Ubuntu :: Not Getting Network Connectivity Via Ethernet Cable?
Jul 14, 2011I've just installed Ubuntu Desktop and connected the ethernet cable, but I don't have network connectivity. Why?
View 7 Replies
ADVERTISEMENT
OpenSUSE Network :: Create Network Bridge / Device Hooked Up Via Ethernet Had No Internet Connectivity?
Feb 25, 2011I'm on opensuse 11.4 (11.3 won't work with my monitor).
My computer gets internet through wireless and I want to share that internet through its ethernet port. So far I've tried using Knetworkmanager to create a network bridge between my wireless and wired connections. I created a new wired connection and shared it using the ip address settings. I was able to get both connections active, but the device hooked up via ethernet had no internet connectivity.
I also tried this command:
echo 1 > /proc/sys/net/ipv4/ip_forward
but another test resulted in the same fashion (no internet on wired). I believe anything I add to /proc should have an immediate effect, correct?
Ubuntu Servers :: Plugged In The Ethernet - No Network Connectivity?
Jul 14, 2011I just installed Ubuntu Server, plugged in the ethernet cable, and there is no network connectivity.
View 2 Replies View RelatedOpenSUSE Network :: Internet By WiFi While Using Ethernet Cable ?
Jul 27, 2010My WiFi can connect to internet without any problem, until I plug my ethernet cable ...then I lose internet.
So the question is : how do I configure my ip/dns and stuff to still have internet when I'm plugged by cable at the same time! it was working on windows ;-)
Networking :: Ethernet Cable And Wireless Network Won't Work In Ubuntu 9.10 / Sort It?
Feb 20, 2010I'm a new user of Ubuntu, so i'm not that familiar with this OS. My wireless network is detected but when I'm entering my 128 bits WEP key, it doesn't connect at all. I have no clue where to start troubleshooting.
Here's some of my specs if that's of any help:
Computer is a Sony Vaio laptop model VGN-SZ370P
My wireless card is from Intel Corporation 82801G (ICH7 Family) USB UHCI Controller
The ethernet cable connection used to work before, but I fooled around with some commands and now seems to be disabled...
Ubuntu / Apple :: EMac And IMac File Sharing With Ethernet Cable And Other Cable?
Oct 12, 2010how I could file share, or make the whole Hard Drive (HDD) accessible to another computer. The two other computers I have are a Toshiba Laptop with Ethernet and USB, and a iMac Intel with Firewire, USB, and Ethernet. Putting these to use along with:
Three Ethernet Cables
Two Printer Peripheral USB Cables
The Two Computers
A 2GB Flash Drive
That is all I can think of right now. I do not want to use CDs. In a way, I would like to do a network boot. So, how do I get the whole HDD visible to the others computers (either/both) and be able to write to it? I want to put Xubuntu on it, and earse the rest of the Hard Drive. The computers getting this are the iMac G3s and the eMac G4. The eMac has 256MB RAM, 40GB HDD, and a 700MHz processor. Two iMacs have 128MB RAM, 40GB HDD, and a 600MHz Processor. The other iMac is the same as the rest but has a 500MHz processor.
Debian Installation :: Network Autoconfig Failed Even With Ethernet Cable
Jan 1, 2015Router works fine, debian refuses to work with it. I continued the install anyway but only have the first DVD so now I've got a useless base install that can't connect to the internet.
The fact that this installer has utterly failed where the others succeeded had drastically reduced my confidence in the debian team.
OpenSUSE Network :: Able To Connect To Networks (both With An Ethernet Cable And Wireless) Don't Have Internet Access?
Mar 2, 2011Just today I installed opensuse 11.3 on my Compaq CQ61. Even though I am able to connect to networks (both with an ethernet cable and wireless) I don't have internet access. I have used opensuse for a very brief period in the past and I had no such problem.
View 3 Replies View RelatedGeneral :: No Wifi And Ethernet Connectivity On Ubuntu 9.10 / Get Those?
