Ubuntu Installation :: Upgrade Broke Web Browsers?
Apr 10, 2010
I upgraded to 9.1 and now my web browsers are not working properly--FireFox would not connect to certain sites, others worked fine. I installed Chrome and it worked for a short period--now none of my browsers work at all and package install manager does not work. Overall performance is much slower than before upgrade--boot time is about 4 times slower. I'd like to fix this build because I had it tweaked just the way I liked it before the upgrade--it was working great and now I'm sorry I upgraded there any hope or should I just start with a fresh install of 9.1 or even the previous version
View 2 Replies
ADVERTISEMENT
Feb 7, 2010
I upgraded yesterday ubuntu 9.10 to 2.6.31-19 kernel. After reboot, I get stack to GRUB black screen. No possibilities.
My set-up is triple boot 9.04, 9.10 and winxp. The MBR is handled by win boot.ini with no problems. Each ubuntu partition has a grub installed in it.
9.04 is on sda5 with grub installed on it ext3
9.10 is on sda9 with grub2 installed on it ext4
I am able to boot into sda9, via grub of sda5 obviously passing the correct kernel parameters and UUID.
View 3 Replies
View Related
Mar 17, 2010
I just did the latest upgrade in 9.10 via the update manager and it required a reboot. When I rebooted Ubuntu failed to load. In recovery mode it fails saying that it can't find my root device and has some suggestions about what might be wrong. I looked at the file it listed in /proc/something and the devices available by uuid in /dev/ and what's listed in /proc/something isn't in dev. I haven't made any changes yet for fear of causing worse damage. The shell it bumps to is ASH and it doesn't look to have much editor support to make changes to the proc file(ECHO > ?). Is there a safer way to get my system back online?
I'm running 9.10 AMD64 on a Dell Inspiron laptop with a dual boot to Windows 7 (For browser testing web apps/sites)
View 9 Replies
View Related
May 13, 2010
Since my distribution upgrade to 10.04 my VirtualBox guest of XP SP3 will not boot, it bluescreens and reboots. I can boot the guest in last known good config and in safe mode but I have no CDROM. I attempted a tools install over the lan but that resulted in the same blue screen. Tried installing the virtualbox-3.2 beta package and guest tools and had the same results..
View 1 Replies
View Related
Jun 23, 2010
I had a working workstation with Karmic. Then I decided to upgrade to Lucid. Bad move, it turns out.First the upgrade crashed. Just stopped doing something for hours on end, and I eventually had to reboot. After that, I had to apply lots of apt-get and dpkg love to get the machine to book. Now, I *think* I have a Lucid system, at last. Only that it doesn't work where the Karmic system used to...Our setup uses kerberos and autofs. To begin with, the upgrade lost my /etc/krb5.keytab (making it impossible to log in), but that can be easily replaced.Now, I can log in, but my home directory doesn't get mounted. In /var/log/auth.log, I get this:
Code:
Jun 23 11:13:58 pc13477 gdm-session-worker[1801]: pam_krb5(gdm:auth): pam_sm_authenticate: entry (0x0)
Jun 23 11:13:58 pc13477 gdm-session-worker[1801]: pam_krb5(gdm:auth): (user hans) attempting authentication
[code]....
View 1 Replies
View Related
Oct 11, 2010
So after I upgraded to 10.10 some of my compiz plugins stopped working. Atlantis and anaglyph give me an error like this when I enable them in CCSM (I ran compiz from a terminal to see the output):
Code:
compiz (atlantis) - Error: InitObject failed
compiz (core) - Error: Couldn't activate plugin 'atlantis'
View 1 Replies
View Related
Mar 4, 2011
I ran a system upgrade today and it froze at "unpacking replacement libpango1-common". It just wouldn't go on. The upgrade kept on showing "unpacking replacement ..", the process used zero CPU time, so I killed it, removed the lock and after Synaptic asked me to, I ran sudo dpkg --configure -a. Now I can't install anything. Everytime I try to, I get an error telling me I should run "sudo apt-get -f install", however, whenever I do that, another endless installation of libpango1.0-common starts. I tried various things like installing that package manually, removing it and so on, but nothing helped. Any advice on how to get my package installation system working again is warmly welcome.
View 2 Replies
View Related
May 2, 2010
Upon upgrading from Karmic to Lucid, Everything comes up, seemingly fine. Once logged in to the OS, my three monitors show the desktop wallpaper as well as all the icons on the desktop. A few programs that I have set to autostart do so.
