On some but not all of the apps listed on the Ubuntu Software Center, I can see the app and select it, but after I click the arrow that points right that should take me to the screen that describes it and allows me to install it is blank. The tabs at the top say that I am at the right window but nothing is there. Is there a way I can make that work?
View 1 RepliesI just did a fresh install of natty, installed a few programs along with the ati catalyst control center.
I am having serious login issues, here is what I do:
I am at the login screen right from start-up, type in username and passward and hit enter, screen goes blank, it appears I am logging in, ubuntu plays a sound and puts me back at the login screen. I do not get an "Authentication Failed" error like I would expect. Unable to login as myself or as root.
However, I am able to login if I select the "safe mode," I am not able to login under the normal mode or the ubuntu classic modes.
I suspect that this issue has to do with the ati proprietary drivers, after playing with the settings for a while in safe mode I am now able to login to the normal natty mode without any apparent issues.
Here is what I changed in ati catalyst control center to boot into natty mode:
I disabled the Xinerama and Tear Free options.
Under the 3D settings, I selected the "override application setting" for all the 3D settings I could.
I believe I still have some display issues as I am unable to drag windows from one display to another, my mouse is able to move just fine across displays though.
I also found that enabling Xinerama prevented me from logging into the ubuntu and ubuntu classic modes, but I was able to login to the ubuntu with no effects mode.
So after I went to OMG ubuntu site and downloaded "complex shutdown" since it looked useful and I needed it I installed it..but it doesnt seem to start up for some reason so when I went to uninstall it software center went "blank" just a grey screen with the black toolbar
View 2 Replies View RelatedI am having the same problem, as soon as X tries to load my screen just goes blank. I have an ATI Radeon 9550. At first I tried switching between VGA and DVI as well but upon ruling that out, I switch to my on-board video card and that is working thus far, but I'm trying very hard to figure out a way to be able to switch back. Anyways I'll check back in later on if I have any new information I will post.
View 3 Replies View RelatedOk well this is my first post on the ubuntu forums and the problem I have is, hopefully, pretty simple to fix. When I am installing Ubuntu, I go through all of the steps and once it asks where to install and partitioning and all that I tell it to erase the entire windows thing and put in Ubuntu. So I click the Forward button and when it gets to 69% of copying files, the screen goes black. It sounds like its still running the install but I cant be sure. What should I do?
View 1 Replies View RelatedI've found similar posts to this but none seemed to be solved. I'm trying to install ubuntu 9.10 on my new laptop. Dual boot Win 7 Pro on first partition.Its a gateway nv79 laptop with an intel i3 330M processor.The problem occurs when I boot from the CD I get the first menu where you can choose to install, load ubuntu from CD, etc. No matter which option I choose, I get nothing but a blank screen. Then I can do nothing but power down by holding the power button.I've tried both 64 and 32 bit versions, same thing. The 32 bit disk works fine on another computer. I've also tried booting another version of Linux, Helix, from CD and that also works fine. I'm thinking ubuntu doesnt support my graphics card: Intel Graphics Media Accelerator HD
View 1 Replies View RelatedI've searched the forums and all the problems seem to be getting a blank screen after the first menu or first splash screen.My problem is that I'm getting a blank screen straight away without seeing anything. As soon as the system says that it's booting from CD the screen goes blank and nothing happens.I've done the md5sum on the disc successfully (and the iso). It's an old system (P4) and I'm using the integrated graphics.I've tried Ubuntu Server 10.04, UNE 10.04 and Ubuntu 9.04, all have the same problem.
View 1 Replies View RelatedI'm installing Ubuntu 10.10 64bit (and ive tried 32bit) on a brand new Sony Vaio as a dual boot on Windows 7.
All goes well and I eventually get to the desktop on Ubuntu but the screen isnt right. Its not so much the resolution as its perfect in clarity but its the physical borders right and bottom are out of screen. Move the mouse to the right and bottom and the mouse disappears. I cant see the bottom bar at all. But like I said, the res clarity is perfect. I've tried playing with the res but it wont change the border issue.