Jan 4, 2011I have a Toshiba Satellite L55 S5105 Laptop with "Atheros AR8152 PCI-E fast ethernet controller"
and "Realtek RT8188CE Wireless LAN 802.11n PCI-E "
I have ubuntu9.10 running on this[dual boot].
For some reason there is no wifi and ethernet connectivity.
Are the drivers not installed? where and how do I start to troubleshoot this problem.
Ubuntu :: Can't Get It To Ethernet Cable
Jun 1, 2011I just purchased an HP Pavilion p6710f desktop with an ralink wireless n card, and 11.04 won't recognize it in 'Additional Drivers'. I can't get it to an ethernet cable, and then check for more additional drivers (did this on an old laptop), so what can I do??
View 4 Replies View RelatedUbuntu :: No Ethernet Cable - Means Frozen ?
May 24, 2011I installed Ubuntu 11.04 on my girlfriends laptop a couple days ago...had the Ethernet cable plugged in to do the install...loaded fine the first time after the install. Unplugged the Ethernet cable when I had the wireless network set up and it froze. Restarted and it wouldn't even load the desktop. Didn't make the connection at first...thought there was something wrong with Unity. After about a day and a half worth of searching Unity problems/desktop freezing and solutions, I stumbled across this:
Quote:
Do you have a Broadcom card? You have probably noticed the desktop works when you run Ethernet but it locks up when your wireless connection is active.
You'll need to upgrade the kernel to fix the issue. 2.6.39.0 did it for me.
11.04 just runs fine now.
This solution was to update the kernel, but that didn't work for me. Now I'm stuck.
Ubuntu :: 9.10 - No Internet Connection Via Ethernet Cable
Mar 9, 2010I just built my first pc, installed ubuntu 9.10 and tried connecting to the net through my ethernet cable and all that happens is it says cannot find server. Do I need to install network settings & if so what & where,or should it automatically detect them? As this is my first build I am a novice but am willing to listen & learn.
View 3 Replies View RelatedRed Hat / Fedora :: Dell N7010 Ethernet Connectivity (13 X86_64)
Oct 25, 2010There is no Ethernet (or wireless) connectivity for my new Dell N7010 with Fedora 13 64-bit. The drivers do not appear to be installed. Right now, the goal is to get the Ethernet controller (Atheros Communications AR8152 v1.1 Fast Ethernet) running. I have tried to install the AR81Family-linux-v1.0.1.13, but the tarball gives an error when attempting to extract it:
"tar: Child returned status 2
tar: Exiting with failure status due to previous errors"
I also tried the compat-wireless-2.6 which also gave errors when trying to do a make:
"make: *** /lib/modules/2.6.33.3-85.fc13.x86_64/build: No such file or directory. Stop.
make: *** [modules] Error 2"
here are the specific things MikeTbob requested be run (via his "wireless setup" link):
[Ron AT localhost ~]$ uname -r
2.6.33.3-85.fc13.x86_64
and the files lspci.txt, dmesg.txt and lsmod.txt are attached. Note that the command dmesg | grep firmware returned nothing. Also please note the website didn't like the dmesg.txt filesize, it was broken up into 4 separate files: dmesg1of4.txt, dmesg2of4.txt and dmesg3of4.txt<<< hit max file upload, so dmesg4of4.txt is in the reply to this post.
Ubuntu Networking :: No Connection With 75ft Ethernet Cable?
Sep 21, 2010I am trying to run a cable from my wireless router over a 75ft cat6 cable to my bedroom. I don't get any connection on my end and I don't have any other ideas. I did setup a m0n0wall box just to try. I got the network led on my server to light up in my room but nothing more than that. Lastly, I tried adding a 5 port switch in my room and then connecting that to my server and nada.
View 4 Replies View RelatedUbuntu Networking :: 10.4 - Connect To The Internet Via An Ethernet Cable
Jul 13, 2011I am using Ubuntu Server version 10.4, and am trying to connect to the internet via an ethernet cable. This may and probably is incredibly simple, however, I could not find anything that pertains to it.
