Ubuntu Networking :: Atheros AR5001 Only Works If In Same Room As Router?
Mar 2, 2011
A Toshiba 35MX-S114 laptop with Atheros AR5001 works but unless the laptop is in the same room as the router I am not able to connect.
After a relative gave me their old laptop, I installed 10.04 Lucid but I am having problems with the Atheros AR5001 based wifi. I've been able to update the OS using wifi with the laptop in the same room as the router. If I move about 9 metres away from the router into another room, with applet showing 3/4 blue bars and effectively still within line of sight of the router, I lose the connection. Wifi receive is working so well that the Network Manager Applet detects several of my neighbours' routers but not well enough for me to connect to our router.
Originally on the Toshiba laptop under XP there's supposed to be a hotkey Fn+F8 which enables/disables the wifi antenna, in contrast Fn+F9 does disable the touchpad as stated in the manual.
My router is recognised but I cannot connect. Is it a driver issue?
View 1 Replies
ADVERTISEMENT
Dec 30, 2010
I got a used computer (Toshiba Satellite A215-S5829) for Christmas, and it was running Vista *shudder* so I decided to wipe the hard drive, and install the latest Ubuntu. This is my first real foray into linux, and I've loved the system, but the only problem I've had with is so far is I can't get the wireless to work. I believe the card it has is Atheros AR5001, and I've tried installing the "madwifi" drivers, but I can't get them to register. I've been following the suggestions of dozens of different forum posts and answers I've found scattered around the internet, but I haven't been able to get anything to work correctly.
When I view the "Additional Drivers" in System > Administration, it says "Alternate Atheros "madwifi" driver: This driver is activated but in use," but when I click on the internet icon in the top panel, it only gives me the wired connection. It used to also give me the wireless option, just without ever successfully finding any wireless networks to which it could connect. Like I said, I've done about a half-dozen different things without any success.
View 3 Replies
View Related
Jan 12, 2010
I've got a little netbook, and all works fine, except for one small thing. I'm able to connect to a wireless network with my Atheros AR5001 just fine. However, if I right click on the network icon, and disable network or wireless and enable it again, wireless won't work anymore. I can't see and connect to any network at all. Except when using airodump-ng from the famous aircrack-ng tool set. When using airodump I'm able to see any network and their specs just fine. I don't even have to be in monitor mode to do airodump-ng (the wireless must be off in the network manager though). Is there any way of getting my wireless back when I turn it on again?
View 9 Replies
View Related
Jan 16, 2011
I'm just having a bit of trouble with activating my wireless card (see title for details). rfkill - I installed it but nothing was soft / hard blocked (whatever they mean). I did the rfkill unblock command anyway but it didn't appear to change anything Tried doing it manually through system-config-network but this yielded no luck either. Basically all it does is continually ask for my WEP key, even though I've typed it in correctly a million times. why I don't have WPA2 because I do not have the ability to change it
View 1 Replies
View Related
Aug 10, 2010
I have recently installed Ubuntu 10.04, and today the wireless connection has started to become spotty. The networks menu shows no wireless entries when they were there the day before. Again I have the Atheros AR5001 wireless card, my network is WPA2 and is 802.11g
View 1 Replies
View Related
Jul 31, 2011
I've been having problems with the Atheros AR5001 wireless card in my EEE PC. Whenever I'm connected to an encrypted network of any description (WPA2 at home, WPA-PSK at work), the connection will drop out after some time, ask for the key again, then will drop out after a shorter time. This repeats until it's continuously asking for the key. This is no problem with an unencrypted connection. I've installed the madwifi module as per the instructions in this thread, but that doesn't seem to have helped.Ubuntu 10.04.3 LTS, 2.6.32-33-generic i686 kernel.
lspci:
Code:
01:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
ifconfig:
Code:
wlan0 Link encap:Ethernet HWaddr 00:25:d3:12:c3:37
inet addr:192.168.2.4 Bcast:192.168.2.255 Mask:255.255.255.0
inet6 addr: fe80::225:d3ff:fe12:c337/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
[code]....
