Is there a way to force the Intel 3945ABG card w/ driver iwl3945 into a specific modulation mode? 802.11G for instance? Instead of the auto a/b/g I tried
Code:
sudo iwconfig wlan0 modu 11g
And got an error like the following:
SET failed on device wlan0 ; Operation not supported.
I am new to using ubuntu. I am trying to play with my WLAN by changing its modulation, power, bitrate, channel etc. When I am trying to change the modulation type i had an error like this # iwconfig wlan0 modu 11g Error for wireless request "Set Modulation" (8B2F) : SET failed on device wlan0 ; Operation not supported. so i checked for different modulation types my WLAN supports this produced an error like this.
# iwlist wlan0 modulation wlan0 unknown modulation information. I even cannot access the power types my WLAN supports. I am using Intel wireless wifi link 5100. change the modulation type and power for my WLAN?
Can't get wlan0 working:
In networkmanager the device apears unavailable.
Well, I enjoy the show Stargate SG-1, and I was wondering if there was any way I could get my voice to sound like that of a Goa'uld or Tok'ra while I am talking on Skype.
View 1 Replies View RelatedI'm having problems trying to turn on the power saving on my intel 3945ABG wireless chip with the iwl3945 module. if i remember correctly, i used to be able to have the power levels adjusted before with previous releases / kernel (i started caring about power savings back again after getting a new battery).
keying 'iwconfig wlan0 power on' returns Error for wireless request "Set Power Management" (8B2C): SET failed on device wlan0 ; Operation not supported.
And 'iwpriv wlan0 power' returns wlan0 no private ioctls
Is there something i'm missing or does the chip/module doesnt support power saving features?
until yesterday night wireless was working fine on openSUSE 11.2 After a reboot, suddenly wireless is not even shown as a possible network medium. In the network manager, the tab with "wireless" is greyed out.After going through many forum posts, here is what all I have tried.Output from various commands:
Code:
dmesg | grep firmware
[ 7.379074] IBM TrackPoint firmware: 0x0e, buttons: 3/3
[code]....
I guess that driver is not getting loaded since modprobe is giving an error which I mentioned earlier. What could be reason? Did driver crashed? Since this issue cropped up only after I rebooted the machine.
Installed openSUSE 11.3 over an existing 'very stable' 11.2 installation and started experiencing wireless connectivity issues immediately. Network Manager would show connected 100% - 92% but I would lose connectivity to mail, browser and messenger(s). This disconnect would last less than 30 secs but would occur every 2 to 4 minutes.
dmesg reported:
[ 3663.672098] iwl3945 0000:03:00.0: Failed to get channel info for channel 3 [1]
[ 3664.101085] iwl3945 0000:03:00.0: Failed to get channel info for channel 3 [1]
[ 3664.529050] iwl3945 0000:03:00.0: Failed to get channel info for channel 3 [1]
BTW Channel 3 is the channel my wifi is broadcasting on. I've tried other channels and other computers and it is only openSUSE 11.3 having an issue. I am also using WPA2. Modifying the Global Options in Network Settings from User Controlled with NetworkManager to Traditional Method with ifup seemed to stabilize most of the issues, but I do notice occasional drops. I've also switched from Network Manager to wicd to provide some UI while dealing with this issue. Since iwl3945 drivers are now in the kernel I don't know if I should try to revert to an older driver or if there is another issue.
m using redhat 5.3 i have installed a driver for wifi as per my wireless card... i checkd my kernel version , nd it is as per the requirements... but i hve a file name iwl3945.ucode how to install the driver using this file...?
View 3 Replies View RelatedI'm having problems while trying to connect to protected wireless network using iwconfig(8).
When I type in:
Things work ONLY if i DON'T input some numbers after the s: but my actual passkey has numbers.
It outputs this as an error:
my configuration(ThinkPad R61i):
I am having a heck of a time trying to find directions on networking my two computers together in order to share files. I have two machines running Ubuntu 10.10 Desktop & Netbook remix.
They are both connected to my wireless router to connect to the internet.
trying to bond two 3G modems but I cant Im really new in this matther so I really This is the error that appears
ubu@ubu-AOD255E:~$ sudo /etc/init.d/networking restart
* Reconfiguring network interfaces... Ignoring unknown interface ppp0=ppp0.
[code]....
