I've lost 6 CD-R's to this error. I have no idea what the hell could be wrong. I do not have a SCSI interface in this unit, but no matter, when ever I try to burn a cd it starts and then spits out this error; "SCSI error on write(16,16): [5 21 02] Invalid address" The log from the first attempt to burn that fails. Just before this I had burned a CD and the only problem was it couldn't eject it at the end.
[Code]...
i m facing same error in most of the HCL servers. the problem is that it throws error while booting and sometimes not throws error. the error is :-
Feb 13 13:17:25 fe13s kernel: Adapter 0: Bus A: The SCSI controller was reset due to SCSI BUS noise or an invalid signal. Check cables, termination, termpower, LVDS operation, etc.
Feb 13 13:17:30 fe13s kernel: Adapter 0: Bus B: The SCSI controller successfully recovered from a SCSI BUS issue. The issue may still be present on the BUS. Check cables, termination, termpower, LVDS operation, etc
Feb 13 13:29:15 fe13s kernel: Adapter 0: Bus B: The SCSI controller successfully recovered from a SCSI BUS issue. The issue may still be present on the BUS. Check cables, termination, termpower, LVDS operation, etc
code....
This morning it would not boot; when I tried to wake up the system, it gave me a bunch of errors, the last ones being as follows: "mount error: could not resolve address for servername: No address associated with hostname mountall: mount /media/shares [1402] terminated with status 1" I am writing this in Win 7 since I lost ubuntu. I am using ubuntu 11.04.
View 2 Replies View Relatedxbmc 9.11 HTPC (confluence skin) on an acer revo 3610 running ubuntu 9.10 can someone possibly help me as I cannot get WOL to work. Went into BIOS under power management and enabled WOL.I have used this guide to set up. HOWTO: Set your system up for Wake On LAN (WOL my ipconfig is
Quote:
xbmc@xbmc-desktop:~$ ifconfig
eth0 Link encap:Ethernet HWaddr 90:fb:a6:2c:b2:1f
inet addr:192.168.1.11 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::92fb:a6ff:fe2c:b21f/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[Code]...
I then tried to follow this guide HOW-TO set up Wake-On-Lan (Ubuntu) and followed those steps also still nothing. I deleted this script however as it did nothing and didnt want to have two scripts that might be interfering with each other.How can I check that the magic packs are being received by the computer? I think it has something to do with the MAC address but Im a linux noob and gettng kinda lost now, ANY help would be much appreciated. I also have a another linux computer hooked up on the network to test however I want to WOL via the internet incase I am traveling and need to wake up my htpc. Can anyone please help me as I think I have the scrips installed and Im just not doing something simple like configuring the magic packs correctly to send the information.
I've just installed a fresh copy of Maverick Meerkat 64bit and I wanted to setup static ip, but unfortunately I can't because of invalid mac address detection during each startup. The message looks like this
Code:
dmesg |grep Mac
[ 5.988576] forcedeth 0000:00:07.0: Invalid Mac address detected: 0b:68:66:ea:0f:00
[ 5.988590] forcedeth 0000:00:07.0: Please complain to your hardware vendor. Switching to a random MAC I remember having the same problem on suse distro and the solution I found at that time, was to change the /etc/udev/rules.d/70-persistent-net.rules and edit it to look like this
[Code]...
When I am using Mailutils to send messages to myself as a test, I get them but they are from <"ryandward@ryandward"@gmail.com> which is not a valid email address and I have no idea why my system is configured to send them from this address. This is indicative of some problem there is going on in my system.
View 9 Replies View RelatedIn my understanding, the way /proc/scsi/scsi gets populated, /proc/paritions also gets populated in the same fashion. i.e. the description for first entry of /proc/scsi/scsi can be seen in the first entry of /proc/partitions and same for rest.
So, With this assumption, in my project, I used to relate first entry of /proc/scsi/scsi with first entry of /proc/partitions to get its total size and same for all entries.
But, I observed some differences in following scenario, where
1) The first 4 entries in /proc/scsi/scsi are SAN luns attached to my system and for which the actual device names in /dev/ are sda,sdb,sdc and sdd.
2) The last 4 entries are the internal HDDs on same system. In /dev/, their respective device names are sde,sdf,sdg & sdh.
(Output attached at end of the thread)
But in /proc/partitions, the device order is different.
You can see their respective sizes in /proc/partition output as well.
