Ubuntu Networking :: Wusb11v4 Sees Router Cannot Authenticate Wep
Jan 17, 2010
I'm getting rather bewildered.
I followed these instructions to setup my wusb11 driver using ndiswrapper:
[URL]
But when I try to ifup the interface, I get:
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 4
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 10
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 14
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
No DHCPOFFERS received.
iwconfig shows that no essid is assigned, even though I have specified one in /etc/interfaces.
Then if I go through the desktop gui Preferences -> Network to setup my wireless connection, /etc/interfaces does not seem to change but iwconfig then reports the essid is assigned.
Anyway, on my default taskbar there is a wireless icon. Clicking on that shows the wireless access points in the area. I see my own. When I try to connect to it, it prompts for my wep key. I enter the key, it thinks, and then acts as if I'd entered the wrong key.
Specifically of course, I'd like this to get fixed so that I can happily surf the net again, etc.
But I also I'm wondering why it seems that there is a disconnect between /etc/interfaces and Preferences->Network. If I type in a WEP key in the gui, I would think that it should appear in /etc/interfaces.
I'm definitely a Ubuntu wireless newbie, and not very experienced at Ubuntu anyway.
View 9 Replies
ADVERTISEMENT
Nov 27, 2010
Using a D-Link wireless router, trying to get it through the authentication process with the client through a D-Link DWA-125 USB wireless. When I set encryption to "none" on both ends, the router links up OK, but when I enter matching encryption settings on the router, and then in the driver data file (RT2870STA.dat) on the client side, I can't get it to authenticate. I've tried all possible combinations in the .dat file with no luck. I'm fairly well convinced that there is a bug in the .dat file settings, and that the wireless port setting need to be forced at startup through the /etc/networking/interfces file, or some such procedure, to override the settings in the .dat file.
[Code]..
View 8 Replies
View Related
May 12, 2010
Well this one is driving me nuts. I've been searching through the forums for a while and it seems that a number of folks have similar issues but the solutions used don't look like they apply to me. so without further ado here are the outputs typically requested:lspci
Code:
00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03)
[code]....
View 9 Replies
View Related
Jan 16, 2010
The problem: I am a poor man who until today was running WinXP on AMD64 using an old usb wireless wusb11v4 adapter (32 bit drivers). I have recently installed the Ubuntu 9.10 AMD64 release. But I cannot use ndiswrapper to load my 32 bit wusb11v4 driver because of the 64 bit os vs the 32 bit driver. I can hardly buy a new wireless adapter. But I do not see an AMD32 bit release.
View 3 Replies
View Related
Jun 28, 2010
Have linux 8.04 & acx111 wireless pci. Sytem sees the card but will not connect to network
View 2 Replies
View Related
Sep 22, 2010
I am using the Belkin wireless g usb adapter f5d7050 v1000 or at least that is what ubuntu says when I lsusb.
Code:
ceegee@Valar1:~$ lsusb
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 019: ID 050d:7050 Belkin Components F5D7050 ver 1000 WiFi
[code]....
View 2 Replies
View Related
Apr 13, 2010
Because of the configuration of my house, I need two routers.I have a DLink ADSL router as my main router and the Belkin N1 as my repeater.I have set up the IP address in the Belkin to be 10.1.1.10 - my DLink is 10.1.1.1. I have disable the dhcp in the Belkin and set the DNS as ISP provided. [URL]..I have set the channel to 11 and in the Ubuntu Network Manger I have set the IPV4 to Link Local Only. I can see the Belkin and connect with my PC.but it will not take me through to the internet.
