When I run OpenVPN server - tap0 adapter, it breakes Teredo(Miredo) IPv6 address down. I dont need IPv6 on OpenVPN, so is there any way to disable IPv6 on tap0 completely?
View 2 RepliesNow that IPv6 is becoming more and more common, I found the need to disable IPv6 on some interfaces but have it enabled on other. I found that /proc/sys/net/ipv6/conf/*/disable_ipv6 does exactly that. I am now wondering if anybody knows, why are networking scripts so counterintuitive. /etc/sysconfig/network has an option:
NETWORKING_IPV6=yes
All this option does is disable some ipv6 services (dhcpv6...), it does not disable IPv6 in whole (as one would assume...that's why you had to disable it with module parameters). Searching for more IP6 related config option, one can find that /etc/sysconfig/network-scripts/ifcfg-* scripts can contain:
IPV6INIT=yes
Again, this option does not disable IPv6 protocol on the interface, it just skips running ifup-ipv6/ifdown-ipv6 scripts. I added a /sbin/ifup-pre-local. Now, this script runs before ethX entries are created (other scripts run when it's already too late) in /proc directory, so it modifies default values which are then used after those entries are created:
#!/bin/bash
#
[ -f "/etc/sysconfig/network-scripts/$1" ] && . /etc/sysconfig/network-scripts/$1
[code]...
When I do ifconfig than IPv6 address is appearing on an interface. However when I run the system-config-network and select to edit same interface than it shows the normal ip4 192.168.1.x address. Why is it like that? ipv4 at one place and ipv6 at other?
View 3 Replies View RelatedI have tried to disable the ipv6 support in ubuntu 9.04 32bit but the /etc/modprobe.d/aliases does not exist so I can't disable the suport as sugested for the previews versions. I need to disable it becouse it is pounding a total maihem in my vamware machines.
View 7 Replies View RelatedI have a host and typing ifconfig I get:
eth0 Link encap:Ethernet HWaddr 00:0E:7F:4F:E4:09
inet addr:130.130.9.9 Bcast:130.130.255.255 Mask:255.255.0.0
inet6 addr: fe80::20e:7fff:fe4f:e409/64 Scope:Link
[code]...
and to do a test i want to disable or delete the ipv6 address, but mainteining the other configured parameters. Looking on the ifcfg config file I have
DEVICE=eth0
BOOTPROTO=static
BROADCAST=130.130.255.255
[code]....
and nothing about IPv6... Then, using ifdown-ipv6 could i remove only the ipv6 address?
have had a problem with my ubuntu system recently in that it will only let me connect to the Internet through Firefox if I switch network.dns.disableIPv6 on. How do I do the equivalent in Ubuntu to enable me to use Ephiphany etc which are not working anymore
View 2 Replies View RelatedI set up a static IPv6 address and a gateway in /etc/network/interfaces. However, a bad router in my network environment alway send wrong ICMP router discovery messages to me. So I have got extra (wrong) IPv6 address and gateway, and the routing is confused. On Windows Servers, I can use "netsh interface ipv6 set interface "Local Area Connection" routerdiscovery=disable" to disable ICMP router discovery. But I don't know how to disable it on Ubuntu 9.10. How could I disable ICMP router discovery for IPv6?
View 4 Replies View RelatedI have an Asterisk-server with 2 interfaces, a WAN-interface (eth1) and a LAN-interface (eth0).
SETUP : IAX-provider(internet) --> firewall --> Asterisk-server --> switch --> clients_on_LAN
So everything coming from the IAX-provider on port 4569 is forwarded to the Asterisk-server's WAN-interface (eth1). This needs then be routed to an internal SIP-phone (an IVR-system will define which one) via eth0. When a call is initiated from an internal SIP-phone (they register to the IP-address assigned to eth0) it needs to be routed via eth1 to the gateway (192.168.4.250). Asterisk will setup an IAX-channel on WAN-interface (eth1) to the IAX-provider (via gateway). So... will this work :
Code:
route add -net ip_IAXprovider netmask 255.255.255.0 gw 192.168.4.250 dev eth1
Code:
route add -net 192.168.4.0 netmask 255.255.255.0 dev eth0 (no gateway needed for the LAN-interface, communications to the gateway need to go via the WAN-interface !)