View 9 Replies View RelatedUbuntu :: Ethernet Card Not Working On Connecting LAN Cable
Jun 29, 2010I have installed ubuntu 10.6.4 in my dell inspiron laptop but my ethernet card is not working when I connect my lan cable to it. But it is working well in windows vista. How to load drivers for it.
View 3 Replies View RelatedUbuntu :: When Ethernet Cable Is Plugged In / It Doesnt Work
Jan 27, 2011When the ethernet cable is plugged in, it doesnt work. I have to unplug the cable, refresh the page and let it wait for the connection, after a second or two, i plug it back in, and it works. this works only for that page, which means only that page loads.. if i try to open another site or smthing else, it doesnt work and i have to repeat the exercise for the new site..i have to unplug, refresh and let it wait for connection and plug it back in.. The same thing happens if i try to download an application.. i have to first issue the command to download, and when it says "connecting to blah blah.." i plug the cable back in and it starts downloading, it doesnt work if the cable is already plugged it..!
View 9 Replies View RelatedCentOS 5 Hardware :: Connect Pc To Pc With Ethernet Cable?
Jan 6, 2011i have two PC (one laptop and other desktop) how to connect both with lan cable?
View 1 Replies View RelatedUbuntu Networking :: Ethernet Cable Modem Can't Connect To Internet
May 4, 2011I am using a cable modem wired to my PC via ethernet. My ISP is Road Runner, through Time Warner Cable.
I entered my IP address, Netmask, and DNS Servers into the network, not using DHCP. This was how I was able to achieve a network connection.
I am connected to the modem, but I cannot get internet.
Here are my stats:
General :: How To Conect To Intrenet Ubuntu 6.06 Version Via Ethernet Cable
Apr 28, 2011I want to know how to conect to intrenet ubuntu 6.06 version via ethernet cable and wireless through modem THOMSON99BC4C on asus notebook.
View 3 Replies View RelatedNetworking :: File Transfer Using Ethernet Cross Over Cable?
Apr 18, 2010I am running Ubuntu Linux 9.10 on my laptop and desktop. I would like to transfer files from one to the other using an Ethernet Cross Over Cable. Is there software already installed in the bundle, that would allow me to setup network drives for each machine when the cable is connected. Also how would I setup the configuration.
View 10 Replies View RelatedNetworking :: Find A MAC Of Hardware Attached Via Ethernet Cable?
Apr 19, 2011How can I find a MAC of hardware attached via ethernet cable? I have been working nicely with an industrial scanner that is controlled by a Linux PC via an ethernet cable, but the hard drive has died I need to get it working again. The problem is that the main PCB has a Realtek RTL8019AS ethernet controller chip: [URL] which I believe is used in the most basic way possible, applied straight off-the-shelf and unconfigured. To utilise the chip ARP commands are used to assign an IP address to the chips MAC address e.g. something like:
arp -s 192.168.2.5 00-05-a4-00-a8-f8
Unfortunately the actual MAC address was lost along with the HD Th only thing I could have a reasonable guess at is that the chip will have a default subnet of 255.255.0.0 or 255.255.255.0
Networking :: Shared Connection With Playstation 3 - Put Ethernet Cable Between Them
May 2, 2011How do I make share internet connection with playstation 3 with Linux Mint? I have put ethernet cable between them.
View 1 Replies View RelatedProgramming :: Write A Program In C To Detect The Ethernet Cable?
Mar 11, 2009write a C program to detect whether the Ethernet cable is plugged or unplugged. I found out by using a command "nm-tool" in Linux terminal will show me whether a Ethernet cable is plugged or not. If Ethernet cable is plugged, in the device part of eth0, the Hardware Link of Wired Settings will indicate a "yes" and "no" if no Ethernet cable. Hence, in my previous code, I use one function called popen to read the state as shown below:
PHP Code:
[code]....
However, now my project wish to not use the NetworkManager (where the "nm-tool" command comes from). And this gives me trouble to detect the Ethernet cable. So is there any other method for me to detect the Ethernet cable in C programming?