View 9 Replies
View Related
May 13, 2010
I'm on ubuntu 10.4 and Cant seem to falsely authenticate myself with my AP. I am trying to break a wep key on one of my older linksys routers; It continues to say this:
Code:
root@kevin-laptop:/home/kevin# aireplay-ng -1 1 -a xx:xx:xx:xx:xx:xx mon1
No source MAC (-h) specified. Using the device MAC (xx:xx:xx:xx:xx:xx)
11:39:16 Waiting for beacon frame (BSSID: xx:xx:xx:xx:xx:xx) on channel 6
11:39:16 Sending Authentication Request (Open System) [ACK]
11:39:18 Sending Authentication Request (Open System) [ACK]
11:39:20 Sending Authentication Request (Open System) [ACK]
11:39:22 Sending Authentication Request (Open System) [ACK]
11:39:24 Sending Authentication Request (Open System) [ACK]
11:39:26 Sending Authentication Request (Open System) [ACK]
11:39:28 Sending Authentication Request (Open System) [ACK]
11:39:30 Sending Authentication Request (Open System) [ACK]
11:39:32 Sending Authentication Request (Open System) [ACK]
11:39:34 Sending Authentication Request (Open System) [ACK]
11:39:36 Sending Authentication Request (Open System) [ACK]
11:39:38 Sending Authentication Request (Open System) [ACK]
11:39:40 Sending Authentication Request (Open System) [ACK]
11:39:42 Sending Authentication Request (Open System) [ACK]
11:39:44 Sending Authentication Request (Open System) [ACK]
11:39:46 Sending Authentication Request (Open System) [ACK]
Attack was unsuccessful. Possible reasons:
* Perhaps MAC address filtering is enabled.
* Check that the BSSID (-a option) is correct.
* Try to change the number of packets (-o option).
* The driver/card doesn't support injection.
* This attack sometimes fails against some APs.
* The card is not on the same channel as the AP.
* You're too far from the AP. Get closer, or lower the transmit rate.
root@kevin-laptop:/home/kevin#
I'm using an eeepc 701 it has an Atheros card and does injection. I have also tried it with backrack 4 and it works perfectly (it falsely authenticates with the ap and decrypts the wep key) I just cant seem to get it to work on ubuntu 10.4. Could it be a kernel issue? I found out that there is a bug in the new(er) kernel(s). If you use an older kernel (I used 2.6.31-14 which can be found here) and it magically works.
View 8 Replies
View Related
Aug 22, 2010
I have a TP-Link Atheros-based USB card: TL-WN422G. It's listed widely as being compatible, but I'm baffled if I can make it work. I'm running an ndiswrapper (XP-64) driver, and that seems to be loaded and recognizing the hardware correctly. The system can scan and correctly identify our network, and other nearby ones, but when the WPA key is entered (correctly, I've triple checked), the "Secrets" windows just keeps popping up and no IP is acquired. I've installed and tried to configure it with wpa-supplicant, all to no avail.
I've attached below list of various outputs that I've looked at.
Ubuntu 10.04.1 LTS (Kubuntu); 2.6.32-24-server x86_64
output of lsusb
Bus 002 Device 002: ID 0040:073d
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 0413:6029 Leadtek Research, Inc.
Bus 001 Device 002: ID 0cf3:1006 Atheros Communications, Inc.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root .....
View 4 Replies
View Related
Jun 18, 2011
I want to set up a Linux box as a wireless router to replace our existing Netgear WNR1000 router, as I believe the Netgear does not support the coming IPv6 protocol. Unfortunately, it is not flashable with OpenWRT or DD-WRT presently.
As we have Comcast, our cable modem acts as a dumb modem according to the customer support guy I talked to, and our router is the one that asks for the IP address from DHCP. Thus, when Comcast switches over to IPv6, I don't believe my existing router would work, correct?
My idea is to take a Linux box and put two NICs and a wireless adapter in it, using IPCop or Smoothwall to set up a router. I could then enable IPv6 support for when we have IPv6 with Comcast. Is that possible? Would there be a way to get BIND to hand out private IP addresses in the same subnet on the both the LAN NIC and the wireless card?
View 1 Replies
View Related
Nov 6, 2009
I have a desktop PC running Ubuntu 9.10 and Windows 7, and a Eee PC 701 laptop running EasyPeasy Ubuntu 9.04. I'd like to connect the desktop to the laptop with a wired connection (eth0), then the laptop to my ADSL router using wireless (ath0).
I have a crossover ethernet cable (I bought on ebay). I have set up my laptop with a static IP address on my LAN and it uses OpenDNS.
I have added this to /etc/sysctl.conf on the laptop:
net.ipv4.ip_forward=1
Then I tried this on the laptop:
sudo iptables --table nat --append POSTROUTING --out-interface ath0 -j MASQUERADE
sudo iptables --append FORWARD --in-interface eth0 -j ACCEPT
This is a variation on what I found on other sites describing how to set up a router. I don't understand iptables very well, but I gather that the above two lines should set up forwarding so that traffic from my router to the laptop will be forwarded to the desktop, and vice versa.