However for some reason, I can only access one of the three monitors. (And not the one with the gnome-panel.) As soon as I drag my mouse from my third monitor onto the one next to it, I loose complete control of it, and it starts dancing all over the place. If I try to drag a window from one screen to the next (using Alt-Left CLick + drag and not moving the mouse onto the other monitor), the the app goes from one side of the working monitor to the other side (like it's wrapping around). Though I can see it on the other monitor for a little bit until I get it far enough for it to wrap.
Here is my xorg.conf:
Code:
Section "Files"
FontPath "/usr/share/fonts/X11/misc"
FontPath "/usr/share/fonts/X11/100dpi/:unscaled"
FontPath "/usr/share/fonts/X11/75dpi/:unscaled"
[code]....
View 4 Replies
View Related
May 25, 2010
I had the Adobe flash plugin working under 09.10 in Firefox; now after the upgrade to 10.04, it doesn't work.When I go to a web page with flash video, I get the message "Some plugins are not installed" and video will not display. I click on the button to install the plugins and select Adobe Flash. I get the message "Package is already installed." I go back to the web page and the same thing happens again.In Ubuntu Software Center I see that package restricted-extras is installed.
I tried going through Tools / Add-ons in Firefox, but the list of add-ons wouldn't load at all that way.I also tried going to Adobe's web site, but for versions of Ubuntu 09 and later it offers an "APT" file instead of a .deb. Firefox asks what application to use to open an "APT" file and I don't know what to tell it... I'd be fine downloading a .deb or using apt-get or Ubuntu Software Center though.
View 5 Replies
View Related
Aug 18, 2010
I beleive I had version 9.x installed. I upgraded once and everything was fine. I went the upgrade manager again and it found some more upgrades. The upgrade messed with grub. It then told me there were no new upgrades. Then I rebooted and it says
Try (hd0,0): NTFS5
Then the screen clears and there is some text I can't read and then it says command not found. Then it reboots.
Is there a way to fix this?
If not is there a way to recover the files from the disk image file.
View 1 Replies
View Related
Oct 17, 2010
i wanted to upgrade my ubuntu system to meerkat beta via update manager like i upgraded it the last 5+ times.
a bug showed up that i can recall from updating files previously: some software installtions via update manager triggered the programm nicotine+ (i think is was something like man-lib or man-db that, when called by the installtion programm, would trigger nicotine too). since i can close that nicotine+-window and the installation process isnt bothered any further i didnt mind.
now with this upgrade, i had to close nicotine+ around 5 times since it got triggered together with some of the files that got updated/installed in this upgrade.
and then what happened: GError something about an "unrecognized image file", it concerned a py file that was named "nicotine"...
so i waited for 10 mins and figured out that the update process had stopped. i couldnt resist and logged out, wanting to delete nicotine from my system and to reinitialize the upgrade. well, nothing works since then, grub only lets me choose different kernels which didnt help much as there was no way to startx.
my question is:
how can i reset this upgrade mess or bring this pending upgrade to an end? can i do an upgrade via network, based on the emergency shell that comes up in some kernel-recoverymodes? or should i burn a livecd, boot it and then do what? repair? try another upgrade? delete nicotine?
having 'consumed' ubuntu for years now i still wouldnt know what else to do then posting here.
View 1 Replies
View Related
Nov 7, 2010
I upgraded my ubuntu installation from 10.04 to 10.10, now surround sound (5.1) does not work in xbmc, or in another player such as vlc. Only the front two speakers work. I noticed pulseaudio and alsa are installed. I thought i removed pulseaudio once before but cant really remember. In the sound configuration preferences thing (prefs >> sound), i have hdmi output selected (hdmi goes from the HTPC to the amplifier). It only plays audio in 2.0 instead of 5.1. I tried selecting the analog 5.1 sound option, but none of the test sounds work. However i noticed vlc still played movies with audio, but only stero no 5.1.
Previous to the upgrade, i had 5.1 working fine in xbmc, never bothered to check vlc since it was all good. Also, when i go into alsamixer, it does not show any rear speakers, it just shows a front speaker and a bunch of other stuff, like headphones. I'm not sure what other output you guys need, but let me know and i'll get it. Here is the alsa-info.sh output for my HTPC: [Code]..... Another note, after i reinstalled pulseaudio the first time, vlc fails to display a 5.1 movie and still plays tero output.
