Ubuntu Networking :: VPN Cannot Connect When On 3g Access?
Jan 14, 2010
I have successfully installed CISCO VPN CLIENT the latest on ubuntu karmic was a mission but it is installed.my latest hurdle i face is that when i am on my companies LAN network i can connect to the VPN client however when go off the LAN and connect and try to connect to the VPN client i get the message the VPN susbsytem is not started and then UBUNTU freezes and the only way to get my pc working again is to do a hard restart.I have trawled the net looking for a answer with no luck.
View 1 Replies
ADVERTISEMENT
Aug 26, 2010
I used to be able to connect to my uni secure access vpn by navigating to the appropriate page, logging in and clicking "start" by "Network Connect" etc. etc.
After an update to firefox it had been failing, giving me a "session timeout" MsgBox. I have tried clearing history etc and reinstalling firefox. I have also tried different browsers with no success.
So, I have since upgraded to 9.10 and now I get "Setup Failed, Sorry" in the bottom left of the screen (where "Done" is displayed once a page has loaded)...
I am now trying a different approach. I have downloaded ncui-6.5R2.i386.rpm and unpacked it fine. I have tried running it, without success and have also run the diagnostic - I will post results below:
When I try and run ./ncsvc I get the following:
Code:
ncsvc> Failed to setuid to root. Error 1: Operation not permitted
So I did a sudo ./ncsvc , which gives:
Code:
mkdir(/root/.juniper_networks) failed: Permission denied
I am pretty sure that my password above is correct - I re-tried it and got the same message... I can definitely do, e.g., sudo apt-get update fine.
I then ran all of the tests available in ncdiag (./ncdiag -A) which gave the following info which might be useful
Code:
NC Diagnostics for Linux.
Version 1.0.
Release Date/Time: Dec 9 2009 04:36:09
[Code].....
View 2 Replies
View Related
Mar 4, 2010
1) I connect to the internet on a wireless router from my isp.
2) I use an older router for my media server (pc) to my ps3. The router given to me from my isp is the only one I can use to connect to the internet, yet it has the worst UPnP support (ie: none).
So with this current setup, I have to disconnect from the the wired network to be able to access the internet. So how can I access the internet while still connected to the wired network?
View 7 Replies
View Related
Mar 25, 2010
i've finish install driver for my wireless adapter and the result like this:
Code:
rapc0d@rapc0d-laptop:~$ iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
[Code].....
View 1 Replies
View Related
Apr 15, 2010
I just installed the wicd network manager and when i was setting it up it said it couldn't find the ip address so when i input the address its saying it can't connect to a wireless access point. I am using wireless that has worked with the default network manager but will not work with this one.
View 1 Replies
View Related
Oct 7, 2010
I have wireless G and N access points in my house. The N network is set to allow only N connections. I have a Lenovo laptop with a Intel Wireless N chip in it, and after one of the 10.10 updates it stopped connecting to my N access point. The G access point works just fine.
The logs for the Wireless N access point alway show "Bas Password." I am having the same problem with either NetworkManager or wicd.
View 2 Replies
View Related
Nov 30, 2010
I installed it alongside Win XP, using Wubi, and it seems I use Ubuntu 10.04.Everything worked out as expected, and my wired internet connection works like a dream.However:My wireless connection seem a little buggy.I can see all networks (except WPA2) so even if I want to fix the WPA2 problem, I'd rather just open my network for now.
So my network is now open, I see it in the NetworkManager list, and as i try to connect, the following happens:The wireless symbol start flashing. From here it keeps flashing, untill it gives up.I use RT2870 drivers, and D-Link DWA-140 USB wireless adapter.
It goes without saying I am a freshman regarding Linux, so if anyone knows what to do, and cares to take the time to tell me, please do tell me in a detailed manner.I do know the basics of the Terminal, and yes, I do know how to copy/paste commands I find linux way more satisfying than Windows so far ... And thanks in advance for giving away your time More info can be given upon request (You might have to explain how to find that specific info)
View 1 Replies
View Related
Oct 27, 2010
At work, we (like almost everyone) are still full-on windows. I am currently trying to get away from windows because I am not a fan. my current windows machine (different from my Ubuntu machine) is accessing the wireless network fine, and there are no obvious problems there. Also, my Ubuntu machine can access my wireless network at home, so I know there are no driver issues. I set up the connection for the Ubuntu machine, and it seems to be connecting OK. I can ping internal IPs and by all statuses, the connection to the router is functioning. However, when I attempt to load a web page or ping a domain or external IP, it fails. I tried to ping the IP, thinking if that worked, it's probably the DNS, but pinging both domains or IPs fails. I have looked around at forums and posts, but none of them seem to match my issue (that's probably not true, but I am struggling to see the commonality).