But this doesn't work. The connection doesn't even establish between the laptop and the desktop.
View 12 Replies
View Related
Apr 24, 2010
I'm having trouble getting my network set up the way that I want it/had it. You see, when I first set up my network, I just had my cable modem going directly to my standard wired router (A D-Link DI-604), which had DHCP,and was connected to all of the computers on my network. I had one switch hooked up to one of the ports of the router, but this was a regular switch, and it would not try to assign IP addresses, it would just pass through the DHCP info as I wanted.
Now however, my network setup has changed. My room mate and I both got laptops, and we decided that we wanted to have wireless access so we didn't have to constantly plug in to the router.
Now my network is set up like this: The modem is hooked up to the router(DI-604), which is hooked up on the LAN side to our computers, our switch (which is hooked up to 3 more computers), and to a wireless router card (A Gigabyte GN-BC01).
The wireless router card has two jacks for ethernet. One for WAN, and one for LAN. The LAN side we have plugged only into the computer in which the card is installed.
Now the problem is this: The wireless router card comes with DHCP by default, and it's assigning addresses to the laptops and to the computer hat it's in, and worse, the IP addresses are on a different subnet than that of the main dlink router. The Main (dlink) router assigns addresses from 192.168.0.1 (itself) to 192.168.0.254, while the wireless router card assigns addresses from 192.168.1.1 to 192.168.1.254 (itself).
Because of this, I cannot access services on the wireless network from my wired network or vice versa. The first thing I tried was setting the card to assign addresses from 192.168.0.12 to 192.168.0.253, however it just said "internal error" when I tried to do this. I decided that this may be because it sees that it was being assigned an address on it's WAN side on the same subnet. So the next thing I tried was disabling DHCP and setting the "LAN IP Address" to 192.168.0.12, hoping that the DHCP would just go through the card, like a switch. I would have set the LAN IP address to be assigned by DHCP, but this was not an option, so I decided that'd be the best thing to set it to.
Once again however, setting the LAN ip address to an address on the same subnet as that of the IP assigned to it's WAN side caused it to report an "internal error". I verified that this was the issue by setting the LAN address to several other private IP addresses to test (I.E. 10.0.0.1, 192.168.3.1, 192.168.5.12).
My question then really is: How do I set up both routers so that I can access services and computers from each network from the other network. Should I set them with different subnets and set the gateway on the wireless network to the main router? To the wireless router card? Should I put them on the same subnet? Will it know how to communicate?
Here is a link to (picture) my network diagram. Network Diagram
View 2 Replies
View Related
Jun 6, 2010
however, until this morning I had only been using my wired connection with no problems but when I tried to connect to my home's WPA secured wireless network, it just would not connect. The network manager sees the network and when I click on it, a window pops up asking for authentication. I enter the passphrase, but still it will not connect. I'm using a Lenovo X61 LAPTOP (not tablet).
View 5 Replies
View Related
Aug 22, 2010
I have a TP-Link Atheros-based USB card: TL-WN422G. It's listed widely as being compatible, but I'm baffled if I can make it work.I'm running an ndiswrapper (XP-64) driver, and that seems to be loaded and recognizing the hardware correctly. The system can scan and correctly identify our network, and other nearby ones, but when the WPA key is entered (correctly, I've triple checked), the "Secrets" windows just keeps popping up and no IP is acquired. I've installed and tried toi configure it with wpa-supplicant, all to no avail.ched below a (long, sorry) list of various outputs that I've looked at
Ubuntu 10.04.1 LTS (Kubuntu); 2.6.32-24-server x86_64
output of lsusb
Bus 002 Device 002: ID 0040:073d
[code]....
View 2 Replies
View Related
Mar 26, 2009
These r IP provided by my ISP that i've put on Fedora 8:
WAN IP:xxx.xxx.xxx.17 (eth0)
Subnet:255.255.255.252
Gateway:xxx.xxx.xxx.18
Valid static(public) IP set of 2:
IP:xxx.xxx.xxx.147 & 148 (eth1, eth2)
Subnet:255.255.255.240
i want to run xxx.xxx.xxx.147 as a web server & xxx.xxx.xxx.148 as a ftp server. but I'm able to ping only xxx.xxx.xxx.17(WAN IP) from outside world. Can any1 tell me that how can i bring my 147 & 148 IP online without router.