View 2 Replies
View Related
Jun 21, 2010
Ever since I upgraded, the touchscreen on my Fujitsu Lifebook P1610 no longer works. On Karmic, it worked out of the box without installing any extra packages.
I see xserver-xorg-input-fpit in Synaptic Package Manager but it conflicts with netbook remix packages for some reason so I haven't tried installing it.
I didn't see anything in dmesg about the touchscreen but there are Xorg errors:
Code:
...
(II) config/udev: Adding input device Serial Wacom Tablet (/dev/ttyS0)
(**) Serial Wacom Tablet: Applying InputClass "Wacom serial class"
(II) LoadModule: "wacom"
(II) Loading /usr/lib/xorg/modules/input/wacom_drv.so
(II) Module wacom: vendor="X.Org Foundation"
[Code]....
I'm not sure if it's supposed to be recognized as a wacom tablet or what, and I'm also not sure how it used to be configured when it worked in Karmic.
View 6 Replies
View Related
Jul 4, 2010
I recently updated the kernel to the newest version(2.6.32-23-generic) using the update manager and now I am unable to boot in to my Lucid installation.
My setup is LVM on top of a RAID 0 array. My computer had been running in this configuration since Lucid was released.
The Error Code I get on Boot is to the effect of: /dev/mapper/ubuntu-os is not available.. and then I get kicked in to Busy Box.
Once in Busy Box if I try to use mdadm to mount the RAID array I get this error:
If I boot in to the live CD I can mount all of the partitions and LVM volumes, so it does not appear to be a failed drive or volume.
I have looked in the mdadm.conf, lvm config and grub config files and searched the "Google" for an answer with no-avail...
Ultimately I would like to find a solution which doesn't involve a re-installation.
View 6 Replies
View Related
Feb 19, 2010
I have two computers running Ubuntu Gnome with Firefox. Upgrades yesterday (18 February 2010) at about 1430 MDT hours (UTC 2130 hours) broke Firefox on both machines. Firefox is present in the menu, and in /usr/bin/firefox, but it will not launch, not even from the command line. I have tried "sudo apt-get remove firefox" followed by "sudo apt-get install firefox" but the problem persists. When attempting to launch firefox, it does give me a tiny brown spot at the upper-left side of the screen. This can be expanded by dragging so that it is a full screen, labeled "Firefox" but there is no content in the screen...only blank space.
View 2 Replies
View Related
Jun 21, 2011
I updated the firefox-next PPA and updated to the new release however, upon doing that, I lost the sound in ALL my browsers. (?) I am using Google Chrome and Chromium as well.I have since downgraded and the problem still occurs.
Edit: I have sound in Umplayer and SMplayer but that's it. Banshee and Guayadeque are silent...
View 7 Replies
View Related
May 17, 2011
I have upgraded from 10.10 to 11.04. I have been using wmii as window manager under ubuntu for years. After the upgrade it's entirely broken.
The metakey is not working anymore, I cannot do anything. The key itself works fine in other environments so is's no hardware issue. After several attempts I completely uninstalled wmii, removed all relevant folders in home and /etc/X11 and reinstalled wmii from the ubuntu repositories.
This fresh install does not work. It starts a strange looking wmii without any key responding to my actions. I copied my old wmiirc to ~/.wmii. When i log in I see my individualized wmii but the metakey is not working and i cannot do anything, like opening a shell.
Edit: A change to "MODKEY=ALT" in wmiirc does not change anything.
View 4 Replies
View Related
May 19, 2011
I just upgraded to 11.04 with a fresh install on a Dell Inspiron E1405. Got everything else working, but can't get my BBTether to work again.
Message says it usually means the BB is not responding. But it is also happening with Virgin Mobil Broadband stick. Both are USB connections. USB flash drive seems to work.
BBTether OUTPUT
Will run bbtether with args: ['verizon']
Starting Modem thread
--------------------------------
BBTether 0.3m
Thibaut Colar - 2009
[Code]....
View 3 Replies
View Related
May 1, 2010
Just upgraded to Karmic using the update manger. After the update, sound is no longer working. When I go to system>preferences>sounds and go to the Hardware tab it says there are no devices to configure.
View 5 Replies
View Related
May 11, 2011
So after my Natty upgrade, mpd stopped working. All I can see in the logs are the following lines:
No protocol specifiedxcb_connection_has_error() returned true The Pulse Audio wiki suggests that this might be an access rights problem: [URL]...hts_are_broken I tried that, but with no success.