I just got connected to Charter Cable Internet service a few days ago and I'm having a weird problem with my home network. Prior to this my network worked fine. On my network I have a desktop running Ubuntu 9.10/64 and Virtualbox with WinXP installed, an HTPC with Ubuntu 9.10/32 installed and a laptop dual booted with Ubuntu 9.10/32 and WinXP. The desktop and HTPC are hard wired to a wireless router and the laptop is wireless. The cable modem is hard wired to the router. I have samba installed and UFW is disabled. The problem is: with the cable modem turned off or on standby, all machines connect to each other and can transfer files, etc just fine but when I activate the cable modem all of the machines can connect to the Internet but the machines running Ubuntu can't connect to each other on the home network. If I boot the laptop into Windows, it can connect to the Linux machines just fine but if I boot it into Linux, it won't connect to the Linux machines but it can connect to the Internet and as far as the desktop, Ubuntu won't connect to the network but Windows running in the Virtualbox with bridged networking can connect to all of the machines.
View 2 Replies View RelatedIm trying to make an ubuntu server box my entrypoint to my networking. Meaning itll function as a server, a firewall, and a gateway. so i already installed dhcp3 and a dns server.
I have 2 ethernet cards in it. So now i wonder, should i the second card into a router's modem/wan port and make the router a switch? or should i plug it into one of the routers lan ports?
I have 3 Dell Precision M4400 machines. After getting updates yesterday or today, I get random network dropouts like crazy, on wired or wireless. On one machine I was able to turn off ipv6 in grub and reboot, and it works now. However on the other 2 machines, still have the same problems. All 3 are running 9.10 64 bit. Is there a way I can back out the updates so the network works again? Anyone else see this behavior after updates today?
View 2 Replies View RelatedI'm try to create a mobile broadband connection using my Huawei E 1550 medem. but in Network manager there is not way to select my modem in the first step ( device selection step ) the drop down menu is locked. what to do ? how to configure my modem with ubuntu ?
View 1 Replies View RelatedI do have internet cause I am using it on W7. The only thing that I have done different is I left the pc on over night so I guess it went to suspend for the first time. Then I powered off. After turning the pc back on and logging in I have no internet. Not even with the Ethernet plugged directly in. There is supposed to be a little blue light on when it sees the wireless and that is off. When I click on the networking icon in the system tray it says networking disabled. It shows no wireless. When I plug directly in I still get nothing. I'm using 10.04
View 2 Replies View RelatedOk, so I am needing some drivers and I've been googling like hell to find em, however, I can never seem to find any. My adapter model is F6D6050v1.
PS: when I try sudo ndisgtk it comes up with command not found.
I just started having a problem with my 10.04 laptop a few days ago, maybe Thursday, last week. When the computer is plugged into my home network (standard 192.168.1.1 sort of IPs) it works fine, but when I try to connect to my work network (130.15.90.XX) I am unable to pick up an IP. The router in my office is working fine, all the windows boxes can connect.
I've also noticed that when the computer is plugged in at work the notification icon for the networking indicates it is looking for a wireless connection (rather than the normal up/down arrows), even if wireless is deactivated
I can set a static IP in /etc/network/interfaces and everything works, so it seems to be a DHCP problem?
I'm using a Packard Bell Easynote Tn36 laptop, and I'm having trouble with Ubuntu 10.10 and the wireless network card, (probably because of lack of driver). I.e. it is disabled.
How can I enable it?
I input this code:
And here is the output:
Whenever I start up my laptop i do not get a wireless connection automatically. I have to rightclick network manager applet and select enable networking. After that everything works fine untill i shutdown and restart my laptop. I would like a way to change this so that my wifi connection is working whithout having to click something first..
OS:Xubuntu 10.04 LTS!
hardware: dell inspiron 6000
nm applet: 0.8.?
I have a server with two ethernet ports. I configured eth0 to be static, set at 10.1.10.148. I plugged in another router into the other ethernet port in order to configure that router. I configured eth1 to use dhcp. Using /etc/network/interfaces rather than gnome network manager. When I did this, I lost internet connectivity (internet routes through eth0 of course)
- Why did I lose internet connectivity?
In order to recover internet activity, I had to disconnect the new router on eth1 of course, and do sudo ifdown eth1. That wasn't enough however. After rebooting numerous times and pulling out my hair, I finally tried configuring eth0 as dhcp, rather than static, and this fixed the problem.
- Why didn't sudo ifdown eth1 solve the problem? What information was saved between reboots that somehow remembered that I plugged in the new router? Because my thinking was if /etc/network/interfaces was identical, and the network topology was identical, after a reboot everything should be restored, but it wasn't.