So, my question is, in this particular scenario, I can't relate the first entry of /proc/scsi/scsi with first entry of /proc/partition. i.e. scsi0:00:00:00 is not /dev/sde, because it is actually /dev/sda.
It seems that my assumption is wrong in this scenario.
Is there any way or mechanism to figure out actual device name for an entry in /proc/scsi/scsi in /dev/ directory?
How can my application should relate /proc/scsi/scsi entries with their respective device names and sizes?
When I enter "cat /proc/scsi/scsi" I'm returned with "cat: /proc/scsi/scsi: No such file or directory". I've tried this on two different installs on two different machines.
View 6 Replies View RelatedSome of our workstations have LTO's attached and they seem to drop off every now and again, the only thing which picks them up again (besides a reboot) is the famous rescan-scsi-bus script from here
The thing is that I'd like non-root users to be able to run this script, which in turn needs root to /proc/scsi/scsi
I got the Raspberry pi 2 Model B. I flashed my sdcard with raspberian Jessie kernel 4.1 (latest).Also tried wheezy and NOOBS, same behavior.With a ethernet cable (known working), I tried connecting my Pi to my home router, and I got a invalid ip address 169.254.xxx.xxx, and therefore no linkup. I got the same results by connecting my Pi directly to my modem (wired).
I know that /etc/dhcpd.conf is the new /etc/network/interfaces for network configurations.So I tried the debug option, and I noticed that the router doesn't seems to response to the DISCOVER command from the Pi (dhcp v4 protocol).Here's a dump of by /var/log/syslog | grep dhcp
Code: Select allDec 28 12:00:02 raspberrypi systemd[1]: Starting dhcpcd on all interfaces...
Dec 28 12:00:02 raspberrypi dhcpcd[349]: version 6.7.1 starting
Dec 28 12:00:02 raspberrypi dhcpcd[349]: udev: starting
Dec 28 12:00:02 raspberrypi dhcpcd[349]: dev: loaded udev
Dec 28 12:00:02 raspberrypi dhcpcd[349]: eth0: disabling kernel IPv6 RA support
[code]...
ANd if i use raspbian flesh out of installation, I get this when i run
dhcpcd -k
dhcpcd eth0
eth0: probing for an IPv4ALL address
eth0: using IPv4ALL address 169.154.202.224
Seems like my home router TP-link (default setup) doesn't send a response to the dhcp request.
Kubuntu's Network manager says that my (wired) network is in an invalid state because I don't have an IP address, but Firefox and Chorme work perfectly, as do Synaptic and Software Centre, and a Superkaramba network monitor says that my IP is "192.168.1.101" In fact, the only thing that isn't working is Pidgin, and it says it's "Waiting for network connection."
View 3 Replies View RelatedBottom Line: Dvd Drive died in my toshiba laptop and it was replaced (not before tech for some reason reformatted the Win7 partition... which was 100% un-needed, but thats beside the point now. I redid win7 (the tech installed vista) and am TRYING to "redo grub". Facts: The Slackware AND Ubuntu Partitions ARE STILL THERE and when i use SuperGrub Boot CD (which doesn't restore my grub by itself) to boot into slackware, i can see ALL THE CONTENT of both Linuxes still there including grub on ubuntu partition
(Tri-Boot: Ubuntu, Slackware, and WIn7) I had it working for two years or so, SO i know this "setup" works fine. I am A) Trying to do this as simply as possible. B) Trying to avoid the need to download a 800MB ISO (as seen for this issue on this forum) and trying not to have to reformat Ubuntu Partition (though I have the .Debs I have downloaded for it backed up ... all 1.7GB of them) I have /dev/sda1 as win7, /dev/sda2 as Slack and /dev/sda3 as Ubuntu (which contains Grub Legacy).. Every command I do seems to result in an error like "invalid command" or "invalid Execution format " (i think that second one is right) type errors. I compiled (awhile back) a few kernels for Slackware, but feel goofy that I cant figure what i this out (what i thought was going to be a "2 minute" fix)
I currently have a massive problem with my main webserver: one of the SCSI drives where I keep my htdocs seems to have failed (sd 0:0:0:0: [sda] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK,SUGGEST_OK end_request: I/O error, dev sda, sector 7797601).
Since I have no backup (dumb!dumb!dumb!) of it, I tried to copy what I could on the fly, but that failed miserably. The next idea was to umount the volume and try remounting it R-O, but I have a bunch of apache2 processes that are apparently reading/writing on it and I can't seem to find any way of terminating them. I tried via init script, killall and kill -9 but they just don't respond. Until I can terminate those processes, I won't be able to unmount the drive and try saving what's left of the data.Oh and the cherry on top of the cake: the server is 1100 miles away so I can't even access it physically..Is there any way I didn't think of to get rid of those apache processes?