Ubuntu Networking :: Ethernet Connection Does Not Come Back If Cable Had Been Manually Disconnected
Jan 28, 2011OS: Maverick Ethernet driver: tested with sky2 an sk98lin This has been driving me crazy for the last few months: if I unplug ethernet cable while my laptop is on reconnecting it sometimes does not bring the connection back.
And once ethernet is gone nothing that I try seems to consistently bring it back. Rebooting, disabling/enabling the driver, disabling/enabling NIC in BIOS, changing driver from sky2 to sk98lin, deleting connection from Network Manager, resetting the router - nothing helps. It seems to come back randomly a few weeks later. Once I used live Ubuntu on a USB stick and ethernet came back not only on a live distro but then when I rebooted also on my main OS. But when I tried that trick next time ethernet was missing in the live distro as well.
Also once I was able to revive ethernet but compiling sk98lin driver, blacklisting sky2 and rebooting. Of course next time doing the same routine did not help. The thing is - ethernet works fine with either sky2 or sk98lin and I can unplug the cable and plug it back in most of the time without any issues. But then every so often - bang and I'm stuck with only wireless until ethernet suddenly starts working again.
Debian Configuration :: Wireless Only Works When Ethernet Cable Is Plugged In?
Jul 9, 2011I have a debian-powered NAS (Buffalo LinkStation) and I want to configure the following behaviour: When ethernet (eth0) is plugged in, connect and get a static ip address (ie. 192.168.0.11) When a wireless usb-adapter (wlan0) is plugged in, connect to a wireless router (ie. "Ankkanet") get another static ip address (192.168.0.12)
My /etc/network/interfaces :
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet static
[code]....
what could be causing wireless to disconnect when ethernet cable is unplugged?
Debian Hardware :: Finding Plugin Names Of The Ethernet Cable?
Mar 2, 2010if i would know the terms i could search for it, so bare with my words: i got an old PC, and my ethernet-cables don't fit into its plug (port?). its a little smaller than the usual one. how is it called and what am i looking for (whats the name of the plugs which need to fit, whats the measure. all i could see is male/male and some voodoo stuff like RJ333 <-wrong.
View 6 Replies View RelatedFedora Networking :: Finding Out If Cable Removed From Ethernet Connector
Feb 2, 2009How can I find out programmatically if a cable has been removed from an ethernet connector where the interface is "up" ??? Without using ping of course.
Sidebar question, if I have two interfaces on the subnet how can I force a ping out a specific interface? Say, I have 192.168.5.14 and 192.168.5.13 and I want to throw a ping out *.13 and not *.14 ..
Ubuntu Networking :: Auto Eht0 Doesn't Work - Can't Connect With Ethernet Cable?
Nov 13, 2010I've recently bought a recycled computer for my office. The plan was to get an old cheap computer and use it to write LaTex documents but nothing else. However, I can't seem to get the thing to connect to the internet. I'm on a University network which has a funny setup but I don't think that's the problem.So here's the deal. I have tried this with 9.04, 10.04 and 10.10 and it hasn't worked. The computer recognizes the ethernet cable. If I issue the command "sudo mii-tool eth0" and get back "eth0: negotiated 100baseTx-FD, link ok". However, click on the networking logo on the top right, and click auto eth0, it tries to connect for about 30 seconds, then gives up. Unfortunately I'm pretty clueless when it comes to networking so I have no idea what to do to try to fix this.
View 8 Replies View RelatedFedora Installation :: Install The Broadcom STA Drivers From The Live CD Without Using An Ethernet Cable?
Aug 3, 2011Since there is no "Additional Drivers" app in Fedora like there is in Ubuntu, how the heck can I install the Broadcom STA drivers from the Live CD without using an Ethernet cable? And how the heck can I ensure that they stay installed, even after installing Fedora? I suppose putting the RPM on a USB Flash Drive will work, but that's the only thing I can think of... And is there an RPM out there for this specific driver?
View 8 Replies View Related