Here are the results of "netstat -r":
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.45.0 * 255.255.255.0 U 2 0 0 wlan0
link-local * 255.255.0.0 U 1000 0 0 wlan0
default 192.168.45.5 0.0.0.0 UG 0 0 0 wlan0
And here is "ifconfig":
wlan0 Link encao:Ethernet HWaddr 74:f0:6d:XX:XX:XX
inet addr:192.168.45.49 Bcast:192.168.45.255 Mask:255.255.255.0
inet6 addr:fe80::76f0:6dff:XXXX:XXXX/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]....
View 3 Replies
View Related
Jan 20, 2011
I have had a heck of a time trying to get my laptop running ubuntu to connect to my home network. I have managed to get it to work at my university which would seemingly be more difficult than getting it to work at home, so I know for a fact it isn't a hardware or driver issue. If I try to connect via ethernet cable from my router, it detects that I connected the cable but says "disconnected" and never lets me connect. If I SKIP the router and go from my modem directly to my laptop via ethernet cable it works great.
Using the wireless network tool I can see all of the wireless connections in my area. When I go to connect to my network it prompts me for the WEP key and when I enter it and hit connect it just keeps cycling and eventually times out and finally again prompts me for my WEP key. I know this network works as it works just fine on my Windows 7 partition. Another interesting note - both my wireless and ethernet connections both worked flawlessly and stoopid easily on the live cd but don't after the full install.
If I manually enter in the information for my wireless through IPv4 settings and enter in the Address,Netmask and gateway I can connect to my network - but then I have no active internet connection. Same deal with my wired connection. Is this because choosing this manual method grays out the DHCP?
View 5 Replies
View Related
Apr 26, 2011
10.04 in a couple of identical lenovo laptops (of friends) suddenly have stopped connecting successfully to wireless, coinciding approximately with a mains power socket fail at the modem router, now fixed. presumably the machines were trying to connect to the access point, which may or may not have been working, but themodem router was not. Now, internet connection and wireless access point is fixed ok and is back up, and i can connect wirelessly to the access point ok using an eeepc with 10.04.2 with no problem so the access point is working ok
the target laptop/s are still ok via wired ethernet, and can *also* connect to a neighbours open wireless (a british telecom so called fon network, it asks for an account password), and all local wireless networks can be seen normally, and the home access point ssid can also be seen ok. so the aptop wireless is connecting ok, but not to this particular access point now. maybe someting has got screwed up? it is wpa2 and when clicked, after a long-ish time, the authentication is requested, then given, correctly, and still not connecting, asks for authentication again etc etc. no local secure wallet is being used.
when upgrading these laptops for my friend some time ago from 9.04 i have a small recall that 10.04 had a odd thing with wireless authentication (?) bug? i have deleted the network connections gui listing for this ssid and restarted the laptop, still no joy.
View 5 Replies
View Related
Sep 22, 2010
Recently I had installed Ubuntu 10.04 in which I had connected to the internet by way of terminal (pppoeconf) and I could access any site with ease.But one fine day suddenly I could not access the net, I try to locate the notification icon (network manager),but could not find it.I did this and that,googled it trying to find the solution but alas to my disappointment I had to format it.
After reinstallation of Ubuntu I connect the internet by way of editing connection on panel and i could access the net. The problem is that I could not access some site especially org site e.g Home - Desiring God so can anybody guide me in how to connect in most better way.
View 5 Replies
View Related
Oct 10, 2010
I just installed Lucid Lynx Ubuntu on my computer. I love it, but I do not see how to configure my dial-up modem and connect. I'm hoping it's still possible. Here's my hardware.
333mHz Pentium III
Lucid Lynx 10.04 LTS
US-Robotics 56K Faxmodem External
256mb RAM
ISP OmniLEC
View 1 Replies
View Related
Nov 8, 2010
I have Dlink Wireless G Access Point.
I can connect to my access point to surf internet. I setup my Dlink access point (password, network name, etc) in Vista by visiting "http://dlinkap/" in my web browser.
In ubuntu, I can connect and surf the web/internet but i cannot access the setup page.
When I try to type the "http://dlinkap/" to my browser then the browser will redirect it to google search.
I try 192.168.1.1, I can access my linksys router. but my dlink access point, i cannot access the setup page.
View 8 Replies
View Related
Jan 15, 2011
I'm not exactly sure if this should be here and not in the Hardware & Laptops section, but seeing as my only problem is with WiFi, I'm guessing this is the right place. Under Ubuntu, my laptop (an Asus K42Ja, more details below) can see wireless networks normally. However, when I attempt to connect, it fails to establish a connection. Under Windows on the same laptop (dual boot), no problems are experienced.
According to this, there's a firmware bug in my wireless chip which causes connections to get dropped. I'm not getting connections at all, but I still tried the workarounds on that page with no luck. The router is a TP-Link TL-WR340G. My previous laptop, a really old one from 2003 running Ubuntu 9.10 was able to connect to that router without problems. The wireless card was Intel on that as well (but, of course, much older). The router is set up to use WPA for security. I didn't use WPA2 as I read something a while ago about problems with WPA2 and some Linux distros. Please correct me if I'm wrong here.
If anyone's curious, I'm posting this on Ubuntu, via an ethernet cable to the router mentioned earlier. Some tasty technical bits: dmesg (the latter half of the "timed out" messages is me retrying after double-checking the WPA key)
[Code]....
View 4 Replies
View Related
Mar 27, 2011
When I'm trying to access my site using Firefox I get this error: "Unable to connect
Firefox can't establish a connection to the server at mysite.com.
-The site could be temporarily unavailable or too busy. Try again in a few moments.
-If you are unable to load any pages, check your computer's network connection.
-If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web."
Then I tried to access my site using Opera and Chrome but I get the same error, that the browsers couldn't connect to it.
The site to which I'm trying to connect is definitely up. (I ask a few people and they can access it and I looked at [url] and it says that my site it's up)
View 3 Replies
View Related
Oct 23, 2009
At school can connect to my computer via SMB/Samba and VNC from the Windows Machines, but not by hostname (I still cannot VNC in at home on my desktop computer and have yet to try Samba there because I wanna setup Samba there from the comfort of my laptop and therefore need VNC first). How come I cannot access this machine by it's hostname?
View 4 Replies
View Related
Feb 18, 2010
Install Fedora 12 on my laptop and having problem connecting to access point using WEP . I complied with wireless setup with key but will not connect. Works with security disable, the router is a Westell 327W from what was Bellsouth.
View 1 Replies
View Related
May 15, 2011
I have an Intel PRO 2200BG wireless card and can connect to my router when logging in via gdm (using Xubuntu.) No problems there, connection never drops, very reliable!
But I've since had the need to shutdown X and keep a simple terminal instance open but as soon as I stop gdm the connection to the router drops. Trying to connect via the terminal using wpa_supplicant has so far been unsuccessful.
I know for a fact I'm doing something wrong, just don't know what and would appreciate some help!
Some dumps:
Code:
Code:
Code:
Code:
View 1 Replies
View Related
Jan 7, 2011
I have started a newly started a VPN-service with some friends and are offering both OpenVPN and PPTP-vpn.The OpenVPN works perfectly, but we have some problem with the PPTP.It is possible to connect to the VPN, but once connected you can't get any type of access to the outside world ( the interner ).I've googled (Ok, not I, but the tech-guy has) and havn't found any solution so therefor we try here.We are running Debian 5.0 on a XEN VPS.On the machines we've tested OpenVPN works like a charm.
View 12 Replies
View Related
Apr 1, 2011
I have 2 pcs at home. I dont have a switch so I can connect only one PC at a time to my adsl router/modem for internet access. In the past I had successfully connected the two PCs (NIC to NIC) to each other using the same ethernet cable which was supplied with my dlink adsl modem.
Recently the motherboard of on of my PC went bad so I replaced it with a new one. The problem is when I connect the two using the same Ethernet cable they won't connect. The lights on the Ethernet port won't light up. I can still connect both of them to the adsl router (NIC to Router) (one at a time).
View 5 Replies
View Related
Jan 17, 2010
I have fedora 12 installed in my laptop. Can anyone plz tell me how to connect nokia E51's modem ( via. Data Cable) to access GPRS !
View 2 Replies
View Related
Mar 26, 2010
I'm having a problem with my webdav share. I have a secure webdav folder that gets accessed via a non-standard port and requires basic authentication. I can connect and interact with it fine via cadaver. However, when I try to connect from nautilus, it says "Access was denied." To make it even stranger, sometimes I can click on the folder in nautilus (it still mounts) and access it. Sometimes not (just repeats the error message and won't show me the contents). I may not even un-mount it, but just look at other folder, then click it again and be able to access it, but again - only rarely.
I asked a friend to try connecting from his windows vista computer and it would not work. It would not work from my windows XP virtual computer either. However, it mounts and works just find from my work computer (also Windows XP).
So it seems to be a 50/50 chance that the drive will mount on any given computer/system and work. Do anyone know what the problem may be? I'm guessing user permissions, but I can't figure out what.
I've made sure the webdav folder is owned by www-data and www-data has read access to the password file as well.
When I try connecting from nautilus, I get this in the log file:
Code:
Here is one of the (many) sites I've tried looking at: [url]
View 4 Replies
View Related
Jun 12, 2010
My wireless (Toshiba laptop, 10.04 64 bit) is just hanging when trying to connect. It was working fine but now nothing. My Wireless antennae is on and my other laptop can connect with no problems. I have restarted the router and the laptop twice.