As part of my job, I have to configure a lot of network devices that are configured through web pages. This generally means plugging in to them via ethernet, going to their default IP address and reconfiguring them. I set my IP address using ifconfig, which is much faster than plugging numbers in to networkmanager's GUI. The problem is, NetworkManager seems to take the interface down at random.I could disable NetworkManager but then I don't have a wireless connection.Is there a way to tell NetworkManager to temporarily ignore what is happening on a specific interface or should I just ditch NM altogether when doing this kind of work and use wpa_supplicant to get on my wireless?My co-worker with the Windows machine is looking over my shoulder and chuckling
View 2 Replies View RelatedI have an Asterisk-server with 2 interfaces, a WAN-interface (eth1) and a LAN-interface (eth0).
SETUP :
IAX-provider(internet) --> firewall --> Asterisk-server --> switch --> clients_on_LAN
So everything coming from the IAX-provider on port 4569 is forwarded to the Asterisk-server's WAN-interface (eth1).
This needs then be routed to an internal SIP-phone (an IVR-system will define which one) via eth0.
When a call is initiated from an internal SIP-phone (they register to the IP-address assigned to eth0) it needs to be routed via eth1 to the gateway (192.168.4.250). Asterisk will setup an IAX-channel on WAN-interface (eth1) to the IAX-provider (via gateway).
So... will this work :
route add -net ip_IAXprovider netmask 255.255.255.0 gw 192.168.4.250 dev eth1
How can I force a Wine application (or Wine itself) to use a specific network interface? I have installed hamachi and am trying to play starcraft over virtual LAN. However, when I run Starcraft with hamachi running, it does not work. I have now determined that hamachi creates a network interface called "ham0". How do I force Wine/Starcraft to use the "ham0" network connection? I have looked into forcebindip but it crashes on wine.
View 1 Replies View Relatedim trying to ping from a specific interface, I have a wired and a wireless connection both going into my laptop.
My wired adaptor eth0 is on the ip 172.16.109.75 my wifi adaptor wlan0 is on the ip 192.168.1.69
when I ping google with my eth0 unplugged with the following command
Code:
conneco@mcr-pc-29334:~$ ping -I wlan0 www.google.co.uk
PING www.l.google.com (74.125.230.115) from 192.168.1.69 wlan0: 56(84) bytes of data.
64 bytes from 74.125.230.115: icmp_seq=1 ttl=51 time=32.7 ms
[Code].....
How can I force a Wine application (or Wine itself) to use a specific network interface? I have installed hamachi and am trying to play starcraft over virtual LAN. However, when I run Starcraft with hamachi running, it does not work. I have now determined that hamachi creates a network interface called "ham0". How do I force Wine/Starcraft to use the "ham0" network connection?I have looked into forcebindip but it crashes on wine .
View 5 Replies View RelatedI'm hoping some of the Linux network experts can help me with this problem.
Situation: I have a technology which is a WebLogic JEE application that communicates to an Oracle database. Everything is installed in a single Linux virtual machine running in VirtualBox. Traffic from the JEE application goes via JDBC over TCP to the local running database. What I want to do is test a new database firewall server that wants all traffic destined for the database to flow via another virtual machine running the DB Firewall software.So therefore want I need to do is have DB traffic forced out over one interface only to return on another interface on the same VM listening on a different address.
JEE application running in WebLogic bound to 192.168.111.12 (eth1 a VirtualBox hostonly interface). Makes a request for 10.0.111.12 (eth2 a VirtualBox internal interface) which the database is listening on. Because both IPs are on local interfaces, Linux is going to handle the traffic and not route the 10.x traffic via the 192.x interface.I also have running the database firewall server which has a bridge (br0) between the HostOnly network and the Internal network.Both systems are running Oracle Enterprise Linux R5U4, which is basically the same as RedHat.What I want to do is have the request for 10.0.111.12 forced out via 192.168.111.12, bridged over the br0 connection and back into 10.0.111.12 and to the database. My networking knowledge is pretty good, but i'm stuck right now on the right way to do this. I'm pretty sure it is possible, I just need clear advice.
