I bought this wireless card because alot of people said it worked out of the box and it almost worked... Ubuntu recognizes it and the wireless module is activated I just can't seem to scan for networks or connect to them... So I am listing some outputs for you guys and hopefully there is an easy fix.
[Code]....
I have another question, complete beginners question. I have a HP computer that is running Ubuntu 9.10 Karmic Koala and everything works great, including the Wireless Card, a Sabrent USB-G802 WiFi USB dongle. I tried to upgrade to 10.04 two ways, off of a Live CD, and with the direct upgrade. They both installed correctly, and worked fine, but did not recognize my WiFi dongle. Is there anyway to make it work?
View 1 Replies View RelatedI am looking for a driver to use with the Sabrent PCI-G802 WiFi Ethernet card on Slackware. I found a link about this card on LinuxQuestions but the URL mentionned are no longer valid. Slackware does not seem to recognise the card on installation.
View 2 Replies View RelatedMachine is an MSI U130 netbook running Ubuntu 10.04.2 LTS 01:00.0 Network controller: RaLink RT3090 Wireless 802.11n 1T/1R PCIe interface
Code:
wlan0 RT2860 Wireless ESSID:"" Nickname:"RT2860STA"
Mode:Auto Frequency=2.412 GHz Access Point: Not-Associated
Bit Rate:1 Mb/s
[code]....
I realize that Ubuntu recognizes the card, but I'm not sure why it's not picking up any networks that are around and says "disconnected", even though I've made sure that the wireless network light is enabled on the netbook.
I'm running Ubuntu 10.04 server 64bit. I'm trying to get my ASUS PCE-N13 wireless PCI card working for searching and connecting to wireless networks. But I have no networks applet appearing in the panel. system->preferences->sessions has the Network Manager enabled The Notification Area is added to the panel. system->preferences-Network Connections-->Wireless[tab] shows a pink box, with no available connections.
[Code]....
I have a Linksys AE1000 wireless adapter and I used the post found here to install the drivers.I've figure I installed the drivers successfully because when I use "iwlist ra0 scan" I get a listing of available networks.The problem is, I can only connect to unsecured networks. For instance,
Code:
sudo iwconfig ra0 essid "unsecure network"
The above command connects me but the one below doesn't
[code]....
I can not connect to wifi networks, i can see them but not connect.
My wifi device is:
I updated to KDE 4.7 today with MUCH trouble muon hung at towards the end of the updrade at 100% so i had to force quit with " sudo ksysguard" it refused to boot into the desktop so i had to complete the upgrade from the terminal/safe mode when it finished i could not get my wireless to work my drivers is installed properly and i have tried toggling the wireless switch, much to my dismay but nothing seems to work. i can't scan for networks and the network-manager app just reports "WLAN Interface: Error: Invalid state"
View 2 Replies View Relatedi have a printer with a wireless connection and a router with wireless capabilities can i use it some how?
View 3 Replies View RelatedI have an hp dm1z and ubuntu 10.10 64bit. After I suspend (close the lid) and wake it up (open the lid) at a different location with a network connection (wired or wireless), my system always fails to connect. I need to reboot and then it sees the network and connects fine. I have tried /etc/inet.d/networking restart, but nothing changes. The only exception to this rule are two networks that have WPA security settings and are stored. I can always switch between those two. I have tried ifconfig eth0 up & down and restart networking. I have also tried to connect manually (dhclient) and no success. None of these work. I am including the output of lshw -C network.
lshw -C network:
*-network
description: Ethernet interface
product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller
[code]....
I have an MSI Wind U100 netbook running Maverick, and it has a Realtek RTL8187SE Wireless controller according to lshw. My computer can "see" some wireless networks where they are present, meaning when I click on the little network icon at the top of my screen it shows the available networks. But when I click on them to connect, the icon does its little "connecting" motion, but I never receive any message saying "Connected" and when I open Firefox and try to browse to google.com, it says "Server not found"
View 8 Replies View RelatedI have an ethernet card connected to my LAN and a USB cell modem internet connection. I am running ubuntu 10.10. The problem is this: I can use either network, but only am connected to one of them. If I connect to both at the same time my speed drops to zero.f I disconnect one, the other starts working. I have done a lot of searching and reading, but it looks like I don't know how to find what I am looking for.My LAN was setup as 3 WinXP computers peer to peer. One of those computers was replaced by this one that I am having trouble with (computer A). Another one was replaced by one that is not yet on the network (computer C).Computer B dual boots Win XP and ubuntu 10.4. Mostly it ns xp for Quickbooks and BobCAD, also it is connected to the printer. My router is setup for DHCP
View 2 Replies View Relatedi installed network driver using ndiswrapper so the network driver is all installed
packages for ndiswrapper:
ndiswrapper-common version: 1.9
ndiswrapper-utils version: 1.9
ndisgtk version: .8.5
[code]....
then i did
command: sudo ifconfig wlan0 up
contents: SIOCSIFFLAGS: No such file or directory
[code]....
