I am having a problem when I hook my computer up to my tv the desktop is bigger than the screen will allow. Is there a way to shrink the desktop down so that it fits within the screen? I can not find a way to do it on the tv itself... I should also add that the resolution is set to 19201080 and the video card has a vga and dvi port. I am connecting to the tv with a dvi-hdmi cable
View 2 RepliesI bought a 25 foot dvi to hdmi cable to play movies from my computer on my plasma tv. Green pixels appear on about 20% of the plasma screen; some jump around others stay in one place. I have a nvidia GeForce 7600 GT card. The nvidia restricted drivers are installed. I also tried using a mythbuntu live cd and had the same problems. Is this a problem with a bad cable, bad driver, wrong setup, or something else? How can I get rid of the green pixels?
View 3 Replies View RelatedI can not get any sound through my HDMI cable. Sound through my headphones works fine. But when I want sound to go through the HDMI and play on the monitor, there is no sound.
The HDMI cable is connected to my Radeon R9 270X graphics card.
My OS version is 8.1.
It works on Windows 8.1, so it is definitely an operating system problem.
I'm trying to connect my Xbox 360 to my Laptop via HDMI cable, so that I can use Xbox ony my laptop's screen.
I connected my Latop to my Xbox 360 by HDMI cable, but nothing happens, I was expecting the screen to auto-switch or something, so I went to the monitors GUI and tried to find settings there - unsuccessfuly.
I am running 11.04 on a new Gateway with 8 gigs of ram. It is a solo installation. The monitor is connected via an HDMI cable. Everything was great (installation running smoothly for over a month) until last night. I just installed a netgear router and was setting it up with the system to try to get Stanza on my IPAD to connect to Calibre. Anyway, i suffered a severe freeze up warranting a hard boot. I could see the drive working, ancillary drives lit up, keyboard lit up so I know the system is working. The monitor did not come on, It shows a yellow light indication no signal. It is a 28" Hansspree. I tested the monitor by hooking it to a laptop. The monitor is fine. I cannot see anything on the screen so I can't boot to repair mode or use a CD. There is no signal.
View 1 Replies View RelatedDell XPS 420: Radeon HD 4670: Philips 720p TV monitor. When booting, after the GRUB screen nothing happens until the HDMI cable is unplugged and replugged. Various ATI drivers installed. Various /etc/X11/xorg.conf used.
View 1 Replies View RelatedI went out to buy myself an nVidia G210 yesterday in order to play Quake Wars. I installed the 260.19 (latest from RPMFusion) nVidia drivers and 3D effects worked along with the game. What didn't work is the sound. I am using an HDMI cable to connect my monitor to the computer. It seems as though ALSA is not letting the digital stream through because when I play an audio file in Rhythmbox, PulseAudio Volume Control shows that the speakers are blasting music. This is strange, since nothing is coming out.
aplay -l:
Quote:
[alex@alex01 ~]$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 1: Intel [HDA Intel], device 0: ALC888 Analog [ALC888 Analog]
Subdevices: 1/1
[Code]...
I am currently employing card 2, device 3 in my PulseAudio configuration (/etc/pulse/default.pa). How can I make ALSA read the digital stream from my HDMI cable?
I have a home server that I have been running for some years and am constantly tweaking / playing with it resulting in numerous reinstalls (and upsetting the wife!). It does nothing critical but I use it mainly for:
backing up my laptop files
XBMC
ZoneMinder
Due to the number of times that I manage to break it, I have now thought about setting it up as a base system but with virtual machines looking after the seperate 'components'. The machine is an AMD Athlon 64 X2 4200+ with 2Gb RAM. First of all do you think it is powerful enough to run XBMC and ZM in seperate virtual machines? - I appreciate the more RAM the better but at the moment I am sticking to 2Gb.
I was also wondering what sort of issues may arise for the audio and video areas I will be using. XBMC currently outputs through an HDMI cable to the TV and ZM recieves video signals through a seperate video card. ( I have had my concerns in the past that there have been conflicts in the way I have set things up!). I have read a number of guides about setting a system up with virtual machines but not really found any articles about the practicalities of using such a set up at home. before I commit and spend a week pulling my hair out trying to get it all to work!