View 6 Replies
View Related
Jan 2, 2010
True or False: If you have a user on your Linux/Samba machine with a password, example:
User = Bob
Password = Password0
And Bob is on an XP computer, where his username is also Bob and his password is also Password0, is it normal for Bob to go to:
\SambaServer, double click on Bob's share (valid users = Bob only) and Bob get RIGHT in without being prompted?
On my prior setup, the user HAD to log in. If they wanted auto login next time with their credentials, they had to check "remember password." But now it's as if Samba knows who they are. It's very strange. What's the normal behavior? Must EVERYBODY authenticate with passwords, or if the Windows credentials are the same as Samba does it just somehow auto-detect it and allow them through?
View 3 Replies
View Related
May 14, 2010
I want to make changes on my router bios for my server I have to go to my windows booted laptop rather than just 192.168.1.1 right here at my server. I only have to do a 360 in my chair and I am at my laptop but I don't want to. Everytime I type the gateway ip it reads off the name of my router and looks fine. But I enter my authentication info and it just returns the login window blank... something ubuntu-side?
WRT160v2 linksys wireless N router (Of course I have cat 5 running to my server)
Ubuntu 10.04 LTS running desktop ontop (because I am still learning how to navigate the console)
View 3 Replies
View Related
Sep 1, 2011
I acquired an old Compaq Evo laptop and installed Kubuntu on it. Bought a second hand wifi card, a DEXLAN IEEE802.11b (Having Googled to check it would work with Linux).
It detects wireless networks fine, and is able to connect to open ones, but I can't log into the home network with the password which works fine for Windows laptops.
I've tried every configuration of the router I can find, and followed the advice at https://help.ubuntu.com/community/Wi...untu#EasySteps but with no luck. It just asks for the password over and over again without connecting.
View 5 Replies
View Related
Dec 6, 2010
We've got a Debian Lenny + FreeRadius and cannot seem to authenticate a wireless laptop.At this point, all I want is the users file entries to work, with ClearText passwords. Eventually we'll use LDAP but we want this up first with ClearText passwords and MD5.
1. FreeRadius installed, 2.1.10+dfsg-2~bpo50+1 from Debian Backports
2. AirPort v7.5.1, set up for WPA2 Enterprise, ip 10.10.10.75
3. Apple OSX laptop, 10.5.8
When running 'freeradius -Xxx' from the Debian cli I can see the authentication fail as though the OSX machine (or the AirPort router?) isn't passing along the password (from the FreeRadius cli run).Additionally, the OSX machine always prompts me for an SSL Cert to use, but with MD5 checkmarked as the only option in the 802.1x networking screen, this shouldn't be happening, making it more difficult to tell where this problem lies.The OSX machine keeps cycling through "Authenticating" and "Authenticating with MD5", and then settles on "AirPort has a self-assigned IP Address..." (meaning the laptop, not the AirPort wifi router)
View 1 Replies
View Related
Sep 9, 2009
I'm using Debian Lenny and installed wicd package.It does not ask me for the credentials and i can't find where to define them?!
View 1 Replies
View Related
Jan 23, 2011
I switched to the b43xx (lp-phy) driver, as opposed to the broadcom STA driver which I previously had. I have dell 8312b/g lp-phy(mini) wireless card.
I have the wireless detection, but when I attempt to connect to Fios WiFi it continuously asks for my WEP (I have the correct WEP and I have typed it in correctly) and fails to connect.
I've read about the driver and firmware on linuxwireless and kernel.wireless. org.
http://pastebin.com/w44Xbgw3 (lspci -nnk output)
http://pastebin.com/C5BDhgZ9 (iwconfig output - this printed while trying to access the network)
Why is this happening? How can I fix this?
View 1 Replies
View Related
Jul 15, 2009
I can't get my Broadcoam BCM4322 to connect to a protected access point. I've tried the drivers from rpmfusion, and tried to build the module with the source+binary package from Broadcom, all with no luck. The failure seems to happen during the WPA negotiation.
I haven't tried connecting to an unsecured WiFi access point.
When booting this same laptop to Kubuntu 9.04, it can connect to secured, so it is possible under linux.