I am working on implementing a protocol on NS2.34 .I really need help to solve this problem . Actually , I don't now whether the problem is generated by the tcl code or the c++ code when I run the simulation, I get this result :
Code:
num_nodes is set 64
INITIALIZE THE LIST xListHead
34
45
channel.cc:sendUp - Calc highestAntennaZ_ and distCST_
highestAntennaZ_ = 1.5, distCST_ = 550.0
SORTING LISTS ...DONE!
code....
One of the tasks I want to do is to read/write from/to any physical address. My question is how do I get a physical address on my Linux desktop. I was thinking of using some utility to dump my BIOS settings, and modify a "not so important" memory address there? Is this possible. Otherwise is there any other physical address I can read/write
View 3 Replies View Relatedi have a linux machine installed with RedHat 4.7 x64 bit. toady our machine just hanged and the only thing we can do was to do an hard reboot.i saw that when she hanges all her disk looks offline. in /var/log/messages i only saw this error message:
kernel: lpfc 0000:10:00.0: 0:0713 SCSI layer issued LUN reset (0, 4) Data: x0 x0 x0
we have 6 disks in RAID 5 in this machine- SAS disks. i've search in the net and looks like the emulex driver told the SCSI to do a reset for some reason. how can i check this issue? machine is online now and everything looks ok but i'm afraid i have a problem perhaps with my disks and this is a production machine so it cant happened again.
I installed the citadel suite on ubuntu server 9.10 Email obviously works fine internally. I tried to setup a smart host to send my mail through as my isp(Verizon) obviously blocks port 25. I tried to send out the Verizon smtp server on port 587. In the Administration> Domain names and Internet mail configuration>Smarthosts.My smarthost entry on the citadel configureation page above was usernameassword@outgoing.verizon.net:587 but after sending an outgoing email, it comes back with a "invalid/host-not-in-DNS return address not allowed"
I have also tried using gmail and a hotmail account with the respective smtp address's in but they come back with "Must issue a STARTTLS command first".I have researched both messages and come up with squat that has helped me.
I know that my mail will have to go out through a smarthost of somekind. So is am I on the right track with choosing verizon/gmail/or something else as my smtp relay, or is there a free service out there that I can send email through(haven't found one if there is)
Anyone else ever setup Citadel and got around their isp blocking port 25?I am also not sold on citadel, it was just the first/ nicest looking one that I found.
I installed the Centos 5.5 and after the Xen. After I put a virtual machine named VM01.Initially it worked properly, I tried everything and it worked.When rebooted, I had problems with the network.I have two network cards eth0 and eth1, but eth1 does not have any ip and I use only eth0.The error that appears is:
vif0.0: received packet with own address the source address
i finally decided to updgrade from Hardy Heron to Lucid Lynx. for this i made a backup of my old install, then i couldnt find my Lucid CD so i used a Karmic one to partition my old ext3 to ext4. There were some errors but after trying a few times it worked. Installed Karmic, rebooted (worked fine), downloaded all updates - (did NOT reboot to let updates take effect) and upgraded to Lucid.
Everything went fine so far. Now when i try to boot into Lucid the system hangs, i've also got a windowsXP partition on there so i tried booting that, first grub tells me Error 29: Disk write error then trying again windows seems to boot but it takes much longer than it should and seems to hang.
Then i tried Karmic and Lucid LiveCD (which i found in the meantime) none of the LiveCDs make it to boot after about 20 minutes. (previously they worked fine)looking at the errors it seems to be something about the harddrive. Why the harddrive would stop the LiveCD booting is a mystery to me but the same messages appear when i select Recovery from the Grub menu so i guess the problem is related.
[Code]...
df -h [URL] I did the following command to find everything is in /usr or /var, then tracked it down to /usr/lib and /usr/share as the main offenders, but out of all the directories none are more than 1mb or so.
du -sh /* | sort -gr | head -n 5
I tried to uninstall firefox, which is what got me in this mess in the first place, the log claims it will remove ~240 mb but failes on a "E: Write error - write (28 No space left on device)" [URL] If I could juggle something onto an external hard drive so I can uninstall firefox I would be out of the wood. Failing that I believe a new install is in order.
i downloaded baldurs gate II shadows of amn iso's, because i lost one of the CD's to the box, but anyways, I went to mount the third .ISO for installation, and BAM! my computer froze, so i waited five minutes, came back, and still frozen. shut it down for 20 minutes, pulled it back up, and it's got this error as follows; "Mount: mounting /dev/disk/by-uuid/65b0a6a-a366-435a-a086-58428cfe2bd1 on /root Failed: invalid argument
[code]...
