Ubuntu Networking :: Connect To Uni Secure Access Vpn
Aug 26, 2010
I used to be able to connect to my uni secure access vpn by navigating to the appropriate page, logging in and clicking "start" by "Network Connect" etc. etc.
After an update to firefox it had been failing, giving me a "session timeout" MsgBox. I have tried clearing history etc and reinstalling firefox. I have also tried different browsers with no success.
So, I have since upgraded to 9.10 and now I get "Setup Failed, Sorry" in the bottom left of the screen (where "Done" is displayed once a page has loaded)...
I am now trying a different approach. I have downloaded ncui-6.5R2.i386.rpm and unpacked it fine. I have tried running it, without success and have also run the diagnostic - I will post results below:
When I try and run ./ncsvc I get the following:
Code:
ncsvc> Failed to setuid to root. Error 1: Operation not permitted
So I did a sudo ./ncsvc , which gives:
Code:
mkdir(/root/.juniper_networks) failed: Permission denied
I am pretty sure that my password above is correct - I re-tried it and got the same message... I can definitely do, e.g., sudo apt-get update fine.
I then ran all of the tests available in ncdiag (./ncdiag -A) which gave the following info which might be useful
Code:
NC Diagnostics for Linux.
Version 1.0.
Release Date/Time: Dec 9 2009 04:36:09
[Code].....
View 2 Replies
ADVERTISEMENT
Feb 26, 2010
I was wondering how safe is to use rdp to access my linux box. I am a little bit concerning about this issue because as I read on opensuse's web site rdp is "less" secure. The thing is that I do not know how much less is this "less"
View 6 Replies
View Related
Jan 4, 2010
I have a Dell Inspiron 8600 laptop on which I recently installed Ubuntu 9.10. Most things work, but the wireless will not connect to my home wireless network (a Linksys WRT54G). (Cannot see any other WIFI antennas from here, so I don't know if it works on other networks). Ubuntu says I have an Intel PRO/Wireless 2200BG, Kernel Driver ipw2200.
When I try to look for a wireless network, Ubuntu doesn't see any. (Every other computer in the house does, Macs and PCs). I tried Connect to Hidden Wireless Network > New > and filled in the name and the WEP password that the Linksys gave me.When I select Connect to Hidden Wireless Network and select the network that I entered all the information for, the Connect button is always grayed out.
View 5 Replies
View Related
Jan 16, 2010
I recently ubgraded to ubuntu 9.10 from 9.04, but I had the same problem there. I can see the secure connections, but when I try to connect to them, it tries to connect, works at it for about a minute, and then asks for the password again. This just started a week ago or so. I am new with ubuntu, so while I know that there are terminal outputs I should probably post, I don't know which ones.
View 5 Replies
View Related
Nov 2, 2010
Does anyone have a way of connecting to a secure network via a bash script?
Code:
#! /bin/bash
sudo su
iwconfig wlan0 stop
iwconfig wlan0 essid NETWORK_NAME
iwconfig wlan0 key NETWORK_KEY
iwconfig wlan0 start
View 2 Replies
View Related
Nov 12, 2010
I have been using Ubuntu for quite a long time and I never got around fixing this particular wireless problem. I have tried Network Manager as well as Wicd. I am never able to connect to a secure network (WPA). When I use Network Manager, it just tries for a long time and gives up. As for WiCD, it again tries for a long time and finally says "Bad Password". Of course, the passkey is correct. When I connect to an unsecured network, it goes through just fine. I have a Dell Inspiron 1545 which uses a Broadcom 43xx Driver.
View 3 Replies
View Related
Feb 7, 2010
They are running Kubuntu. How to access their desktop from my home or office using Internet. Logically I remembered about kfrb and X11-vnc. But both of them need some approach to provide security. I'd like if someone could give me some pieces of advice on choosing the simplest and better approach:
To secure kfrb or x11-vnc is simpler or better to mount a vpn or to use an ssh tunnel? Is there any other solution? My pearents ISP use DHCP, so I think it would require some service like dyndns or similar...
View 2 Replies
View Related
Apr 3, 2010
I'm trying to setup OpenVPN in order to connect back to my home network while traveling for secure browsing and such. However, before I can even start trying to set that up I tried to see if I could open port check my computer through the net. And I'm having a hard time doing that.