View 1 Replies
View Related
Dec 31, 2010
I managed to configure my W890i phone to get access to internet through an ubuntu-based computer. It's very easy to use the phone to give internet access to the computer, but the opposite is quite more tricky. For that I've done the following
----On the phone---
-Set the USB network option to "through computer", so that the phone uses the computer's internet connection and not the opposite.
-Decide and set "Shared Network" parameters: user, pasword and workgroup.
-In "conectivity-> internet connection" set "allow local network" to "yes"
----On Ubuntu 10.04---
-Install samba, samba-client, smbfs, smbclient, firestarter and dhcp3-server
-Configure Samba (System-> Administration-> Shared folders): same workgroup as in the phone, add new user (the phone), passwd this new user. In my case the user was called "w890i" and the password given was the same.
-Once the phone is connected to the computer through USB (then select "phone mode"), a new connection appears in NetworkManager: usb0.The aim is to create a shared network that gives internet access to this device. Edit the IPv4 parameters of this new connection, set them to Manual and give an IP adress (192.168.0.1) and a subnet mask (255.255.255.0); the rest of the fields are left empty.Connect this network.
-Set firestarter to use dhcp3: sudo ln -sf /etc/init.d/dhcp3-server /etc/init.d/dhcpd
-Launch firestarter and follow the wizard. Set "allow internet shared connection", choose the device for the primary internet access, and then the device for the shared network (usb0). Then change the settings for firestarter: activate DHCP for local network, set IP to the one we gave before (192.168.0.1).
-Open dhcp3-server config file sudo gedit /etc/default/dhcp3-server And set INTERFACES="usb0"
-Set the policies of firestarter: in incoming connections, allow connections from the IP adress given to the phone (192.168.0.1). Then add rules for the ports that need to be open for this connection. I opened HTTP, HTTPS, SMB, SMTP, POP3, IMAP, IMAPS, DHCP for all the connections in the local network.
-Apply policies and start the firewall.
------------
After all this, the phone can access the internet through the computer. Two problems appeared:
1. I couldn't get access to https sites, like webmails. The phone gave a "communication error". But then I tried with Opera instead of the browser built in the phone's firmware, and I could finally get to https sites.
2. I couldn't retrieve mail, neither POP nor IMAP nor IMAPS. I thought it was a firmware problem again, and I tried out several mobile phone email clients written in java, but none of them worked.
So this is at the moment the problem. If I connect from the phone to the internet directly through 3G, the email clients work for all my accounts. I don't think it's a firewall problem, because the ports are opened for this connection
View 3 Replies
View Related
Jul 6, 2011
I connected my laptop running with Ubuntu 11 in the LAN but I couldn't access internet.But I could ping to the other computers connected in the LAN. I tried the same thing with windows 7 in the same laptop and I could access internet.
View 1 Replies
View Related
Nov 2, 2010
I am unable to connect to wireless network in ubuntu 10.10.i have noticed that the iwlagn driver isnt been used by anything.
View 9 Replies
View Related
Jan 10, 2011
in linux world and have recently downloaded and installed ubuntu desktop 10.10i cannot connect to both wired and wireless ethernet on my laptopit tries to connect but fails in 30 seconds , it says"disconnected" while i am able to connect to the same in windows i have broadcom 4315 and i have tried both fwcutter and ndiswrapper but the problem persiststhe device id is 14e4:4315
View 9 Replies
View Related
Apr 6, 2011
I am trying to setup a dhcp server for my internal network. I have two NICs, a modem, and a wireless router. I have my server connected directly to my modem which is providing me with Internet access on eth1 and is working fine. I have dhcp and dns setup on eth0 which is connected to my router. The router shows that it is connected to the Internet but when the router gives a client computer an IP address, the client is unable to connect to the Internet but can connect to the router. I will post my configuration files below with my current configuration.
[Code]....
View 5 Replies
View Related
Aug 8, 2011
I can connect to the internet through wifi, but I cannot connect to anything on my network. I have a printer and a NAS, so I would really like for this to work again. I have a dell laptop with a Broadcom card.
View 9 Replies
View Related
Aug 15, 2010
I had put my computer on standby and when i restarted it, it powered off within a few seconds. I turned it back on and after that i've lost connectivity to internet on Ubuntu 10.04.
However I have VMware (XP) installed and internet/network works on that. I'm a newbie with Linux.
Here are some outputs:
I have tried to edit the connection using System>Preferences>Network Connections. I entered manual settings for IPV4, but whatever i enter there, it doesnt get reflected when i type ifconfig in the terminal window. I tried setting it to Automatic DHCP as well. Doesnt work.
View 1 Replies
View Related
