Here's what happens: I log on to Ubuntu, plug in the stick and I select the "New mobile broadband GSM connection" in the network connections menu.

From there I selected my country (Canada) and my mobile provider (Wind Mobile) than I selected my plan (Mobile Broadband) and my APN (broadband.windmobile.ca).

Then the stick blinks slowly and the network icon looks forever for a connection but no matter how long I wait no connection ever establishes. My roomate has it working on his HP laptop Ubuntu but no luck on mine. The stick just keeps blinking, a steady light indicates a connection.

View 3 Replies View Related

OpenSUSE Wireless :: Mobile Broadband HUAWEI E1756C Connect But Do Not Surf ?

Feb 20, 2011

I am trying to use the HUAWEI E1756C USB stick to connect to the internet. Installing usb_modeswitch and usb_modeswitch-data allowed networkmanager to "recognize" the stick and set up a mobile broadband connection.

The result is that NM succeeded in connecting (one of every five attempts) but firefox does not surf, nor emails can be downloaded etc. Just like if not being connected. The USB modem shows the steady blue LED as connected.

A NM issue? I have tried disabling NM control and tried with PPP clients like NMTSMON, wvdial and even Sakis3g. All with the same results. They seem to connect and show flux up and downloaded but no surfing.

resolf.conf shows is pretty much empty and no DNS there.

The working settings in Window$ are:

Same settings with Sakis3G, or NMTSMON or NM result in connection with no action from applications that use the internet.

I have had a similar issue with WLAN each time I change to a different network. I solve that by forcing to update the DHCP. I mean using -su dhcpd wlan0

But attempts like dhcpcd ttyUSB0 or dhcpcd ttyS0 get the same result. So no idea if this is an DHCP, or DNS or another issue.

My box is an ASUS EEEPC 2005H netbook with OpenSuSE 11.2 and KDE

View 2 Replies View Related

Ubuntu Networking :: Huawei E122 Mobile Broadband HSPA USB Stick - Doesn't Show Up Under Lsusb

Feb 7, 2011

I have a Huawei E122 Mobile Broadband HSPA USB Stick on three ireland. i can't get it to connect. but i think the problem might be, when i stick it in nothing happens. it doesn't show up under lsusb. i don't think it "mounts"

View 2 Replies View Related

Fedora Networking :: O2 Mobile Broadband (Huawei E169 HSDPA) - Internet Loads At The GPRS Speeds Max Of 5kb/s

Dec 26, 2009

I have a little bit of a prediciment with my Mobile Broadband dongle, even though I know I'm in a 3G area (Dongle Supports 3G connection) my internet still loads at the normal GPRS speeds max of 5kb/s. Is there anyway to change the speed of it or do I have to keep with GPRS at the moment?

View 2 Replies View Related

Fedora Networking :: Mobile Broadband FC13 Huawei E173 - Cannot Switch Device To Modem Instead Of Storage With Usb_modswitch

Nov 27, 2010

I've been trying to make my FC13 Dell d620 work with a Huawei 3G usb modem mode E173. I can not switch the device to modem instead of storage with usb_modswitch. This is what I get on lsusb:

[Code].....

View 5 Replies View Related

Ubuntu :: HUAWEI E160E Virgin Mobile No Longer Works After Upgrade To Lucid?

Jun 17, 2010

my HUAWEI E160E Virgin Mobile no longer works after upgrade to Lucid it is detected but the connection no longer works. I tried deleting the connection and trying again but the modem is not detected in network-manager. The modem was working when i was using Karmic and still works on my UNR Karmic Netbook. I have tried various methods but I have not been able to get it to work.

View 1 Replies View Related

Ubuntu Networking :: Mobile Broadband Slow Connection (SmartBro/Globe Tattoo)?

Apr 22, 2010

I have successfully configured my Mobile Broadband (USB 3G/HSDPA modem) via NetworkManager.Both SmartBro & Globe Tattoo, (these are both providers in the Philippines) connect successfully to their respective networks but my observation is the connection is slow if we are to benchmark these connections running on M$ Windows.

Is there any tweak available to enable the connection speed to improve? I know that there are other factors that affect the connection such as the signal and PC speed. I am currently using a brand new Intel Atom netbook.

View 1 Replies View Related

Ubuntu Networking :: Samsung Mobile Modem Not Detecting When Connecting New Mobile Broadband Connection?