I can connect to the internet and browse. I'm wired and using DHCP on a Windows network. Updating Ubuntu or downloading programs takes hours for 52MB of updates. Why? I read some articles that mention Network Manager needs to be enabled at the .conf file. Can I edit this using GUI or command line only?
View 9 Replies View RelatedI just upgraded to natty last night, and everything is working fine except for the network manager. I can enable and configure the wireless card via bash, but the network manager widget will not manage the wireless card.
When I first boot up, the "Enable wireless" check box is greyed out. After I enable the card via the terminal, the "Enable wireless" check box becomes ungreyed, but every time I click it, it instantly unchecks itself. I feel like Currly from the Three Stoogies. Check, uncheck, Check, uncheck.. "Slaps face repeatedly."
I have Packard Bell easynote tn36 and I used to use ubuntu 10.10 and then when I upgrad it to ubuntu 11.04 the wireless doesn't work (disable) and I can't press the botton of Enable wireless.
View 9 Replies View RelatedI was having no problems (that I knew of) browsing the web since installing Ubuntu 10.10 a week or so ago. I was previously trialling Win7 as my customers will likely be using that in the future. Then I wanted to go to internode.on.net. Got the following: Quote: Firefox can't establish a connection to the server at internode.on.net. or Quote: Oops! Google Chrome could not connect to internode.on.net
As it was just after Christmas I thought it must be down, for upgrades or maintenance etc. I later tried to go to Freebsd.org; same error. I've been having a small number of other websites give the same error. I thought nothing of this until I tried it on my wife's macpro. I could log onto all the websites I wanted to and none gave any indication of having been down. Both boxes are on the same adsl connection. I still can't access internode or freebsd on 10.10 yet have been able to access every website on OSX. Now, I was only looking at them for info but am worried I won't be able to access something important. (so far everything I 'need' is working)
ping just drops out. edit: weirdest thing! I just retried and now can not emulate the problem for internode. freebsd still won't show. that is less than five minutes between problems and resolution! I hadn't even posted! But I still would like to have an idea of what is going on. Here is the ping error for freebsd: Quote:
[Code]...
I am attempting to setup and old BBSinside of DosBOXI've built one of the DosBOX Megabuilds, with the NE2000 patch.It uses libpcap in order to piggy back on top of the system's NIC. All of the dosbox side appears to be working.My system comes up, gets the MAC address i told it to use, i can load a packet driver in dosbox, all of that seems well and good. The issue, i think, is on the linux side. It's built on a Fedora 14 box. I'm getting the feeling that networking isnt getting out of the dosbox instance. Does it seem possible that fedora needs to have some config in place to link networking over to dosbox?
View 7 Replies View RelatedIve managed to install samba, I've shared a folder. I can access from a Windows 7 machine via \ubuntupublic. I can put files in the folder form the ubuntu machine and edit them on the windows box. I can put files in the folder/share from the Windows box but then I cannot edit them on the Ubuntu machine (they are read only and have a "Lock" over them). I can fix this by going to the properties of the file/folder in Windows and manually assigning "Everybody" full control (then the lock disappears and all is well.) I want read/write access to all the folders contents from both machines all the time (security is NOT a concern I WANT the permissions wide open) what am I doing wrong?
View 7 Replies View RelatedI have just finished installing 9.04 via USB onto an Acer Travelmate C110.For the record, 9.10 refused to even boot on this laptop. I used universal-usb-installer and unetbootin, both without success.The installation completed successfully, except that wireless networking is not enabled. Can someone please point me to the correct resource whereby I can get the wireless nic working.
View 3 Replies View RelatedAfter deleting part of the gnome config directories in order to reset gnome (GUI was messed up - No title bars, etc). I lost my bluetooth tethering to my Nokia N900. I cannot redo it as it always fails. Linking from phone to Laptop works, but cannot use it to link up to the internet then. Cable to the phone always worked up till now. Now I cannot get a connection as it stopped working after my upgrade to 11.04.
View 3 Replies View RelatedI am running K/Ubuntu 9.10 with an HTC Hero (CDMA) running Android 1.6.
I would like to be able to stream media from my PC to my phone. Much like what gMote does but you can play it on your phone and not just navigate.
Also, does anyone know a good way to upgrade my HTC Hero (CDMA) to 2.1?