I have the latest version of Ubuntu installed on my Dell INSPIRON laptop with dual booting. while wi-fi activation has been done on the window OS, i need to set up wi-fi on Ubuntu as well as set the broadband connectivity with my service provider. Can someone give me detailed information how to achieve. Please note i am the first time user of Linux and is not familier with intricasies of Linux.
View 1 RepliesI am using a 3G usb stick for broadband connectivity. It works fine with windows. I have spoken to the technical support but they are unable to help me regarding its installation on Fedora 13. I have seen it work on Debian platform. The drivers are available on their website but i am having difficulty in installing them and make it work.
Below is the link for drivers download;
[URL]
how to setup a broadband connection in Centos5.. My broadband connection is over a PPPoE link
View 1 Replies View RelatedProblems with setting up mobile broadband in KDE4? Than use this instruction: openSUSE starter: Step 2. Need mobile broadband? Use the GNOME applet to make the GNOME nm-applet work under KDE. With this nm-applet I have set up mobile broadband within couple of seconds.
View 1 Replies View RelatedI have a Sprint U760 air card that apparently works under Linux. Sprint has a guide: "Wireless Mobile Broadband Setup Guide for Linux OS" that I am using to setup the air card. When I go through the procedure in the manual for "Setting Up PPP Using KPPP" the last task is to query the modem to see if Linux recognizes it. When I do the query I get a response "unable to open modem". I have tried going back through the PPP setup but still get the same response.
View 8 Replies View RelatedWife's laptop has AR5001 Wireless Adapter laptop model is Toshiba Satellite A215
Problem : Wireless networking randomly loses connectivity and can not regain connectivity, the only apparent solution is a full power down , this is not even certain to work. The card works under Windows, she hates Windows. (I love her for this) I know it's not faulty hardware , because it will work for days on end under Windows without problems.
Things I've tried : madwifi drivers (any and all versions available) : These increase stability of the signal and seem to delay the inevitable however it still happens. When using these drivers the only option is to unload them modprobe -r then reboot then remove them again and re add them. It makes no sense why this works, and if I don't remove them prior to rebooting it will not work.
ATH5K drivers : These are pretty much junk, results are unpredictable at best, sometimes it will work perfectly for a few hours, sometimes it will not work at all. Nothing is repeatable, I can't seem to force whatever condition is causing this. rfkill does not show the wifi being blocked (hard or soft), unblocking it anyway does nothing, only way to make this work and it's iffy is to fully power down wait 5-10 minutes turn it back on and it MAY decide to work.
Firmware update : Updated the Toshiba BIOS to the latest version of the firmware 2.0 no joy here either. Same issue both sets of drivers.
Tried different distros and kernels : I've tried Mint 9, 10 ,11 ; Ubuntu 10.10, 10.04 , 9.10 and 11.04 (which is currently installed) , Fedora and OpenSUSE. All are giving the same problems. I have also tried a slew of different kernels no joy from any of them (I'm not at the computer with the issue now I will post exactly what kernel versions I've used when I have access to the machine).
Another useful bit of information, the hard switch to disable/enable wifi WILL disable it but turning it back on does absolutely nothing. The hotkey does nothing at all. The bios does not have an option to disable or enable the wireless card.
I will also post the typical lsmod , lspci , iwconfig all that good stuff when I get back to the computer in question. I'm probably just going to buy a PC card for it and give up on that one, but this is driving me insane and I would really like to see it resolved even if I do replace the hardware.
I use a laptop with a built-in WiFi card (Intel PRO/Wireless 3945ABG [Golan] using iwl3945 module). It's OK but sometimes is not very stable, occasionaly it simply dies and I have to reboot. It was even worse but I improved it by applying a new driver.I also have a very nice USB WiFi card (D-Link System DWA-140 802.11n Adapter [ralink rt2870]). It's much better and faster.
So the problem is that in Ubuntu 9.10 (2.6.31) I can use only the built-in one. The other one (D-Link) also works but I can't make it connect to my router. The built-in card connects to it but the D-Link even does not list it among possible connections (but it lists other possible connections which I do not want to use).The funny bit is that this problem disappears when I use an old Kernel (2.6.28-18 ) : both cards work fine and can connect to the router at the same time (obtaining different ip's). I then disable the built-in one and happily use the external card.
Unfortunately the old Kernel has issues with sound and video, so I would like to use the latest Kernel with the external card. I tried WICD but it didn't change anything.I can add that under the old Kernel the USB card is used as a ra0 device while the new Kernel lists it as wlan1.
I have an issue with my Dlink DWA 547 802.11n PCI adapter, I'm under LUCID fully updated.I have no trouble connecting to any wireless but after a few minutes I'm loosing the connectivity strenght (getting ping reply from my router that vary from 2ms to 200ms). But as soon as I'm rescanning the network using the command (sudo iwlist wlan0 scan) everything is fine (constant 1-2ms ping). I'm using wicd as network manager. I have tried to schedule a job in crontab to launch every 10min a network scan command, but didn't succeed to have it working, morehover I don't think that's the good way.