Reason for setup: Ideally I would build the system with the database on a separate machine so that I can easily route the traffic. Unfortunately we have many VirtualBox based demonstration systems with both the application and database installed on the same VM and therefore the amount of work to migrate these two dual VMs is going to be significant, also many of these VMs are demonstrated from laptops which have limited resources and creating a new database VM reduces overall performance. If I can create a way to force the traffic in this manner off and back onto the same VM via the other VM bridge, it would be fantastic.
I have a linux router with 2 physical ISPs and a VPN tunnel that all my traffic passes through. I would like to setup a rule to redirect all traffic from one internal IP address (10.0.0.x) through the physical link only. My current script is as follows.
iptables -F
iptables -X
echo 1 > /proc/sys/net/ipv4/ip_forward
[code]....
My goal is to do something similar to the mangle on the tor traffic, but for an entire host.
11.04 64 bit I just picked up a new high-gain usb wireless adapter that I would like to use for a while in place of the built in wireless adapter in my desktop. It is detected and works just fine. My question is this: Is there any way I can disable just the built in adapter and leave the new one active (or visa versa?) I don't want to remove the built-in one as there will be occasions that I will want to use both.
View 6 Replies View RelatedI have 2 NICs on my computer connected to 2 different networks. On 1 interface i wish to disable the return of ping and on the other interface i wish to still allow ping. Is this possible? Both interfaces need to be able to send and receive data. I know that you can disable ping in /etc/sysctl.conf but is there a way to set the ping value for a specific interface only?
View 2 Replies View RelatedIs there possibility to disable ipv6 protocol for given interface? More info:
1. I have PC with 3 Ethernet cards. Two of them up(eth0, eth1), other is down(eth2).
2. eth0 is connected to LAN, so it configured to obtain IPv4 address via DHCP(works)
3. eth1 is connected directly to other Ethernet card in other PC and used by packet generator(tcpreplay utility) in debug purposes. ipv4 is not configured on this interface.
4. I have rebuilt kernel with build-in ipv6 support, because it required to work in LAN with some other PC's.
5. Now all my interfaces got own link-local ipv6 address(like fe80::xxxx:yyyy:zzzz:qqqq )
How to get rid ipv6 on my eth1 debugging-interface? Any unauthorised packet send thru interface wastes whole debugging session. "ifconfig eth1 del " doesn't helps. Can it be achieved using tools available in slackware 12.2 or at least slackware 13.1?
I used to play with gw6c ( a client for tunnel broker ) It works well with fedora9 , fedora 10, but not with leonidas. my rpm is gw6c-6.0-0.4.beta4.fc9.i386.rpm ( a little old!) when I tried to install i have got this: libcrypto.so.7 est ncessaire pou w6c-6.0-0.4.beta4.fc9.i386 I try to make a soft link to libcrypto.so.0.9.8k, but nothing; The question :-Is there a solution for that pb - did you know a better client for non native ipv6 connectivity?
View 2 Replies View RelatedI have been struggling to get FC15 to act as an IPv6 router for a while now, am sure I am missing something trivial.. The idea is that I have a ppp / adsl connection (this works fine), use the wireless card on my pc with hostapd and dhcpd to provide connections to other pcs (works fine), and radvd to delegate ipv6 addresses.
The issue seem to be that as soon as I turn on ipv6 forwarding (net.ipv6.conf.all.forwarding =1), the ppp connection no longer gets an IPv6 address. This means the router cannot ping any ipv6 address outside my network.
If I disable ipv6 routing, my router gets an IPv6 address on its ppp connection, and can ping things such as ipv6.google.com just fine, however (of course) no packets are forwarded from my network and radvd complains that forwarding is disabled.