View 9 Replies
View Related
Dec 31, 2010
F13 on a EEEPC 1000HD.I have big problems with my wireless card. lspci says:
Code:
01.00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01)
I can't use Network Manager (it continue to ask me for the WPA password9. So I stopped it and I use command line, following this: [URL]
From the log I can see that it tried to associate to AP and after a lot of tries: it connects BUT the connection is really SLOW and UNSTABLE! (pinging hosts on the same network gives me about 50% packets loss) I am worried about this entry in the log:
Code:
ath5k phy0: unsupported jumbo
I am going to try to install madwifi, but before that I'd like to have your opinion and listen your experience! I see a lot on infos about ath5k, but I'd like to be pointed to the right direction!
View 6 Replies
View Related
Apr 27, 2010
I am currently attending college and living in the dorms we have 3 either-net ports and 3 people in one room. So we bought a router so we could have more then three things plugged in. I figured out via wikis how to set it up to run as a switch but I would like to run it as my own subnet. I have search far and wide for a guide or explanation on how to do this but the only one that seemed to be what I wanted was a bit beyond me.
Code:
Picture of how we get internet
internet comes in through wall from schools router(s)
| ___
====|=======|___|==several pcs plugged into router
[code]....
View 1 Replies
View Related
Jun 17, 2011
I have Ubuntu 10.10 on a Toshiba satellite L300 with an Atheros AR5001 wireless network card. I can get the computer to see the network but it wont persist, it keeps going offline or asking to be re connected.Also Firefox will not find the internet even if the wireless icon shows the wireless network is alive.I can use the laptop for the internet if I plug in the LAN cable but have no luck with the wireless. Security for the modem is using WPA&WPA2 and it will connect according to the icon in the title bar for the wireless network.
I have tried the Atheros site for a driver but had no luck finding one. Not even sure if that is what I need to do.
[Code]...
View 2 Replies
View Related
Aug 12, 2010
I have a Acer Revo R3610 nettop on which I installed oS11.3. It has an Atheros AR5001 wireless network adaptor.I'm getting very bad latency and throughput on with this card. In comparison my Thinkpad with Intel card achieves at least 10 times the throughput from the same location. Also when I boot my wifi will come up authenticate and then a few seconds later disconnect and reconnect. I've tried updating the kernel to 2.6.35 as one of the fixes was to improve the performance of the ath5k driver. I'm using wpa2 authentication.
Here are some details:
Code:
mediacentre:~ # /sbin/lspci -nnk
00:00.0 Host bridge [0600]: nVidia Corporation MCP79 Host Bridge [10de:0a82] (rev b1)
Subsystem: Acer Incorporated [ALI] Device [1025:0222]
[code]....
Is there anything else I paste that will help determine the cause of the bad throughput. Browsing the web or copying files across the network is bordering unusable.
View 9 Replies
View Related
Apr 16, 2010
I have a brand new ASUS EEE PC 900HA with Ubuntu 9.10 installed on it. The wireless hasn't worked yet but the ethernet is fine. I've been browsing the forums for hours to find a fix but now I've installed/queried/removed so many things I'm totally confused.
lspci -v gives me this
Code:
01:00.0 Ethernet controller: Attansic Technology Corp. Atheros AR8121/AR8113/AR8114 PCI-E Ethernet Controller (rev b0)
Subsystem: ASUSTeK Computer Inc. Device 8324
Flags: bus master, fast devsel, latency 0, IRQ 27
[code]....
View 9 Replies
View Related
Feb 5, 2010
I have an HP dv2000t laptop running 9.10 with an Intel PRO/Wireless 3945ABG wireless adapter. I have no problems connecting to my wireless network when I'm within about 15 feet of the router. When I move to a different room, my network shows up the list of available ones, but I usually can't connect. When I run Windows, I have no problem connecting from the same distance. I'm using the default network manager.
View 1 Replies
View Related
Jan 22, 2010
I just bought a TRENDNET TDM C4000 (=modem/ wiredrouter) and got it working. If I connect my computer with through the ethernet port directly, the internet will work. However, when I try connecting the ends of the ethernet cable on the modem and my wireless router, it's not transmitting. I know I set up the wireless router correctly because it worked with my previous modem. I just need to know how to configure my modem so that it works with my wireless router (D-Link DI-524).
I have a long wired ethernet wire to satisfy my academic needs for the internet at the moment but my mother is not able to surf the internet and it would be more convenient for myself to put the wire back to my desktop and have my laptop browsing wirelessly.