As far as I can tell, here are my roadblocks:
1. Is ISP (Qwest) blocking my ports?
2. Is my modem doing the proper port forwarding and firewall?
3. Is my router doing the same?
4. Is my firewall on the computer allowing the request?
To minimize sources of error, I've turned off my local and router firewall and setup my router to forward ports. I'm not to familiar with my modem, but I'm pretty sure that the firewall is turned off by default and I think I've done port-forwarding correctly. But still no success when doing an open port check. At this point I don't know how to diagnose the problem.
View 2 Replies
View Related
Jan 14, 2010
I have successfully installed CISCO VPN CLIENT the latest on ubuntu karmic was a mission but it is installed.my latest hurdle i face is that when i am on my companies LAN network i can connect to the VPN client however when go off the LAN and connect and try to connect to the VPN client i get the message the VPN susbsytem is not started and then UBUNTU freezes and the only way to get my pc working again is to do a hard restart.I have trawled the net looking for a answer with no luck.
View 1 Replies
View Related
Aug 20, 2010
What's the command to access a secure shell?
View 2 Replies
View Related
Dec 20, 2010
My better half spilled some coffee on her 8month old macbook and it decided not to work anymore. Apple says it will cost around $800 or more to fix, we wont be paying that, Ill be finding a logic board or service somewhere online now that our warranty is shot and going that route.But before I send the macbook off anywhere I need to pull some data off the HDD. I was able to plug the HDD into my Linux box(internally, I dont have an external enclosure). I was able to mount the drive and copy the directories I wanted to the HDD on my linuxbox.
But Im unable to to access the directory from the terminal or from the file browser, I get an access denied message. Because I know the username and password for the macbook is there a way I can use that to gain access to the directories?Google got me this far, but when I googled "access locked directory ubuntu" or any variation of that with the terms linux and osx thrown in there for good measure.
View 3 Replies
View Related
Mar 4, 2010
1) I connect to the internet on a wireless router from my isp.
2) I use an older router for my media server (pc) to my ps3. The router given to me from my isp is the only one I can use to connect to the internet, yet it has the worst UPnP support (ie: none).
So with this current setup, I have to disconnect from the the wired network to be able to access the internet. So how can I access the internet while still connected to the wired network?
View 7 Replies
View Related
Mar 25, 2010
i've finish install driver for my wireless adapter and the result like this:
Code:
rapc0d@rapc0d-laptop:~$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
[Code].....
View 1 Replies
View Related
Apr 15, 2010
I just installed the wicd network manager and when i was setting it up it said it couldn't find the ip address so when i input the address its saying it can't connect to a wireless access point. I am using wireless that has worked with the default network manager but will not work with this one.
View 1 Replies
View Related
Oct 7, 2010
I have wireless G and N access points in my house. The N network is set to allow only N connections. I have a Lenovo laptop with a Intel Wireless N chip in it, and after one of the 10.10 updates it stopped connecting to my N access point. The G access point works just fine.
The logs for the Wireless N access point alway show "Bas Password." I am having the same problem with either NetworkManager or wicd.
View 2 Replies
View Related
Nov 30, 2010
I installed it alongside Win XP, using Wubi, and it seems I use Ubuntu 10.04.Everything worked out as expected, and my wired internet connection works like a dream.However:My wireless connection seem a little buggy.I can see all networks (except WPA2) so even if I want to fix the WPA2 problem, I'd rather just open my network for now.
So my network is now open, I see it in the NetworkManager list, and as i try to connect, the following happens:The wireless symbol start flashing. From here it keeps flashing, untill it gives up.I use RT2870 drivers, and D-Link DWA-140 USB wireless adapter.
It goes without saying I am a freshman regarding Linux, so if anyone knows what to do, and cares to take the time to tell me, please do tell me in a detailed manner.I do know the basics of the Terminal, and yes, I do know how to copy/paste commands I find linux way more satisfying than Windows so far ... And thanks in advance for giving away your time More info can be given upon request (You might have to explain how to find that specific info)
View 1 Replies
View Related
Dec 20, 2010
I'm running a server using ubuntu 10.04 x64. I want to disable access of groups to "bin" folder so they cannot execute commands.
[info: actually because of a bug in cPanel (the control panel I installed) Perl will give access to all hosting users to execute commands.]
So what I wanna do is to ban some groups on 'bin' folder, for example 'my_group1' and 'my_group2" cannot access bin but 'my_trusted_group' can access it. How is it possible?