Soon enough, on the top right, I get a hardware driver update alert for a Nvidia and asks me to activate. I do this with the hope to fix my screen size issue. Once activated, I restart and thats it, I get a blank screen.
This is what ive tried:
In recovery mode, i can get in with low-graphics.
Uninstalled the Ubuntu recommended Nvidia driver and all is ok.
Tried downloaded the correct Nvidia driver for my laptop but exact same.
In low graphics mode, when I launch Nvidia X Server, I get this error: 'You do not appear to be using the Nvidia X driver. Please edit your X configuration file (just run 'nvidia-xconfig' as root), and restart X server.'
After selecting "Install Ubuntu", the screen goes blank and nothing happens. I am using a HP laptop and am trying to install Ubuntu 9.10 from a CD I ordered from ubuntu site.
View 9 Replies View RelatedI recently tried to upgrade my openSuSe 11.1 system using the instructions at:
SDB:System upgrade - openSUSE
I successfully got the system to 11.2, but the upgrade from 11.2->11.3 went awry. The installation froze during the update, and I had to start it over. The first issue I had to deal with was the fact that rpm had been upgraded and zypper hadn't, so zypper wouldn't function because older rpm files that it would search for had been deleted. After rolling back rpm to a previous version, I managed to complete the upgrade to 11.3 and everything looked good. However, when I rebooted the system, it hangs at a blank screen. More precisely, the system seems to get through all of the BIOS stuff and then hang while loading the OS (I assume). Although I've worked on Windows boxes for a long time, I'm a complete novice at OS installations/upgrades for Linux systems, so I'm not even quite sure where to begin to troubleshoot this. Ideally, I'd like to be able to fix the installation on the system to save the data on the hard drives, but I realize this might not be possible. My first thought was to use a recovery tool that I'd seen on some Linux installation CDs, but I see that for openSuSe 11.3 and on that utility has been dropped. I can, however, use the disk to get to the "Rescue" command prompt, so maybe there's something I can do from there?
Basically i install Ubuntu using a boot CD and it install 100% but after i restart my desktop the screen just goes blank, i can run it of a live CD.The same thing happens with openSUSE and zorin.
View 7 Replies View RelatedI'm extremely close to getting ubuntu on my old Toshiba Sattelite 1135-S155. It meets the minimum requirements (barely).I was able to go through almost the entire install process, but at the end when I restarted, I was told to remove the disc and hit enter, which I did. Then nothing but a black screen with a blinking cursor and unresponsive keyboard. I powered down, restarted, and got the grub. Same thing: it identifies the Ubuntu OS , but when I select it to boot, nothing but a black screen with a blinking cursor and unresponsive keyboard.
I'm trying to run this machine purely on ubuntu- no windows installed.I can actually load and run the OS from the "Try Ubuntu" option that rune off the CD.
I installed a new graphic card from ATI 5770 (Club3D). After I did it I removed the propriatery ATI drivers I had installed thru the "Hardware Drivers" in Ubuntu and rebooted. Then I couldn't get into ubuntu again. When it starts booting the display just shuts down and says "Power Saving mode". The computer continues to load things etc. left it running and hoped it would show itself... nothing.
Anyway this happens everytime even with Live CD so I can't even get to a terminal... Started the boot without the splash and it went blank after it started some Speech thing. Just before that there were a few firmware files missing.
I just reseantly got an Asus Essentio CM1730-05 desktop and I installed Ubuntu 11.04 on it with Wubi. After doing so, I installed the restricted driver for my onboard ATI Radeon 3000 graphics. After doing so I get to a blank screen right after the splash screen. Also I think it is frozen because I don't here the Log in music and I have to hard reboot instead of just hitting the power button. If you need to know more about my hardware just ask. Also I have tried two different monitors.