View 1 Replies
View Related
Jul 27, 2010
I recently bought a new wireless router (Cisco E1000) to use in my house. The E1000 supports mixed-mode 802.11n/g/b, which is what I have enabled. It is the first 802.11n router I've had. My netbook (an HP/Compaq Mini 110) only supports b/g. When connected to this new router, I can only see my status as root. NetworkManager shows a little red exclamation point, and 'iwconfig' shows nothing. It's missing in the 'iwlist scanning' list. Even still, I'm connected and can do everything just fine. However, everything shows up fine when I run 'sudo iwconfig' or 'sudo iwlist scanning'. These have always worked as a standard user before.
View 1 Replies
View Related
Aug 6, 2010
I have Fedora 13 installed on my Fujitsu Siemens Laptop. I can only connect to my wireless router when the laptop is close to it. When I try using the laptop in the next room, it keeps asking for the password and eventually disconnects after 3 or 4 attempts. The wireless connection worked fine in Windows XP.
View 2 Replies
View Related
Jun 29, 2011
I need to change my network key number in my router, because I think it is beening used by a near neighbour in the apartment above, can anyone tell me how to do this.
View 3 Replies
View Related
May 12, 2011
The problem is wireless connections show up in the connections list but when I try to connect it will just keep trying to connect and will never actually complete. During the connecting process it will constantly ask for my WPA2 key. Wired connection does work but that is only a temporary fix to this problem. The phy0 wlan hard block is stuck to yes also, so that could be the problem.other info:Running Ubuntu 11.04 dual boot with windows vista 32 bitWireless card is Atheros ar5001 on Toshiba satellite laptop
View 5 Replies
View Related
Jul 28, 2010
I'm trying to do a SSH connection between my home and work PC both machines are running ubuntu 10.04. I have read all the comunity documentation at [URL] from Work PC. I went on to the web site what is my ip address and noted down the number, From Home i opened a terminal and typed: pnig (ip address). to which their was no reply, now i'm assuming i need to configure the works router to except connection requests, is this Correct?
Also what information do i need from my works network and how do i get it? I understand that I need the routers expernal ip address, but how do i referiance a specified computer after that address? What program do i use in ubunu and how is that information applied to it?
View 4 Replies
View Related
May 13, 2009
the only error message I can find comes from "dmesg|tail"all it shows is
"no IPv6 router"any body know what is going on here or where where to look for more clues the next time I get around public wifi Oh the windoze washers and apple polishers don't seem to have any problems at all
View 4 Replies
View Related
Jun 29, 2010
No wireless networks detected with AR5001 chipset
View 1 Replies
View Related
Jul 22, 2011
I have TWO L3 + router switch (say switch1 and switch2). I created VLAN100 with VLAN ID 100 in both the switches. I created router 192.168.1.1/24 in Switch1. I created router 192.168.2.1/24 in Switch2. Switch1 is connected with 1.x/24 PCs. PCs are configured with 1.1 gateway. Switch2 is connected with 2.x/24 PCs. PCs are configured with 2.1 gateway. Both Switch1 and switch2 are connected by a trunk to carry VLAN100 data.
1)I have few PCs of 1.x connected to say Switch1 Is it possible for PC with IP 192.168.1.100(x) to ping PC with IP 192.168.2.100(y)?What are the configuration required in both switches to make them communicate ? All the device in both the subnets should ping/communicate with each other.
2)Move PC (192.168.1.100) to switch2. Move PC (192.168.2.100)to switch1.What will happen when PC(1.100) ping (2.100) and vice versa?What will happen when PC(say 1.80 in switch1) pings PC (say 1.100 in switch2) and vice versa? What will happen when PC(say 1.80 in switch1) pings PC (say 2.100 in switch1) and vice versa?
View 2 Replies
View Related
Jul 11, 2011
I installed 11.04 some time ago. I got my printer to work, but I have tried to use wireless and I cant. I can perfectly connect using a wired connection but on the network menu in the taskbar it tells me that wireless is turned off by hardware switch. I am suspecting that I don't have the drivers for my atheros wireless card, but when I click on additional driers it tells me that there are no drivers to download. how to configure my wireless card to work with natty?