View 1 Replies
View Related
Mar 1, 2009
I can connect to unsecure routers, but not to any secure routers. NetworkManager doesn't seem to work and neither does anything else I try. I have tried with WPA supplicant but to be honest I have not a clue what to do. I have an Atheros ar5009 card and I'm currently using the ath9k module. Lan works just fine. But my wireless doesn't.
wlan0 IEEE 802.11abgn ESSID:""
Mode:Managed Frequency:2.462 GHz Access Point: Not-Associated
Bit Rate:1 Mb/s Tx-Power=23 dBm
Retry min limit:7 RTS thrff Fragment thr=2352 B
Encryption keyff
Power Managementff
Link Quality=92/100 Signal level:-36 dBm Noise level=-95 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
I have updated everything it seems like, but nothing I do seems to work. I have been at this for almost 3 weeks already hoping for a break and so far nothing.
View 9 Replies
View Related
May 13, 2010
i believe it is a wpa_supplicant problem. running ubuntu 10.04 on a toshiba netbook. i have my account which cannot connect to internet, wicd returns an error that it cannot obtain ip address. cannot even connect to a unesecure network for that matter. if i switch users to another user and do the quick switch users i can get internet then i switched back to my main account and here i am postings. how do i begin to hunt down the problem logs, settings how do some of you begin to hunt down the cause of this and where it would be located.
View 1 Replies
View Related
Nov 25, 2010
I've been searching for the exact set of tools to accomplish what I need. I was once at a LANparty. I used my webmail account and I think someone stole my password. I realized that the LAN used hubs instead of switches.
So next time, I thought I could run a server at home, which would allow me to connect with SSL (??). Then I would be able to connect to whatever website knowing that I was secure between myself and my home computer. I guess I would need to have a key before a secure connection could be made. Otherwise a "man in the middle" kind of exchange could take place.
So I guess I would need a VPN between myself and my home computer. Then my home computer would act as a proxy to allow me to surf securely. I'm not sure if these are the correct terms to use. Does anyone know what type of server I'm looking for?
View 1 Replies
View Related
Oct 27, 2010
At work, we (like almost everyone) are still full-on windows. I am currently trying to get away from windows because I am not a fan. my current windows machine (different from my Ubuntu machine) is accessing the wireless network fine, and there are no obvious problems there. Also, my Ubuntu machine can access my wireless network at home, so I know there are no driver issues. I set up the connection for the Ubuntu machine, and it seems to be connecting OK. I can ping internal IPs and by all statuses, the connection to the router is functioning. However, when I attempt to load a web page or ping a domain or external IP, it fails. I tried to ping the IP, thinking if that worked, it's probably the DNS, but pinging both domains or IPs fails. I have looked around at forums and posts, but none of them seem to match my issue (that's probably not true, but I am struggling to see the commonality).
Here are the results of "netstat -r":
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.45.0 * 255.255.255.0 U 2 0 0 wlan0
link-local * 255.255.0.0 U 1000 0 0 wlan0
default 192.168.45.5 0.0.0.0 UG 0 0 0 wlan0
And here is "ifconfig":
wlan0 Link encao:Ethernet HWaddr 74:f0:6d:XX:XX:XX
inet addr:192.168.45.49 Bcast:192.168.45.255 Mask:255.255.255.0
inet6 addr:fe80::76f0:6dff:XXXX:XXXX/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]....
View 3 Replies
View Related
Jan 20, 2011
I have had a heck of a time trying to get my laptop running ubuntu to connect to my home network. I have managed to get it to work at my university which would seemingly be more difficult than getting it to work at home, so I know for a fact it isn't a hardware or driver issue. If I try to connect via ethernet cable from my router, it detects that I connected the cable but says "disconnected" and never lets me connect. If I SKIP the router and go from my modem directly to my laptop via ethernet cable it works great.
Using the wireless network tool I can see all of the wireless connections in my area. When I go to connect to my network it prompts me for the WEP key and when I enter it and hit connect it just keeps cycling and eventually times out and finally again prompts me for my WEP key. I know this network works as it works just fine on my Windows 7 partition. Another interesting note - both my wireless and ethernet connections both worked flawlessly and stoopid easily on the live cd but don't after the full install.
If I manually enter in the information for my wireless through IPv4 settings and enter in the Address,Netmask and gateway I can connect to my network - but then I have no active internet connection. Same deal with my wired connection. Is this because choosing this manual method grays out the DHCP?