Oct 17, 2010

i am using samsung S3310 with aircel when i am connecting new mobile broadband connection my device is not identifying ,so that i cant connect Internet.but everything okay i mean settings in mobile and pc. for same connection i used Nokia mobile its identified and Internet was connected but samsung mobile is not identifying in terminal i typed LSUSB my device is shown in that.

View 9 Replies View Related

Ubuntu Networking :: Huawei E 1550 Broadband Connection With 10.04?

May 16, 2010

I use a Huawei E 1550 mobile connection, which worked fine in Ubuntu 9.10.I've got it working okay in 10.04, having installed modeswitch. However, it will not automatically reconnect if it drops out. I can force a reconnection, only if I remove the dongle and then plug it in again. Although it shows in network manager, clicking on the list entry for the dongle, just produces a disconnected dialogue message. The only way to get it to reconnect is to remove the dongle and plug it in again.I know there have been a few posts about getting mobile dongles to work in 10.04, but I can't see any solutions to this little issue yet.

View 6 Replies View Related

Ubuntu Networking :: Connecting To Virgin Broadband (aus) Using Huawei E160e?

Jan 23, 2010

I am attempting to connect to Virgin Broadband (Australia) pre-paid using a Huawei E160e modem in Ubuntu 9.10 UNR. I have setup the connection as per [URL].. including disabling CHAP and changing the APN as required in the thread. when I try to connect using the network manager, it disconnects straight away with the message "GSM Network disconnected". When examining the logs /var/log/daemon.log, I get the following information:

Code:
Jan 23 21:26:09 janet-laptop NetworkManager: <info> Activation (ttyUSB0) starting connection 'Virgin Mobile'
Jan 23 21:26:09 janet-laptop NetworkManager: <info> (ttyUSB0): device state change: 3 -> 4 (reason 0)
Jan 23 21:26:09 janet-laptop NetworkManager: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) scheduled...
Jan 23 21:26:09 janet-laptop NetworkManager: <info> Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) started...

[Code]....

View 6 Replies View Related

Ubuntu Networking :: Mobile Internet: Huawei E 173 - Cannot Get It To Work

Apr 11, 2011

I got a Huawei E 173 mobile internet USB. But i cannot get it to work under linux, only under windows(it has a windows installer on it, in order to work).

View 2 Replies View Related

Ubuntu Networking :: Celcom Vodafone Huawei K3565-Z Broadband Setup?

Feb 19, 2010

[The configuration here is based on Celcom Malaysia's setting]

Download 3 debian files from Borneoubuntu's Blog
install ozerocdoff_0.4-2_i386.deb
install usb-modeswitch_0.9.7_i386.deb (depends on Ubuntu Ver, if not necessary don't install)
install vodafone-mobile-connect_2.1.5.01-2_all.deb
select apn setting "celcom malaysia/malaysia/contract"/OK

[Code]...

View 7 Replies View Related

Slackware :: 13 - Current Huawei E1552 HSDPA USB Wireless Broadband

Feb 24, 2010

I have Slackware 13+current as of Jan 31, 2010. Except that kernel is 2.6.29.6_smp. I brought yesterday a new Globe Tattoo prepaid kit (a wireless broadband kit -- mobile broadband service here in the Philippines) which uses Huawei E1552 HSDPA USB stick (usb modem).

I understand that they don't natively support linux but from what I've learned, they are the most linux friendly wireless broadband provider. There are few success stories about installing them on Ubuntu, Xandros, Linux Mint and OpenSuSE.

I do searched the net and found: [url]

Which says I need to compile to create a huaweiAktBbo but when run, it says 'dev' failed. (Compile succeed though).

I tried kppp but my Huawei USB stick is detected as USB storage and not as a modem, so i need to use usb_modeswitch.

I grab it from [url] and tried to download the source but it seems that SlackBuilds has not updated yet its link (and the slackbuild package). I tried to make and make install the latest source from [url] but I think I forget that switch-data and conf, anyway I have to re-download again.

Do I need libusb? Or slackware 13 already have it? (I just learn while typing this that I forgot to download the switch-data and the conf file)

Another thing, I found this: [url]

But it says I need the qt compat lib from /extra? Is it this: [url] ?

View 5 Replies View Related

Ubuntu :: Mobile Broadband In 9.10 - 10.04

Apr 23, 2010

I have read that Ubuntu 9.10 does not support Huawei EC1260 mobile broadband dongles. As a result, I am using Ubuntu 9.04 still now. How will I use it in 9.10? Or,will it be supported in 10.04 or any other later version?