Im new to this Cent OS as well as Unix based Operating Systems. Please help me with the below requirement.My Company is a Serach based data collector from different websites like Google, Yahoo & many more..Collecting the data from the search engines is a issue for right now.. As many search engines are blocking us to search and retrive the date after some time.. Taking Google as example : Google Blocks my IP after every 30 mins of retriving.. Application is a Windows based & using Windows 2003 as the Server.. Would like to give a Dynamic IP to the Windows Server via 1st Ethernet Card & enable the 2nd Ethernet for the Internet..Eg : eth 0 = 192.168.1.1eth 1 = x.x.x.x (Public IP)I have check with few of my friends who told me to get Linux or Cent OS installed to do a interface disable after given time & enable a secondary device or virtual interface the next couple of seconds... Like eg : eth 1 = x.x.x.1 eth 2 = x.x.x.2 eth 3 = x.x.x.3 so on.. Would like the eth 1 to be down after 60 mins & eth 2 o be up & again after 60 mins of up time eth 2 down & eth 3 up.
View 6 Replies View RelatedOkay so on WebUpd8 website, (url), I found a way to disable IPv6 and I was hoping to get a little more of an understanding of if I should or not from comments there, but unfortunately I haven't gotten enough to say let's do that. So I figured I might get a better understanding on here.
I am not very familiar with IPv6, but to my understanding its a newer thing that's rarely found currently with ISPs, but can be a security issue now.
Anyone know how to disable IPv6 but still use IPv4?
View 6 Replies View RelatedI am experiencing very slow internet speed while downloading files from internet. Although torrent (KTorrent) download speeds are okay. I am using 'rekonq' Web Browser. Konqueror is slower than this and Firefox is the slowest. Thats why I have uninstalled Firefox from my Suse 11.3 KDE. I went through the guides mentioned here:
Disable IPv6 But the images shown here in the first post (by caf4926) [URL] have slightly different configuration from my computer. (My account does not allow me to post attachments). In the pic 2, Do we have to select the option: "User Controlled with NetworkManager" before unchecking the Enable IPv6 option.
Howto disable IPV6 in Lenny?
I added this line:alias ipv6 off in /etc/modprobe.d/aliases:# cat /etc/modprobe.d/aliases
# These are the standard aliases for devices and kernel drivers.
# This file does not need to be modified.
#
# Please file a bug against module-init-tools if a package needs a entry
# in this file.
[Code]....
alias ipv6 offbut howto check after restart if ipv6 was loaded or not?
does opensuse 11.2 come with IPv6 enabled by default? where in the gnome gui can i access these settings?
Edit-i went into the gnome network manager applet and i cant find any IPv6 settings for any of my used connections-ethernet, wireless and VPN connections all seem to only IPv4. Can anyone else confirm that opensuse 11.2 uses only IPv4 on its network connections?
I just finished setting up my slack machine as a home server (printers & files) and I noticed that I have an IPv6 address (from ifconfig)... I didn't know I did. I used to work in tech support and when a windows or OSx machine didn't connect properly on a LAN, disabling IPV6 was a common troubleshooting step. Is there a way to easily turn inet6 connectivity off/on in Slackware? (I want to keep the ability to get an IPv6, we will all use those in the future)
View 2 Replies View RelatedI have installed bind with yum install bind bind-chroot.I am having query timeouts due to no ipv6 connectivity.Is there a way to re-compile and not loose the chroot structure?Or is there another way to disable ipv6 lookups?Example of issue resulting in ipv4 query timeout:
30-Dec-2010 17:52:03.226 client x.x.x.x#53593: view internal: query: paypal.com.cms.local IN A +
30-Dec-2010 17:52:03.227 client x.x.x.x#53594: view internal: query: paypal.com.cms.local IN AAAA +
30-Dec-2010 17:52:03.228 client x.x.x.x#53595: view internal: query: paypal.com IN A +
[code]....
My laptop was working fine on wireless till the userinterface changed and it defaulted to ethernet and now it won't let me go back on wireless How do i disable ethernet?
View 4 Replies View RelatedWhen I go out of town I normally take my Acer Netbook to travel light. I ran into a problem over the weekend which I have seen before and couldn't find the cause. I used the wifi at the house I was staying at and could connect to the router via Wicd and ping outside IP addresses, however, I could not connect to any websites with Iceweasel or Midori. I receive the generic error that the browser is unable to connect. Now that I am back at my house I cannot repeat the problem, but have found a couple threads about disabling ipv6 protocol. The symptoms sound like a browser setting, but I couldn't find any settings that looked unusual.
View 2 Replies View Related