Anyone else had this problem? And any ideas about how I can diagnose and fix this?
View 1 Replies
View Related
Jan 13, 2010
I'm running Ultimate Edition 2.4 on an Acer Aspire 3500 lappy, yesterday I allowed my system to upgrade the kernel (from 9.10 kernel 2.6.31-17 to 2.6.31-18 generic) as per usual but when it rebooted I had no WiFi. The network manager didn't even have a wireless section, only wired, and I couldn't setup a wireless network either. If I reboot into the earlier 2.6.31-17 kernel everything is OK.
Another problem is that even tho I have no screensaver enabled and no power saving options enabled, (ie screen never disabled) after a short time of no use the screen goes blank. If within a few minutes I touch the pad or hit a key the screen returns but if it's been an hour or so nothing I do will wake it up,even tho there is still disk activity etc, and the only way to recover is with a hard reset, hold power key to reboot.
View 4 Replies
View Related
Jun 4, 2011
I just upgraded from Fedora 14 to 15. First thing that I want to say is, "Wow, this looks great." It's such an innovative, slick, modern interface. I'm very impressed. The Gnome developers did a very good job on Gnome 3 and Fedora folks did a great job with the integration into the latest Fedora distribution. I did run into a problem, though. I'm still a little bit green in the Linux world, so please bear with me. When I upgraded with preupgrade, yum came back with repository errors. I think that the problem stems from the fact that I installed firefox4 in Fedora 14 according to the instructions on the fedoraproject.org wiki [URL]. Now I have two copies of Firefox 4 installed (after the upgrade) and I'm unable to remove the extra one (yum remove firefox4 gives bupkis ). What's worse, yum doesn't work for anything else, either . I tried a "yum clean all" but that didn't fix it. I think that I need to remove the firefox4 instance of Firefox, and then remove the repository from my repo list (I think), but I'm not sure how to do that.
View 4 Replies
View Related
Jan 15, 2010
Upgrading from 9.04 -> 9.10 broke my ability to scan using iscan.
Scanner:Epson NX100 (all in one connected via usb)
Arch:386
iscan:2.23.0-3.ltdl7 (latest .deb from avasys)
xsane:0.996-2ubuntu1.1
xsane-common:0.996-2ubuntu1.1
sane:1.0.14-7
libsane:1.0.20-4ubuntu3
[Code]...
If I attempt to run as with escalated privileges, I don't get the error pop up window, but the window goes dark as if it stops responding and then it just closes with no stdout except ,"WARNING: Unhandled message: interface=org.freedesktop.DBus.Introspectable, path=/, member=Introspect"
View 4 Replies
View Related
Mar 26, 2009
After a recent upgrade I'm now completely unable to log in to my computer. GDM autologin lets me start my computer and enter gnome as before, but su and sudo wont let me access my root account. If I start in single-user mode and try to change my root password with the command passwd I drop back to the shell after entering my current password, no error messages. Same with su and sudo, just drop back to the terminal without error messages. I am running ubuntu jaunty, any idea what's happened?
View 2 Replies
View Related
Feb 23, 2010
Servlet were working. The next to last yum upgrade broke servlet.
I now get a error 404
Object not found!
The requested URL was not found on this server. If you entered the URL manually please check your spelling and try again.
I have not been able to find any docs on how
/usr/share/java/tomcat5-jsp-2.0-api.jar
or
/usr/share/java/tomcat5-servlet-2.4-api.jar
are connected to apache httpd.
use to be mod_jserv
then a tomcat.conf
but can't find on centos distro.
View 2 Replies
View Related
Mar 20, 2011
After yesterday's apt-get dist-upgrade, I lost my higher screen resolutions. Only had 800x600 and 640x480. After trying to re-install the Nvidia drivers several different ways without success, I ended up purging xorg and xserver and then starting from scratch, re-installing the drivers. In doing so, I either found the problem, or created another, ha.I think part of the problem was that I mixed Nvidia proprietary and debian installations and the update broke the drivers.I am now unable to install xorg or xserver because I can not remove/purge libgl1-nvidia-alternatives.
View 2 Replies
View Related
Nov 30, 2010
I*had an update today and, since, Flash full screen is jerky and the sound comes as through a PVC*pipe.nybody has this problem?How do I find the updates that arrived today?*Is it possible to revert to a precedent version?