A Dell M991 and my HDTV. I have used the following hook ups to the HDTV-DVI to HDMI and HDMI to HDMI. The Dell M991 is like any older monitor. Just that one VGA hook up. I noticed there is an Asus section so I hope that this is still the right spot. I have tried the following. Replace quiet splash with nomodeset and also i915.modeset=1. I have yet to try i915.modeset=0.
i had a serious problemafter i checked my hardware detected by using liveCD, there's no problem i thoughti successfully installed it on my PCbuti got blank/no screen appeared when it started up
View 1 Replies View RelatedSo I Installed OpenSUSE A Plethora Of Times. In Both 32 & 64 bit. But No Matter What After It Boots Up And Where I Should See Some Kind Of User Interface The Screen Is Blank. Now this Is The Point Where You restart The Computer And See Where You Went Wrong But Come to find Out My Power And restart Buttons Dont Respond So i Have To Pull the Battery Out Of My Laptop.
View 4 Replies View RelatedAfter struggling to install openSUSE 11.2 on my computer with ATI radoen graphics, I finally managed. Rebooting just after initial installation caused my laptop to give me a blank screen, no command prompt, nothing. With some help from the only post with such a problem on Ubuntu website and after first installation, I did the following:
1. Boot from Live cd of opensuse 11.2
2. Mount the partition which has root.
3. check for and delete Xorg
[code]...
i installed, few days before susu 11.2 . now my lcd only has resolution of 800x600, so i type "sax2". after he made that config, suse displayed me a gui, where i can change resolution and my frequency. i selectet native resolution and freq. (the right nvidia driver and lcd was detectet) and hit that apply button, then i needs to restart. done it, but then i got after that loading bar of suse only blank screen. so what was wrong ? and what i can do now to fix ?
View 2 Replies View RelatedI have the problem (11.3) that the screen is blanked after 10 minutes (console and KDE). After some searching, I found out, it is a kernel "feature". Since it is a server, which should display network status permanently on screen this behavior is fatal.
I have tried:
- switch of power features vie Grub kernel param: apm=off, powersaved=off
- in kde via screensaver options
- in term "setterm -blank 0"
A surprising thing has happened! I have been happily using open suse 11.3 on an HP probook 4320s laptop. On reboot this morning, the screen starts out fine, but progressively fades into white and the boot does not seem to happen (at least there is no sound, since I cannot see anything). I am left with a completely white screen. Things are fine with the failsafe mode.
View 9 Replies View RelatedI just tried to upgrade from 11.3 to 11.4 Using iso on DVD. All went well until the stage where the screen says something like "rebooting from installed system" when the screen just went blank. After removal of the DVD and re-start of the system, selecting the normal Desktop from the boot menu just returns me to the blank screen. I never see a login screen.
Selecting Failsafe caused what appeared to be a complete normal sequence with a Login that worked and I ended up in KDE4 (my usual desktop) with everything apparently working, even WIFI. But the next time I re-booted and selected Failsafe I just got a command prompt. I now find that selecting Failsafe alternates between the GUI and a command prompt on each attempt!
[Code]...
After I install SUSE I reboot and click on Desktop it then goes to a loading screen. After that it scrolls a lot of info then the screen goes blank. I have no idea why and I have tried it on 3 different computers with the same problem.
View 3 Replies View RelatedI had ubuntu running just fine on another computer, but had to move things around to make Windows7 run better. So after backing up Home, I switched hard drives, pulled the video card, and adjusted RAM, I tried booting up. The computer found all the changes and did its thing. But then it hung with a blank screen. I figured that it didn't recongnize the video driver for this computer, or something, so I did a fresh install with 9.10 to start over from scratch. The boot up went great, and finished completely. I made a few changes to the desktop, and loaded in my archived firefox bookmarks and evolution files. After rebooting, the first ubuntu logo came up, but then the blank screen, with no drum sounds. I tried a few more times rebooting and hitting esc, but I don't know what I am doing at that menu. I also tried the F1 option, but again, I don't know anything. One other time I was able to boot into ubuntu all the way when I was hitting esc slowing (waiting) and somehow was able to get the login and the desktop just fine. I haven't been able to get that to happen again.