View 2 Replies View Related

SUSE / Novell :: Connect To Huawei E122 Mobile Dongle?

Jun 19, 2010

Does anyone know how to connect to Huawei E122 Mobile dongle? I used to connect to E169 usb stick via umtston.

View 3 Replies View Related

Ubuntu Networking :: Doesn't Recognize Mobile Huawei Alisa Internet Dongle

Apr 2, 2011

I have just installed ubuntu 10.10 sucessfully, but it doesn't recognize my mobile huawei alisa internet dongle.

View 1 Replies View Related

Ubuntu :: Mobile Broadband Dongles ?

Feb 18, 2010

I'm looking at getting a Mobile Broadband dongle, has anyone got one of these working OK with Ubuntu and if so which network are you with.

View 7 Replies View Related

Ubuntu Networking :: How To Set 3g Or Hsdpa With Mobile Broadband

Jan 13, 2010

i have both a vodafone and 3 mobile broadband dongles. they both work out of the box, however i am only getting gprs, while i can get 3g/hsdpa using my windows box. is there any gui configuration manager or terminal commands i can use to set it to 3g/hsdpa only? im running ubuntu 9.10.

View 4 Replies View Related

Ubuntu Networking :: Mobile Broadband Can't Connect

Jan 15, 2010

Just loaded Ubuntu 9.10 on a Dell 5100, (XP finally got the bsod) I have verizon mobile broadband, all was very good until I realized I cannot connect wirelessly. The usb modem was not recognized, there is no indication of any wireless connection. There is no icon and nothing happens when the usb modem is plugged in. I have been working on this for hrs & hrs. I am a complete novice on Linux, but CompT1 A certified on PC's

View 9 Replies View Related

Ubuntu Networking :: 8.04 LTS - No Settings For Mobile Broadband

Jan 27, 2010

I have an USB (Huawei 1751) modem for mobile broadband. I had it up and running in Ubuntu 9.10 but I had to clear the computer for various reasons. I have decided to only use LTS versions so for the reinstall I have used Ubuntu 8.04 LTS. I have downloaded and installed usb_modeswitch and can see that the modes is changed to the right value. After that I wanted to add a new mobile broadband connection in the network connections wizzard - but cannot see any settings for mobile broadband. I am sure it must be possible - but where is this function hidden in version 8.04 ?

View 3 Replies View Related

Ubuntu Networking :: Unstable Mobile Broadband ?

Mar 6, 2010

I have just switched to Ubuntu from Win 7 RC. So far its been fun, learning to use terminal and all. But I have got a problem now I cannot find a solution to.

I am using 3 Mobile Broadband. The thing just worked - I plugged it in, created a new connection, modified config a little and was happily browsing.

However, it started acting out yesterday. When I boot the system with the modem plugged in, the USB stick is recignised and NetworkManager starts connecting (I have auto connect on). It then shows the "connected" message, and generally appears working fine.

On the other hand, I cannot open a single page in Firefox, it shows the default server not found page.

I used the approach Windows taught me: close, open, retry. I unmount the 3 Mobile Broadband drive, pull the modem out and reconnect it. NetworkManager then does it's job and this time everything works.

I nether had this problem in Win7 or Vista. It looks to me something goes wrong during the booting when the modem is plugged in.

View 6 Replies View Related

Ubuntu Networking :: Set Up Mobile Broadband Connection In 9.1?

Mar 6, 2010

I have bought reliance netconnect broadband+ 3.1 Mbps connection. I am provided Huawai EC1260 device to make the connection.But using ubuntu 9.1 I am not able to make the connection work. I have tested the device in windows XP and it's working fine there. I don't want to use windows and desperate to establish the connection in Ubuntu 9.1.

View 3 Replies View Related

Ubuntu Networking :: 10.04 - Use My Mobile Broadband Once - Then It Stopped

May 3, 2010

I decided to give 10.04 a shot, and upon first boot, I was able to setup and use my Rogers Rocket mobile broadband stick. When I rebooted, I found that it was in the network settings, but I was unable to connect, nor did it show up as an option in the drop-menu. I played with the terminal trying to see if anything was wrong, but everything seems normal, which is to say I don't even know what I'm looking for in regards to this type of connection.

I obviously know now that it works, I just don't know what made it stopped for the time being. I'm thinking of doing a fresh install over the current partition, and trying to work the issue from there.

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved