I just recently installed Ubuntu and my power supply cooling fan won't power down normally when I would run windows tho it would power down after the system was finished starting up. How can I remedy this?
View 1 RepliesIs there a way to do that since the computer and OS is aware that the power supply is disconnected.
View 6 Replies View RelatedMy pc had hardware malfunction; power supply interruption. At this moment it is working stable. My Windows 7 installation is ok but Ubuntu Maverick which I used during crush has malfunction. When I start to boot it looks like this: I had to make a foto so you all can see the problem. all my important files are stored on Ubuntu partition..
View 4 Replies View RelatedDoes anyone had any experience with fanless, low-powered power supply units (PSUs)like PicoPSU? Please share your experience.
I am also interested to hear about experience concerning the fanless cooling solutions and/or power-scaling for low-end CPUs like Intel's Atom, AMD's Neo or Via's Nano.
Is it technically possible to use just one power supply for more than one motherboard?The reason for asking is that I have a number of old (a few years) boards that I would like to use to make up a blender render farm yet only have one spare PSU. Having looked at the pin spec URL...pin 16 (power on) should only be connected to one board (or have a manual switch to ground for on)Pin 9 (standby +5v) probably should only connect to the one board or none and the other (or all) boards would need pin 9 to be tied to a +5v pin.All the boards would network boot and have nothing connected to them, no disks, floppies, monitors, etc; as all data would reside on a network server.
View 3 Replies View Relatedis this a good combination to use with 8 GB of RAM and 2.6 GHz AMD Hex core? The power supply will be replacing a 450 watt power supply and the video card will be replacing an ATI 5750 1 GB (Which currently doesn't work without 10.9, so far) The problem with these is that it doesn't meet the AMP rating of 38A of the GTX 470.
View 1 Replies View RelatedI have a 500GB WesternDigital Elements external harddrive and recently I plugged it into my computer and noticed the green light on the power adapter didn't light up anymore. I'm assuming that the power adapter failed - is this a fairly safe assumption? I know it COULD be something else, but does this at least make sense to move forward?Coincidentally, I've been researching new externals to order a 1.5TB because the 500GB is full.
I'm contemplating two options:
1.) Replace the power supply for ~$40
2.) Take apart the external and mount it internally
If it is in fact the power supply it might be the best option to just replace the thing and have 2 externals for backing up data on. But if it turns out to not be the power supply I'm out $40.I'm not sure how taking apart the external and install the hard drive in a desktop computer would be. Is the harddrive a standard drive? Does it have all the same power cords a normal computer would? If so, I could just install it into my brother's desktop and retreive the data that way (and he'll have an extra 500GB hdd).
I have installed on my computer Solaris10 (64bit version), PCBSD8 (64bit) on 2 primary partitions and 7 Linux distributions (Redhat,Debian,OpenSuse,Fedora,LinuxMint,Slackware,Ubuntu) on the extended partition. I know this might be a stupid question, but here it goes: I have a problem with my actual power supply unit (the fan doesn't work as it should) and I will change it soon. Is there a problem with any of the Linux distributions if I change my power supply unit? I mean, will the Linux operating systems work properly with a new power supply unit or do I have to reinstall all Linux distributions?
View 4 Replies View RelatedSo now that it's working the Server can't be seen from the internet. I see that the router changed all the ip address so I changed the fort port forwarding on the router and still not working. And the external ip address has not changed.
View 4 Replies View RelatedMy router/adsl modem is not connected to a power supply so when power goes and comes the network will do a re-boot. Now the problem is my OpenSUSE network won't come back on! I set the static ip as Autoeth0 to eth0 however when network updates I losse eth0. Why is this happening? Why doesn't the PC simply re-connect? Can I do it via command line?
View 5 Replies View Relatedcome across with this issue for one server we are giving support please,help me to know why this issues occurs and alsothat i want a command to display power supplies for the server.please,let me know if anybody is familiar with these kind of issues.
View 2 Replies View RelatedI'm a heavy user of Eclipse. It's my workhorse. Today, the thing started crashing on me. So, I started the thing from the console to see what the last message is before crashing, but...nothing. It crashes whenever I hover over something that is supposed to give a pop-up (you know, the yellow-ish popup with a help text).
Any clues to what I can do to remedy this? As I noted, there are no return messages, so, that's all I have here...
As soon as my ubuntu OS is booted, the cpu fan on my computer stops working, and wont start up again, I am using an acer aspire 5315, and and the most up to date version of ubuntu.
View 3 Replies View RelatedThe cooling fan on my Toshiba Satellite m500 doesn't work after installation of ubuntu 9.10. I've looked on the internet but i can't seem to find anything.
View 4 Replies View RelatedI have a Dell Vostro 1520 laptop and dual boot Windows 7 and Debian 7.8 64-bit. Windows 7 does use a lot of resources and the cooling fan kicks in almost all the time and it's a bit noisy. So I installed Debian which makes a big difference as it uses less resources so the fan is on less often.I just installed LXDE desktop to try to reduce this even further and I must say it is much better but fan still comes on even when laptop is quite cool so not sure why fan is kicking in so early.
Any best software to control when the fan comes on. If there are any good tools that are easy to install for someone who is quite new to linux? URL...
I installed Fedora on my notebook ASUS. When I type on terminal dmesg apper this:
ACPI: Unable to turn cooling device [db816540] 'on'
I try to search a solution for this but I don't find it.
I get the Subject message posted every few seconds in /var/log/messages. I had the same issue with kernel-2.6.18-92.el5.
# uname -a
Linux mine 2.6.18-128.1.1.el5 #1 SMP Thu Feb 12 01:53:39 GMT 2009 i686 athlon i386 GNU/Linux
# rpm -qa kernel* | sort
kernel-2.6.18-128.1.1.el5
[Code]....
I have two situations here :
1) I have my Nagios running on the linux box and BMC Remedy Server on the Solaris box. I have simulated a mail from Nagios to be delivered to the Remedy server. But the Remedy Server does not receive it. I even tried snooping on port 25 but nothing has reached the box.
2) I have my Nagios running on the linux box and BMC Remedy Server on the Solaris box. I have simulated a mail from Nagios to be delivered to the Remedy server. I snooped on port 25 on the Solaris box. I could see the mail reaching the box, but it is not being forwarded to the Remedy inbox.
know whether it is possible to disable +5V supply on USB and enable it again?
View 4 Replies View RelatedI will be staying at a hotel for a couple weeks that has a wired internet connection to each room. I have a Linksys WRT54G v6 wireless router and would take with me and set it up so I would have wireless in my room.
View 2 Replies View RelatedThe upstream provider is supplying samba3x (currently samba 3.3.8) packages in their supplementary repository. I know that most of what is in the supplementary repository is burdened with restrictive or non-free licenses, however, Samba is not.
The samba3x packages are critical for Windows Server 2008 trust relationships as well as Windows 7 client support for a CentOS server acting as a Windows domain controller. I know that I can either roll my own packages or compile from source, but an officially supported version would be a much better option on a production server.Is there any way CentOS can "officially" supply these packages and their associated dependencies?
I am trying to write an irc bot to run interactive fiction games in a channel. I am connecting to the channel using nc. I'm having a hell of a time trying to supply input stdin for nc after the connection is established. Here's what's going on. I've got lines of plain text in a file with the irc commands required to identify the bot's ID and join the channel. I can connect easily using any of the following commands
cat inputfile | nc irc.servername.org 6667 -i 1
nc irc.servername.org 6667 -i 1 < inputfile
Named_Pipe | nc irc.servername.org 6667 -i 1
cat inputfile > Named_Pipe
With the first two commands nc connects, reads the file with some time between each line allowing the irc server to respond, bringing me into the channel. It then begins to receive stdin from the command line allowing me to do things like "privmsg #channelname :Hello World!!!" sending messages to the room. This is not the desired behavior. I require nc to take additional stdin from the inputfile if I cat additional text to the end of it.