We have two networks,one is 10.0.0.* with mask 255.255.255.0 & the other 20.0.0.* with mask 255.255.255.0 and one linux(RHEL5) PC with two network interface eth0,eth1.(configured as Router)
eth0 is 10.0.0.1 and eth1 is 20.0.0.1
we have enabled IP_Forward using "sysctl w net.ipv4.ip_forward=1"
cat /proc/sys/net/ipv4/ip_forward is 1
but unable to ping from one network to other network.
two networks are connected to Linux PC.(10.0.0.1 & 20.0.0.1)
still wht configuration required to establish the connection between two networks using LINUX PC.
from router(linux PC) both network PC's are pinging but not from one network to other network.
I recently ubgraded to ubuntu 9.10 from 9.04, but I had the same problem there. I can see the secure connections, but when I try to connect to them, it tries to connect, works at it for about a minute, and then asks for the password again. This just started a week ago or so. I am new with ubuntu, so while I know that there are terminal outputs I should probably post, I don't know which ones.
View 5 Replies View Related1) I connect to the internet on a wireless router from my isp.
2) I use an older router for my media server (pc) to my ps3. The router given to me from my isp is the only one I can use to connect to the internet, yet it has the worst UPnP support (ie: none).
So with this current setup, I have to disconnect from the the wired network to be able to access the internet. So how can I access the internet while still connected to the wired network?
I have a machine running Xubuntu [2.6.22-14-generic]. I have been trying to get this machine connected to wireless for ages, and I'm having another stab at it. So far I have install ndiswrapper and loaded the driver for a Linksys wireless adapter. The output of 'ndiswrapper -l' reports:
Code:
wusb11v4 : driver installed
devoce (13B1: 000B) present
So as far as my newbie knowledge goes, I believe that step to be completed, correct?When I turn on the machine is type in
Code:
sudo sh
modprobe ndiswrapper
to get the card running to where it will appear in the iwconfig dialog.The commands 'iwlist wlan0 scan' will list all the wireless networks around me, but I have been un-able to connect to any network, even unencrypted ones. I have tried to connect both through Wicd and command-line to no avail. For command-line I have used:
Code:
sudo ifconfig wlan0 down
sudo dhclient -r wlan0
sudo ifconfig wlan0 up
[code]....
With the final 'dhclient wlan0' commands, the following is returned:
Code:
There is already a pid file /var/run/dhclient.pid with pid 134519120
Internet Systems Consortium DHCP Client V3.0.5
Copyright 2004-2006 Internet Systems Consortium
[code].....
I have attempted to go ahead a step further and connect to an encrypted wireless network, however, I receive the same message, as well as another error message upon trying to enter the key, with the following code:
Code:
iwconfig wlan0 key s:"thekey"
Error for wireless request "Set Encode" (8B2A) : SET failed on device wlan0 ; Invalid argument.
I have an Atheros AR242x card. It can see my wireless network (WPA2). When i attempt to connect to the network it asks for the WPA2 passphrase. After entering the password it begins connecting but hangs up for about 3 minutes before saying wireless disconnected. The wireless worked for one day on a fresh install (Ubuntu 10.04)and then started doing this.
View 2 Replies View RelatedI have a WLAN Driver Azure Wave AW-NU222 Wireless LAN Card in my Medion computer.
After installing Ubuntu it seems to detect the wireless networks in my area. However, when I try to connect to my network, it tries for several minutes and then times out with no error message. I have set up the credentials and also tried removing the encryption (WPA-PSK) from the network itself, but it still doesn't connect.
Connect via an Ethernet cable is fine, and I know that the network is good because I can connect via my Windows Laptop and various other wireless devices.
I suspect it's due to drivers, but I'm having trouble downloading a driver which I can try and install using Ndiswrapper. The Medion website just a windows executable when I try and download the driver specific to my machine when I really need the .inf file.
Here is a situation I have never come across (though I have only been using linux since 2004).I am running ubuntu 10.04 and using Wicd Network Manager.I can connect to my WPA encrypted home network, but if I go to my coffee shop to use their unencrypted wifi - I cannot.Even using the terminal. I think it is the way the device sees the network - but I don't know how to fix it.I have a screenshot with wicd here:And one with connecting to the essid here:Afterwhich, dhclient was unable to obtain an ipaddress - just like wicd above.