I am using ububntu 9.10,and have a cable modem internet connection. All I have is an ethernet cable given to me,and when plugged in a windows machine and fire a browser am redirected to default login page where i can login, but when i plug it into my linux machine,i cant get the same done. In network connections it doesnt shows my autoeth0, i have deleted my existing dsl settings(not autoeth0),made a new wired network,i doubt what should i put into MAC addrs field(i have put my machines mac given by lshw -c network.) What should I put in DHCP client id? Anyways when i click on network connections it says under my wired connections-device not configured properly.
View 6 Replies View RelatedHow can I connect two PCs having Ubuntu OS with network cable?Similarly how can I connect two PCs one having Ubuntu and another having WINDOWS OS?
View 3 Replies View RelatedI want connect my two Linux PCs running in 2.6 kernel via cross over cable. To do this I have done the following settings after a Google search:
In PC1
ifconfig eth0 10.10.11.16 netmask 255.255.255.0 up route add default gw 10.10.11.13 eth0 (default gateway which is ip of pc2 )
In PC2
ifconfig eth0 10.10.11.13 netmask 255.255.255.0 up route add default gw 10.10.11.16 eth0 (default gateway which is ip of pc1 )
Then i tried pinging i could not able to connect.Are these above settings enough or any thing am i missing?
For your more information
In PC1
ifconfig output
eth0 Link encap:Ethernet HWaddr 00:16:76:A1:33:37
inet addr:10.10.11.16 Bcast:10.10.11.255 Mask:255.255.255.0
inet6 addr: fe80::216:76ff:fea1:3337/64 Scope:Link
[Code].....
I am computer literate but novice in case of linux.I have installed ubuntu.Please tell me how I connect to internet using mobile.how to install cable driver for connecting with mobile.What are installation steps.which rpm is required.
View 1 Replies View RelatedI have installed ubuntu 10.6.4 in my dell inspiron laptop but my ethernet card is not working when I connect my lan cable to it. But it is working well in windows vista. How to load drivers for it.
View 3 Replies View RelatedI have a vista computer that is connected to a router via a ethernet cord. The router is connected to the internet.I have a computer installed with Debian that does not have a ethernet port in the back of it. Is there a way that I could connect my Debian computer to the internet through my vista?
View 5 Replies View RelatedI am trying to connect this cable
[url]
However, it refuses to connect properly. It previously connected, but now whenever I plug it in, nothing happens.
lsusb before:
Code:
lsusb after:
Code:
dmesg error:
Code:
From some other googling, is seemed as if removing "ehci_hcd" or "uhci_hcd" would fix it, however running the following commands does nothing, as shown below:
Code:
Is there a way to have linux connect to the network when the ethernet cable is plugged in? I'm using Gentoo Linux, and I haven't found the right setup for the conf/net that'll allow me to do that.
View 1 Replies View RelatedI have an old desktop computer that I installed Ubuntu 10.04 on. I also have a laptop with Windows 7 Pro which is connected wirelessly to the internet. The desktop does not have a wireless card and the modem is in another room. I have a spare ethernet cable, is it possible to connect the Ubuntu desktop to the internet by connecting it to the laptop with the cable? I'm not very good with computers.If this isn't possible, how would I go about connecting the desktop to the internet?
View 1 Replies View Relatedi'm having problems connecting to the internet unless i manually enter the IP info.
automatic DHCP does not work. I'm on a dual boot machine vista/ubuntu 10.04 LTS connecting to the internet through a lynksys wireless g router and a cable modem.
I have a newly set up computer with 11.4 64 bit. Intel Core i5, under Sound Configuration in YaST I have '5 Series/3400 Series Chipset High Definition Audio'and 'nVidia Corporation'I have built in speakers in my screen, connected via HDMI. I hear no sound from any source, neither via HDMI, nor via a separate sound cable connected to the sound connector on the back of the computer nor via the head phone jack on the front.
View 4 Replies View Relatedtrying to create a "local network" by directly connecting an IBM Thinkpad with Debian Linux installed on it to an Alix computer running Voyager Linux. I'm following a "how to" I found to create a music server, hence the requirement. My issue is I can't get a static IP address to be configured on the Debian machine.I've trawled the net and have found the instructions about editing the /etc/network/interfaces and have tried to do this. First I tried to get DHCP working so I could connect the Debian machine to the net and this proved successful. I edited the interfaces file to look as follows:
# The loopback network interface
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet dhcp
Then I tried adding a static IP address to the machine. As this is a network purely between two machines I made up the IP addres and used 192.168.0.1 and used a NetMask calculator to give me a NetMask of 255.255.255.254 (I told the calculator there would be 2 machines on the network). I then edited the interfaces file as follows:
# The loopback network interface
auto lo
iface lo inet loopback
[code]....