Can someone walk me through the steps to troubleshoot this? I don't know any terminal jargon or commands, and haven't really got a clue, but I really want to learn and figure this out. I don't even know how to go in from the command line to see what my system specs or video specs are to tell you.
My laptop: MSI AMD Athlon 64x2 Nvidia GeForce GO 6100.
I've done a fresh install of Ubuntu 10.04 and I end-up with a blank screen. I've also tried a fresh install of Xubuntu 10.04 and Kubuntu 10.04 and I get the same blank screen.
Ubuntu 9.10 was working perfectly though. So what do you think happened?
I installed the Ubuntu 10.04 livecd on my desktop and it works perfectly so I think it is not a burning problem.
I have installed today Ubuntu 10.4 LTS ..after installation the OS does not boot and just shows blank screen with cursor blinking ...any idea ..I have searched the forum a lot but cannot understand why this is happening ..re-installed twice ..This is AMD64 bit but I am installing the 32 bit ubuntu 10.4 LTS.
View 9 Replies View Relatedtrying ti install ubuntu server 10.04 64bit server edition.Ok so I have been using the desktop version as an internal server at my home office.Decided to give the server edition a try. Now when I start the installation I get the language choice, then I choose install and then my screen goes blank and nothing happens.
View 3 Replies View RelatedI just setup a Fujitsu s6231 lifebook with Lucid. When I boot there is no grub menu unless i press the "start" key. Then the only way i can get into the machine is by entering into recovery mode and booting in "safe graphics mode".
Everything works fine once I am able to log on the "safe graphic mode".
If i don't press the "start" key the ubuntu logo will flash for 3 seconds and then the screen goes blank and nothing happens.
I just bought a new Dell Latitude E6510. When I boot from the Ubuntu 10.10 64bit disk (I've checked the disk for errors already), the initial, purple splash screen comes up, but then the screen just goes blank and stays that way. I never even see a grub screen.I tried Linux Mint 9 with both the 64 bit DVD and the 32 bit CD. Both Mint disks bring up a grub boot screen, but then the screen goes blank just like Ubuntu 10.10. I can hear Mint's "login" sound, but nothing shows up on the screen
View 3 Replies View RelatedI'm trying to install 10.04 Server on an old Dell Poweredge 600SC I had lying around, and I'm having an issue with the installation. I can boot from the disk without any issues, I select a language for the installer, and I get to the main menu (Install Ubuntu Server, Check Disk for defects, Test Memory, etc). When I select Install Ubuntu Server, it waits a couple of seconds and then goes straight to a blank screen. No flashing cursor or anything.
I've tried some digging on the issue and another thread from a while back said to add "vga=771" to the installer line and when I did that, I got an error from my monitor itself complaining about an incompatible video mode.I know I'm not the only one who has had this issue, I just don't know how to address it. This is the first problem I've ever had on an installation.
So I currently have an install of Karmic running that has been upgraded over the years but I am repartitioning my drives so I did a fresh install on a new drive.
My first problem was the live cd would not boot and I had to use the alternate cd to do the install. It would boot into a blank screen and the i915.modeset=0 kernel parameter did not help.
After the installation finished I went to try and boot and found that right when it went to initialize the graphics, my computer locked up hard. Keyboard unresponsive and all. I read the forums and I tried using the kernel parameter i915.modeset=0 and removed quiet and splash from the kernel line to see if I could spot any errors but nothing appeared.
I am able to boot into recovery mode, and I tried even running an apt-get upgrade to get all my packages up to date and installed the latest nvidia driver but still have this issue.
I'm at a loss as to what I should attempt next.
Here is boot info, just to clarify sda and sdb are a fakeraid on my old setup, sdc is my new install
Boot Info Summary: