Can you "split" a network interface in Ubuntu, similar to how airmon-ng lets you use your wireless card in managed and monitor mode, by making another interface out of the same hardware? I know it'd be slower, but I'd still like to do it.
View 4 RepliesI've installed backtrack 3 in a vmware machine also i'm using a tp link adapter for to do it this is the model tl- wn422g 54 mbps high gain i have wifi internet i can surf the internet (inside backtrack) but the problem starts when i type in the kernel console airmon-ng nothing appears in interface channel etc then i try iw config and also nothing detects and it's frustrating because i'm connected to the internet.
View 2 Replies View RelatedI have 2 wlan cards. wlan0 and wlan1. wlan0 is in AP mode(Master mode) using hostap. wlan1 is connected to another wireless network and is in Managed mode. Now I want to make a bridge between wlan0 and wlan1. I do it like that:
ifconfig wlan0 0.0.0.0
ifconfig wlan1 0.0.0.0
brctl addbr mybridge
brctl addif mybridge wlan1
can't add wlan1 to bridge mybridge: Operation not supported
It doesnt work, because wlan1 is in managed mode. But Windows 7 can bridge 2 Wlan cards when one is AP and another one is STA. How to do it in Linux?
Running Ubuntu 10.10 on Hp Mini 1030nr My wireless card is a Broadcom BCM4312. I have the b43 driver installed. When I disable networking I can change to monitor mode but then it changes back to manage mode when I enable networking again. I tried using airmonNG but it;s not working.
View 1 Replies View RelatedI would like to change wireless mode on my network card. When i type in iwconfig in terminal so i get abg I would like to have only a mode active. How do i do?
View 2 Replies View RelatedI'm trying to get a wireless PC (PCMCIA?) card working under 10.04 desktop. It does not seem to be recognized by nm-applet and I cannot see any particular reason why. I have disabled the built in wireless (Intel 2200) in both BIOS and by blacklisting the appropriate module so there should be no interference from that. The card is a Linksys WPC300N V1. It has Power and Link/Act LEDs both of which remain dark.
Here's the information I have collected regarding the card:
lshw:
Code:
hbarta@willow:~$ sudo lshw -c network
*-network
description: Ethernet interface
product: 82540EP Gigabit Ethernet Controller (Mobile)
[Code]....
I saw a comment about 'You need to have "managed=true" for NetworkManager to bring the interfaces up. in '/etc/NetworkManager/nm-system-settings.conf and did so but I see no change.
I understand that modules must be compiled to support network-manager but I would expect that to be the case with modules that ship with 10.04. I don't see any obvious indications for why this is not coming up with network-manager. Is there something I;m overlooking or something else I need to do?
I am trying to work my wireless card on backtrack 4. I use backtrack 4 through VMware. I have a netgear wg11v2 wirless card and when i try typing in airmon-ng no wireless cards show up. I made sure the my wireless card was connected to VMware but for some reason it does not show up. I've look around on many post and still have not found a solution I downloaded rtl8187_linux_26.1010.0622.2006 but not sure how to or where to install it or if I really even need it please someone been at this for about two weeks.
View 4 Replies View RelatedI like to test my network often. Until recently, I've been doing so on my old Ubuntu 6.06 laptop... the problem is It's too slow (1.06 GHz single Core ), and old, (designed for Win 2000) to really be effective any more. So, recently I bought a new laptop...one with a Dual core Processor, and twice the speed. Anyway, I'm running Fedora Core 10 X86_64 on it. My problem is as follows:
Although I do have MadWifi installed, for some reason, I still can't put my Atheros based Netgear WPN511 into monitor mode. (in the Network configuration window, it says "Atheros Communications Inc. Atheros AR5001X+" I'm not sure what it means but I'll put it in in case it helps) does MadWifi not work with Fedora? if not, is there a Fedora 10 (X86_64) alternative?
I had aircrack-ng running on my old version and it worked well in the old version of linux but now when i run the programme and put my card in monitor mode it throws me the following message:
Found 5 processes that could cause trouble. If airodump-ng, aireplay-ng or airtun-ng stops working after a short period of time, you may want to kill (some of) them!
PID Name
677 avahi-daemon
678 avahi-daemon
701 NetworkManager
765 wpa_supplicant
2037 dhclient
Process with PID 2037 (dhclient) is running on interface wlan0
Problem:I got a new Acer Aspire 8935G notebook, installed Ubuntu 9.10 on it and everything is fine, except the fact, that it wont detect any network interfaces (or how to call it So there are no ethernet or wlan connections available in the network-manager..
lspci gives me following lines:
joe@IGNAZ ~ $ lspci
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev
[code]...
I am running Lucid Lynx, kernel 2.6.32.23 generic, I have a card with the Broadcom BCM4311, with the STA Linux Wireless driver. I have no idea how to get monitor mode to work with the Aircrack-ng suite's Airmon-ng command. I use the command: sudo airmon-ng start eth1
And I get this output: Found 5 processes that could cause trouble. If airodump-ng, aireplay-ng or airtun-ng stops working after a short period of time, you may want to kill (some of) them!
PID Name
883 NetworkManager
893 avahi-daemon
896 avahi-daemon
931 wpa_supplicant
[Code].....
the default for /etc/network/interfaces? I believe I screwed it it up because I can detect my wireless, it just won't allow me to connect to it. The settings in the /etc/network/interfaces are all messed up. I'm running Ubuntu 9.10.
View 2 Replies View RelatedI can't get my wireless into monitor mode. I;m running ubuntu 9.1 karmic It connects fine to wireless networks. But when i do: sudo iwconfig wlan0 mode monitor. I get: Error for wireless request "Set Mode" (8B06) :SET failed on device wlan0 ; Device or resource busy. I can only see wlan0 (wmaster0, eth0), not ath0 or wifi0 mentioned elsewhere, in wireshark. I only see my own ip and packets coming to and from that. my system tells me i have an atheros ar9285 chipset in place.
View 2 Replies View RelatedIf I try to add a new interface (eth1) to /etc/network/interfaces, I get
Code:
* Reconfiguring network interfaces... SIOCSIFADDR: No such device
eth1: ERROR while getting interface flags: No such device
SIOCSIFNETMASK: No such device
[Code]...
How do I add 2 interfaces and get anyone of them to work, as available ?
I'm a student who is working on a wireless research project. I have a madwifi driver for Atheros chipset on Debian Linux. With having the wireless interface get into monitor mode, I want to forward the captured packets from the wireless interface to the other Ethernet interface so that a different computer which is connected to this machine via Ethernet receives those packets. I checked that alll packets are received in the wireless interface using TCPDUMP. I tried to forward those packets with IPTABLES like 'iptables -p FORWARD -i ath0 -o eth2 -j ACCEPT' However, I couldn't see any packets forwarded to eth2 using TCPDUMP.
View 5 Replies View RelatedI am running ubuntu 9.04 in my laptop. I want to change the wireless card mode of my laptop to master mode so that it can work like a access point.
View 1 Replies View RelatedI am using ubuntu 9.10 on my desktop having a belkin wireless usb card. I want to change the mode of it to master mode. How can I do it?
View 3 Replies View RelatedI have installed qemu/kvm and created a Bridged network connection which works just fine(Windows 7 VM won't work in NAT mode.)
But when I try to use NetworkManager it says that I have no network connection because the network isn't managed, (I set the settings in ifcfg-br0 and ifcfg-eth0 to be managed)
The real problem is that now I can't use my VPN connections (I have many) in NetworkManager.
Is there a way to have both of these pieces of functionality?
I am using FC14
The problem with my wireless network. I have Dell DV6 Pavilion 2115 eg laptop and i installed Ubuntu 11.4 and internet and wireless worked, until i reboted my system it has disapear. I cant no longer to connect to a wireless network. It dont shows me any wireless network. My wireless card is Atheros AR 9285 802.11b/g/n Wifi Adapter
View 9 Replies View Relatedmy wireless home network is not recognized by my network card (RealTek RTL8190 mini PCI). The post was as follows: "I am using a new computer with Windows 7 , Athlon quad core 2.60 64 bit, 8GB RAM. Internet conection works fine with ethernet but ubuntu does not see my wireless network. card (RealTek RTL 8190 ID: 10ec:8190). Have searched this forum but unable to come up with a fix. I was looking for windows XP drivers to use Ndiswrapper but could not find a list of .inf files. My network is OK and works perfectly in windows and with my 2 laptops. Can anyone point me in the right direction? Additional info: install was done within Windows using WUBI to a separate partition on my HDD. I am new to this and thouroughly confused as to the procedure for installing the drivers if they are in fact available."