View 9 Replies
View Related
May 22, 2010
I`ve read solution in this thread. [URL] It seems Linux driver for AR5001 does`n support ad-hoc mode. But user Selak found solution with a bridge. With this advice by my AR5001 card can finally be detected by other devices. I can connect to it with my girlfriend`s net-book with XP, but I still can`t share internet. May be I miss something. I haven`t shared wifi before.
[Code]...
View 1 Replies
View Related
Jun 25, 2011
Wife's laptop has AR5001 Wireless Adapter laptop model is Toshiba Satellite A215
Problem : Wireless networking randomly loses connectivity and can not regain connectivity, the only apparent solution is a full power down , this is not even certain to work. The card works under Windows, she hates Windows. (I love her for this) I know it's not faulty hardware , because it will work for days on end under Windows without problems.
Things I've tried : madwifi drivers (any and all versions available) : These increase stability of the signal and seem to delay the inevitable however it still happens. When using these drivers the only option is to unload them modprobe -r then reboot then remove them again and re add them. It makes no sense why this works, and if I don't remove them prior to rebooting it will not work.
ATH5K drivers : These are pretty much junk, results are unpredictable at best, sometimes it will work perfectly for a few hours, sometimes it will not work at all. Nothing is repeatable, I can't seem to force whatever condition is causing this. rfkill does not show the wifi being blocked (hard or soft), unblocking it anyway does nothing, only way to make this work and it's iffy is to fully power down wait 5-10 minutes turn it back on and it MAY decide to work.
Firmware update : Updated the Toshiba BIOS to the latest version of the firmware 2.0 no joy here either. Same issue both sets of drivers.
Tried different distros and kernels : I've tried Mint 9, 10 ,11 ; Ubuntu 10.10, 10.04 , 9.10 and 11.04 (which is currently installed) , Fedora and OpenSUSE. All are giving the same problems. I have also tried a slew of different kernels no joy from any of them (I'm not at the computer with the issue now I will post exactly what kernel versions I've used when I have access to the machine).
Another useful bit of information, the hard switch to disable/enable wifi WILL disable it but turning it back on does absolutely nothing. The hotkey does nothing at all. The bios does not have an option to disable or enable the wireless card.
I will also post the typical lsmod , lspci , iwconfig all that good stuff when I get back to the computer in question. I'm probably just going to buy a PC card for it and give up on that one, but this is driving me insane and I would really like to see it resolved even if I do replace the hardware.
View 3 Replies
View Related
Aug 30, 2010
I am severe wireless problems with Ubuntu 10.04 on my laptop.(Spec below)
I have just performed the first clean install since new. Installed a new Hard Drive as well. The machine and wifi was fine under Ubuntu 9.04.
It is booting much faster now but the wifi keeps dropping off.
Spec:
Machine - Acer Aspire 4310
Wireless card - *-network
description: Wireless interface
product: AR5001 Wireless Network Adapter
vendor: Atheros Communications Inc.
[Code].....
View 2 Replies
View Related
Apr 13, 2010
Because of the configuration of my house, I need two routers.I have a DLink ADSL router as my main router and the Belkin N1 as my repeater.I have set up the IP address in the Belkin to be 10.1.1.10 - my DLink is 10.1.1.1. I have disable the dhcp in the Belkin and set the DNS as ISP provided. [URL]..I have set the channel to 11 and in the Ubuntu Network Manger I have set the IPV4 to Link Local Only. I can see the Belkin and connect with my PC.but it will not take me through to the internet.
View 9 Replies
View Related
Jun 18, 2011
I want to set up a Linux box as a wireless router to replace our existing Netgear WNR1000 router, as I believe the Netgear does not support the coming IPv6 protocol. Unfortunately, it is not flashable with OpenWRT or DD-WRT presently.
As we have Comcast, our cable modem acts as a dumb modem according to the customer support guy I talked to, and our router is the one that asks for the IP address from DHCP. Thus, when Comcast switches over to IPv6, I don't believe my existing router would work, correct?
My idea is to take a Linux box and put two NICs and a wireless adapter in it, using IPCop or Smoothwall to set up a router. I could then enable IPv6 support for when we have IPv6 with Comcast. Is that possible? Would there be a way to get BIND to hand out private IP addresses in the same subnet on the both the LAN NIC and the wireless card?