View 5 Replies
View Related
Apr 26, 2011
10.04 in a couple of identical lenovo laptops (of friends) suddenly have stopped connecting successfully to wireless, coinciding approximately with a mains power socket fail at the modem router, now fixed. presumably the machines were trying to connect to the access point, which may or may not have been working, but themodem router was not. Now, internet connection and wireless access point is fixed ok and is back up, and i can connect wirelessly to the access point ok using an eeepc with 10.04.2 with no problem so the access point is working ok
the target laptop/s are still ok via wired ethernet, and can *also* connect to a neighbours open wireless (a british telecom so called fon network, it asks for an account password), and all local wireless networks can be seen normally, and the home access point ssid can also be seen ok. so the aptop wireless is connecting ok, but not to this particular access point now. maybe someting has got screwed up? it is wpa2 and when clicked, after a long-ish time, the authentication is requested, then given, correctly, and still not connecting, asks for authentication again etc etc. no local secure wallet is being used.
when upgrading these laptops for my friend some time ago from 9.04 i have a small recall that 10.04 had a odd thing with wireless authentication (?) bug? i have deleted the network connections gui listing for this ssid and restarted the laptop, still no joy.
View 5 Replies
View Related
Jun 24, 2010
I currently run Win 7 and want to upgrade my computer to a server to accomplish the following... I have a VPN Service. I want the server machine to connect to a VPN providing a secure connection. Then, I want all the machines in the house (windows based) to connect through the server onto the VPN connection. Hopefully this makes sense. Would it be better to stick to Windows Server 2008 or switch to Ubuntu?
View 5 Replies
View Related
Mar 15, 2010
I would like to be able to access my data file that reside on my Linux machine at home from the Internet but I don't want to open any "doors" for lack of a better word that will compromise the security of my files. I am running F11 and I am using cable broadband and a Linksys router.I have been able to get ssh working with OpenSSH while I am at home but I don't really need or want to ssh remotely, I would rather setup what I think is called an ftp. I just want to be able to up and download files to my Linux machine.
View 6 Replies
View Related
Dec 21, 2010
I'm running a server using CentOS 5 x64 I want to disable access of groups to "bin" folder so they cannot execute commands. [info: actually because of a bug in cPanel (the control panel I installed) Perl will give access to all hosting users to execute commands.] so what i wanna do is to ban some groups on 'bin' folder, for example 'my_group1' and 'my_group2" cannot access bin but 'my_trusted_group' can access it.
View 1 Replies
View Related
Jun 22, 2011
I have a compaq pressario v6000 with broadcom wireless card bcm4312. I was running Suse 11.3 and one day the wireless stopped working so after several hours googling I gave up and installed 11.4 but I have exactley the same problem I can connect to my bt openzone or btfon network but not to my own secure network I have tried everything I can think of including disabling security settings on my homehub but I can't get it to work at all I have used network manager and traditional I just can't get it to work.
View 6 Replies
View Related
Sep 22, 2010
Recently I had installed Ubuntu 10.04 in which I had connected to the internet by way of terminal (pppoeconf) and I could access any site with ease.But one fine day suddenly I could not access the net, I try to locate the notification icon (network manager),but could not find it.I did this and that,googled it trying to find the solution but alas to my disappointment I had to format it.
After reinstallation of Ubuntu I connect the internet by way of editing connection on panel and i could access the net. The problem is that I could not access some site especially org site e.g Home - Desiring God so can anybody guide me in how to connect in most better way.
View 5 Replies
View Related
Oct 10, 2010
I just installed Lucid Lynx Ubuntu on my computer. I love it, but I do not see how to configure my dial-up modem and connect. I'm hoping it's still possible. Here's my hardware.
333mHz Pentium III
Lucid Lynx 10.04 LTS
US-Robotics 56K Faxmodem External
256mb RAM
ISP OmniLEC
View 1 Replies
View Related
Nov 8, 2010
I have Dlink Wireless G Access Point.
I can connect to my access point to surf internet. I setup my Dlink access point (password, network name, etc) in Vista by visiting "http://dlinkap/" in my web browser.
In ubuntu, I can connect and surf the web/internet but i cannot access the setup page.
When I try to type the "http://dlinkap/" to my browser then the browser will redirect it to google search.
I try 192.168.1.1, I can access my linksys router. but my dlink access point, i cannot access the setup page.
View 8 Replies
View Related