I have message: error 12: invalid device requested.It happen when i choose ubuntu partition. before this error message the netbook run perfectly with dual boot. ubuntu is 1st option winXP is 2nd option from the list(maybe grub ?) Since i want winxp as the 1st option instead ubuntu,i change the file /boot/grub/menu.lst. what exactly i change is just cut and copy the winxp part to above ubuntu part.
if i press 'e' in ubuntu show:
root (hd0,6)
kernel /boot/bla..bla.bla..
initrd /boot/bla..bla.bla..
[code]...
Since May 12,2009. Our system lifekeeper has the error log "lifekeeper error: DEVICE FAILURE on SCSI device '/dev/add'", but it ran normally. Until last week, it failover to the standby server. The disk still running, the error still come out.
View 3 Replies View RelatedI open an ODS file and edit it and save, fine. But sometimes and for no readily apparent reason it refuses to save the document with the error message:"Error saving the document <filename>: Write error. The file could not be written". I have upgraded my version of OpenOffice but the issue remains. Once it starts with that error the only way to save the file is to actually abandon my change and restart OOffice. Today I lost an hours stuff as the auto save was also failing but not giving me any warning it was failing. I'm not sure if this is an OpenOffice, file system, Fedora or permissions issue though I've not noticed anything similar with other applications. Have set permissions to 777 but still get the error.
View 3 Replies View RelatedI've searched all over the internet and have found numerous threads on this topic, none of which have helped me fix the problem. I'll post as much info I can about my setup.I have 3 hard drives... one is for ubuntu (9.10), one is for my data, and one is for Windows7. It looks like this:
1st drive (hda) = ubuntu
2nd drive (hdb) = data
3rd drive (hdc) = windows
[code]....
i'm runung "ubuntu 10.4" and install "Xampp 1.7.3.a" i have 3 problem in the joomla web installer in step "2:Pre-installation Check"
Code: configuration.php Writable NO
in step 5 : FTP Configuration when i feel ftp setting and click on "verify ftp setting,get this error Code: Error: the XML response that was returned from the server is invalid.
inthe final step when i click "install sample data" i get this error
Code:
Error: the XML response that was returned from the server is invalid.
I am running Red Hat with 2.6.18-194.8.1.el5PAE kernel version. I am trying to run encryptfs to encrypt a partition on my hard drive. One of the kernel modules necessary is the md5.ko. I noticed it wasn't loaded in when doing an lsmod. I tried running modprobe md5 and it fails to load:
[root@ ~]# /sbin/modprobe -v md5
insmod /lib/modules/2.6.18-194.8.1.el5PAE/kernel/crypto/md5.ko
FATAL: Error inserting md5 (/lib/modules/2.6.18-194.8.1.el5PAE/kernel/crypto/md5.ko): Invalid argument
I ran dmesg and grepped for md5, but I didn't see anything in there.
I'm running ubuntu 9.04 and trying to pull over some files via the GUI from a XP box over locally. I'm getting this error:"error while copying file into /volcano/tunes invalid argument" (under show more details)If I just copy over a mp3 file it works fine but the when I copy the entire directory I get this error.
View 9 Replies View RelatedI've been googling all afternoon to fix this error I get. The situation is as follows: I have multiple harddrives (3x320gb and 1x160gb) all on the SATA interface. One of these drives contains Windows, and the rest I use for programs and downloads. I've installed Ubuntu 9.04 from a USB-stick using the installer's partitioner to make some room for Ubuntu (Ext4 filesystem). I've tried Ubuntu and SUSE in the past.
View 1 Replies View RelatedI am a long time Windows user and attempting to install Ubuntu Netbook 10 on my Acer Aspire netbook.I followed the steps:1) Downloading the Ubuntu ISO to my netbook hard drive.2) Installed Ubuntu from the netbook HD to USB using USB universal installer (also using the universal installer to format the USB)3) Set bios to first read USB deviceI receive the following message during the boot "Invalid system disk. Replace the disk, and then press any key.I have retried this process several times.
View 2 Replies View Related