View 2 Replies View RelatedI have an older Gateway with model number: 4024GZ, and I just installed Ubuntu on it and I am not able to connect to my home's wireless network. I am assuming that this is because of a driver issue, whether there is none or the old driver isn't compatible. So is there a website that I can go to to maybe find a driver that will work with both my wireless card and ubuntu? My wirless network adapter is internal and is a Broadcomm I believe. (btw I am a beginner here and if I have posted this in the wrong section,
View 6 Replies View RelatedI am using both win 7 and ubuntu using grub. If I connect to internet in ubuntu its working fine
but if I connect to net using win 7 internet is not working. However if I connect internet in ubuntu and restart win 7 without switching off router I can access net in win7 even if I switch off router and start again its working fine. But when I shut down system and router and switch on in win7 its not connection.
I don't have any idea where to place the "mysql-connector-java-3.1.14-bin.jar" file in ubuntu 9.10. Yesterday I did this in xp successfully by placing this jar file at following locations
Javajre1.6.0_06lib
Javajre1.6.0_06libext
Moreover, the jar file which I am using for xp; can be used for ubuntu 9.10 or not. I am using NetbeansIDE 6.7.1 (installed from Software Center), MySQL 5 Server (sudo apt-get install mysql-server) is this enough?
I've been trying to use the wireless adapter that came shipped with my computer for a while now (it is NOT a USB adapter; it seems built into the computer). However, I can't seem to get it working.HP says that the driver is Lite-On USB Wireless 802.11 b/g Adaptor. I am currently connecting to the internet with my netgear USB adapter (I think the driver is something like prism_usb)
View 3 Replies View RelatedI just installed Ubuntu 10.04 as a dual boot with Win/XP, using the text based installer. Installation seems to have completed OK and Ubuntu boots as expected - but Firefox cannot find any web-page.
How do I start look for the problem cause?
I should say that I previously had installed Kubuntu 10.04 (64 -bit). It was installed for a few months up to May 2010, but then it suddenly lost all internet connectivity after I hibernated the system. Win/XP continued to work with no error. Despite some months of help and advice from the Kubuntu forum, I was unsable to solve the problem. Indeed one piece of advice resulted in the overwriting of my Win/XP installation. I have now re-installed Win/Xp and decided to install 32-Bit Ubuntu - but I am back into the 'no internet connection' problem again. Win/XP works fine.
I can see the network shares, but when I click on one of them, I get the message:Unable to mount location (header)Failed to retrieve share list from server (body)This worked fine for me in the previous versions, so I don't know what to try.On the windows machine, the share can also be seen but not permitted to connect.
View 1 Replies View RelatedThe internet has been working happily on my Mythbuntu machine for many months but stopped working overnight.If I try to do "sudo start networking" I get a "Job failed to start" message.There's also a solid orange light on the ethernet socket.As it's been working for months, I don't think my interfaces config needs updating.Looking at what's been updated recently on the system:
1) I've configured the machine to wake from USB. It was working for a couple of days so I don't believe this is the issue.
2) I set up wake-on-lan with ethtool. Again, this was working (although it did seem to disable wake-on-usb and required a reboot to fix)
3) Update to 11.04 - I said no to this, as 10.10 was working very nicely indeed.
I've disabled wake on lan and rebooted. No joy.
ethtool detects the ethernet controller ok and it's listed in lshw.
I am new to linux. I just installed linux on my PC and wanted to configure wireless network connections. I have entered SSID and mode is set to infrastructure. I don't know what is BSSID do I need to enter MAC address (of router?)?I need to connect to internet wireless can you please guide me ?
View 1 Replies View RelatedI have a Air-CB21AG-A-k9 cisco Card and trying to run it with Ubuntu 11.04. But this card doesnt seems to be plug n play device with ubuntu 11.04. As soon I inserted the card both the leds are flickering but no wireless conectivity.
View 9 Replies View RelatedI've just installed Ubuntu Desktop and connected the ethernet cable, but I don't have network connectivity. Why?
View 7 Replies View RelatedI've tried to set up an easy PXE server to set up ubuntu on various PC's via network. When I was finished I tried to boot a virtual mashine and later a normal notebook, both had the same problems, they find the TFTP server start booting and installing but it always fail. Reason: they get no IP from the DHCP-Server (I'm using dhcp3-server), even if I enter an IP manually I only get to the mirrow step where it tells me bad mirrow and the dhcp log says: Abandoning IP address 192.168.1.46: declined. I also rebootet the router but nothing changed.
View 3 Replies View RelatedI have some boxes and laptops connected to the same lan. While messing around with xorg.conf and doing a couple of restarts, one of the boxes suddenly lost internet access.The other machines can ping each other and access the internet (the boxes through eth0 and the laptops through wlan0). That one box, however, cannot ping the others, nor the router. Both ends of the internet cable are plugged in, and there are the usual continuous green and orange lights on the box end, telling me that everything is fine with the hardware connection.ifconfig gives me:
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask: 255.0.0.0
inet6 addr: ::1/128 Scope:Host
[code]..
I have no idea what happened, since the lights indicate it is not a hardware problem. It must be a problem with that particular machine, since the others are fine. However, I have not changed any of the network config files.