I am very frustrated in that I would like to use Ubuntu 10.04 but it is useless without internet connectability. I am new to linux and do not understand where to get the appropriate drivers or how to install them. I wish someone would answer this post and either give me a clue what to do or just say "give up" and uninstall ubunutu.
I use my T61 both wireless and in the dock, where I switch to the wired connection. After the latest round of updates, I seem to have lost the ability to switch to the wired network. When I turn the laptop on, I see it connect to the wireless network, but when I left click on the tray icon under Wired Network is says Device not managed. I have not made any changes to anything in the last couple weeks, besides some updates. How do I go about getting the wired network back in there?I tried to add eth0 back into System - Preferences - Network Connections, but whenever I try and add eth0, but it still says Device not managed.
View 2 Replies View RelatedFirst of all, this tutorial will use NDISWRAPPER, not b43, not wl (Broadcom STA). So, hooray for new method (actually, the only method ). Now, I don't want anyone to get scared because of bad experiences with Ndiswrapper or whatever, it's actually quite easy. I did not come up with any of this info. I'm just putting this guide together from Kacper Szczesniak's info (who came up with this method), WifiDocsDriverbcm43xxFeisty_No-Fluff from the Ubuntu Wiki, and my experience. The Broadcom STA (wl) driver has references to monitor mode in it's code, but does not have that functionality in reality. The Broadcom Windows driver on the other hand does have this capability. So, for monitor mode to work, you will need a patched version of ndiswrapper.
1) Install the Linux kernel headers:
Code:
sudo apt-get install linux-headers-$(uname -r)
2) Install the tools required to compile Ndiswrapper:
Code:
sudo apt-get install checkinstall dh-make fakeroot gcc build-essential
3) Unload current Ndiswrapper module, if running:
Code:
sudo rmmod ndiswrapper
[code]....
Seems everytime I upgrade wireless quites working.
Anyways, here's the info:-Acer Aspire One AOA150-1997
Quote:
kevin@ubuntu:~$ lspci
00:00.0 Host bridge: Intel Corporation Mobile 945GME Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GME Express Integrated Graphics Controller (rev 03)
00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03)
[Code]...
I think that's all that would be needed to help diagnose the issue. I'm kinda new to linux, and this is primarily a music machine.
Just purchased a Asus USB-N13, and having follwed a mixture of tutorials, including the readme on the driver disk, i have had no luck in getting this adapter to work.Upon using "sudo iwlist ra0 scan" the adapter can see multiple networks, however device manager is stating that the device is not managed. How can I get this sorted and connect to a network?
View 1 Replies View Relatedsetup the correct mode for my laptop-video card-monitor
Video card - ATI mobility Radeon X1600
External Monitor - Belinea b.display 2 22"
Right now the external monitor is working, but sometimes it goes black for 2-3 seconds and then works again. This happens sometimes 5 times in a row, sometimes once, sometimes none. Other issue, when I install any new kernel it doesn't work. I get weird picture on monitor.
After the use of pppoeconf, the network manager does not recognise neither the wired nor the wireless connection anymore. (It nicely did it before that) I tried to replace the etc/network manager folder with that of a different machine. Still the same. What else can I do to reset Network Manager ?
View 1 Replies View RelatedI'm having trouble getting onto the internet with ubuntu 9.04. I have just moved house and have just got the internet set up here (typing this on windows laptop with wireless). My ubuntu desktop is plugged in to the network, but in the top right hand corner when I click on the network icon I get: "Wired network device not managed"
In my old house I had a static IP. Is this anything to do with it?
My C++ program must be able to detect EVERY Wireless Network Interfaces under Linux operating system and display the interface names on the screen.How can my application achieve this?Is there any sample codes?Is there any third party libraries can do this?Notes: The detected wireless network interfaces should also include the virtual interfaces, like the one created by Aircrack-NG's Airmon-NG script.
View 1 Replies View RelatedFor some reason, i just cannot get my wireless to work in xubuntu. When i click on the network-manager applet, it only has the wired network tab and VPN connections, there are NO wireless networks displayed. I have also tried iwconfig, which returned
lo no wireless extensions.
eth0 no wireless extensions.
and lspci:
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port (rev 07)
00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03)
[Code]...
I am running ubuntu server x64 as a router. I currently have 2 LAN cards, eth0 and eth1. and I want to add wireless capabilites to the machine.I was wondering if any of you know which card I could use?I want it to be supported in ubuntu server and it must be n-draft, as it is to replace a Edimax n-draft router.
View 1 Replies View Related