View 2 Replies
View Related
May 19, 2010
I have 4 drives in my system. Two are SATA and configured in a RAID 1. This is my main drive for the system. The other two drives are IDE drives used to bulk temp storage. Before the upgrade my RAID drives were:
/dev/sda
/dev/sdb
I'm not sure what the IDE drives were. Now after the upgrade the IDE drives are:
/dev/sda
/dev/sdb
and the RAID SATA drives are:
/dev/sdc
/dev/sdd
Needless to say on reboot the raid blow up and the system would not boot. I was able to get it working for now by removing the IDE drives. My current mdadm.conf file is as follows:
DEVICE partitions
ARRAY /dev/md1 level=raid1 num-devices=3 UUID=20fd5b92:860d9ca3:57d3b65c:14fcf2fb
devices=/dev/sda2,/dev/sdb2
ARRAY /dev/md0 level=raid1 num-devices=3 UUID=16401201:52cf4cc0:27286d7a:ac5234f7
devices=/dev/sda1,/dev/sdb1
MAILADDR root
Now I assume that I could change the devices to the new devices names. However I was hoping for a better way to do this. The IDE drives are only semi permanent. Is there a way to configure mdadm with partition labels like you can in fstab?
View 1 Replies
View Related
Dec 12, 2014
Yesterday, I ran a security update that upgraded my Squeeze kernel from 2.6.32-48squeeze8 to 2.6.32-48squeeze9.
Ever since then, my suspend to ram (STR) function is broken.
The machine will suspend normally, but will not resume. When I try to awaken the machine, I can hear the fan in the tower start up (the subject machine is a desktop computer, please see below for specifics), but the machine seems to be otherwise dead (e.g. the monitor stays blank, pressing the "caps lock" key on my keyboard does not activate said keyboard's "caps lock" led, Ctrl-Alt-F[x] has no effect, etc). My only recourse at that point is a hardware reset (ouch!).
I tried running Code: Select allpm-suspend from a terminal, with no joy. Same result running Code: Select allecho -n "mem" > /sys/power/state from a terminal.
I checked the /var/log/pm-suspend.log file and noticed that each Code: Select all...performing suspend line used to (before said kernel upgrade) be directly followed by a Code: Select all...Awake. line, but, now, all said Code: Select all...performing suspend lines are followed by an Code: Select allInitial commandline parameters... line.
Before this, STR has worked well ever since I first loaded Squeeze on this machine back in 2012.
Code: Select allSqueeze 6.0.10; 2.6.32-5-amd64
Intel i7-980 Gulftown CPU
Asus P6X58D Premium Motherboard
EVGA GeForce GTS-450 Graphics Card
G.SKILL Ripjaw DDR3-1600, PC3-12800, 1.5v RAM (6x4GB sticks, 24GB total)
Crucial RealSSD C300 128GB SSD
Western Digital Caviar Black 1TB HDD
Corsair HX850 PSU
[CODE]
View 14 Replies
View Related
Jun 23, 2015
I'm running debian testing on my laptop. This morning when I ran apt-get update && apt-get dist-upgrade, I was greeted by the following errors:
Code: Select all
Calculating upgrade... Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information to resolve the situation:
The following packages have unmet dependencies:
libcurl3-gnutls : Depends: librtmp1 (>= 2.4+20131018.git79459a2-3~) but it is not going to be installed
E: Error, pkgProblemResolver::Resolve generated breaks, this may be caused by held packages.
A quick search found out that package librtmp1(2:2.4~20150315.gita107cef9b-dmo1) is already installed.
I do have some packages set on hold, however I don't think that's the problem:
Code: Select all$ dpkg --get-selections | grep hold
hostapd hold
libgcrypt11:amd64 hold
linux-image-amd64 hold
My sources.list on which I haven't touched for a very long time:
Code: Select alldeb http://mirrors.163.com/debian/ testing main non-free contrib
deb-src http://mirrors.163.com/debian/ testing main non-free contrib
deb http://mirrors.163.com/debian-security/ testing/updates main contrib non-free
deb-src http://mirrors.163.com/debian-security/ testing/updates main contrib non-free
deb http://mirrors.163.com/debian/ testing-updates main contrib non-free
deb-src http://mirrors.163.com/debian/ testing-updates main contrib non-free
View 2 Replies
View Related