Here's output from lspci, and the tail of the log while KNetworkManager is trying to connect the device.
lspci | grep -i network
00:19.0 Ethernet controller: Intel Corporation 82567LM Gigabit Network Connection (rev 03)
0c:00.0 Network controller: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller (rev 01)
[Code]....
View 3 Replies
View Related
May 24, 2011
I cannot authenticate on my wireless network. it keeps asking me the WPA key (which I correctly enter everytime it asks me to). I COULD do that before rebooting. Now I can't. Nice.
What can I do? I've read somewhere that in the RC there where problems with the network applet I don't know what... can this be reconducted to that?
View 2 Replies
View Related
Nov 11, 2010
My wifes networked computer connected to the network just fine when it was Win XP. Now that Ive converted it to 10.04 (completely) it can see the network, but it just wont connect to it. I had no problem converting my computer to Ubuntu and it sees the network and accesses it great. Files, folders and hard drives are all shared. So, one computer connects great, the other does not.**I dont know what to do at this point.Here is the layout:My Comp (10.04) ---------......Main Network Comp (XP)Wife Comp (10.04) -------/The main network computer is XP as it has software on it we need that does not work in Wine. The main computer will have to stay XP. I cannot get my wifes computer to connect to the main system, although mine connects just fine. I dont know what the problem is. Her computer sees the network, but when trying to connect, it times out and says unable to connect.
View 2 Replies
View Related
Oct 30, 2010
I've moved a linuxbox from being my gateway (nat, etc) to behind a new gateway (a DD-wrt router). For transparency purposes, I'd like to continue using the old box services, and just have the gateway in front of it.
Here's what I did:
The newgateway is setup for class C, 192.168.0.0
This configuration works, but sometimes it doesn't and I haven't figured out why yet.
At sometimes, clients on the LAN get throughput rates with very little speed loss (using speakeasy speed test). They will run at 33M on the LAN, running through both the newgateway, and the oldbox, and get about 35M with directly connected to the cable modem.
Other times, it seems nothing can talk with anyone, and I am not sure why.
I know what I have done is a little unconventional, but it's a transitional thing, and I am not sure it is the cause of the problem, although it was the last things changed.
View 2 Replies
View Related
Feb 5, 2010
I have running on RHL enterprise 4. I want to configure squid users to authenticate against windows 2003 active directory. How do I go about from scratch
View 1 Replies
View Related
Aug 1, 2010
My son lost his USB Wireless stick for his Computer. I had thought I heard that if you had a second wireless router, you could use it somehow to detect the wireless router you have already set up in your home (like using a wireless card)? Is this what Ad-Hoc is? Either way, can this be done and if so how? I use a WRT54Gx2 Lynksys router and have a TRENDNET TEW-432BRP wireless router and also a spare D-link DI-514. I use ubuntu 10.04, and also wanted to know if I connected one of the router to his on the LAn port could he connect msaybe through an Ad-Hoc on my local computer here? He uses XP on his. I'm a newbie to linux and networking in general.
View 2 Replies
View Related
Nov 27, 2009
I want to configure linux CentOS 5 as a router using iptable, .Im new in linux so I need the steps to do that
View 5 Replies
View Related
Jun 9, 2010
I moved my server and network equipment, and now the wireless works but I cannot get my server online. I host a website, so this is kind of urgent.
I have a wireless router and can access the internet fine on my laptop. My server is wired & connected to the router. It sets up the networking properly.. ifconfig has an ip address, the default gateway is present. But I cannot ping google, or even the router. It says destination host unreachable.
So I go back to the laptop to check the router settings.. sometimes it likes to assign the server the wrong internal ip. But, I can't access the router settings either! The page (192.168.1.1) times out. Same with trying to ping the router. How can the laptop be online if it can't reach the router?
Oddly, ifconfig on my laptop reports an ip address starting with 99.233. It's always given me an internal address starting with 192.168. What's going on here? Is the router not allocating an internal ip? I use wicd to connect, if it's relevant.
We have a windows laptop that can only get a "local connection". Now it does sound like the router is forwarding directly to my laptop, instead of allocating internal ips.
View 1 Replies
View Related
Aug 14, 2010
I am thinking of moving the router behind a server and connecting the server directly to the internet via a modem. Are there any security issues related to doing this? or other things I should be aware of. Iptables are implemented on the server blocking access on unused ports.
View 2 Replies
View Related