I re-booted the machine (ifdown eth0 followed by ifup eth0 keeps saying that eth0 hasn't been configured - a problem there that I don't understand), but during boot up time it failed to assign the Static IP address to eth0 and made me go into SU mode. To fix it I simply replaced the interface file with the static IP inputs with the file that had the DHCP entries (I'd made a copy of the DHCP file), and re-started the machine. Everthing came up fine. So the first question is how do I get a static IP address to be assigned to eth0 such that whenever I shut down and restart the machine the static IP address is always loaded?
The second question is around creating the network via the cross over cable. From what I've found via Google, all I should have to do is create a static IP address on the Debian machine and a static IP address on the Voyager machine. Once they're connected by the cross over cable they should see each other. Is that correct, or do I have to do anything else?
how I could file share, or make the whole Hard Drive (HDD) accessible to another computer. The two other computers I have are a Toshiba Laptop with Ethernet and USB, and a iMac Intel with Firewire, USB, and Ethernet. Putting these to use along with:
Three Ethernet Cables
Two Printer Peripheral USB Cables
The Two Computers
A 2GB Flash Drive
That is all I can think of right now. I do not want to use CDs. In a way, I would like to do a network boot. So, how do I get the whole HDD visible to the others computers (either/both) and be able to write to it? I want to put Xubuntu on it, and earse the rest of the Hard Drive. The computers getting this are the iMac G3s and the eMac G4. The eMac has 256MB RAM, 40GB HDD, and a 700MHz processor. Two iMacs have 128MB RAM, 40GB HDD, and a 600MHz Processor. The other iMac is the same as the rest but has a 500MHz processor.
Can Cat5e RJ45 connector crimper be used for Cat 6 connector because I heard cat 6 connector is different from cat 5e connector and also same question for cable tester can cat5e cable tester be used for cat 6 cable?
View 1 Replies View RelatedI'm trying to get my Sound working with HDMI-connection. Got an Nividia 8600M GT on Ubuntu 9.10. Here is what aplay -l says:
[Code]....
Here is the output of alsa-info.sh:
[url]
HDMI video out is fine, HDMI audio is a no go.
i want to connect my laptop to the lcd using hdmiI have nvidia video card 9200 gs and the driver is installedafter connecting both together nothing happens!do i have to change anything in the system or display settings?
View 8 Replies View RelatedI realise this is an issue that has been covered a lot, one way or another, but at least from what I've been able to find, most of the discussion centres around getting HDMI audio to work. However, I have problems even getting the video to work from my laptop's HDMI output.
I have an HP dv6z-se, with an ATI Mobility Radeon HD 6550 (1 Gb) video card and using F14/KDE. My problem is that when I go to System Settings/Display/Monitor, Fedora doesn't actually seem to realise my computer even has an HDMI output and only displays options for VGA and my integrated screen.
When I plug it into my LCD screen, sometimes I get a 'No Signal' message and sometimes I get garbled static and a message about unrecognised input and the frequency it's coming at.
I read elsewhere in the forum that someone was able to get video working by editing their xorg.conf file, so I went in and tried to see if I could replicate that, but none of the files in my xorg.conf.d folder had anything related to video outputs (as far as I can tell at this point).
I can't get a certain harddrive out of its mounting (screws too tight) , but I want it connected to a different computer. Is it possible to have the harddrive's powercable connected to one computer, and its SATA cable connected to another computer's motherboard? (The powercable is too short to connect it to the other computer.)
View 4 Replies View RelatedI just installed Ubuntu 9.10 and its great. However when I connect to the internet at home it shows that the connection has been established but I still cant connect to the internet. My flatmates are all able to connect. However, I am able to connect from work both wirelessly and through an ethernet cable.
View 2 Replies View RelatedSo my problem is: With internet cable I have connected to modem which support IPTV, so I can watch it, and I can't browse. With my wireless connection I browsing, and I can't watching IPTV.
I need anwser to this if can I set cable connection to only VLC (with which I can watching IPTV), and wireless connection to other programs or only Firefox?
P.S.: I'm using Ubuntu 10.04 64 bit.
I just purchased an HP Pavilion p6710f desktop with an ralink wireless n card, and 11.04 won't recognize it in 'Additional Drivers'. I can't get it to an ethernet cable, and then check for more additional drivers (did this on an old laptop), so what can I do??
View 4 Replies View Related