The last set of commands using the named pipe seem like it does the same, but it doesn't actually send anything to the room, which indicates to me that perhaps nc is continuing to take stdin from the named pipe (this is the desired behavior) rather than dropping to the console for stdin. If I try to cat more plain text data to the end of the named pipe, however, either with something like "echo 'privmsg #channelname :Hello World!!!' > Named_Pipe" (or >> instead of >) or with a filename in place of the "echo" command the whole command simply seems to hang until I press ctrl-C.
I don't understand what I'm doing wrong. With anonymous and named pipes, and with redirection, the problem seems to be the same. nc seems to take it's stdin from the file until it hits the end of file, at which point I can no longer introduce new lines of plain text as stdin for the running nc process.
I followed this tutorial to encrypt my entire installation: SDB:Encrypted root file system - openSUSE
It worked splendidly and whoever wrote it should get a lifetime supply of beer. After I got the install encrypted I made a RAID 1 array of 2 1GB disks and encrypted that as well. They are used for a data repository.
[Code]...
I have the following commande /sbin/fuser -f -u /u/DT01/F010107 1>/tmp/null 2>/tmp/seausr.T0069 when executing as root 'su' this give me all user using the file. but when tried with 'sudo' i am asked with 'user password'. Is ther anyway to simply get the result without having to supply a password and to see all user not only me. (i have the file open also).
View 1 Replies View RelatedThe kitchen kernal message is (33489)484879 ACPL Unable to turn cooling device{6c2a18}"on"
View 1 Replies View RelatedI am using Ubuntu 10.04 64-bit and I purchased a new ALFA AWUS036H wireless card. I would like to know if this "1Watt" wireless card is configured for full power. iwlist wlan0 txpower results:
wlan0 unknown transmit-power information. Current Tx-Power=27 dBm (501 mW). It appears to me that I should be able to increase the power. "iwpriv wlan0 highpower 1" does not work. Do I need to patch the new default driver that comes with Ubuntu 10.04 64-bit with the aircrack one following these directions:[URL]...? Monitor mode and a injection tests seem to work fine with the driver I have installed.
I use Squeeze with Xfce. My problem is that recently (after the xfce updates) the xfce power manager doesnt react to the power button - it is set to suspend. I dont have gnome-power manager or anything like it running.
If i reboot the computer, the power button will work but if i suspend and resume, it doesnt work again.
The computer is built on an Asus M3N78-VM mobo (2GB RAM/Athlon3200+ single core).
acpi_listen detects the button press.
Any thoughts?
I'm looking for any power monitoring devices for Linux to allow monitoring power quality, voltage changes, and outages. This would be for North American three phase power system. I want to have this data fed live to my own program. It should be something much better than just jury-rigging a circuit to fee the power waveform into 2 or 3 audio cards.
View 10 Replies View RelatedOn the last release, I had this app installed where I could pick my power profile. I could use power conservatively, and performance would suffer a bit, but longer batt life,or I could have it automatically detect, or I could have the apps use all the power they want and then some. I'm looking to reinstall that app. What was the name of it?I can't remember, and so far, can't find.
View 2 Replies View RelatedI had unplugged my PC last night as sometimes there's storms at night this morning I plugged in PC and the power light is blinking and the PC wont come on at all tried different power cord, same result
PC is a AMD athlon64 3300+ 2.4ghz SiS graphics
probably the power-supply or what?
If it is the power supply, how do I find new one as I've never had to replace anything on it or any other PC?
Also, I really need access to the hard drive but it's a weird hard drive and was wondering if I could put that hard drive in my K7 PC, which already has 2 drives in it can a pc have 3 drives? do I have to add/have another ribbon cable for 3rd drive?