I had my desktop running ubuntu 10.10 at my sisters house hooked up to a router sharing internet with her boyfriend never had a problem with it there. I moved into my own apartment this week plugged the cable modem directly into the broadcom ethernet card and couldn't get an ip or anything it wouldn't connect period so I ended up hooking it up usb which works but only at speeds of 5-7mbit when I have 15mbit connection. So I put another ethernet card in hoping it was just problem with the card and tried it that worked.
I got a connection but it was incredibly slow like getting maybe 5k a second so I open network tools in administration menu and start pinging google. While I'm waiting on a bandwidth test to complete and it takes off getting like 20mbit keeps that connection for a while then out of nowhere just drops to almost nothing. Again for a few minutes then falls off completely so I restart and it does the exact same thing starts off slow then something clicks and it works great for 5 min then nothing?
I have a Toshiba Satellite L55 S5105 Laptop with "Atheros AR8152 PCI-E fast ethernet controller"
and "Realtek RT8188CE Wireless LAN 802.11n PCI-E "
I have ubuntu9.10 running on this[dual boot].
For some reason there is no wifi and ethernet connectivity.
Are the drivers not installed? where and how do I start to troubleshoot this problem.
I'm running Lucid Alpha 1. Installed it about two weeks ago. Until a few days ago, the wireless networking was the best I've witnessed on any o.s. However, after last Wednesday's updates, connectivity now lags about 10-30 seconds whenever I open any web-page or access the repositories via aptitude. Granted after it gets going, it's fine. I noticed this same behavior in 9.10. I tested my XP connection and found no problems. .
View 3 Replies View RelatedI recently formatted an old Dell D600 and installed 9.10 on a single partition. It connects to my Airport just fine hardwired, but I have had no success getting the IntelPro/Wireless 2200BG card to talk wireless. I've entered the SSID and WPA2 security ID with no success.
View 2 Replies View RelatedLately, my internet connection stops for several minutes and then re-connects. Since there are few issues to debug here (router, modem, ADSL, internet provider), I would like first to measure the failure rate. Is there a utility or script that will do the following: Wake every 1-2 minutes, verify a certain web page is available (doesn't matter which). If it fails: dump a line to a log file and get back to sleep. If OK - get back to sleep. Is there such a utility?
View 4 Replies View RelatedI have an iphone, I am trying to get internet connectivity to that phone through wifi. I dont have a wifi router. But i do have a laptop with wifi card. I am connecting to internet via cable modem. In win7 I used to create an accesspoint and do the ics from ethernet card to share via wifi card. It used to work perfectly.
Now as I am sing ubuntu, i want to do the same. I have intalled firestarter, and shared the internet connection through wifi card(wlan0).After this I created an accesspoint using the gnome network applet. Now i can connect my ifone to ths accesspoint. But there is no internet connectivity in my fone.
Every time I reboot my server, it no longer connects to the internet. It is dual-homed with an internal and an external interface. Both come up. The internal connection works fine. Nothing happens on the external interface. Ifconfig shows that both interfaces are setup correctly. My iptables settings are properly restored. Forwarding is automatically enabled. For some reason packets do not go anywhere on the external interface. This has been true ever since the upgrade to jaunty I think (now running lucid).
Once I restart the external interface it works perfectly (eg ifdown eth1; ifup eth1 or /etc/init.d/networking restart). The problem only occurs after a reboot and only occurs on the external interface.
Here's my /etc/network/interfaces file:
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
auto eth0
iface eth0 inet static
[Code]...
Trying to get the wired nic working so I can troubleshoot the wireless. I cannot get any kind of network activity. Been searching so I will post a little information that seems to be common with my situation.
lshw -C network
reveals:
WARNING: you should run this program as super-user.
*-network DISABLED
description: Ethernet interface
product: 82562EZ 10/100 Ethernet Controller
vendor: Intel Corporation
[code]....
Anyone have success setting up either wireless or ethernet connectivity on a Macbook Pro 5,5 on the 10.10 Maverick install? Normally in the past with 10.04, etc... I just plug in my ethernet cable and update my wireless using "sudo apt-get install bcmwl-kernel-source", but I can't even get my ethernet to work. I tried to load it from the live CD once logged in but couldn't figure it out.
View 9 Replies View RelatedI just installed Ubuntu 10.10. I was using iBall N 150M USB adapter for internet connection with Windows XP. Let me explain about the present Windows connection :
I am using an Outdoor CPE Wimax. For mobility purpose I have connected this wimax to one LAN port of ADSL+ WiFi router ( Beetel 450 TC1 ). This ADSL+wifi router reset to Factosy settings and enabled DHCP. With this setting , I am perfectly able to connect my laptop to Internet.
When I connect my USB adapter to Ubuntu , intially it detected the signal and asked for credentials. I gave the same and network established. But I am not able to browse the net. If I give [URL]..., its going to the ADSL+Wifi's diagnosis page. With Windows , [URL]... was going to the Wimax modem. After 2-3 trial and error , now Ubuntu also not able to connect to the wifi network.