View 1 Replies
View Related
Nov 6, 2009
I have a desktop PC running Ubuntu 9.10 and Windows 7, and a Eee PC 701 laptop running EasyPeasy Ubuntu 9.04. I'd like to connect the desktop to the laptop with a wired connection (eth0), then the laptop to my ADSL router using wireless (ath0).
I have a crossover ethernet cable (I bought on ebay). I have set up my laptop with a static IP address on my LAN and it uses OpenDNS.
I have added this to /etc/sysctl.conf on the laptop:
net.ipv4.ip_forward=1
Then I tried this on the laptop:
sudo iptables --table nat --append POSTROUTING --out-interface ath0 -j MASQUERADE
sudo iptables --append FORWARD --in-interface eth0 -j ACCEPT
This is a variation on what I found on other sites describing how to set up a router. I don't understand iptables very well, but I gather that the above two lines should set up forwarding so that traffic from my router to the laptop will be forwarded to the desktop, and vice versa.
But this doesn't work. The connection doesn't even establish between the laptop and the desktop.
View 12 Replies
View Related
Apr 24, 2010
I'm having trouble getting my network set up the way that I want it/had it. You see, when I first set up my network, I just had my cable modem going directly to my standard wired router (A D-Link DI-604), which had DHCP,and was connected to all of the computers on my network. I had one switch hooked up to one of the ports of the router, but this was a regular switch, and it would not try to assign IP addresses, it would just pass through the DHCP info as I wanted.
Now however, my network setup has changed. My room mate and I both got laptops, and we decided that we wanted to have wireless access so we didn't have to constantly plug in to the router.
Now my network is set up like this: The modem is hooked up to the router(DI-604), which is hooked up on the LAN side to our computers, our switch (which is hooked up to 3 more computers), and to a wireless router card (A Gigabyte GN-BC01).
The wireless router card has two jacks for ethernet. One for WAN, and one for LAN. The LAN side we have plugged only into the computer in which the card is installed.
Now the problem is this: The wireless router card comes with DHCP by default, and it's assigning addresses to the laptops and to the computer hat it's in, and worse, the IP addresses are on a different subnet than that of the main dlink router. The Main (dlink) router assigns addresses from 192.168.0.1 (itself) to 192.168.0.254, while the wireless router card assigns addresses from 192.168.1.1 to 192.168.1.254 (itself).
Because of this, I cannot access services on the wireless network from my wired network or vice versa. The first thing I tried was setting the card to assign addresses from 192.168.0.12 to 192.168.0.253, however it just said "internal error" when I tried to do this. I decided that this may be because it sees that it was being assigned an address on it's WAN side on the same subnet. So the next thing I tried was disabling DHCP and setting the "LAN IP Address" to 192.168.0.12, hoping that the DHCP would just go through the card, like a switch. I would have set the LAN IP address to be assigned by DHCP, but this was not an option, so I decided that'd be the best thing to set it to.
Once again however, setting the LAN ip address to an address on the same subnet as that of the IP assigned to it's WAN side caused it to report an "internal error". I verified that this was the issue by setting the LAN address to several other private IP addresses to test (I.E. 10.0.0.1, 192.168.3.1, 192.168.5.12).
My question then really is: How do I set up both routers so that I can access services and computers from each network from the other network. Should I set them with different subnets and set the gateway on the wireless network to the main router? To the wireless router card? Should I put them on the same subnet? Will it know how to communicate?
Here is a link to (picture) my network diagram. Network Diagram
View 2 Replies
View Related
Mar 26, 2009
These r IP provided by my ISP that i've put on Fedora 8:
WAN IP:xxx.xxx.xxx.17 (eth0)
Subnet:255.255.255.252
Gateway:xxx.xxx.xxx.18
Valid static(public) IP set of 2:
IP:xxx.xxx.xxx.147 & 148 (eth1, eth2)
Subnet:255.255.255.240
i want to run xxx.xxx.xxx.147 as a web server & xxx.xxx.xxx.148 as a ftp server. but I'm able to ping only xxx.xxx.xxx.17(WAN IP) from outside world. Can any1 tell me that how can i bring my 147 & 148 IP online without router.
View 6 Replies
View Related