My iphone connected to this network easily without encryption or needing to use the browser to authenticate, etc.Any ideas on how to fix this?Specs:Samsung NC10lspci:
Code:
02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
[code]....
I have a HP Mini1000 and recently switched over to Ubuntu. I followed the directions found here:[URL] However, I still cannot connect to wireless networks though my card seems to be scanning for them and finding them. I have tried connecting to open networks and ones that require authentication.
View 1 Replies View RelatedI have been using Ubuntu for quite a long time and I never got around fixing this particular wireless problem. I have tried Network Manager as well as Wicd. I am never able to connect to a secure network (WPA). When I use Network Manager, it just tries for a long time and gives up. As for WiCD, it again tries for a long time and finally says "Bad Password". Of course, the passkey is correct. When I connect to an unsecured network, it goes through just fine. I have a Dell Inspiron 1545 which uses a Broadcom 43xx Driver.
View 3 Replies View RelatedI've managed to install my WUSB600N on 10.10 (which was NOT easy!!) and I can see all my local wireless networks, but I can't connect - it attempts to connect then disconnects after what I guess is timing out.I know that you can place these cards in broadcast mode (I think), where you can see networks but not connect. Considering that to get this card working I had to attempt about four different sets of instructions to get this far, could I have placed the card in a broadcast mode? I've been at this for about three days, and unless I go out an buy another network card (I'm currently connected using it through windows) then I'm going to have to give up on Linux, which I really don't want to
View 9 Replies View RelatedI have an Eee PC 1015PEM with Ubuntu 10.10, I believe the wireless card is an rt3090 (though sometimes I see references to rt2860).I had problems getting this to connect to any wireless network originally but eventually was able to fix this by blacklisting a number of modules.However I am still unable to connect to hidden networks and have not been able to find a solution.
View 3 Replies View RelatedGot Ubuntu 11.4 installed on my Lenovo Thinkpad X220.Except very very rare cases i'm not able to establish awlan connection.Scanning is possible at all times, monitor mode works as well.Network Controler (lspci)
Code:
03:00.0 Network controller [0280]: Intel Corporation Centrino Advanced-N 6205 [8086:0085] (rev 34)
[code]....
So I was the one who couldn't get their ethernet port to function properly. Most likely, this was the result of bad hardware since none of the community's suggestions for software fixes did anything. I believe this is probably true.Indeed, when I bought a cheap $10 wireless USB dongle, it immediately worked better than all the previous things. It detected networks, displayed network strength and even allowed me to attempt login.
The only problem now seems to be that it cannot login. I've rechecked the password countless times, but it just shows the 'connecting to wireless' animation for a minute or two and then poops out and says, 'disconnected'.I assume if everything is getting me this far, the driver is not the problem with the device. Is this a safe assumption?
I just installed Ubontu 9.10 and I am a first time user. I am attempting to run my Sabrent usb 2.0 wireless-N ieee 802.11n device with Ubontu but I cant seem to figure it out. I can not access it as a regular usb device and I can't access the installation driver. The device loads up an installation screen when I use it on windows so I know its not the device. Not sure how to install it or to get it to run from here.
This is what I have done thus far:
lsusb -ID 148f:3070 Ralink technology
I have my main network with internet and DHCP which is on 192.168.x.x with a router.Now I have set up an Ubuntu file server and i want it on a separate home network with static ip addresses range of 10.x.x.x. and it is also connected torouter.So i will have two networks, one private static with no direct internet access, and the other with internet and DHCP. I want to know how I would "bridge" these two networks so that I could access my file server from the DHCP network. How is this typically done?
View 14 Replies View RelatedI decided to upgrade to Ubuntu 10.04 a few days ago. My internet then stopped working.I changed the security for my network to WEP (instead of WPA)Is there another way around this problem or can I just download another driver? I do not intend to stick with a WEP secured network.
View 6 Replies View RelatedI've installed it no problems on my desktop and I really love it. Now I'm trying to install it on my Satellite and I'm having a couple of problems. When trying to connect to my wireless network, I can see my network, but it will just keep asking me for my WEP. I've confirmed that there is nothing wrong with the network or the password I've provided. Sometimes when I boot up, the network manager just says that the wireless networks are disconnected and can't find any. The wired connection always works just fine.
Here are the system specs:
Toshiba Satellite M45 S169
Ubuntu 10.04 Lucid Lynx LTS Fresh Install
Ethernet controller: Atheros Communications Inc. AR2413 802.11bg NIC (rev 01)
Kernel driver in use: ath5k
Kernel Modules: ath5k